Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 92/101 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

  - by Mark Pim

  I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

  Read the article

• Assigning IPs to OpenVZ containers

  - by Vojtech

  I have recently bought myself a physical server and I am trying to create containers which would have their IPs. The physical machine has both IPv4 and IPv6 addresses. I have accessible another IPv4 and some other IPv6 addresses which I would like to assign to the container. I managed to assign the addresses as follows: # vzctl set 101 --ipadd 144.76.195.252 --save I can ping to the machine from the physical machine, but not from the outside world. This also applies to the IPv6 I assigned as well. This is ifconfig of the physical machine: eth0 Link encap:Ethernet HWaddr d4:3d:7e:ec:e0:04 inet addr:144.76.195.232 Bcast:144.76.195.255 Mask:255.255.255.224 inet6 addr: 2a01:4f8:200:71e7::2/64 Scope:Global inet6 addr: fe80::d63d:7eff:feec:e004/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:217895 errors:0 dropped:0 overruns:0 frame:0 TX packets:16779 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:322481419 (307.5 MiB) TX bytes:1672628 (1.5 MiB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1108 (1.0 KiB) TX bytes:1108 (1.0 KiB) This is ifconfig of the OpenVZ container: # ifconfig venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 inet6 addr: 2a01:4f8:200:71e7::3/64 Scope:Global UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1108 (1.0 KiB) TX bytes:1108 (1.0 KiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:144.76.195.252 P-t-P:144.76.195.252 Bcast:144.76.195.252 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 What do I need to do to have the container accessible from the outside world? What could I have forgotten? Thanks.

  Read the article

• Motorola Surfboard SB6121 modem conected to 2WIREi38HG wireless router but there's no internet access

  - by Jessica

  I have just switched to Comcast cable internet from AT&T Uverse and I was hoping to use the 2WIRE wireless router with the new Surfboard modem so I can have wireless access. I messed around with some settings and got it working for my laptop (I'm not terribly well versed in computer stuff; I think it was mostly luck) for about a week. The other day I tried to get online and there was no internet connection. I restarted the equipment with no success and then plugged the modem directly into the laptop. This worked, so I knew there was no outage. I connected the ethernet cord to the router and a second cord to my laptop and that worked, too. But when I tried again just with the wireless the laptop connects to the router, but doesn't recognize it or find an internet connection. I tried to go to http://gateway.2Wire.net to fiddle with the settings, but all I get is a Server Not Found page. I tried to check the ip address but this is really kind of over my head and I get different things checking it while plugged into only the modem vs when I plug into the router. Can anyone help? The frustrating thing is that I had it working for awhile, so I know it can do it!

  Read the article

• Periodic internet connection drops

  - by user9647

  My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

  Read the article

• Help with routing table

  - by user68752

  I have tried to find the answer to my question but not really found a clean and easy solution. I have a box (Ubuntu headless 10.04.1 server, with one Ethernet port) on LAN behind a router (running m0n0wall), that I have successfully installed a PPTP device (ppp0) on, this is working flawlessly (following this link) The thing is I want this box to route all it's internet traffic through the VPN tunnel (ppp0 device) but also being able to access the local LAN on 192.168.1.* subnet. I've succeeded a bit with this, but my problem right now is that I have port forwards (e.g. SSH) done in the m0n0wall pointing to this specific box which forces me to do "add routes" to all boxes that want to access this machine through this specific port. For instance a machine with ip xyz.xyz.xyz.xyz needs to have a static route setup in the routing table on the box to be able to access the box. This is the result of route -n xxx.xxx.137.2 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0 xxx.xxx.137.2 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 yyy.yyy.0.0 192.168.1.1 255.255.0.0 UG 0 0 0 eth0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 Where xxx is the IPs provided from VPN server. yyy.yyy.0.0 is a net that i want to have access to the box, without this I can't access the box from outside the LAN (via port-forwards done in router software, m0n0wall) is there away round this ugly solution?

  Read the article

• Intel Motherboard Lightning Victim Dies Hard

  - by Stetson RDT

  Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

  Read the article

• DSL Connection drops

  - by user60024

  Ok, I just moved so I had to switch from Cable to DSL. I know very little about computers or internet connections and such, so I had AT&T come out to the new house to set up their highest speed. When they got here, they told me that I needed to downgrade to 3.5mbps because I was too far away. Well we did and everything was going great for two days until I started experiencing random disconnects which have been happening now for about 2 to 3 weeks. I am using a N300 Wireless Dual Band ADSL2+ Modem Router and my ethernet cable is hooked directly into my computer from it. I recently started to notice that it disconnects around 5:30 and 8:30, which may be because a lot of people are on their computers(?) and that it works perfectly fine, almost, all the time if I'm not playing a game. During this time, when I try to load up World of Warcraft the Internet light disappears and the DSL light begins blinking. (So maybe it's too much for the modem and it resets?) Other than that it is amazing, but I'd like to try and fix some of these problems. If you need more information, let me know on how to get it for you and what to do. Thanks for the help!

  Read the article

• RTL8188CE doesn't connect to any wifi access points

  - by Drakmail

  I'm using network manager to connect. Also, tryed iwconfig. Results are same. I even try to connect to open access point — results are same. More information: Drakmail@thinkpad-x220:~$ lspci | grep Network | grep -v Ethernet 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Drakmail@thinkpad-x220:~$ uname -a Linux thinkpad-x220 3.1.0 #1 SMP PREEMPT Wed Oct 26 02:19:49 UTC 2011 x86_64 Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz GenuineIntel GNU/Linux Drakmail@thinkpad-x220:~$ dmesg | tail -n 10 [ 846.901574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 906.812461] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 966.728810] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1026.639676] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1030.925574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin At this moment I try to connect to open wifi ap: [ 1031.252403] wlan0: direct probe to 00:24:8c:55:fa:ed (try 1/3) [ 1031.451943] wlan0: direct probe to 00:24:8c:55:fa:ed (try 2/3) [ 1031.651658] wlan0: direct probe to 00:24:8c:55:fa:ed (try 3/3) [ 1031.851354] wlan0: direct probe to 00:24:8c:55:fa:ed timed out [ 1086.544960] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin My distribution: Drakmail@thinkpad-x220:~$ cat /etc/*version AgiliaLinux release 8.0.0 (Sammy) (Something between Slackware and Archlinux). Also, I saw that wifi module to often trying to load a firmware file. Any ideas what it would be?

  Read the article

• How do I speed up and cache mmap file access over NFS on Linux?

  - by Zan Lynx

  The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• Static IP addressing issue in Ubuntu on BeagleBoneBlack Rev C

  - by Stringfellow

  I have my BBB configured to use a static IP address using the following in the file /etc/network/interfaces: allow-hotplug eth0 iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 network 192.168.0.0 This seems to work ok on boot, but when the ethernet cable is unplugged and then plugged back in, I lose the IP address. Any ideas what's going on here? Another weird symptom: If I boot the BBB with the network cable unplugged, but the switch it's plugged into off, I'll get my static IP. But, when I turn the switch on, I'll get a DHCP-assigned address. This is even though I have it configured with a static IP address. One last thing. If I ifdown etho, the interface will be gone when I do an ifconfig. If I wait a few seconds, though, and then re-run ifconfig, it will reappear, without an IP address. (Before I disabled IPv6, I used to get a IPv4 DHCP address in this case... weird). When that happens, I get a message like this in /var/log/messages: Apr 23 20:32:06 beaglebone kernel: [ 737.170172] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Apr 23 20:32:06 beaglebone kernel: [ 737.170304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Here's my uname -a: root@beaglebone:/etc# uname -a Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l GNU/Linux Any ideas what's going on here?

  Read the article

• Bypass network stack. Which options do we have? Pros and cons of each option [on hold]

  - by javapowered

  I'm writing trading application. I want to bypass network stack in Linux but I don't know how this can be done. I'm looking for complete list of options with pros and cons of each of them. The only option I know - is to buy solarflare network card which supports OpenOnLoad. What other options should I consider and what is pros and cons of each of them? Well the question is pretty simple - what is the best way to bypass network stack? upd: OpenOnload It achieves performance improvements in part by performing network processing at user-level, bypassing the OS kernel entirely on the data path. Intel DDIO to allow Intel® Ethernet Controllers and adapters to talk directly with the processor cache of the Intel® Xeon® processor E5. What's key difference between these techologies? Do they do roughly the same things? I much better like Intel DDIO because it's much easy to use, but OpenOnload required a lot of installation and tuning. If good OpenOnload application is much faster than good Intel DDIO application?

  Read the article

• How do i Setup a Mac OS X Server - NameServer behind an Airport Extreme?

  - by basilmir

  I have a Mac mini server i want to setup to host a couple of things. My setup is as follows: The WAN connection (static IP and ISP nameservers) goes into the wan port of the Airport Extreme. The Mac mini server is connected to one of the ethernet ports. The mac mini will host my domain something.com. My settings so far: Airport Express gets: 96.x.x.x as the external static IP from the ISP 174.y.y.y as the nameserver Mac mini server always gets a reserved DHCP IP from the Airport Express: 10.0.1.3 is the server's ip 10.0.1.1 as the dns (this ip is the airport express itself) My dns server has an A record pointing to ns.something.com and a PTR doing the reverse. I've already added my 96.x.x.x to point ns.something.com with my registrar as attached. NOW: Nobody seems to be able to access my ns.something.com to resolve any of my records. From a any computer in my network I CAN see my ns and everything works. The outside on the other hand does not... it's as if the airport extreme which "holds" the exterior 94.x.x.x address doesn't pass DNS along to my 10.0.1.3 ns server. I have the server managing the airport. Isn't this supposed to work?

  Read the article

• Transfer iptables rules to another server (almost) real time

  - by MrShunz

  I'm running 2 cPanel servers with ConfigServer Security & Firewall plugin. One of the functions of the plugin is to block via iptables (temporarily and/or permanently) IPs which fail various authentications (POP3/IMAP, SMTP, FTP, webmail, mod_security and such). Now, i'd like to push those IP blocks to the border router to drop packets as soon as possible (and doing so protecting the other machines on the network). Keep in mind that after N failed logins IP is blocked for 5 minutes, then re-allowed. If multiple bans occours in an hour IP is blocked permanently and should be unlocked "by hand". So I need a near realtime solution. What I'm looking for is a better way than firing some cronjobs both on cPanels and border router to: dump the rules to file transfer the file to border router (via scp/sftp) load the rules from the file in the border router I'm aware that I will need some scripts to parse and modify the rules as cPanels have one ethernet interface and some aliases while border router has two ehternet interfaces and some loopbacks. All machines involved use Linux. EDIT as per @pjmorse comment. The plugin consists of a bunch of perl and config files. The part I'm intrested in is a process which scans logfiles (lfd) and installs iptables rules (and sends an alert email). Fact is, it upgrades quite often (one or two times a week) and itself is 7000 lines of perl so I'm not comfortable on tampering with it.

  Read the article

• SQL Server: Network pauses after installing cheap SATA card: Is there a solution?

  - by samsmith

  At the risk of being assigned to the "bad DBA" club... I did something desperate, and may have to undo it. Problem: After installing a low cost eSATA board, my SQL Server is intermittently unresponsive (seemingly when there is a lot of IO to the eSATA drive). Questions: 1) Is there a solution to the intermittent unresponsiveness that allows me to keep the eSATA in place? 2) Whether or not (1==true): What is a decent, low cost way to add 1-3 TB storage to SQL for non-critical SQL DBs? Detail: Our SAN is full, and expanding it is costly and will take a month. I have a pressing need to add 1-3 TB for some development DBs (e.g. not mission critical; data loss is OK). As a bandaid, I threw a $20 eSATA PCI board in the Dell 1950 server, and attached an external 2TB eSATA drive. This seemed to work fine, but I notice that our production SQL DBs, and even remote desktop, now experience network "pauses" that they never did before (with both SQL client apps and remote desktop throwing "networking problem" errors). This SQL Server has lots of memory, and runs an instance of SQL 2005 (where all line of business apps reside) and an instance SQL 2008 (for development db's). SQL Server RAM has been appropriately configured, and this setup has run great for years. The server is: Dell 1950 Win2003 x64 14GB RAM PERC controller, 2 mirrored hd's internal Dell SAN over gbit ethernet, dual homed 2 PCIx slots (1 used by NIC for SAN, 1 now in use for eSATA board) Thank you for suggestions!

  Read the article

• Locate devices within a building

  - by ams0

  The situation: Our company is spread between two floors in a building. Every employee has a laptop (macbook Air or MacbookPro) and an iPhone. We have static DHCP mappings and DNS resolution so every mobile gets a name like employeeiphone.example.com, every macbook air gets a employeelaptop.example.com and every macbook pro gets a employeelaptop.example.com on the Ethernet interface (the wifi gets a dynamic IP from a small range dedicated for the purpose). We know each and every MAC address of phones and laptops, since we do DHCP static mapping (ISC DHCP server runs on linux). At each floor we have a Netgear stack of two switches, connected via 10GB fiber to each other. No VLANs so far. At every floor there are 4 Airport Extreme making a single SSID network with WPA2 authentication. The request: Our CTO wants to know who is present at which floor. My solution (so far): Every switch contains an table listing MAC address and originating port. On each switch stack, all the MAC addresses coming from the other floor are listed as coming on port 48 (the fiber link). So I came up with: 1) Get the table from each switch via SNMP 2) Filter out the ones associated with port 48 3) Grep dhcpd.conf, removing all entries not *laptop and not *iphone 4) Match the two lists for each switch, output in JSON or XML 5) present the results on a dashboard for all to see I wrote it in bash with a lot of awk and sed, it kinda works but I always have for some reason stale entries in the switch lookup tables, making it unreliable; some people may have put their laptop to sleep, their iphones drop connections after a while, if not woken up and so on..I searched left and right, we are prepared to spend a little on the project too (RFIDs?), does anybody do something similar? I can provide with the script if needed (although it's really specific to our switches and naming scheme). Thanks! p.s. perhaps is this a question for stackoverflow? please move if it so.

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Network Sniffing and Hubs

  - by Chris_K

  This will likely seem naive to the experts... but it has been on my mind lately. For years I've been using ntop and a cheap 4 port hub to sniff client networks to determine who's doing what -- and how much. Great way to see what's going on when they call and say "Geeze, the network seems really slow today." No need to bring in a managed switch (or access the existing one) and no need to configure spanning or mirroring. I just drop in the hub inline where I want to measure. Lately I noticed it is just about impossible to buy a real honest-to-goodness hub anymore. While looking for a new one, I had someone tell me that I should be sure to get a full-duplex hub or I'd only be seeing half the traffic when I monitor. Really? I've been using a crusty old Netgear DS104 all this time. No clue if it is half or FD. Have I really been understating my measurements? I'm just not bright enough about the physical layer to really know... Side note: Just ordered a Dualcomm Ethernet Switch TAP as a hub replacement. Seems like a nifty gadget. Any notes or tips about it would be welcome in the comments :-)

  Read the article

• Ping not working

  - by Nishant

  Ping is not working to and from this IP to my computer. inet addr:10.125.104.4 Bcast:10.125.111.255 Mask:255.255.240.0 My computer is like this Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.125.65.75 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 10.125.64.6 We both CAN reach the common gateway IP , 10.125.96.6 . What should I check ? What is the barrier in sending info if we both have a common gateway that is pingable ? Besides I can login to a intermediate server and ssh to this server also !!

  Read the article

• Cannot connect to a shared network drive

  - by dublintech

  I am using windows 7, I cannot connect to a shared network drive on another machine. I can ping the machine. I can remote desktop connect to the machine. The machine is on the same subnet My friend with the exact same laptop as me (and on the same network, same workgroup) can connect to the shared folder. The machine I am trying to connect to and my friends machine can both see shared folders on my machine. I also cannot see shared folders on the friends laptop. When I select diagnose, windows tells me nothing useful. When I select see details on the error pop up, I see: Error code: 0x80004005 (google doesn't help much) I can nbtstat -a the machine who has the shared folder. When I try with my firewall turned off the same happens. I have ensured my windows 7 has all updates. I run security essentials to ensure my laptop is clean. I run ccleaner to clean up my registry. Same error. I have tried with my laptop on both wireless and ethernet. As you can imagine, I am banging my head against the wall on this one.

  Read the article

• Wireless Internet Connection Sharing in Ubuntu

  - by klutch2

  As the title states, I need to share a wireless connection with a laptop running Ubuntu as the AP. The setup will be as follows: Corporate WiFi <<== Laptop <<== Other Devices i.e. (iPad, iPhone) I want to be able to connect the "Other Devices" via WiFi to the laptop. I have thought of setting up an ad-hoc network by connecting to the Corporate WiFi and then setting up a new network and hoping the connection to both would stay, but that doesn't seem to work. If I set up the ad-hoc network by itself, I can see it from my "Other Devices". The reason I need this is because for some reason, my iPad and my iPhone will not connect to my corporate WiFi and I need to use them so I want to use my laptop to share the connection and act as an AP for my "Other Devices". My laptop is a Chrome CR-48 running Ubuntu and as some of you might know, it does not have an ethernet port, so having a wired connecting and then setting up a network is out of question. I want to connect to the Corporate WiFi and share that connection by having the laptop act as an AP for other devices.

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Server specification recommendation

  - by foo

  To cut the story short, I can't buy an item (server/cpu/motherboard/ram) that costs more than USD 330. However, I can combine them, meaning, I can buy a CPU that costs USD 330 and motherboard that costs USD 330. With this limitation, I can't buy a powerful 1U server which will definitely costs me more USD 330. With that in mind, I was hoping to build a powerful desktop PC which will be used as a database server. However, through my experience, desktop PC doesn't last very long, usually the motherboard will just die by itself after 1 or 2 years. So, what would you guys recommend me to buy with this kind of budget? Every item must be <= USD 330. Will be used as a MySQL server. RAID would be nice. 1TB is pretty big for my data. I do not need external graphic card (onboard would do just fine), mouse, keyboard, monitor. Linux friendly. One ethernet port is good enough. It's important that those hardware is made of components that will last long (at least 3 years or something). The server will be placed in an air conditioned room, but a good ventilation for the server is always preferred. I won't overclock it. Intel processor is preferred. Thanks in advance.

  Read the article

• MAC-Address based routing

  - by d-fens

  Here is what i want to do: I have a bunch of systems, some might have the same Public-IP, i disable ARP. I have a Firewall (either IP Layer or bridge-FW) between these systems and the internet. Depending on the destination port of incoming IP-Packets to some of these Public-IPs i want to set the destinsation-Ethernet-Adress. So for instance System A has IP 8.8.8.8, mac de:ad:be:ef:de:ad, arp disabled System B has IP 8.8.8.8, mac 1f:1f:1f:1f:1f:1f, arp disabled Firewall has IP 8.8.8.1, arp disabled on that interface Incoming packet to IP 8.8.8.8 tcp dest port 100 Incoming packet to IP 8.8.8.8 tcp dest port 101 Firewall sets dest-mac for 1.) - de:ad:be:ef:de:ad Firewall sets dest-mac for 2.) - 1f:1f:1f:1f:1f:1f Second scenario: System A and System B establish outgoing TCP-Connections, and the firewall matches the dst-mac of the incoming IP-Packets (response packets) to the senders-mac address. is this possible in any way with linux and iptables? edit: i read ebtables might "work" in a hackish way for this purpose but i am not sure...

  Read the article

• How to set up vpn tunnel (ipsec) connection

  - by Alfwed

  I'm working with a client who wants to set up a vpn tunnel between their network and ours. They're in charge of the tunnel and to give us the access they are asking me my public IP and my LAN IP. This is what i've got when i do an ifconfig on the server i will use to connect to the vpn $ ifconfig eth0 Link encap:Ethernet HWaddr d4:ae:52:cd:xx:xx inet adr:62.210.xxx.xxx Bcast:62.210.xxx.xxx Masque:255.255.255.0 adr inet6: fe80::d6ae:52ff:xxxx:xx/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:55255032 erreurs:0 :779628 overruns:0 frame:0 TX packets:5419527 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:5598164393 (5.5 GB) Octets transmis:1034297288 (1.0 GB) Interruption:16 Mémoire:c0000000-c0012800 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:45923382 erreurs:0 :0 overruns:0 frame:0 TX packets:45923382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 The inet adr:62.210.xxx.xxx is my public IP but it seems like i dont have any LAN IP. Can the connection work without LAN IP or should I create a private network somehow?

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >