Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 86/468 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

• How to scan local network (LAN) for connected devices (Mac OS)

  - by smotchkkiss

  I'm basically looking for something like this but available on Mac. I am trying to connect a new workstation to our wireless multifunction printer and I'm having a hell of a time getting the device to spit out an IP for me to connect to. Is there a way I can scan the network somehow? If it makes a difference, the new workstation is using Mac OS X 10.6 Thanks in advance :)

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• Embedded Net DVR camera1 failed to start preview!

  - by user44212

  I am gettig the following error as "Embedded Net DVR camera1 failed to start preview!" when we are trying to login and view the preview of the cameras on the DVR 8116HCI-S Standalone. There is an IP Address assigned to the same via which we access the same. I checked the site for information here http://www.hikvision.com/en/Products_show.asp?id=32. But could not find any useful information relating to the error message. We can access the same via login in from one machine but we are not able to access it from more than one machine.

  Read the article

• Cross platform support for network attached USB hubs?

  - by larsks

  I am looking at network-attached USB hubs in order to run licensed software in a virtualized environment when hardware dongles are required. Are there any solutions that will work with both Linux and Windows? Most of the dedicated devices -- such as the Zonet ZUH2214 or the (oddly expensive) Digi AnywherUSB/2 -- appear to be Windows-only. Linux has the the USB/IP project, for which there appear to be Windows drivers, but the last "News" post on the site was in 2007, so I'm not entirely confident about the viability of the project. Has anyone out there found a solution that will work well in both environments?

  Read the article

• setup Mac Book Wifi interface as Wifi hotspot using specific DHCP option

  - by srjohnhuang

  I want to using my Mac Book as an access point. Besides that I also need to configure its DHCP server to not provide DNS info. For example, Mac Books AP's ssid is "MacBookHotspot". While my iPhone connected to "MacBookHotspot", I want the Wifi info displayed my iPhone would be looked like: IP ADDRESS DHCP(tab) IP Address 192.168.0.1 Subnet Mask 255.255.255.0 Router 192.168.0.254 DNS Search Domains Client ID (key point: DNS filed is blank) Does anyone have any good suggestion? Thanks!

  Read the article

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• Intermittent "Lost connection to MySQL server at 'reading initial communication packet'"

  - by db2

  Our web environment consists of two servers. Web front-end. Dell PowerEdge R610, RHEL 5.5, Apache 2.2.17, php 5.2.14. Database server. Dell PowerEdge R710, Windows 2008 R2 Standard x64, MySQL 5.5.11-log x64. Normally these two work perfectly fine together. However, when I try to get them talking via a dedicated LAN on their secondary NICs (each machine has four of them), things get flaky. I have NIC #2 on both machines configured on the 172.16.1.0/24 subnet, with no gateway or DNS servers (obviously, since it's just those two systems), and I put the private IP address of each machine into the hosts file of the other. The routing tables on both machines look okay after I do this. I've tried this with both a crossover cable draped directly between the two NICs, and also via a dedicated vlan on the switch in the rack. In either case, I get intermittent connection problems. It's a fairly small percentage of connections that fail, but it's enough to cause a significant problem, and I have to switch back to the main network connection, which will contend with all the other traffic and hosts on the switch. The full error message that appears in the application log: SQLSTATE[HY000] [2013] Lost connection to MySQL server at 'reading initial communication packet', system error: 110 Am I doing something really dumb that's causing this to not work properly? Anything I can check in MySQL that would explain why it's failing to connect occasionally?

  Read the article

• TP-LINK TD-W8151N Modem/router as just wi-fi router

  - by Reshma

  I am planning to buy TP-LINK ADSL wifi router (model TD-W8151N) for my Internet connection which provides Internet through ADSL telephone line. I am also planning to take cable internet in a few months which provides internet through a LAN cable without the need of any modem. So I would like to have my modem work for both connections which I am using. When using cable internet I want this TP-Link modem to work just as a wireless router (so that I can have the freedom to use my laptop in different rooms instead of sitting at a place by plugging in that cable). Is it possible to use this modem in that way? I don't have much knowledge about these things except that I can configure things as instructed. Please suggest me whether I should go ahead and buy this one or if there is any other modem in your view which can serve both my purposes, let me know. Operating System I am using: Windows 7

  Read the article

• IP alias lost when changing main IP

  - by rmflow

  my /etc/network/interfaces: auto eth0 iface eth0 inet static address 192.168.3.75 netmask 255.255.255.0 gateway 192.168.3.0 Situation 1: After linux booted I set an IP alias: ifconfig eth0:0 192.168.3.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.3.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 is lost! Situation 2: After linux booted I set an IP alias: ifconfig eth0:0 192.168.4.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.4.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 stays! How do I properly change main IP, so all my aliases are not lost?

  Read the article

• Logging network activity of LAMP server using BASH

  - by Yarin

  I've got a Fedora LAMP server on Amazon EC2 functioning as a HTTP pseudo-proxy (Sorry, don't know the terminology- It's not a true proxy where requests are relayed through apache, rather client requests are being translated by a PHP script, which then sends a new request.) I'd like to be able to fully log the HTTP cycle CLIENT - PROXY PROXY - SERVICE SERVICE - PROXY PROXY - CLIENT I'm hoping to do this using BASH tools- thinking netcat? Looking for advice and examples. Thanks!

  Read the article

• Windows XP IIS5 performance across Network

  - by davidsleeps

  Hi, Just wondering whether Windows XP with IIS5 running needs any extra configuration to be suitable as a web server...I'm not considering using this for anything other than a web server on a small network for testing development etc One of the reasons I'm concerned though is that we've deployed an asp.net application to a workstation with Windows XP, and running the application using a browser on the machine (so accessing it through localhost/myApp/page.aspx and not accessing it through the network) runs the application really quickly. If another machine on the LAN accesses the same page (using http://ComputerName/myApp/page.apx) then the whole application runs noticeably slower...yet the computers are connected on a gigabit switch...so I wouldn't have thought network latency or bandwidth could be an issue... Does Windows XP need anything etc enabled or changed or network settings for it to work correctly?

  Read the article

• Browsing Playstation 3 from Ubuntu Box

  - by zfranciscus

  Hi, My Goal here is to be able to transfer files from my Ubuntu 10.04 box to my PS3 over a wireless network. My PS3 and my Ubuntu Box is on the same home network. These are some stuff that I tried: I can't see my PS 3 from 'Places ? Network' nor other computer that is running on windows. I am still puzzled by this fact. I have not tried ping-ing my PS3. I'll try that later today and post the result in the forum I install PS3MediaServer (http://code.google.com/p/ps3mediaserver/). Someone in the PS3 chat forum (http://www.ps3chat.com/playstation-3...lp-please.html) claims that it will enable your ubuntu box to browse PS3. So I downloaded PS3MediaServer, and ran the software. The status tab keep showing "Waiting ...". It seems that PS3MediaServer can't find my PS3. Some how I feel that 1 and 2 are related somehow.Perhaps that there is something wrong with my Ubuntu network settings that is preventing my ubuntu box from looking up other device on the network. I can go to the Internet fine, but I can't see other device on my network. Does anyone have any experience in this area. I would like to hear your experience and perhaps some solution. Any kind of hints or help will be greatly appreciated. Cheers

  Read the article

• Why can I not access the internet when Windows 7 finds no issue with the ethernet connection and the network can see my device?

  - by WannabeCoder

  So I just moved from a house to an apartment. In the house and the apartment I had Uverse set up - and in both I had my desktop connected via a ~40 foot long cat5 cable. However, upon moving to the apartment I found that my ethernet connection no longer provides internet. This would seem like a mundane problem if not for: The router can see the computer on the network Windows 7 (the desktop's OS) detects no problems with the ethernet connection. Connections over the internet (i.e. browser windows, Pandora, etc.) do not immediately fail. Instead they load for 2 minutes and then finally give up. Devices connected over the Wifi (PS4, Laptop) access the internet just fine While removing the cat5 cable from my house, I accidentally damaged the locking tab but managed to bend it back into the appropriate position. I would suspect that a bad cat5 cable might be to blame if not for the above issues (thought I've heard bad cat5 cables cause the most nonsensical problems) and the fact that I tested the cat5 cable by having it share internet between my laptop (working internet) to my desktop and it functioned just fine and provided the desktop with internet. My ipconfig /all successfully finds a default gateway, DHCP server, and DNS server. What could possibly be causing the problem?

  Read the article

• Using an audio cable (or similar) to create unidirectional communication from a secure server

  - by makerofthings7

  I'm interested in exploring how a semi-offline Root CA can be used to update CRLs to the sub CA's. This answer on Security.SE mentions using an audio cable for this purpose. Doe anyone have details on how an Audio cable (or similar) can be used to create a unidirectional path of communication? Since I'm a .Net programmer, I'm also open to code samples, drivers, etc that may enable this scenario.

  Read the article

• How to backup a networked drive?

  - by nute

  I have a networked drive (Iomega Media Drive). To be safe in case the drives crashes, I've decided to buy an additional networked drive (WD MyBook World). Now, how do I backup one onto the other continuously? The WD drive came with a backup software (trial version, they didn't say that when i bought it), however it doesn't allow me to select a networked drive, only local drives. How do I backup a NETWORKED DRIVE ONTO A NETWORKED DRIVE? Thanks

  Read the article

• Wicd not playing well with networks that utilize network access control

  - by Sion

  Starting a couple months ago (might be able to find exact date if necessary) my installation of Wicd stopped being able to see wireless networks that use NAC (Network Access Control) such as Aruba networks. But if I shut down Wicd and start NetworkManager I can connect to said networks and log in to them depending on what the NAC requires. This is the current wicd package installed: net-misc/wicd-1.7.1_pre20111210-r1 This is how I manipulate the network manager running: su -c'/etc/init.d/wicd stop; /etc/init.d/NetworkManager start' What would cause this specific of a problem to occur?

  Read the article

• internet disconnects

  - by Smokezzaj

  Internet disconnects and reconnects, computer is in a peer to peer workstation with two other computers XP o/s. Only one computer has this problem the other two don't disconnect. Computer's connect to switch no router is being used. Ipconfig shows a DHCP connection, local area connection status shows packets being sent out but packets are not being received or being received at a extremely slow rate. Tried Winstock tool, reinstalling network card driver, restored to previous date, checked ethernet cable and release/renew IP.

  Read the article

• How to redirect all Internet traffic to OpenVPN Server

  - by JuliaS

  I have seen working solutions around the issue of forcing Internet traffic to go through the OpenVPN server but they are all done in Linux, all I want to know is how to add an entry to the route table in windows to make this happen. connectivity between the client and server is fine, my Windows 7 client can establish a connection to the Windows 2008 Server, but when established Internet traffic is still going from the local Windows 7 machine. Here are the details: Server: Windows 2008 Server with one NIC OpenVPN IP Address: 192.168.0.1 Local NIC IP Address (connects the server to the Internet): 10.242.69.107 Client: Windows 7 with one NIC OpenVPN IP Address: 192.168.0.2 ISP allocated IP Address: 10.0.8.2 (gateway 10.0.8.1) Server OpenVPN Config: dev tun ifconfig 192.168.0.1 192.168.0.2 secret static.key push "redirect-gateway def1" Client OpenVPN Config: remote xxx.xxx.com dev tun ifconfig 192.168.0.2 192.168.0.1 secret static.key I'm not an expert with adding routes...etc. I would be grateful if someone could let me know how to add this entry in my server/client route table. EDIT: Output from the client's netstat -rnv IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.8.1 10.0.8.2 20 10.0.8.0 255.255.255.252 On-link 10.0.8.2 276 10.0.8.2 255.255.255.255 On-link 10.0.8.2 276 10.0.8.3 255.255.255.255 On-link 10.0.8.2 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.252 On-link 192.168.0.2 286 192.168.0.2 255.255.255.255 On-link 192.168.0.2 286 192.168.0.3 255.255.255.255 On-link 192.168.0.2 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.8.2 276 224.0.0.0 240.0.0.0 On-link 192.168.0.2 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.8.2 276 255.255.255.255 255.255.255.255 On-link 192.168.0.2 286 ===========================================================================

  Read the article

• Windows XP does not list WPA wireless networks

  - by Tomalak

  What can be the reason that Windows XP does not show WPA-encrypted wireless networks? The laptop I have problems with is an older model (Toshiba Satellite Pro 6100) with Windows XP SP3 on it, fresh install. The wireless network card in it is an Agere product that lists as "Toshiba Wireless LAN Mini PCI Card". The networks showed up perfectly before I first tried to connect to one (it was set to WPA2). The connection failed (the card supports WPA only), then something must have happend and Windows hides these networks now. A manually configured WPA setup via Windows' own wizard works, I'm using it right now. The network just won't show up in the list of available network on its own. I suspect that XP incorrectly set a flag somewhere that this network card does not support WPA. Is there such a flag, and if so, how can I change it back?

  Read the article

• NIC models for HVM guests in Xen 4.0

  - by Jed Daniels

  Is there a list of NIC models that I should use with various HVM guests in Xen 4.0? Is there even a list of possible choices for the model=field? I'm planning on running both Windows and FreeBSD guests on the particular Xen box that I'm configuring now, and ideally I'd like a setting that can work on both of them and get me gigabit speeds without a lot of extra hassle loading special drivers (similar to VMware's e1000 NIC option). Any suggestions? The vif line I'm currently using in my config is: vif = [ 'type=ioemu,bridge=eth0,model=ne2k_pci,script=vif-ovs' ] This works in my Windows XP SP3 VM, but is only recognized as a 10Mbit interface. Changing to model=e1000 or model=i82557b resulted in Windows not being able to find a driver for the NIC.

  Read the article

• Most secure way of connecting an intranet to an external server

  - by Eitan

  I have an internal server that hosts an asp.net intranet application. I want to keep it completely and utterly secure and private however we need to expose some information through a WCF service to another server which hosts our external websites which CAN be accessed by the public. What is the best way to pass information between the two servers with regards to an IT setup, while keeping the intranet in house server completely secure and inaccessible? I've heard VPN was the way to go but I wanted to be sure this was the safest way. Another question what would be the most secure way of passing data in the WCF service?

  Read the article

• "entering link in browser" to "finding route to host" how it works?

  - by Algorist

  Hi, Is there a wiki or book, which explains what happens when user enters a link in the browser, and how the dns is resolved, how the router finds the route to the host etc.. I am mainly interested in routing the packets. Thank you

  Read the article

• Using Static Public IPs and Private DHCP IPs on the Same Router

  - by Andrew Larsson

  I have a subnet of public IP addresses that my ISP has provided me with. They are routed through my router (how profound) that has a a static IP. I have successfully assigned the IPs from that subnet to various devices on my network. This works just fine, they get their own public IP, they can access the Internet, and the Internet can access them. However, I would like to also assign some private IPs on my network through that same router and put them behind NAT. Is this even possible? Could a VLAN be of use? I would like to avoid putting another router on the network, which makes this is quite an awkward question.

  Read the article

• How do I see what connections are being made?

  - by Coldblackice

  My DDWRT router is showing that my computer has a connection count around 600! The router is at 100% CPU use. How can I see what's making all the connections? So far, I've opened up Resource Monitor and checked the network tab. I can sort by which program is using the most network bandwidth (Pale Moon browser), but I can't see what's making all of the connections. Or rather, where all the connections are being toward (trying to find what tab must be making all of these connections). I've also tried netstat -A, but it apparently doesn't show the actual number of connections being made. At least, the list of established connections isn't very long, by any means (like enough to account for the 500+ connections apparently being made.

  Read the article

• WHS - Windows Update Failure

  - by Kyle B.

  Clicking "Update Now..." inside my EX470 control panel for Windows Update produces the following error message: "Windows Home Server updates installation can not complete. Please try again later. If the problem persists, please restart the server." I have rebooted the server numerous times, and I have also used remote desktop to connect to the machine to perform the update this way, however the browser is unable to pull up http://windowsupdate.microsoft.com. This is very strange behavior because I am able to access all other sites (gmail.com, serverfault.com, etc). Would it be possible for someone to explain to me how I can check to see what is blocking the connection of this device, which apparently has a valid internet connection, to the Microsoft Windows Update site? note #1 Using the shortcut: %SystemRoot%\system32\wupdmgr.exe does not work either. It says "Connecting to 65.55.200.155..." but nothing ever happens. This is strange because all other sites seem fine. Also, I can connect to windowsupdate.microsoft.com on my local desktop so I know this is running as well

  Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >