Search Results

Search found 29636 results on 1186 pages for 'fine uploader'.

Page 860/1186 | < Previous Page | 856 857 858 859 860 861 862 863 864 865 866 867  | Next Page >

• Computer making strange sound when turned on, ever since power outage

  - by Dot NET

  Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

  Read the article

• Strange Photoshop Problem: Can not select, zoom, paint, option button 'locked'

  - by nikcub

  I have a very strange problem with Photoshop. I can not use any of the tools, since the cursor appears 'locked'. If I select v on my keyboard, it goes to the zoom tool, but the cursor does not change. If I select the paintbrush tool, I can only paint if I hold down the option key. This is what the cursor look like (I had to paint it since I couldn't capture it). It is a rectangle with two lines through it. I am running Photoshop CS4 on a Macbook Pro with Mac OS X 10.6.6. Using both the trackpad and an external Logitech MX5000 mouse I see the same issue. This started when I fired up Photoshop today for the first time in a while. I can't remember changing any options or doing anything that could cause this. Is it possible that the option key is somehow locked in place, or there is some equivalent of num lock on? Very strange problem, I would appreciate any help anybody can offer. Edit: To add, the icon remains the same within all the menu options - it never goes back to being just a normal mouse cursor. Also, right click works fine, and if I hold down option, the cursor goes back to normal and I can paint with it. I can't use Marquee, Lasso, Crop, Type etc. even with option held down. When I go into Bridge, it is the same icon.

  Read the article

• Euro character messed up during FTP transfer

  - by djechelon

  My customer is using a very outdated ecommerce management system on my hosting service. For that product, no support is being provided anymore by the vendor. Brief explanation: the shop website, that claims to run under LAMP stack, is built by an old Visual Basic Windows application running on MS Access. The user constructs the shop, defines the HTML template, adds products and categories, etc. Then the VB exe builds the PHP pages (one for each template page) and the SQL script to run on MySQL. It also uploads everything via FTP and runs the installation/upgrade script on its own. The problem Browsing the website, many products' descriptions are cut before the euro sign. For example, what was supposed to be "Product price €1000" becomes "Product price" The analysis MySQL contains a cutted description until the € sign, so it's not PHP fault The Access databases contain full description with € sign, so it's not fault of the webmaster writing bad description or eDisplay cutting them The SQL that will run once the site gets uploaded, stored on my local machine before upload, contains the € sign The same script, after being FTPed by eDisplay and opened with nano from SSH, shows the € sign messed up like this: ^À vsftpd log reports (obfuscated for privacy) Sat Dec 15 11:16:57 2012 22 xxx.xxx.128.13 1112727 /srv/www/domains/xxxxxx.it/htdocs/db.sql b _ i r xxxxxxx ftp 0 * c which seems to be a binary transfer (and also a huge security vulnerability because you can download the whole database from unauthenticated HTTP) The eDisplay internal FTP client provides no option for ascii/binary transfer modes [Add] Trying to manually upload the SQL file via SFTP shows messing up euro [Add2] Trying to manually upload using Xftp client with explicit ASCII mode doesn't fix too It looks like the file gets uploaded as binary. Perhaps on the customer's previous host it all worked fine because that was a Windows host. The server It's an Azure virtual machine running openSUSE 12.2 with both vsftpd and openSSH The question Without asking the customer to manually upload files using FileZilla or replacing € with &euro;, because he refuses, what can I do on server side to prevent vsftpd to screw up euro sign?

  Read the article

• Recovering corrupted VB.NET Form file?

  - by Omega

  Good day. This question is directly related to this one I made here: http://stackoverflow.com/questions/4911099/there-is-no-editor-available-for-form1-vb-error There, I was working on my VB.NET 2010 Express application, I saved, then a blackout came and now, apparently, I can't view the designer nor code of my Form file (Form1.vb). On StackOverflow, I was recommended to check for the From1.vb file, and try to open it on Notepad. If nothing appeared, it would mean that my file was corrupted. I open it on Notepad, and I get a blank file. It is 27kb, but it only has blank spaces. So I assume it is corrupted. I was told this place was better for dealing with corrupted files, about techniques to recover them. I use Windows7, VB.NET 2010 Express. I run Windows7 on Parallels Desktop, Mac OS X. However, I do not believe that is the problem, most likely it was that damned blackout... this is the first time that happens to me. VB.NET worked just fine for me all time (about a month and half). Thank you.

  Read the article

• Apache: getting proxy, rewrite, and SSL to play nice

  - by Rich M

  Hi, I'm having loads of trouble trying to integrate proxy, rewrite, and SSL altogether in Apache 2. A brief history, my application runs on port 8080 and before adding SSL, I used proxy to strip the 8080 from the url's to and from the server. So instead of www.example.com:8080/myapp, the client app accessed everything via www.example.com/myapp Here was the conf the accomplished this: ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> ProxyPass /myapp http://www.example.com:8080/myapp ProxyPassReverse /myapp http://www.example.com:8080/myapp What I'm trying to do now is force all requests to myapp to be HTTPS, and then have those SSL requests follow the same proxy rules that strip out the port number as my application used to. Simply changing the ports 8080 to 8443 in the ProxyPass lines does not accomplish this. Unfortunately I'm not an expert in Apache, and my skills of trial and error are already reaching the end of the line. RewriteEngine On RewriteCond %{HTTPS} off RewriteRule myapp/* https://%{HTTP_HOST}%{REQUEST_URI} ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> SSLProxyEngine on ProxyPass /myapp https://www.example.com:8443/mloyalty ProxyPassReverse /myapp https://www.example.com:8433/mloyalty As this stands, a request to anything on the server other than /myapp load fine with http. If I make a browser http request to /mypp it then redirects to https:// www.example.com:8443/myapp , which is not the desired behavior. Links within the application then resolve to https:// www.example.com/myapp/linkedPage , which is desirable. Browser requests (http and https) to anything one level beyond just /myapp ie. /myapp/mycontext resolve to https:// www.example.com/myapp/mycontext without the port. I'm not sure what other information there is for me to give, but I think my goals should be clear.

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Serious 64-bit laptop

  - by Daniel Gehriger

  For the past couple of years, I have been using an IBM Thinkpad T60p for daily work (software development, desktop & embedded). I am extremely satisfied with this machine, due to its robustness. It also has a few features I depend on: a high resolution display: 15.0" TFT FlexView display with 1600x1200 (UXGA); excellent keyboard; decent graphics and CPU performance. Some of the software I develop benefits from larger amounts of RAM, and 3GB (Windows 7 32-bit) or 4GB (Windows 7 64-bit on T60p) are no longer sufficient. My customers run desktop computers with 20GB and more, and I need to have at least 8GB to at least be able to run reasonable test cases. So I'm shopping around for a new laptop, but I'm struggling to find anything that matches my requirements: must run Windows 7 64-bit Pro or higher; must support at least 8GB of RAM (more is better) high screen resolution! While I prefer 4:3 I can live with wide screen. But I really hope to find something with a vertical screen resolution similar to what I have now... portable, so < 16" but = 14" I realize that FlexView isn't available anymore, but I'd like to avoid a glossy screen if possible. decent (not more) graphics performance, ideally hybrid (I'm doing a lot of CAD, never games). good keyboard reasonable CPU -- but I'm still fine with my current Core 2 Duo, so that shouldn't be too complicated. The T60p fits all those requirements, except the 8GB of RAM. Can you help me find a current notebook that would match most of them? I don't mind changing brand. Thanks!

  Read the article

• Some SVN Repositories not working - 405

  - by Webnet

  I have 2 groups of repositories, web and engineering. I setup web about 3 months ago and it works great, I'm trying to move engineering over to this same SVN server and I'm getting a PROPFIND of /svn/engineering/main: 405 Method Not Allowed error when I try to do a checkout. I can checkout/commit for /svn/web just fine dav_svn.conf This is the only thing uncommented in this file.... <Location /svn/web> DAV svn SVNParentPath /var/svn-repos/web AuthType Basic AuthName "SVN Repository" AuthUserFile /etc/svn-auth-file Require valid-user </Location> <Location /svn/engineering> DAV svn SVNParentPath /var/svn-repos/engineering AuthType Basic AuthName "SVN Repository" AuthUserFile /etc/svn-auth-file Require valid-user </Location> /var/svn-repos/ drwxrwx--- 3 www-data subversion 4096 2010-06-11 11:57 engineering drwxrwx--- 5 www-data subversion 4096 2010-04-07 15:41 web /var/svn-repos/web - WORKING drwxrwx--- 7 www-data subversion 4096 2010-04-07 16:50 site1.com drwxrwx--- 7 www-data subversion 4096 2010-03-29 16:42 site2.com drwxrwx--- 7 www-data subversion 4096 2010-03-31 12:52 site3.com /var/svn-repos/engineering - NOT WORKING drwxrwx--- 6 www-data subversion 4096 2010-06-11 11:56 main I get to the bottom and now realize that there's a 6 on that last one not a 7..... what does that number mean?

  Read the article

• Windows 7 - Can't get my TV working as primary display with nVidia 7900GS

  - by Daniel Schaffer

  I just installed Windows 7 Ultimate 64 RTM (from MSDN) on my HTPC, which is connected to a 42" Magnavox LCD TV via component cables to my nVidia 7900GS. Everything was fine through the installation until I went to install the official driver from nVidia. Towards the end of the installation, the TV blinked off and wouldn't come back on. I went and got an LCD monitor and plugged it into a DVI port and the monitor came right up, but was automatically selected as the primary display. Now, if I set the TV to be the primary display, the TV just blanks until I hit escape to cancel the "settings have changed, do you want to keep them" dialog. Any suggestions? Update: I'm able to set the TV as the primary display using the Windows 7 "screen resolution" configuration panel. However, if I try to remove the LCD monitor either by unplugging it or using the configuration, the TV blanks out again. Update 2: This setup was working correctly in Vista Home Premium 32-bit. Update 3: I've uninstalled the nVidia driver and am using the driver that Windows Update installed. As much as this offends my geek sensibilities (must use the "right" driver!!), well, It Works™.

  Read the article

• ssh hangs on "Last login" line

  - by Pavel H

  This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• Cannot install windows. Compaq Presario CQ62

  - by Matthew

  I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

  Read the article

• How do I setup an Alias on Apache with XAMPP on Linux ? (Permission problem)

  - by knarf

  XAMPP works fine but I want to have http://localhost/f to point to /home/knarf/prog/php/fwyxz. I've chmod -R 777 /home/knarf/prog/php/fwyxz I've added Alias /f /home/knarf/prog/php/fwyxz at the end of the httpd.conf And when I try to access it, I get a 403. From the apache error_log: [error] [client 127.0.0.1] (13)Permission denied: access to /f denied. I've already tried several solutions (userdir and symlinks) but they both failed with the same error. I've also tried to add this after the Alias: <Directory "/home/knarf/prog/php/fwyxz"> Order allow,deny Allow from all </Directory> But again, permission denied. Now if I change the User/Group under which apache runs from nobody to knarf, it seems to work (static files are ok) but PHP can't use/initialize sessions : [error] [client 127.0.0.1] PHP Warning: session_start() [function.session-start]: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in /home/knarf/prog/php/fwyxz/index.php on line 3 [error] [client 127.0.0.1] PHP Warning: Unknown: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in Unknown on line 0 [error] [client 127.0.0.1] PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct () in Unknown on line 0 This is really frustrating.

  Read the article

• Nokia E75 Mail for Exchange

  - by Sebastian

  Hi, I have a SBS2003 runing Exchange Server 2003 SP2. My OWA has a godaddy certificate valid for 3 years to come installed. HTTPS works fine for OWA. The certificate has also been copied into the Nokia E95 I am trying to syncronize my Nokia E75 via Mail for Exchange to my mail account on the Exchange server. These are the steps i use: Menu Email New Start Select Internet Gateway Than i enter the details: [email protected] I select company email Mail for Exchange In the domain menu i enter : mydomain In the username/password menu i enter : myusername/mypassword In the server menu i enter : mail.mydomain.com (where the DNS resolves into the server's IP address) In the secure access i select : Internet / Secure / 443 NOTE : port 443 has been opened on my SBOX and forwarded to the exchange server. On IIS default website properties directory security secure communications edit the "Require Secure Channel SSL" is enabled. However, when i try to sync my phone i get the following error code: * Mail for Exch permissions illegal. Check permission configuration. * The phone log gives the following information : Username or Password Illegal. Correct Username and/or Password in the profile options. I've tried speaking with the Phone service support but they cannot identify the problem. Any help will be much apreciated.

  Read the article

• User profile service fails

  - by s.r.a

  I have Windows 7 and 3 drives on my HDD. The second drive is D:\, and there are some files in that. I decided to install 8.1 Enterprise so I installed it in dual boot manner beside 7 and in D:\ drive which as I said was not empty and when installing 8.1, I didn't format the D:. I installed 8.1 successfully in D:\ and it was working fine. One time which I came up with 7, I thought I should arrange the 8.1 folders in D: to be separated from the other non-8.1 folders, so I created a new folder named it "Windows 8.1" and cut all 8.1 folders and pasted them into that new folder. Now my D: drive was arranged. When I restart the PC, I selected the 8.1 to start with, but it didn't come up like before and instead, it shows now a blue screen (not the blue screen of death!) and the time is shown in left-down corner of it. When I click the screen this message appears: The User Profile Service service Failed the sign-in. User Profile can not be loaded. I know two things: 1- The problem is to do with that cutting and pasting the 8.1 folders to be arranged. And 2- If I reinstall the 8.1, the problem will be solved (but if I don't do that cutting and pasting again!) Is there any simpler way to solve the issue and have the two OSs with each other?

  Read the article

• De-duplicating backup tool on a block basis? [closed]

  - by SST

  I am looking for an (ideally free as in speech or beer) backup tool for Unix-like OS which can store deduplicated backups, i.e. only nonredundant content takes up additional space. I already looked at dirvish (my first candidate) and rsnapshot which use hardlinks to achieve deduplication on a per-file level. However, as I want to back up large files (Thunderbird mailboxes 3GB, VMware images 10GB), such file are stored again entirely even if just a few bytes change. Then there are rsync-based tools like rdiff-backup which only store deltas and a current mirror. However, as the deltas are generated against each previous mirror, it is difficult to fine-tune the retention granularity (only keep one backup after a week, etc.) because the deltas would have to be re-evaluated. Another approach is to partition content into blocks and store each block only if it is not stored yet, otherwise just linking it to the first occurrence. The only tool I know of that does this by now is obnam (http://liw.fi/obnam), and it even supports zlib-compression and gpg-encryption -- nice! But it is very slow, AFAICT. Does any one know any other, solid backup software which supports deduplication on a sub-file level, ideally with at least some management options (show/select/delete generations...)?

  Read the article

• Connecting SVN from Remote Server

  - by Ashish

  I have hosted my repository in assebbla & it works fine. now I want to write a script that can automate the build process : 1. Take the code from assembla repository 2. Make a dump and copy it onto my web server. what I have researched from net states that use of commands like svn co svn+ssh://[email protected]/home/svn/test I believe I need to open Shell on my server and type these commands but shell has been disabled from my server admin. I tried to run the same from php using exec , admin has disabled that too. (am using shared hosting and want to do a automated deployment using these simple steps. i don't want to bring my local system in this process) now am not sure even if I get the shell access open to my server these commands like svn will work there as I don't have SVN installed on my server (its installed on assembla). kindly let me know if any more explanation is required regarding the same or if am going on the wrong track. Am a newbie so please be descriptive in answering :) Thanx in advance Ace

  Read the article

• Router that allows custom Dynamic DNS server [closed]

  - by Thuy

  I've made my own DDNS service and it works fine using an application running on clients to update the IP. But if for some reason I don't have the choice of using my software and instead I need to use a router to update the IP, it becomes troublesome. For example, I needed to setup IPsec from a customer to me and the customers router/firewall (netgear srx5308) has a dynamic IP which is given from the ISP which can't offer static IPs. So it needs to use dynamic dns for it to work. In this case there really isn't a client to run the software on since it's a router/firewall. Unfortunately it seems that most routers are rather unfriendly towards custom DDNS solutions and most offer only dyndns.com or similar templates. Which was the case with this router too. Leaving me with no way to use my own dynamic dns server IP. I have the option of switching out the customers router and I've been looking around for alternatives and other routers/solutions and I was wondering if anyone on this great site might have been in a similar situation or might just know about some router/firewall that is more friendly towards custom ddns solutions that I might be able to use. Thanks in advance for any help or guidance!

  Read the article

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Ubuntu 11.04 fresh install - "Input signal out of range" or "Mode not supported..."

  - by Dennis

  I recently installed Ubuntu 11.04 using a CD .iso. Installation went fine. Upon completion I rebooted and after a second or two I got a black screen with the message "Input signal out of range". And there it sits... Read a few things about how this could be related to screen resolution, refresh rate, etc. For the heck of it I tried a different monitor. The result is the same but the message provides some clues - "Mode not supported - H:92.7kHz, V:58.3Hz" (the latter is Hz; not kHz). So my thought is that I should probably be able to use the 11.04 install disc to "Try out Ubuntu", find and edit some file that was created by the install with the correct values. Problem is, I am not too sure what I am supposed to edit. Looked at the xorg.conf file but this is so minimal at this point I am not sure it is where I want to go. By the way, the monitor is an I-Inc ix191a. Anyone have any ideas on how to get around this?

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

• How can see what processes makes my server slow?

  - by Steven

  All my websites on my server are extremely slow or not loading at all. Even server admin (Plesk) will not load some times. There's been no changes to the sites for the last coupple of months. How can I see what processes is making my server slow? My environment looks like this: Server: VPS running Linux 2.8.x OS: Centos 5 Manage interface: Plesk 9.x Memmory: 1024MB CPU: 2.2GHz My websites run on PHP and MySQL. I finally managed to telnet (Putty + SSH) in to my server. Running top did not show any processes using more than max 2% CPU and none were using exesive memmory. I also got a friend to install a program that checks the core files, and all seemed fine. So I'm leaning towards network issues or some other server malfunction. But I'm not able to find out what can be wrong. Here are some answers to Sean Kimball: I don't run mail services on my server yet There are noe specific bandwidth peaks. Prefork looks like this <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> Not sure what you mean with DNS question. But I think it's up and running. There are no processes running wild Where can I find avarage load? Telnet is disabled and I have to log in using SSH :)

  Read the article

< Previous Page | 856 857 858 859 860 861 862 863 864 865 866 867  | Next Page >