Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 87/114 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• Possible to IPSec VPN Tunnel Public IP Addresses?

  - by caleban

  A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

  Read the article

• Usb device not working properly on a Thinkpad T60

  - by Xavierjazz

  I have just started getting a message that a USB device is not working properly. This is on a new Thinkpad T60 running Windows XP Professional SP3. I have had all devices attached for about 10 days or so. When I go to device manager there is no sign of a problem: everything is working correctly. I am unable to find out which device it is. I searched this forum but the only reference I found was to older computers which may not be Usb2 capable. This is not my problem. Any ideas? Thanks. EDIT: I realized I had a harddrive attached but turned off. Although I could not track down any error messages except the balloon that came up, I have disconnected it and, so far, no messages. We'll see over the next day or two, but this may be the problem. Thanks EDIT: This has not solved the problem. I get the message that one of the USB devices has malfunctioned and it points to "USB root hub (2 ports)" and shows an unused port and an unknown device. However, when I check my device manager, it says that there are no problems, everything is working as it should. ?? EDIT: I now found the event log view and there are 2 types of error messages. They do not relate to the time that I get the balloon. 2 of the 3 are "Ati2mtag" errors and the third is "System Control Manager". Are these related to my problem, and the balloon just pops up randomly? EDIT: well, I'm still having the problem, and have narrowed it down to a malfunctioning device. Thanks to all.

  Read the article

• Alternatives to ntbackup

  - by Chris J

  Is anyone aware of any good (for a given value of "good") alternatives to ntbackup? There's a few quirks with ntbackup that I still find odd, and occasionally (and for no obvious reason) ntbackup just doesn't back up - usually complaining about that the wrong tape's inserted even though it's been told to just use the tape that's in the drive regardless. I've experiemented with cygwin's tar and cpio and Win32 ports of these utilities, but I've not had any luck getting them to see the tape device (so if someone does use these utilities to write to a tape device, also be interested to know how). Essentially all I'm looking for is a reliable program that I can tell to back-up a list of locations to the tape, and not to care about anything like formatting tapes, or sticking volume labels on them (and conversely then makes it fairly straightforward to restore off as well). On the flip-side, I don't want something that will attempt to manage our tapes. Don't get me wrong here -- ntbackup can do the job, but its quirks are making look at possible alternatives. Any suggestions? If it's open source, even better.

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Correct way to set up office network - 8 workstations, a file server and a staging server

  - by naunu

  Our office had this old school windows 2003 domain setup, our server caught fire, and now we are looking to do it right from scratch. Here is what we need: 5 PC and 3 Mac workstations for web development, they will each have WAMP/MAMP setup on them, managed by their developers. We will have a file server for assets, and a LAMP server with an external IP for staging. Here is what we have to work with: 5 IP addresses, brand new PC file server with windows 2008 SE, D-Link DSS-16+ 16 port switch, belkin 5 port wireless router, cable modem with 4 ports. How I have it set up now (this is a temporary makeshift setup): Cable modem = LAMP server, wireless router Wireless router = Switch = All of the workstations and file server (setup as a workgroup). We have noticed our internet is very slow with us all plugged in to the switch, and the switch plugged in to the router. I am not positive, but I think it is because our router does not have NAT. We are also having problems with the MACs connection to the network drive - it keeps disconnecting. I want this done right, and we have a ~$600 budget to buy anything else we need. Does anybody have any advice for me? Should I set up a domain or workgroup?

  Read the article

• another "SSH connect to host github.com port 22: Bad file number"

  - by Mariusz

  Hello. I have a problem with my first-time ssh connection. Yes, I've already done yours guides, already tried your "Dealing with firewalls and proxies" article and the problem is still occuring. I am using Win7 32bit, Windows Firewall is disabled, haven't any third-party firewalls, ESET Nod32 Antivirus is not blocking any ports, I am not using any PROXY (neither local proxy) . Here goes the logs: Ordinary SSH connection try C:\Users\Mariusz>ssh -vvv [email protected] OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug2: ssh_connect: needpriv 0 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: connect to address 207.97.227.239 port 22: Not owner ssh: connect to host github.com port 22: Bad file number NCAT connection try C:\Users\Mariusz>ncat github.com 22 Strange connect error from 207.97.227.239 (10013): No error 10013 = WSAEACCES I think that method called "smart-http-support" won't be usable for me because I haven't created repo yet. I have just GIT INIT locally, and finished at step GIT PUSH, which returns the same: ssh: connect to host github.com port 22: Bad file number fatal: The remote end hung up unexpectedly corkscrew method (first article from yours guide) . While PUTTYing (with pageant in bg), after inputing login - an error is occuring (MessageBox): Disconnected: No supported authentication methods available And in terminal such message is printing out: Server refused our key Key I have generated correctly, using ssh-keygen. I tried not method by editing ~/.ssh/config yet because I had thought that because I haven't PUSHed anything to my remote repo so I won't be able to CLONE anything. Method called ssh-forwarding is not for my, cause it "requires access to an external ssh server" and I haven't any at this time. What else could I do? Thanks in advance for any help. Mariusz.

  Read the article

• Using 1and1.com Servers, SMTP Mail is Limited - Local XAMPP Server Works As Expected

  - by nicorellius

  I'm starting to not like 1and1.com that much. I've used them for years, but mainly for simple sites without much need for configuration. I know there are better hosting companies out and I may go seeking them. The problem here is that on my Local XAMPP server (sitting on a network with Comcast ISP), I have a PHP script that uses PEAR::Mail to send mail using MIME. The script works find locally with either smtp.1and1.com and corresponding credentials and smtp.gmail.com with corresponding credentials, using appropriate ports, etc. 1and1 tells me that I have to change the MX record on the domain where this script runs in order to make this work. This doesn't make sense to me. Now I'm pretty new to all this, but how is it that this is the case? Why can my local server work just fine, out of the box, but their servers not? I have asked them these questions, but they are very vague and I cannot get any good answers from them. Versions: PEAR Version: 1.5.0 PHP Version: 4.4.9 Zend Engine Version: 1.3.0 My apologies in advance for my ignorance. Thanks for the help in advance.

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Remote Desktop *from* Windows 2008 R2 Server

  - by freefaller

  Summary: how do I create an RDC connection from a Windows 2008 server to another server? Our client will only allow us to connect to their server via a static IP address (which is fair enough), but unfortunately as we're a very small company we don't have one in the office. As a work around, we had the connection working through our old Windows 2003 server (dynamic-cloud from 1and1). .. however we have just rebuilt the server to run under Windows 2008 R2 (don't ask, but it was necessary), and now I simply cannot get the connection working. I have added an "Outbound Rule" to Windows Firewall with Advanced Security (TCP, All local ports, 3389 remote port - I have also tried the other way around). I have added a packet filter IP security rule with the same details. The 1and1 firewall rules (through their online control panel) allows for 3389 TCP and UDP. But it is simply not connecting (yes, the server is definitely on and able to accept connections) with the general error of... Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Is there anything obvious I've missed - or something I can use to find out where the request is being blocked? The new server is using the exact same IP address as before, so I don't believe that would be an issue. Unless it's trying to use an IPv6 address rather than the old IPv4 address that it was before? I apologise that I am not a network person by trade, but I know more than anybody else in my office!!

  Read the article

• Linux Tuning for High Traffic JBoss Server with LDAP Binds

  - by Levi Stanley

  I'm configuring a high traffic Linux server (RedHat) and running into a limit I haven't been able to track down. I need to be able to handle sustained 300 requests per second throughput using Nginx and JBoss. The point of this server is to run checks on a user's account when that user signs in. Each request goes through Nginx to JBoss (specifically Torquebox with JBoss A7 with a Sinatra app) and then makes an LDAP request to bind that user and retrieve several attributes. It is during the bind that these errors occur. I'm able to reproduce this going directly to JBoss, so that rules out Nginx at least. I get a variety of error messages, though oddly JBoss stopped writing to the log file recently. It used to report errors about creating native threads. Now I just see "java.net.SocketException: Connection reset" and "org.apache.http.conn.HttpHostConnectException: Connection to http://my.awesome.server:8080 refused" as responses in jmeter. To the best of my knowledge, I have plenty of available file handles, processes, sockets, and ports, yet the issue persists. Unfortunately, I have very little experience tuning servers. I've found a couple useful documents - Ipsysctl tutorial 1.0.4 and Linux Tuning - but those documents are a bit over my head (and just entering the the configuration described in Linux Tuning doesn't fix my issue. Here are the configuration changes I've tried (webproxy is the user that runs Nginx and JBoss): /etc/security/limits.conf webproxy soft nofile 65536 webproxy hard nofile 65536 webproxy soft nproc 65536 webproxy hard nproc 65536 root soft nofile 65536 root hard nofile 65536 root soft nproc 65536 root hard nofile 65536 First attempt /etc/sysctl.conf sysctl net.core.somaxconn = 8192 sysctl net.ipv4.ip_local_port_range = 32768 65535 sysctl net.ipv4.tcp_fin_timeout = 15 sysctl net.ipv4.tcp_keepalive_time = 1800 sysctl net.ipv4.tcp_keepalive_intvl = 35 sysctl net.ipv4.tcp_tw_recycle = 1 sysctl net.ipv4.tcp_tw_reuse = 1 Second attempt /etc/sysctl.conf net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 net.core.netdev_max_backlog = 30000 net.ipv4.tcp_congestion_control=htcp net.ipv4.tcp_mtu_probing=1 Any ideas what might be happening here? Or better yet, are there some good documentation resources designed for beginners?

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• How to get multipath working for Ubuntu Server 12.04

  - by mlampi

  I'm working on a project which aims to make use of Ubuntu servers running on enterprise class hardware. In our case that means IBM HS23E blade servers, QLogic 4GB fibre channel extension cards and quite old IBM DS4500 disk array with two controllers. At the moment we have fibre channel as only boot option and Ubuntu Server 12.04 installed just fine and is able to boot without multipath. I'm not a linux professional myself but in our team we have people who will understand the technical stuff. Don't let my post confuse :) The current situation is that we have only one fibre channel connection to a single disk array controller. Real life case would be of course quite different. At minimum we should have two fibre channel ports connected to two different switches and two different controllers. However, we have no idea how to set up multipath tool. Is the DM-MPIO the right software? At minimum we should be able to boot when multiple connections are available and achieve fault tolerance when any of them should be down. Since the disk array is not the latest hardware, I managed to find RDAC driver sources only for 2.6.x kernel. And we have 3.2.x. Another issue is to build a multipath.conf. The said driver sources are from IBM support and the QLogic drivers provided to Ubuntu installer are from Ubuntu site. It seems that RHEL and SLES would have near out of the box support but that is not an option for our project. Actual questions: - What is the recommended software tool for multipath for Ubuntu Server 12.04? - Is there available pre-made configurations or templates? Does it require disk array / controller specific settings or do a more generic config work? - Do you have expriences on similar setup and like to share the knowledge? I'll provide you with any additional information you might require. Thanks in advance.

  Read the article

• Passive FTP Server Port Configuration Troubles Win2003

  - by Chris

  Win2003 Ports 20 & 21 are open IIS6 - Direct Metabase Edit enabled Configured FTP service passive range to 5500-5550 5500-5550 added to windows firewall iisreset and double checked by restarting ftp service nothing has changed, when I connect and enter passive, it still hangs when ever I try to LIST or transfer files. Active is just as useless. Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Users\user>ftp ftp> open x.x.x.x Connected to x.x.x.x. 220-Microsoft FTP Service xxxxxxxxxxxxxxxxxx 220 xxxxxxxxxxxxxxxxxx User (x.x.x.x:(none)): user 331 Password required for user. Password: 230-YOUR ACTIVITY IS BEING RECORDED TO THE FULLEST EXTENT 230 User user logged in. ftp> QUOTE PASV 227 Entering Passive Mode (82,19,25,134,21,124) ftp> ls 200 PORT command successful. 150 Opening ASCII mode data connection for file list. and it hangs.. Now I can see from microsooft documentation that on newer windows releases, additional steps such as these are suggested, but they dont work on 2003... netsh advfirewall firewall add rule name=”FTP Service” action=allow service=ftpsvc protocol=TCP dir=in netsh advfirewall set global StatefulFTP disable is there anything I am missing, what is this StatefulFTP malarkey at the end EDIT I can connect and transfer binary files using WinSCP client - Therefore the problem must be with my ftp commands no? Can anyone see anything wrong with my windows ftp client example? why would it hang on ls, i tried QUOTE LIST as well, and that just hangs, and the windows ftp client doesnt work in active, it hangs if I try to go "binary" then put - This worked before I added 5500-5550 on the router. I have since added this range to the router but no difference to the windows ftp client.

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• Router recommendation to virtualize 800 IPs

  - by delerious010

  I've recently been looking at getting some new load balancers for our environment as we are expecting to double our client base in the next 12 months. Currently we have 400 public IPS serving 800 clusters ( 2 clusters / IP due to ports ) on Coyote Point Balancers, and distributing connections to 3 web servers serving about 6GBytes outgoing, 2Gbytes in per day. If we double, this would be about 800 IPs, possibly 1600 clusters, and about 6 servers per cluster ( for a total of 9600 so called "real servers" using Barracuda's lingo ). Due to the amount of clusters, most solutions I've looked at ( Coyote, Barracuda, Loadbalancer.org ) seem to be unsure whether they'll be able to handle our planned growth, mostly due to health checks performed on the servers ... which makes total sense when you think of it. So the fine folk at loadbalancer.org recommended that we may be better off offload the 400-800 public IPs, which we require for SSL eCommerce solutions, over to a forward facing router. From that point on, the router could do some mangling to route EXT_IP:443 to INT_IP:INT_PORT which would then allow us to reduce the Load Balancer configuration to 1 or 2 clusters, thus resolving the health check problem. Does this idea make sense to yall ? Or would you have other recommendations to make ? Secondly, what router would you recommend for such an undertaking ? I'd be looking at something that has some form of failover mechanism built in. On a totally unrelated note, I've got to admit that I'm extremely pleased with the responses I got from loadbalancer.org. Their responses to my inquiries were surprisingly helpful ( i.e. I didn't feel as if I was taking to a sales guy trying to push something ). ( No I don't work for them, and sadly nor are they sending me free gear ).

  Read the article

• What's wrong with my VirtualHost?

  - by johnlai2004

  I have the following VirtualHost // filename: /etc/apache2/sites-available/ccbbbcc <VirtualHost 1.1.1.1:80> ServerAdmin [email protected] ServerName ccbbbcc.com ServerAlias www.ccbbbcc.com DocumentRoot /srv/www/ccbbbcc/production/public_html/ ErrorLog /srv/www/ccbbbcc/production/logs/error.log CustomLog /srv/www/ccbbbcc/production/logs/access.log combined </VirtualHost> And then I also have //filename: /etc/apache2/sites-available/default <VirtualHost 1.1.1.1:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> blah blah blah How come when I type into my browser http://1.1.1.1, it takes me to http://ccbbbcc.com ? Even when I point new urls to the IP 1.1.1.1, webpages serve from http://ccbbbcc.com. Why is the ccbbbcc.com overriding all my other virtual hosts? Why am I unable to serve pages from /var/www directory? I've made sure to use a2ensite and to restart apache. This is what my /etc/apache2/ports.conf looks like NameVirtualHost 1.1.1.1:80 Listen 80 Listen 443

  Read the article

• Running docker in VPC and accessing container from another VPC machine

  - by Bogdan Gaza

  I'm having issues while running docker in AWS VPC. Here is my setup: I've got two machines running in VPC: 10.0.100.150 10.0.100.151 both having an elastic IPs assigned to them, both running in the same internet enabled subnet. Let's say I'm running a web server that serves static files in a container on the 10.0.100.150 machine the container: IP: 172.17.0.2 port 8111 is forwarded on the 8111 port on the machine. I'm trying to access the static files from my local machine (or another non-VPC machine also tried an EC2 instance not running in the VPC) and it work flawlessly. If I try to access the files from the other machine (10.0.100.151) it hangs. I'm using wget to pull the files. Tried to debug it with tcpdump and ngrep and that I have seen is that the request reaches the container. If I ngrep on the host machine I see the requests going in but no response going back. If I ngrep on the container I see the requests going in and the response going back. I've tried multiple iptables setups (with postrouting enabled, with manually forwarding ports etc) but no success. Help in any way - even debugging directions would be much appreciated. Thanks!

  Read the article

• IPTables configuration for Localhost

  - by Gabe Mc

  I have a problem in connecting a JIRA instance running on a cloud server to an instance of MySQL running on the same box. I have configured it previously using quite a few iptables rules, but it seems overly broad/terribly inprecise. I want access to several of localhosts ports from the local machine, but deny it from all other accounts. Currently, my /etc/iptables.rules file looks like: *filter :INPUT DROP [223:17779] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [10161:1120819] # SSH Access -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT # Apache2 Access for connecting to Tomcat on port 8080 -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT # MySQL -I INPUT -i lo -p tcp -m tcp --dport mysql -j ACCEPT COMMIT However, this doesn't allow me to log in when I try logging in; it just hangs on: #> mysql -u root -p -h 127.0.0.1 The Tomcat servlet container starts throwing all kinds of exceptions, as well. This is a more general problem, as I need to enable things like accessing the shutdown port for the Tomcat container, but I need to at least get the MySQL part ironed out first, without the ugliness I was originally trying. Thanks.

  Read the article

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Dos/ Flood Lag even though Port not Saturated

  - by Asad Moeen

  My GameServers had been under some UDP Floods due to which they generated outputs to the attacker which gave the GameServers some huge lags. Thanks to friends at ServerFault that upon different kind of testing, I was able to successfully block the attack. My question is actually something else but it is important to know how the GameServers reacted to the attack and if the machine kept stable or not: 300kb/s Input would cause GameServer to generate 2mb/s Output. So as the Input Rate kept increasing, output rate would reach so high that it would no longer be possible for the GameServer to control it and hence it would give a huge Lag until the attack is stopped. Usually the game server starts to lag when it sends out something greater than 5mb/s and under that is controllable. Theoretically, I was able to receive a 60mb/s output from my GameServer on inputting 10mb/s. Its just the way the GameServer works if not protected. Now on some of my machines, only the GameServer under attack lagged and although the server was generating 60mb/s output, rest of the gameservers on other ports would run fine without lags on the same machine. But there was another machine which also runs on a 100 MBPS Network port, even 1 mbps input ( and ZERO output because attack is blocked ) even on an unused port would give a constant yellow line ( on the Lag-o-Meter ) to all the clients on all GameServers indicating lag because that line is actually blue under normal conditions. It would remain the same even on 50mbps or 900mbps input. I tried contacting the host about it because I believe its the way their Network is bridged, but they can't help me about it. Anyone else knowing about such issues because if 900mbps input does not Saturate the port, how can 1mbps input lag the servers although port is not saturated and enough bandwidth is available?

  Read the article

• Distorted Sound

  - by BCable

  I have my laptop hooked up to my receiver for sound output. I hear a hissing/crackling background sound that is really loud and hard to just ignore (but possible). When my 360 is connected, the sound comes out perfect, so it's just with this laptop. Previously, I thought it was just my laptop and just submissively just let it slide. I just bought a brand new laptop though and it's doing the same thing. I have found out more information now that I know it's not my laptop. I have used this laptop in similar environments where it worked just fine (different speakers). I have bought a new cable to connect to my receiver and it did nothing (headphone jack to RCA). I tried different ports on the receiver (Video 1-3) and it always happens. I have discovered that the sound goes away if I unplug my laptop (so it's running on battery). Because of the last one, I tried plugging my laptop into a different outlet across the room and it's STILL doing it. Doesn't matter if I boot to Linux or Windows, yet my phone (Android G1) doesn't cause this sound using the exact same cable. Any ideas? I'm out of them! Thanks!

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >