Search Results

Search found 9044 results on 362 pages for 'bad sector'.

Page 266/362 | < Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >

  • filesystem compatible with freenas and windows

    - by Daniel
    Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

    Read the article

  • Is current SATA 6 gb/s equipment simply unreliable?

    - by korkman
    I have a 45-disk array of Seagate Barracuda 3 TB ST3000DM001 (yes these are desktop drives I'm aware of that) in a Supermicro sc847 JBOD, connected via LSI 9285. I have found a solution for the problem description below by reducing speed via MegaCli -PhySetLinkSpeed -phy0 2 -a0; for i in $(seq 48); do MegaCli -PhySetLinkSpeed -phy${i} 2 -a0; done and rebooting. The question remains: Is this typical for current 6 gb/s equipment? Is this the sad state of SATA storage? Or is some of my equipment (the sff-8088 cables come to mind) bad? The Problem was: Synchronizing HW RAID-6, disks kept offlining. Fetching SMART values reveiled that those which offlined did not increase powered-on hours anymore. That is, their firmware (CC4C) seems to crash. Digging into the matter by switching to Software RAID-6, with the disks passed-through, I got tons of kernel messages scattered across all disks, with 6 gb/s: sd 0:0:9:0: [sdb] Sense Key : No Sense [current] Info fld=0x0 sd 0:0:9:0: [sdb] Add. Sense: No additional sense information And finally, when a disk offlines: megasas: [ 5]waiting for 160 commands to complete ... megasas: [35]waiting for 159 commands to complete ... megasas: [155]waiting for 156 commands to complete ... megaraid_sas: pending commands remain after waiting, will reset adapter. Ugly controller reset here, then minutes later: megaraid_sas: Reset successful. sd 0:0:28:0: Device offlined - not ready after error recovery ... sd 0:0:28:0: [sdu] Unhandled error code sd 0:0:28:0: [sdu] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK sd 0:0:28:0: [sdu] CDB: Read(10): 28 00 23 21 2f 40 00 00 70 00 sd 0:0:28:0: [sdu] killing request Reduced speed to 3 gb/s like written above, all problems vanished.

    Read the article

  • Formatted C: from Windows 7 setup, now it won't even install

    - by ocurro
    Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

    Read the article

  • Forcing a particular SSL protocol for an nginx proxying server

    - by vitch
    I am developing an application against a remote https web service. While developing I need to proxy requests from my local development server (running nginx on ubuntu) to the remote https web server. Here is the relevant nginx config: server { server_name project.dev; listen 443; ssl on; ssl_certificate /etc/nginx/ssl/server.crt; ssl_certificate_key /etc/nginx/ssl/server.key; location / { proxy_pass https://remote.server.com; proxy_set_header Host remote.server.com; proxy_redirect off; } } The problem is that the remote HTTPS server can only accept connections over SSLv3 as can be seen from the following openssl calls. Not working: $ openssl s_client -connect remote.server.com:443 CONNECTED(00000003) 139849073899168:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 226 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Working: $ openssl s_client -connect remote.server.com:443 -ssl3 CONNECTED(00000003) <snip> --- SSL handshake has read 1562 bytes and written 359 bytes --- New, TLSv1/SSLv3, Cipher is RC4-SHA Server public key is 1024 bit Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE SSL-Session: Protocol : SSLv3 Cipher : RC4-SHA <snip> With the current setup my nginx proxy gives a 502 Bad Gateway when I connect to it in a browser. Enabling debug in the error log I can see the message: [info] 1451#0: *16 peer closed connection in SSL handshake while SSL handshaking to upstream. I tried adding ssl_protocols SSLv3; to the nginx configuration but that didn't help. Does anyone know how I can set this up to work correctly?

    Read the article

  • System recognizes admin password on the Welcome screen but not when elevating

    - by Lee C.
    I set up Windows 7 with a couple of standard accounts, and an administrator account (called Odin). I can log in to Odin just fine from the Welcome screen. While logged into Odin I can do anything that requires administrator privileges without a password: just hit Yes in the User Account Control dialog. If I am logged into one of the other accounts and I do something that requires elevation (e.g. most installers, and some control panel functionality), then Windows presents me with a User Account Control dialog asking "Do you want to allow the following program to make changes to this computer? To continue, type an administrator password, and then click Yes." The account shown in this dialog is Odin, so I enter Odin's password. But Windows redisplays the dialog with the message "Logon failure: unknown user name or bad password." This always happens, and has done so for many months, probably since I first got the computer. Why does Odin's password work from the Welcome screen, but not when elevating? Please note that I am not asking how to recover Odin's password. I remember the password I originally set for Odin, and it works as it should from the Welcome screen, but is not recognized when elevating. The password has no funny characters, just letters and digits. Thanks!

    Read the article

  • How would I setup iMail to forward a user's mail to another service w/o leaving a copy locally?

    - by Scott Mayfield
    I have an iMail 2006 server installation in which I have a particular user that has several aliases that all point to a single user (me, for the record). I've been copying all of my mail to GMail and reading it there, but it annoys me that I have to go back weekly and log into my mail account on iMail and delete between 6 and 10 thousand copies of messages I've already received, in order to keep my mailbox from filling up (yes, I have it set with no quota, but I consider it bad form to just let the box grow indefinitely). I've got the copying setup via an inbound user rule, but I'm wondering how to accomplish a "copy and delete" rule. The manual isn't clear on what happens with multiple matching rules (will they be processed in order, or is it a first match situation?) and there isn't a means to combine multiple actions into a single rule. If I use the "forward" action, I THINK that it's going to screw up all the sender information once the mail reaches my GMail account and show it as coming from me instead of the original senders (can anyone confirm that this is accurate?) An easy answer would be to delete my user account entirely, replace it with an alias that maps to my GMail account, but then I would lose my ability to log into the system for admin duties. So that leads me to creating a second, lesser known account for admin use, but since it's a real account, sooner or later I'm going to get mail sent to it and I'll be back to the same situation of having a user account that doesn't get emptied periodically. I imagine I can set the quota to 0 MB to cause all incoming mail to my admin account to bounce, or setup an inbound rule to bounce everything, but this is starting to sound kludgy to me. Does anyone know of a more direct work around to copying a user's incoming mail to an outside server and then deleting the local copy w/o removing their account entirely? Or is this just wishful thinking? Thanks in advance. Scott

    Read the article

  • Using Toshiba 22EL833 as PC display through HDMI input

    - by Oleg V. Volkov
    I had another Toshiba TV - 19SL738 - connected to this same PC and video card (GTX 8800) through DVI<-HDMI (DVI on PC side, HDMI on TV) before, that was working perfectly at it's native resolution 1360x768. Some time ago I had to change to 22EL833 and immediately faced problem with Windows 7 control panel and NVIDIA control panel both reporting native resolution for new TV as 1080i, 1920x1280, despite TV documentation saying that it have same 1360x768 as previous one. Practical tests confirmed that true native resolution is indeed 1360x768, because plugging in through DVI<-VGA and setting custom resolution through NVIDIA panel shown clear colors and crisp image, while setting anything different with either DVI<-VGA or DVI<-HDMI produced horribly distorted or squished images, with almost unreadable slim lines (as in letters, for example). Now, my problem is that there's no drivers for this TV and I'm unable to get good image while connecting it through DVI<-HDMI directly. The best I've achieved is editing EDID/driver manually, to persuade system that native resolution should be 1360x768, and while image became mostly clear, colors turned to some strange washed out effect, with pools of pure yellow, cyan and magenta there and there filling place of other colors. Gradients also became noticeably stripped as well. Somehow it looks like dithering gone bad and makes me suspect that image is still down/upscaled several times internally somewhere along the line. How can I connect this TV to DVI output of my video card to get best possible clear image, correct colors and correct native resolution?

    Read the article

  • Desktop bigger than screen

    - by alex
    I am using MSI U115 11" netbook (OS: Windows XP Home, graphics card: Intel Graphics Media Accelerator 500) and today after I switched it on, desktop was bigger than screen. To be exact: screen resolution was set to the lowest possible and I could move mouse outside of screen (but only below - left, right and up worked normally, mouse could not exceed screen boundaries). I changed resolution back to normal, but the problem with desktop being bigger than screen remained (as before, only lower part - cannot see task bar, etc. When I hit windows button on keyboard, only upper part of menu start is visible). What I already tried was changing all kind of graphics and screen settings - none of them helped. I also tried to restore the system to few days before, but it didn't help neither. What can I do to make the desktop look "normally"? EDIT: Some additional info regarding screen: Sorry it's in polish - but let me explain. There are two screens I can choose (Monitor domyslny means default screen), but the second one (the default one) is not available. After I choose it and click apply number 1. is used (and as you can see it has only two resolutions available. There are more in the second one - but without 1024x600 though). The two ticked and grayed out options here are Use this screen as the main one and Enlarge Windows desktop to match this monitor's size. Too bad I cannot change them. When I choose the second screen, the first box is unchecked and grayed out. The second box is available to be changed but it doesn't matter anyway as after applying changes it reverts to the first screen anyway. EDIT: Intel Graphics Media Control Panel screenshot.

    Read the article

  • Clipboard bug in Wordpad in Windows 7 (accidentally pasting large file into application)

    - by frenchglen
    In Win7, I use Wordpad, and I really like it. For my needs it's lean and fast, yet has the formatting functionalities I'm after when working on my TXT/RTF files on a daily basis. I don't intend to change text editors. There's a really bad bug which has ALWAYS plagued me. If you have a large file contained in the clipboard, like a 238MB FLAC file, and you accidentally paste it into Wordpad for whatever reason - it hangs the application for a VERY long time (like 2 hours, it depends on how big the file is, because it tries to 'handle' it). You either have to close the application and lose any unsaved changes, or go do something else until the item has finished pasting into Wordpad (it actually eventually drops the file's icon in wordpad just like how it appears in Windows Explorer). It's a Windows bug, a Wordpad bug. Is there some solution for this? Or is the problem fixed in Windows 8 (if anyone can tell me)? .....I'm not going to try out Win8 myself, merely to answer this question - that's what I'm asking it on SuperUSer for! I'm really hoping it's one of those little-yet-big things that they've fixed in Win8 (like removing the 255-character file path limit in Explorer, which is awesome). Thank you for your help, if you have Win8 handy and can test this. :)

    Read the article

  • FreeBSD ZFS RAID-Z2 performance issues

    - by Axel Gneiting
    I'm trying to build my own network attached storage based on FreeBSD+ZFS+standard components, but there are strange performance issues. The hardware specs are: AMD Athlon II X2 240e processor ASUS M4A78LT-M LE mainboard 2GiB Kingston ECC DDR3 (two sticks) Intel Pro/1000 CT PCIe network adapter 5x Western Digital Caviar Green 1.5TB I created a RAID-Z2 zpool from all disks. I installed FreeBSD 8.1 on that zpool following the tutorial. The SATA controllers are running in AHCI mode. Output of zpool status: pool: zroot state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raidz2 ONLINE 0 0 0 gptid/7ef815fc-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/80344432-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/81741ad9-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/824af5cb-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/82f98a65-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 The problem is that write performance on the pool is very very bad (<10 MB/s) and every application that is accessing the disk is unresponsive every few seconds when writing. It seems like writing is fine until the ZFS ark cache is full and then ZFS stalls the entire system I/O till it's finished writing that data. Also I'm getting kmem_malloc to small kernel panics. I've already tried to put vm.kmem_size="1500M" vm.kmem_size_max="1500M" into /boot/loader.conf, but it doesn't help. Does anyone know what's going on here? Am I really not having enough memory for ZFS to handle this RAID-Z2?

    Read the article

  • Mac OS X Disk Encryption - Automation

    - by jfm429
    I want to setup a Mac Mini server with an external drive that is encrypted. In Finder, I can use the full-disk encryption option. However, for multiple users, this could become tricky. What I want to do is encrypt the external volume, then set things up so that when the machine boots, the disk is unlocked so that all users can access it. Of course permissions need to be maintained, but that goes without saying. What I'm thinking of doing is setting up a root-level launchd script that runs once on boot and unlocks the disk. The encryption keys would probably be stored in root's keychain. So here's my list of concerns: If I store the encryption keys in the system keychain, then the file in /private/var/db/SystemKey could be used to unlock the keychain if an attacker ever gained physical access to the server. this is bad. If I store the encryption keys in my user keychain, I have to manually run the command with my password. This is undesirable. If I run a launchd script with my user credentials, it will run under my user account but won't have access to the keychain, defeating the purpose. If root has a keychain (does it?) then how would it be decrypted? Would it remain locked until the password was entered (like the user keychain) or would it have the same problem as the system keychain, with keys stored on the drive and accessible with physical access? Assuming all of the above works, I've found diskutil coreStorage unlockVolume which seems to be the appropriate command, but the details of where to store the encryption key is the biggest problem. If the system keychain is not secure enough, and user keychains require a password, what's the best option?

    Read the article

  • PHP crashing during oAuth scripts

    - by FunkyChicken
    I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

    Read the article

  • Will these instructions work when turning of journaling on a n ext4 SSD?

    - by snowlord
    I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

    Read the article

  • CloudFlare dashboards empty, or performance issues

    - by Katafalkas
    I wanted to test CloudFlare performance so I set my image gallery domain on it and started testing. I have added PageRules for caching. And chose the Security: Essentially Off. I checked NS check tools and they say that my domain name is propagated with CloudFlare. For testing purpose I created a link that loads 200 images from that server, and was using loads.in website to determine how much it is faster. After trying few regions, I noticed that there were no improvement in loading speed. So I looked up the dashboards, and it was empty. I am not sure if I am doing something wrong, or made some error in my setup, or it takes few days to start caching or working properly, but at the moment - after a day of testing - dashboards are empty. Also the NS check tools sais that all name servers are propagated to CloudFlare and working fine. So I assume I got a bad performance because it is simply not working. I sent a letter to CloudFlare support team, but did not get any straight answer. So essentially my question is: Anyone has any experience with CloudFlare ? How long does it take for it to start caching static content to CDN ? Or there is simply something I am doing wrong ?

    Read the article

  • Windows 7 restarts while being idle

    - by Ondrej Slinták
    My Windows 7 almost always restarts when I keep it idle for ~20-30mins. It happened randomly before, but lately, if I leave the computer I can be sure it's gonna restart after those 30mins. It never happens when I play games or work tho, just when it's idle. It's a fresh install of Windows 7 64bit. I had also problems while installing it, it always crashed while finalizing the install and I had to reinstall again. Eventually it installed on 3rd or 4th try after I deleted all of my partitions and added them again. I thought it might have been a hardware problem, but temperatures seem to be okay and I have no idea how to track what might have been causing it. Any ideas? I'm running Windows 7 64bit on: Gigabyte EX58-UD4P Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz NVIDIA GeForce GTX 260 6GB of DDR3 1066Mhz RAM WDC WD1001FALS-00J7B0 1TB SATA II I have a very bad feeling it might be something with HDD and its compatibility with Windows 7 as I haven't had those problems for 1 year while I had Vista.

    Read the article

  • Virtual Fileserver

    - by Sergei
    Hi, We are planning to move our production servers to the datacenter and virtualize remaining servers in the process.Datacenter will have HP blades with vSphere on top.Currentliy we are using Celerra NS20 as fileserver.Since datacenter is using HP kit and EVA 4400 as SAN, we cannot have Celerra there, as EMC supoprt for Celerra does not work for non EMC array. I have searched for possible options and one of them was to have HP NAS blade X3800sb instead of Celerra.However this seems like overkill for me.We are only using Celerra for about 100 users and 50 servers and I think having X3800sb could be waste of resources. The other option would be to have a virtual fileserver as a part of vmware environment in datacenter.We only need CIFS to be provided.The only option I can think of is Windows Storage server.We had a bad expirience with Windows servers used as fileservers ( memory leaks one thing) in the past and this was one of the reasons we moved to Celerra. What are the other options?We need something as reliable as Celerra with as many options as possible.For example , Celerra has per folder quotas, deduplication, dynamic volume allocation, automatic failover, VTLU, replication. Also we would need to replicate NAS data to the failover site.We could use block level replication , SAN-to-SAN, but this would mean wasted bandwidth, as we need only subset of folders to be replicated.We used CA XSoft for windows servers in the past and Celerra has option for Celerra replication. Thank you very much in advance, Please ask me if I missed any details!

    Read the article

  • How would I setup iMail to forward a user's mail to another service w/o leaving a copy locally?

    - by Scott Mayfield
    I have an iMail 2006 server installation in which I have a particular user that has several aliases that all point to a single user (me, for the record). I've been copying all of my mail to GMail and reading it there, but it annoys me that I have to go back weekly and log into my mail account on iMail and delete between 6 and 10 thousand copies of messages I've already received, in order to keep my mailbox from filling up (yes, I have it set with no quota, but I consider it bad form to just let the box grow indefinitely). I've got the copying setup via an inbound user rule, but I'm wondering how to accomplish a "copy and delete" rule. The manual isn't clear on what happens with multiple matching rules (will they be processed in order, or is it a first match situation?) and there isn't a means to combine multiple actions into a single rule. If I use the "forward" action, I THINK that it's going to screw up all the sender information once the mail reaches my GMail account and show it as coming from me instead of the original senders (can anyone confirm that this is accurate?) An easy answer would be to delete my user account entirely, replace it with an alias that maps to my GMail account, but then I would lose my ability to log into the system for admin duties. So that leads me to creating a second, lesser known account for admin use, but since it's a real account, sooner or later I'm going to get mail sent to it and I'll be back to the same situation of having a user account that doesn't get emptied periodically. I imagine I can set the quota to 0 MB to cause all incoming mail to my admin account to bounce, or setup an inbound rule to bounce everything, but this is starting to sound kludgy to me. Does anyone know of a more direct work around to copying a user's incoming mail to an outside server and then deleting the local copy w/o removing their account entirely? Or is this just wishful thinking?

    Read the article

  • Problems with "Read Only" on a Samba share from Windows machines

    - by fistameeny
    We have a Ubuntu 10.04 Server that has a bunch of Samba shares on it that Windows workstations connect to. Each Windows workstation has a valid username/password to access the shares, which have restricted access governed by Samba. The problem we are experiencing is that Samba doesn't seem to be able to mimic the Windows way of handling "Read Only" attributes. Say I have two users, UserA and UserB, both a group called Staff - UserA creates a file that is readable/writeable by the group (ie. chmod rwxrwx---). If UserA then sets the "Read Only" flag, this changes the permissions to r-xr-x--- (i.e. no write for anyone). As UserB is in the same group as UserA, they should be able to remove the "Read Only" permission - however, they can't as Samba won't allow it. Is there a way to force Samba to allow users within the same group to remove the "Read Only" from a file not created by them? Edit: The Samba smb.conf is as follows: The share is defined in the smb.conf as: [global] log file = /var/log/samba/log.%m passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . obey pam restrictions = yes map to guest = bad user encrypt passwords = true passwd program = /usr/bin/passwd %u passdb backend = tdbsam dns proxy = no netbios name = ubsrv server string = ubsrv unix password sync = yes os level = 20 syslog = 0 usershare allow guests = yes panic action = /usr/share/samba/panic-action %d max log size = 1000 pam password change = yes workgroup = workgroup [Projects] valid users = @Staff writeable = yes user = @Staff create mode = 0777 path = /srv/samba/Projects directory mode = 0777 store dos attributes = Yes The folder itself looks like this: ls -l /srv/samba/ drwxrwxrwx 2 nobody Staff 4096 2010-11-04 10:09 Projects Thanks in advance, Matt

    Read the article

  • Xen PV packet loss

    - by Delphinator
    I'm having some serious issues with packetloss with one of my servers. This server is a somewhat old (P4-era) machine running Debian Squeeze and Xen 4.0. There are two domUs running on it (both also Debian Squeeze), one gateway and a fileserver. Unfortunatly the processor has no virtualization extensions, therefore only PV can be used. While investigating why our network seems to be slower than it should I found some pretty bad packet loss (~25%). After further investigation and several experiments I did a measurment between the dom0 and one of the domUs: Server listening on UDP port 5001 Receiving 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ ------------------------------------------------------------ Client connecting to dom0, UDP port 5001 Sending 1470 byte datagrams UDP buffer size: 110 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.2(domU) port 33817 connected with 192.168.1.100(dom0) port 5001 [ 4] local 192.168.1.2(domU) port 5001 connected with 192.168.1.100(dom0) port 48606 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 46.3 MBytes 38.7 Mbits/sec [ 3] Sent 33020 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 46.2 MBytes 38.6 Mbits/sec 0.030 ms 89/33019 (0.27%) [ 3] 0.0-10.0 sec 1 datagrams received out-of-order [ 4] 0.0-10.2 sec 43.0 MBytes 35.3 Mbits/sec 13.074 ms 11575/42256 (27%) tl;dr: 27% packet loss from dom0 to domU with 50Mbit UDP packets. Same thing happens from anywhere in the network. The problem gets better for smaller bandwidths (0.047% for 5Mbit) and worse for higher (59% for 200Mbit) ones. I did increase the CPU-weight of the dom0, there is no swapping going on, and actual networking-hardware is not involved. I never expected Xen (or anything related) to drop packets, and I'm completly clueless what to try next.

    Read the article

  • Is there a way to do something like LVM over NFS?

    - by warren
    I realize that since NFS is not block-level, LVM can't be used directly. However: is there a way to combine multiple NFS exports (from, say, 3 servers) into one mount point on a different server? Specifically, I'd like to be able to do this on RHEL 4 (or 5, and re-export the combined mount to my RHEL 4 server). expansion The reason I pegged lvm is that I want a bunch of exported mounts (servera:/mnt/export, serverb:/mnt/export, serverc:/mnt/export, etc) to all mount at /mnt/space so that my /mnt/space on this server (serverx) as one large filesystem. Yes, I know that re-exporting is generally a Bad Thing™ but thought it might work, if there was a way to accomplish this on a newer release as opposed to an older one From reading the unionfs docs, it appears that I can't use it over a remote connection - have I misread it? More accurately, since Union FS merges the contents of multiple branches, but makes them appear as one, it doesn't seem to go in reverse: I'm trying to mount a bunch of NFS points in a merged fashion, then write to them - not caring where data goes, a la LVM .

    Read the article

  • PHP-FPM issue on LEMP Stack and WordPress

    - by jw60660
    I'm very much a NGINX and Server Admin beginner. I used this tutorial to install NGINX / PHP / mySQL / WordPress: C3M Digital Tutorial In this tutorial the backend php-cgi setup is configured using fastcgi. php5-fpm was installed during this tutorial: apt-get install nginx-full php5-fpm php5 php5-mysql php5-apc php5-mysql php5-xsl php5-xmlrpc php5-sqlite php5-snmp php5-curl After reading that the NGINX configuration on the WordPress codec was more secure than most tutorials, I decided to use the codex configuration: WordPress NGINX configuration in Codex The Codex configuration uses php-fpm for backend php-cgi. When opening the browser I got a 502 Bad Gateway error. The error log was: "2012/06/10 21:18:27 [crit] 14009#0: *4 connect() to unix:/tmp/php-fpm.sock failed (2: No such file or directory) while connecting to upstream, client: 12.3.456.789, server: mywebsite.com, request: "GET / HTTP/1.1", upstream: "fastcgi://unix:/tmp/php-fpm.sock:", hos t: "mywebsite.com"" In the main NGINX configuration file supplied by the codex I noticed the line starting "server unix:" in the upstream php block which point to the empty directory: # Upstream to abstract backend connection(s) for PHP. upstream php { server unix:/tmp/php-fpm.sock; # server 127.0.0.1:9000; } I checked the folder at /tmp and it was empty. Seems I missed configuring php-fpm to play with NGINX. Can someone point me in the right direction? Much appreciated!

    Read the article

  • Visual Studio 2010 Beta 2, built-in font smoothing

    - by L. Shaydariv
    I've just installed Visual Studio 2010 Beta 2 onto my Windows XP to evaluate it and check whether it meets my preferences the way it did before. Okay, I've temporary defeated an urgent bug with a strange workaround (I could not open any file from the Solution Explorer), and it left bad memories to me. But however, it's okay. The first thing I've seen just opening the code editor was ClearType font rendering. Wow, so unexpectedly. I must note that I do not use standard Windows rendering techniques, but I still prefer GDI++, a font renderer developed by Japanese developers. (GDI++ allows to render the fonts in Mac/Win-Safari style over entire Windows.) Personally for me, GDI++ reaches the great font-rendering results allowing me to use the Dejavu Sans Mono font with really nice smoothing in Visual Studio 2008 (VS 2005 too, though VS 2005 crashes in this case). But GDI++ cannot affect Visual Studio 2010 Beta 2 text editor - it uses ClearType (right?), and it does not care about the system font smoothing settings. It could be an editor based on WPF, right? So as far as I can see, I can't use GDI++ anymore because it uses Windows GDI(+) but no WPF? So I've got several questions: Is it possible to disable VS 2010 b2 built-in ClearType or override it with another font smoother? Is it possible to install a Safari-like font renderer for Visual Studio 2010 [betas]? Thanks a lot.

    Read the article

  • Uninstall php5 installed from source

    - by diegomichel
    I have tried to install php5 from source , and it worked... Then for some reason need to install the official packets, so i tried a make uninstall and for my surprise there is such make uninstall... so i tried delete all the installed files by hand. Then installed the official debian packages and it worked fine... till i need install sqlite module, which give me the following error: php --version PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626/pdo_sqlite.so' - /usr/lib/php5/20090626/pdo_sqlite.so: undefined symbol: php_pdo_register_driver in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626/sqlite.so' - /usr/lib/php5/20090626/sqlite.so: undefined symbol: php_pdo_register_driver in Unknown on line 0 PHP 5.3.1-5 with Suhosin-Patch (cli) (built: Feb 22 2010 22:46:05) Copyright (c) 1997-2009 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2009 Zend Technologies So i remember that manual install i did, and i think there is some old lib installed causing that problem, the bad thing is that there is not such make uninstall on the source code of php5... php-5.2.13 > make uninstall make: *** No rule to make target `uninstall'. Stop. I have tried reinstall and purge all php related packages via aptitude with not success. OS: Debian Squeeze. uname -a Linux desktop 2.6.32-trunk-amd64 #1 SMP Sun Jan 10 22:40:40 UTC 2010 x86_64 GNU/Linux Any idea how to fix that?

    Read the article

  • ubuntu 9.10 installer doesn't recognize the hard drive

    - by dan
    I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

    Read the article

  • Facing error: "Could not open a connection to your authentication agent."; trying to add ssh-key.

    - by Kaustubh P
    I use ubuntu server 10.04. ssh-add /foo/cert.pem gave the following output Could not open a connection to your authentication agent. These are my running processes: ps -aux | grep ssh Warning: bad ps syntax, perhaps a bogus '-'? See http://procps.sf.net/faq.html root 1523 0.0 0.0 49260 632 ? Ss Dec25 0:00 /usr/sbin/sshd root 10023 0.0 0.3 141304 6012 ? Ss 12:58 0:00 sshd: padmin [priv] padmin 10117 0.0 0.1 141304 2400 ? S 12:58 0:00 sshd: padmin@pts/1 padmin 11867 0.0 0.0 7628 964 pts/1 S+ 13:06 0:00 grep --color=auto ssh root 31041 0.0 0.3 141264 5884 ? Ss 11:24 0:00 sshd: padmin [priv] padmin 31138 0.0 0.1 141264 2312 ? S 11:25 0:00 sshd: padmin@pts/0 root 31382 0.0 0.3 139240 5844 ? Ss 11:26 0:00 sshd: padmin [priv] padmin 31475 0.0 0.1 139372 2488 ? S 11:27 0:00 sshd: padmin@notty padmin 31476 0.0 0.0 12468 964 ? Ss 11:27 0:00 /usr/lib/openssh/sftp-server These are my environment variables: $ env | grep SSH SSH_CLIENT=192.168.1.13 42626 22 SSH_TTY=/dev/pts/1 SSH_CONNECTION=192.168.1.13 42626 192.168.1.2 22 What is wrong? Why cant I add any identities? Thanks.

    Read the article

< Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >