Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 89/101 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• How to connect a USB GDI printer to Linux over a D-Link print server?

  - by jpe

  The setup is the following: +------------+ +-----------------+ +---------+ | HP LJ P1005|--USB--| D-Link DPR-1020 |---LAN---| PC Linux| +------------+ +-----------------+ + +---------+ | +------------+ +--| PC Windows | +------------+ HP LJ P1005 is one of those GDI printers that requires the printer driver to do most of the work for it and therefore is a bit "special". D-Link DPR-1020 is a print server with an Ethernet and an USB port that actually supports printing to challenged (read GDI) printers using a utility called PS-Link. What the utility does is basically mirror a USB port over the network to the print server so that the printer driver and the printer both are happy to talk to each other. The PC-s are notebooks that come and go, i.e. are not there all the time. Is there an equivalent of the D-Link PS-Link utility for Linux that could mirror a USB port over the network for a Linux host? And can the solution be used with D-Link DPR-1020? If not then I basically wasted the money buying the print server because the goal was to share a small printer among a couple of users with diverse operating systems in an office. The print server specs say that it supports Linux and LJ P1005, but the Catch 22 appears to be the solution used for GDI printers... It should be noted that it is possible to print from Linux to LJ P1005 directly over USB. This far sharing involved reconnecting the USB cable to appropriate computer to print. Now one of the desks is separated, so the cable does not work. Searching the net did not yield anything useful. Please do not suggest solutions involving a Windows machine (either virtual or not), my question is whether a solution only involving a Linux machine exists.

  Read the article

• EC2 instance is blocking all outbound connections, how to diagnose/fix?

  - by Fraggle

  My EC2 instance is blocking all outbound connections. wget http://www.google.com ==> Hangs ping google.com ==>hangs ssh user@anyserver ==>hangs I ran : sudo iptables -F to eliminate all rules to no avail AWS Management console shows Security Group for that instance has Inbound rule allowing ssh and port 80. Can't find anything about Outbound rules there. Rebooted instance, no change. If anyone knows how to diagnose or fix, please help. Adding info: [ec2-user@ip-10-112-62-73 ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3D:06:31:BB inet addr:10.112.62.73 Bcast:10.112.63.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3dff:fe06:31bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1933 errors:0 dropped:0 overruns:0 frame:0 TX packets:1764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164075 (160.2 KiB) TX bytes:343256 (335.2 KiB) Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:672 (672.0 b) TX bytes:672 (672.0 b) [ec2-user@ip-10-112-62-73 ~]$ ip route show 10.112.62.0/23 dev eth0 proto kernel scope link src 10.112.62.73 default via 10.112.62.1 dev eth0

  Read the article

• Get Internal IP Address From DHCP Hostname

  - by ell

  I would like to try and get an internal ip address of one of the computers on my network. The reason for this is I have a little home server box downstairs but every time I want to SSH into it I have to open my router configuration and go on the DHCP client table and look at the IP address. For example I would like to be able to go ssh ell-sever instead of ssh 192.168.1.105 or whatever it happens to be. My network configuration is like so: Router downstairs that is connected to the Internet and is running a DHCP server My server computer (ell-server) is a headless pc connected to the router via ethernet cable. Running Ubuntu 11.04 Server Edition My laptop upstairs (ell-laptop) that is running Ubuntu 11.10 Desktop Edition connected wirelessly Other (irrelevant) computers - 2 x Windows XP, 1 x Xubuntu - all connected with cables. (It seemed to me the method of connection isn't useful information but I put it in anyway - just in case. If I have missed any information please tell me) Do I have to run a DNS server on one of my computers? If so which one? And does that mean I will have to run a DDNS client on each computer? Thanks in advance, ell.

  Read the article

• Windows 7 fails to connect to the internet a few minutes after startup

  - by SageTheGreat

  Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

  Read the article

• Recommended open-source firmware for ASUS RT-N16

  - by MasterF

  I have recently acquired an ASUS RT-N16 router. My original plan for it was to install Tomato on it. However, after checking their website i found out that the firmware was not updated in the last 2 years. There seem to be a few updated mods but none of them really seemed mature/stable/well-documented. I would like to know what other people recommend as open-source firmware for this router. I know the answers will probably be subjective; so i will give a bit of background on my needs: for now i will only use the Wi-Fi on an Android phone the connection will not be shared with anyone (so QOS is optional) i want a stable (wired) connection on my PC (for online gaming etc.) i want the (wired) download/upload speeds to be as close as possible to those achieved by directly plugging the Ethernet cable to the PC's network card; i have a 100 Mbps connection my ISP uses PPPOE my technical level: i am a software developer and i have good knowledge of bash scripting, but no experience with networking Also, i know that i could probably just use the stock firmware (and maybe will use it for a while), but i'm interested in trying an open-source version (for more features, flexibility, as a learning exercise etc.)

  Read the article

• Connection problems via Wifi (multiple devices)

  - by Kelvin Farrell

  I'm having connection issues with my router (Linksys WRT610N) at home. There are a number of things that are happening (may be more, this is just what I've mainly noticed)... 1) Using my laptop (Macbook Pro OSX Lion), I am unable to complete any operations with my external FTP server, hosted with FatCow. I can connect to it, navigate through all the files, but when I try to edit/delete/add a file the operation times out. EVERY time. I've used two other Wifi connection on my laptop and neither have this issue. 2) I am unable to upload photos/videos to Facebook or Twitter using my phone (Samsung Galaxy S2) or my tablet (HP Touchpad - CM9). Neither am I able to upload files to Dropbox via either of the devices. Same thing happens in all situations; the upload will begin and it will just hang on 0% forever. After about 10 mins I am always forced to disconnect the Wifi to stop the action. 3) My laptop is having slow internet speed, even though we are on 20mb broadband. Speedtests say I'm getting a good connection and my Ping is good, but when using streaming services like Spotify, it takes forever to load a page and frequently stops to buffer whilst playing a song. Don't know if it's worth mentioning but I have no issues with my XBox (Ethernet), AppleTV (Wifi) or my girlfrield's phone (Nokia Lumia 800 - WP7.5) on the network. I'd really appreciate any help. This is driving me insane and is really affecting both my working and leisure use of the internet.

  Read the article

• Iptables QUEUE Target and Snort

  - by bradlis7

  I'm trying to set up a firewall with support for snort, and it is dropping all of my packets when I add the QUEUE target. I've made it like this, but the QUEUE target is not allowing the packets to be processed any further: -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -j QUEUE -A INPUT -j ACCEPT # It's not allowing anything past QUEUE, as you can see below in the count. > iptables -I INPUT -nv pkts bytes target prot opt in out source destination 6707 395K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 933 138K QUEUE all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 I'm eventually going to change it to forward, but I'm just trying to get it working for now. I start snort like so: snort -Q -D -c /etc/snort/snort.conf EDIT: More Information When I run it, it still sees the packets without having an iptables QUEUE target rule, but when I add a QUEUE target, it starts losing all of my packets. # snort -Qc /etc/snort/snort.conf -N -A console Enabling inline operation Running in IDS mode --== Initializing Snort ==-- Initializing Output Plugins! Initializing Preprocessors! Initializing Plug-ins! Parsing Rules file "/etc/snort/snort.conf" ## === CUT === *** *** interface device lookup found: bond0 *** Initializing Network Interface bond0 Decoding Ethernet on interface bond0 ## === CUT === Not Using PCAP_FRAMES So, it says inline, but the it says it's using bond0. Inline should not require an interface, right?

  Read the article

• What are the frequencies of current in computers' external peripheral cables and internal buses?

  - by Tim

  From Wikipedia, three different cases of current frequency are discussed along with the types of cables that are suitable for them: An Extra Ordinary electrical cables suffice to carry low frequency AC, such as mains power, which reverses direction 100 to 120 times per second (cycling 50 to 60 times per second). However, they cannot be used to carry currents in the radio frequency range or higher, which reverse direction millions to billions of times per second, because the energy tends to radiate off the cable as radio waves, causing power losses. Radio frequency currents also tend to reflect from discontinuities in the cable such as connectors, and travel back down the cable toward the source. These reflections act as bottlenecks, preventing the power from reaching the destination. Transmission lines use specialized construction such as precise conductor dimensions and spacing, and impedance matching, to carry electromagnetic signals with minimal reflections and power losses. Types of transmission line include ladder line, coaxial cable, dielectric slabs, stripline, optical fiber, and waveguides. The higher the frequency, the shorter are the waves in a transmission medium. Transmission lines must be used when the frequency is high enough that the wavelength of the waves begins to approach the length of the cable used. To conduct energy at frequencies above the radio range, such as millimeter waves, infrared, and light, the waves become much smaller than the dimensions of the structures used to guide them, so transmission line techniques become inadequate and the methods of optics are used. I wonder what the frequencies are for the currents in computers' external peripheral cables, such as Ethernet cable, USB cable, and in computers' internal buses? Are the cables also made specially for the frequencies? Thanks!

  Read the article

• iptables captive portal remove user

  - by Burgos

  I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

  Read the article

• Debian: What are these files in /sys/devices/pci0000:00/ for?

  - by muhuk

  I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• How to Load Balance 2 Internet Connections on a Windows 7 machine?

  - by Jimmy Chandra

  It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• Why Wireshark does not recognize this HTTP response?

  - by Alois Mahdal

  I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• MacBook Pro and Backtrack 5R1 Configuration

  - by user119346

  I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

  Read the article

• Cisco Access switch is dropping large amount of end points

  - by user135458

  This afternoon, with no changes to the network, a switch suddenly started dropping off lots of connections. These connections would come back up a few minutes later, then another area connected to the switch would drop off. This is an older 4006 chassis switch which could in and of itself be a problem but I'm looking to see what else you all would look for in trying to find a root cause. Switch is connected via ports 1/1 and 1/2 in an etherchannel to a VSS core 1/1/42 and 2/1/42. Both sides are up and working however the CPU on the switch will spike up to 99% and that's when CRC errors start to hit the VSS core on one of those interfaces and end points start dropping off. We tried new transceivers and SFP's on each side of the link, same result. When we tried swapping the fiber patch cables on the access switch the CRC errors did not follow the fiber cables they stayed with port 1/2 on the access switch. So port 1/2 on the supervisor module looks like the culprit. We actually tried to create a new member of the ethernet channel by taking a fiber media converter to cat5 and make that a member of the port-channel but when we plugged it in you couldn't even reach the switch. I'm guessing that's unrelated and a problem with the media converter. As of right now we have left it in a state of only one fiber cable running to one side of the VSS core (1/1 Access Switch -- 2/1/42). I've sent some info into TAC and they are looking into the situation but does anyone else have any commands I could run or some troubleshooting I could look into in the meantime?

  Read the article

• Is there a realiable way to troubleshoot wake up from sleep in Windows?

  - by Borek

  Is there a reliable way to troubleshoot laptop wakes? I've seen "heuristics" posted here and there but isn't there really a simple and deterministic way to tell what's causing a problem? Specifically, my laptop wakes up about every hour for about 2 minutes. Exported event log entries are here: http://www.mediafire.com/?abcqb00v5wyo6pj. I've tried: powercfg -devicequery wake_armed Empty result set. Scheduled tasks - the main ones are not scheduled to run every hour. When go through a long list of all possible tasks, there are some that are set to be triggered every hour (e.g., MS "RacTask" whatever it is). But when I go to power options, Advanced settings, Sleep, Allow wake timers it is set to "Disable". Also, the specific task is not set to wake the computer if necessary. Power options for my Ethernet card don't enable it to wake the computer - the cable is disconnected anyway. There are no other HW devices attached - no USB disks, no keyboards / mice etc. I am really clueless and quite unhappy that it's so hard to troubleshoot this situation.

  Read the article

• Internet Sharing on Lion breaks my routing table

  - by seaders

  When in the office, I'm connected to a 192.168.1.0/24 network. When Internet Sharing is off, when I run netstat -nr the first entry shows default 192.168.1.254 UGSc 10 62 en0 If I turn Internet sharing on, it shows default link#5 UCS 2 0 en1 This is obviously incorrect and breaks all connectivity of my machine. en1 is my wireless, whereas en0 is my ethernet. If I then disable Internet Sharing, it even deletes that incorrect route, so I'm left with no default route at all. Currently I have one script that I run when I share, or after, when I disable that does route delete default route add default 192.168.1.254 That fixes everything, but I'd love to know what's actually making this happen and how to properly fix it. And just to say that at some point a few months ago, this was working absolutely perfectly, with no hitches, then one day when I brought the laptop home, I couldn't disable the internet sharing, so I couldn't connect to my home wifi. I eventually had to restart the machine and since then this problem has been happening. Any help would be greatly appreciated, thank you.

  Read the article

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Is there any way to force my Linux box to always boot up with a self-assigned IP address?

  - by Jeremy Friesner

  This is perhaps an unusual request: I'm trying to get a Debian Linux box to always give itself a self-assigned IP address (i.e. 169.254.x.y) on boot. In particular, I want it to do that even when there is a DHCP server present on the LAN. That is, it should not request an IP address from the DHCP server. From what I can see in the "man interfaces" text, there is an option for "manual", and an option for "dhcp". Manual assignment won't do, since I need multiple boxes to work on the same LAN without requiring any manual configuration... and "dhcp" does what I want, but only if there is no DHCP server on the LAN. (A requirement is that the functionality of these boxes should not be affected by the presence or absence of a DHCP server). Is there a trick that I can use to get this behavior? EDIT: By "no manual configuration", I mean that I should be able to take this box (headless) to any LAN anywhere, plug in the Ethernet cable, and have it do its thing. I shouldn't have to ssh to the box and edit files to get it working each time it is moved to a different LAN.

  Read the article

• How do you initialize networking on a new Xen guest VM?

  - by Marten Veldthuis

  We have a Citrix XenServer setup, and while I personally lean more towards Dev than Ops, I've got an issue that's been bugging me. When you provision a new (Linux/Ubuntu) guest, how do you get it to have the correct IP-address? I'd want my application servers to exist in the range of 10.20.0.0/24, preferably being .1, .2, etc, so I can keep my sanity. I guess that the actual IP-address is something set in Linux itself, and Xen can't touch that, but then what's the best practice for getting it done? If you set up DHCP, don't you just move the problem to getting the adapters the "correct" MAC-addresses? Do you just have to hardcode a large table of MAC-addresses to IP-addresses, and then provision new guests always with the correct MAC-address on the virtual ethernet adapter? What we currently do is have an image of a "app server" that we boot up a new instance of, and then finalize it (with a script) that (among other things) modifies the /etc/networking/interface file to give it the correct IP. But that feels dirty to me, and I feel like surely there must a better way. Please enlighten me?

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• Tunneling a public IP to a remote machine

  - by Jim Paris

  I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

  Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >