Search Results

Search found 10050 results on 402 pages for 'graphics card'.

Page 318/402 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

• How can I play 24Bit 96000Hz vinyl rips?

  - by Peter

  I am getting music through the Nvidia HDMI but it is all down-sampled to 44000Hz. I have spent at least 3 hours searching for an answer yesterday. I use Pulse Volume and I even changed the default settings in the Pulse folder to 96000 but it does not work. Though 5.1 sound works perfectly. They all work well in Windows 7, but I prefer to use Ubuntu. All the config files for all the programs are in the etc folder, then look in the pulse folder, and there are 3 three files, 2 of these I changed the permissions and I changed 16 and 44000 to 24 and 96000 as I had read in another forum, but it worked for them and not for me. Though 5.1 works as I have special mp4 file that can check each channel. I did alot of restarts and checking after these changes as nothing had happened, my amp tells me the freq of the signal, which does work which I have tested on Windows 7. I have also gone to systems to download the latest driver for mu Nvidia card. But even if it does not work, I guess I can always play Cd's. But I think my player have become more unstable since I changed the configs, so I may uninstall and install Pulse Volume Control again.

  Read the article

• Brightness going up to 100% on loading certain websites in Chrome

  - by picheto

  I'm using Google Chrome version 21.0.1180.89 on Ubuntu 12.04 and my laptop is a Sony VAIO VPCCW15FL (spec sheet). My video driver is the propietary "NVIDIA accelerated graphics driver (post-release updates)(version-current updates)". After installing Ubuntu, I discovered that neither the brightness control buttons (hardware) or the brightness slider (software) worked, and found out I could get the hardware buttons to work by installing the nvidiabl.deb package and oBacklight script. I'm using nvidiabl-dkms 0.77 and oBacklight 0.3.8. Still, the slider on the Ubuntu "Settings" does not work, but I don't care. There is an annoying thing happening when loading certain pages in Google Chrome: the brightness goes up to 100% when loading the webpage or when leaving it (closing the tab or typing a different URL on the omnibox). However, the "brightness tooltip" (that default brightness notification) remembers the position it was set to, so if I adjust the brightness with the HW buttons, the level gets adjusted relative to the value it was set to before "going 100%". I disabled the flash PPAPI plugin, but left the NPAPI plugin enabled, and the problem went away for pages with flash content. Still, the same thing happens when viewing HTML5 video, or when loading, for example, the Chrome Web Store or using the Scratchpad extension. I suppose it has to do with the rendering of certain elements using the GPU, but this is just a guess. This brightness thing does not happen when using Firefox 15.0 or any other application I have used yet. Does anybody know why this may be happening and what could I do to fix this without changing browser? Thanks a lot.

  Read the article

• SSD on USB 3.0 doesnt always mount

  - by juergen

  I would like to ask you for some support for this issue. The SSD I use is apparently slightly damaged. Atm it shows this popular Corsair Series 3 problem. symptom: the disk is working for some minutes and then just suddenly stops. Two months ago it worked like a charm. This was my boot device in these days. So now I still need to copy some data out of the device which leads me to my question. Usually the SSD is working again for some minutes, when i unplug and replug its power. It gets detected by the system again and I can continue my backup. The problem on Ubuntu is, that it is not recognized again after two or three replugs. I have to reboot to bring it back. To specify this situation: when i unplug and replug my USB mouse before i reboot it is not recognized as well. So something seems to be wrong with the system also. my question: how do i fix this rebooting issue? I will post all the logs you need to analyse. The problem doesnt depend on the interface. I tried USB3.0, 2.0 and Sata already. Thank you! cheers my system: Ubuntu 11.10, Gigabyte G41MT-S2P, Intel E6750 Corsair Force Series 2 - F120, Digitus USB 3.0 Adapter, USB 3.0 interface card

  Read the article

• rfid programming

  - by MaKo

  hi guys, I got a gift from a friend, 2 readers for RFID, and some cards (from a Chinese company called daily rfid), the kind of work, because it comes with some demo software written in Delphi, that reads the id of the card (myfare compatible, ISO14443A ) but the problem is that if I try to use the demo to write to them, it doesnt seem to work, it have another demo written in c#, (compiled and executable from /bin/debug, the DL600DemoCSharp.exe), the software opens, but when click on connect, I get this error Unhanded exception.. unable to load DLL 'BasicB.DLL' so I load the dll on windows/system32, but when I try regsvr32 BasicB.dll I get, error the module "BasicB.dll" was loaded but hte entry-point DllRegisterServer was not found. Make sure that "BasicB.dll" is a valid DLL or OCX file and then try again have written to the company but no response, I program in objective C, so I kind of understand c#, but how to make this cards work? - shall I continue with the delphi, and try to write to them with it - or with c# - either way I would have to write the code to read write to them,, or is there any software to work with this modules?? thanks a lot!

  Read the article

• Almost working 2D Collisions

  - by TheGag96

  I'm terribly sorry I'm asking this question YET AGAIN, but I can almost guarantee that this will be the last time I'll have to ask. I'm currently on the verge of FINALLY getting these collisions to work for my game, made with libGDX in Java. My collisions use the same method as (and are basically copied and modified code from) the XNA Platformer example (here) where the direction of the collision is based on the rectangle where two objects are overlapping. The collisions themselves almost work perfectly, but for some reason, holding down/up and left and colliding with the floor/ceiling while doing so doesn't seem to work well. I'm not at all sure why. Instead of vaguely giving my problem and snippets of code, I've decided to instead provide a binary and the source of the game I have so far so you can see for yourself what my problem is. Link. (Note: make sure you unzip everything into a folder somewhere or it will not work) You'll find the collision code in the method workingCollisions() in Link.java. Please excuse the messy code and terrible graphics as this whole thing is in pre-pre-alpha. If anyone is kind enough and helps me out here, you are the best person ever. I'm completely desperate; I've been trying this on and off for months and I just can't get it to work. I cannot thank you enough.

  Read the article

• How to prevent Network Manager from auto creating network connection profiles with "available to everyone" by default

  - by airtonix

  We have several laptops at work which use Ubuntu 11.10 64bit. I have our Wifi Access Point requiring WPA2-EAP Authentication (backed by a LDAP server). I have the staff using these laptops when doing presentations by using the Guest Account. So by default when you have a wifi card, network manager will display available Wireless Access Points. So the logical course of action for a Novice(tm) user is to single left click the easy to use option in the Network Manager drop down list... At this point the Staff Member (who is logged in with the guest account) expects to just be able to connect and enter any authentication details if required. But because they are using the Guest account, they won't ever have admin permissions (nor do I want them to), and so PolKit kicks in with a request for admin authorisation. I solved this part by modifying the PolKit permissions required to allow all users to create System Network Connections... However, because these Staff members are logging onto the Wifi Access Point with Ldap Credentials and because the Network Manager is now saving those credentials as a System Connection, their password is available for the next guest user session (because system connection profiles are stored in /etc/NetworkManager/system-connections.d/* ). It creates system connections by default because "Available to all users" is ticked by default when you quickly connect to a new wifi access point. I want Network Manager to not tick this by default. This way I can revert the changes I made to Polkit and users network connection profiles will be purged when they log out.

  Read the article

• Is it possible to get xRandR to see two separate outputs with the nvidia driver?

  - by rumtscho

  I have two monitors, which I have set up with nvidia-settings in Twinview. The result: When I want to do something in xRandR, it does not function. It doesn't report one output per video card head, but a single output mapped to the combined area of both monitors: rumtscho@bradbury:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 3840 x 1440, current 3840 x 1440, maximum 3840 x 1440 default connected 3840x1440+0+0 0mm x 0mm 3840x1440 50.0* Now I promised somebody to help test a driver. The developer is using an open source driver for Intel video cards, and his driver assumes that there is more than one xRandR output, each mapped to a monitor. So I tried rewriting my xorg.conf to somehow get two outputs to show up, but failed. Googling showed that people faced with the xRandR-nvidia problem either stopped using xRandR and achieved what they needed with nvidia-settings, or changed their driver to nouveau. The first is not going to help in my situation, and I am not willing to give up the proprietary driver, because Compiz won't work without it. So does anybody know a way to get nvidia to actually pass on information on outputs to xRandR?

  Read the article

• New Write Flash SSDs and more disk trays

  - by Steve Tunstall

  In case you haven't heard, the Write SSDs the ZFSSA have been updated. Much faster now for the same price. Sweet. The new write-flash SSDs have a new part number of 7105026 , so make sure you order the right ones. It's important to note that you MUST be on code level 2011.1.4.0 or higher to use these. They have increased in IOPS from 6,000 to 11,000, and increased throughput from 200MB/s to 350MB/s.    Also, you can now add six SAS HBAs (up from 4) to the 7420, allowing one to have three SAS channels with 12 disk trays each, for a new total of 36 disk trays. With 3TB drives, that's 2.5 Petabytes. Is that enough for you? Make sure you add new cards to the correct slots. I've talked about this before, but here is the handy-dandy matrix again so you don't have to go find it. Remember the rules: You can have 6 of any one kind of card (like six 10GigE cards), but you only really get 8 slots, since you have two SAS cards no matter what. If you want more than 12 disk trays, you need two more SAS cards, so think about expansion later, too. In fact, if you are going to have two different speeds of drives, in other words you want to mix 15K speed and 7,200 speed drives in the same system, I would highly recommend two different SAS channels. So I would want four SAS cards in that system, no matter how many trays you have. 

  Read the article

• Dedicated Servers: Is one better then two for LAMP pseudo HA setup? [closed]

  - by bikedorkseattle

  Possible Duplicate: How to find web hosting that meets my requirements? I know there are zillions of commentary about hosting out there, but I haven't read much about this. Our current well known host is having too many problems, the hardware we are on it subpar, and I'm ready to leave. A day of downtime can cost as much as our monthly hosting bill. A month of bad performance is just killing us right now, user and google wise. I'm wondering about running two dedicated boxes for LAMP, one running as the primary Nginx/Apache (proxy pass), and the other as the MySQL box. Running a single box scares the bejesus out of me because who knows how long it will take anyone to fix a raid card or whatever. The idea is to set this up using some sort of failover system using pacemaker and heartbeat. If one server goes down the other can take over for the other running both web and db. There are some good articles over at Linode about this. I have a few DBs that are 1GB+ and would like to load them into memory. Because of this, I'm shying away from a Linode HA setup because for the price I could do it with two dedicated like I described. Am I mad or an idiot? What are people out there doing for pseodu high availability good performance setups under $400/month? I'm a webmaster; I do a lot of things none of it that well :)

  Read the article

• What is the standard technique for shifting the frames of a sprite according to user input?

  - by virtual__

  From my own experience, I developed two techniques for changing the sprites of a character that's reacting to user input -- this in the context of a classic 2D platformer. The first one is to store all character's pixmaps in a list, putting the index of the currently used pixmap in an ordinary variable. This way, every time the player presses a key -- say the right arrow for moving the character forward -- the graphics engine sees what's the next pixmap to draw, draws it, and increments the index counter. That's a pretty common approach I believe, the problem is that in this case the animation's quality depends not only on the number of sprites available but also on how often your engine listens to user input. The second technique is to actually play an animation every key press event. For this you can use any sort of animation framework you want. It's only necessary to set the timer, the animation steps and to call the animation's play() method on your key press event handler. The problem with that approach is that is lacks responsiveness, since the character won't react to any input while the current animation is still being played. What I want to know is whether you are using one of these techniques -- or something similar -- in your games, or whether there's a standard method for animating sprites out there that's widely known by everybody but me.

  Read the article

• Problems loading Hilva tutorials

  - by Beska

  I'm a newcomer to XNA, and I'm evaluating some libraries. The Hilva Graphics Engine looks interesting, and I'm trying to run their tutorials. However, all of them give me errors. For example, if I download the ParallaxMappingSample demo, and try to build it, I get Error 1 Error loading pipeline assembly "C:\Users\Me\Desktop\ParallaxMappingSample\Hilva.Content.dll". ParallaxMappingSample I get similar errors for all of the samples. Unfortunately, this error isn't very enlightening. I can see the Hilva.Content.dll in the appropriate directory. I tried removing and readding the reference from the content project, but I get the same error. I'm not sure it's relevant, but I'm on Windows 7, I'm using Microsoft Visual Studio 2010, and XNA 4.0. Is there an easy (or difficult) solution? EDIT: If you happen to try this, even if you don't have a solution, let me know about it in a comment. Whether it works for you, or if you get the same problem...either result would be something that might let me know if it's just a problem with the tutorial, or if it's on my end.

  Read the article

• Xlib: extension "GLX" missing on display ":0". Asus k53s

  - by Steve

  I had everything working fine, I use a number of openGL graphics software, example pymol, mgltools, vmd, ballview, rasmol etc. All of these give the error: Xlib: extension "GLX" missing on display ":0". and fail to initialize. I have an i7 asus k53s with nvidia gforce I need these to do my work. I tried the umblebee fix, and just removing all nvidia drivers, or rolling back. I do not know why these were working then stopped, but did notice a new nvidia console in the mu which I assume was from enabling the automatic nvidia feeds, etc? I also played with the xorg, however have no clue what settings are valid. In addition, the display is 50% of the time not recognized now? It just gives a geeic 640x480 and I have to login and out 10 times to get it to return to a normal setting. When I try and set it manual, there is no other setting allowed from the settings menus, and the terminal changes just get re set every time I log out?

  Read the article

• How to connect to my own WiFi using Broadcom STA drivers?

  - by Chris

  I'm trying hard to switch to Linux from Windows because of my engineering project. Unfortunately, everything is against that change! Before I have installed Broadcom STA proprietary drivers, I was seeing on NetworkManager and nm-applet only local radio-internet-access networks. After I installed Broadcom STA, I see my neighbor's wireless network (channel 11, WEP) Neither before nor after the installation is own wireless network available. Computer: Asus Lamborghini VX6 Ubuntu: 12.04 LTS 64-bit Router: ASUS N55U (A1) with newest AsusWRT firmware Network: Channel 5 (tried also 10 and 11, both on 20 and 40MHz bands), WPA2 Personal, 2,4 + 5 GHz (what is not very important, 'cause the wlan card in VX6 is only 2,4GHz). Network works fine on Windows, also through D-Link repeater on the other floor. Unfortunately, same network is invisible to Ubuntu on same machine. I have tried some combinations with other GUIs but it did not work. Are there any better drivers for Ubuntu? I need that network badly, but I'm an Ubuntu newbie, so I don't know how to solve that problem. Please help.

  Read the article

• I can't get grub menu to show up during boot

  - by wim

  After trying (and failing) to install better ATI drivers in 11.10, I've somehow lost my grub menu at boot time. The screen does change to the familiar purple colour, but instead of a list of boot options it's just blank solid colour, and then disappears quickly and boots into the default entry normally. How can I get the bootloader back? I've tried sudo update-grub and also various different combinations of resolutions and colour depths in startupmanager application with no success (640x480, 1024x768, 1600x1200, 16 bits, 8 bits, 10 second delay, 7 second delay, 2 second delay...) edit: I have already tried holding down Shift during bootup and it does not seem to change the behaviour. I get the message "GRUB Loading" in the terminal, but then the place where the grub menu normally appears I get a solid blank magenta screen for a while. Here are the contents of /etc/default/grub # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX=" vga=798 splash" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

  Read the article

• Nvidia GeForce Gt-520M-cn on intel dh61ww Ubuntu 12.04

  - by j goseeped

  hi people i hope you can help a little bit , i appreciate your time look: i have a this desktop i7 2600, 8gb ram ddr3, board intel dh61ww, Geforce Nvidia GT520-cn 2Gb ddr3, i just install ubuntu 64bits 12.04 kernel 3.2.0-23-generic , i want to setup two monitors samsung led 22" and get start mi video card 1) i download and installed nvidia driver 295.59 and also try with 302.17 to apt-update and upgrade, apt-get install build-essential linux-headers-$(uname -r), apt-get remove --purge nvidia*, apt-get remove --purge xserver-xorg-video-nouveau, vim /etc/modprobe.d/blacklist.conf blacklist vga16fb blacklist nouveau blacklist rivafb blacklist nvidiafb blacklist rivatv sh NVIDIA.run, sudo service lightdm start, reboot, nvidia-xorgconf 2)after reboot i get 800x600 and nvidia-settings say this. You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run nvidia-xconfig as root), and restart the X server. 3) i change a little bit xorg.conf to set up a resolution to work property 4) i dont have any image in the monito and i dont have any option on Nvidia X server settings lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520] (rev a1) egrep -i 'glx|nvidia' /var/log/Xorg.0.log [ 12.005] (II) LoadModule: "glx" [ 12.005] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 12.575] (II) Module glx: vendor="NVIDIA Corporation" [ 12.585] (II) NVIDIA GLX Module 302.17 Tue Jun 12 16:22:45 PDT 2012 [ 12.585] (II) Loading extension GLX [ 13.037] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event9) glxinfo | grep direct Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig sorry my english is no very well. and thanks guys

  Read the article

• OpenGL doesn't draw (3.3+) [on hold]

  - by Dhiego Magalhães

  Brief: I've been following this tutorial about OpenGL for 2 days, and I still can't have a triangle drawn, so I'm asking for help here. The tutorial is turned to OpenGL version 3.3 programing, using vertex arrays, buffers, etc. The libraries are: GLFW3 and GLEW, and I setted them by myself. The screen keeps black all the time. Full code: link here (It's just like a Hello World opengl program) Further Details: I get no errors at all. I downloaded a software to test my video card, and it supports OpenGL 4.1+ Standard OpenGL code for drawing (from earlier version) such as this one works normally. I'm using Microsoft Visual Studio 10.0 I presume all the OpenGL implementation was dune right: I added Additional Dependences to the linker as glew32.lib, opengl32.lib, glfw3.lib. The glew.dll was placed at SysWOW64 - because I'm running window 64bits, and glew is 32. Notes: I've been working hard to find out what this is, but I can't find. I would appreciate if anyone could test this code for me, so I can know if I implemented something wrong, and that its not my code.

  Read the article

• How do I debug xorg/fglrx related system freezes on Ubuntu 12.10?

  - by racerror

  My brand new system is randomly freezing and I don't know how to debug the issue. System: AMD A10-5800k Asus F2A85-M motherboard Integrated Radeon HD 7660D 8gb Samsung ddr3 1600 Ubuntu 12.10 Gnome shell / Unity (issue exists in both) xorg.conf (relevant parts): Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:0:1:0" Option "TexturedVideoSync" "on" Option "UseFastTLS" "2" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "Monitor0" DefaultDepth 24 Option "UseEDID" "False" Option "ExactModeTimingsDVI" "True" Option "NoBandWidthTest" "true" Option "ModeValidation" "AllowNon60hzmodesDFPModes, NoEDIDDFPMaxSizeCheck, NoVertRefreshCheck, NoHorizSyncCheck, NoDFPNativeResolutionCheck, NoMaxSizeCheck, NoMaxPClkCheck, NoEDIDModes" Option "UseEDIDDPI" "False" Option "UseEDIDFreqs" "0" Option "NoLogo" "True" Option "Coolbits" "1" Option "metamodes" "DFP-0: 2560x1440_60 +0+0" SubSection "Display" Depth 24 Modes "2560x1440" EndSubSection I ran memtest on my ram and it checks out fine. I have tried using the latest fglrx and fglrx-beta. I have loaded 3.6.x kernel. I do not see anything relevant in dmesg, kern.log, syslog, .xsession-errors or Xorg.log. I cannot ssh into the machine when frozen from another machine. I know that system resources not being stressed when the crashes happen. It seems that video and any gaming (very simple graphics games) contribute to the freezes most frequently. However, I have experienced the crash before when just using Chrome. I suspect the crashes are xorg/fglrx related, but I have no evidence to back that up. Where should I look? What should I grep for? What should I try next?

  Read the article

• How can I fix my xvinfo?

  - by YumYumYum

  How can i fix my X server/driver? $ xvinfo X-Video Extension version 2.2 screen #0 no adaptors present Additional info: $ uname -a Linux desktop 2.6.32-33-generic #70-Ubuntu SMP Thu Jul 7 21:13:52 UTC 2011 x86_64 GNU/Linux $ lspci 00:00.0 Host bridge: Intel Corporation Device 0100 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 1503 (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4a (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8892 (rev 10) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) Follow up: It seems in 64-bit its a mess doing existing approach. Therefore, after upgrading to 12.04 64-bit this problems in same hardware is resolved (of-course, i have now other drivers problem)

  Read the article

• To sell or give for free

  - by QAH

  Hello everyone! I am currently making a game that I was originally planning to sell. It is a simple 2D arcade style game for the PC. I've seen many indie games become popular and generate revenue from advertisements, but the game itself remains free. I need some advice on whether or not I should sell my game, release it for free with advertisements, or ask for donations and keep the game free. I feel that my game is fun, but of course the graphics aren't tip top because I am a programmer, not an artist. I just take screenshots of 3D models I get from Turbosquid and crop around it to make a sprite. Also, and I could be very wrong about this, it seems that there are more legal issues surrounding selling a game than making it free and generating revenue from advertisement, or asking for donations. If I am wrong, someone please correct me. Also, I am very interested in generating some revenue for my work, but that isn't at the very top of my list. I am in my last year of high school, soon to be going to college, and I am going to major in computer science/software engineering. So I am trying to gain some preliminary experience at home by coding stuff every day. One way of getting this experience is by making this game. So what do you think? What route should I take? What has worked well with other indie games? Thanks in advance.

  Read the article

• radeon display driver clones monitors while using Xinerama

  - by gregmuellegger

  I'm trying to get my two Radeon HD 4770 cards working with three monitors. Xinerama works so far in the way that I have two fully working monitors were I can move windows from one to the other. My problem now is that my third monitor is a clone of my second monitor (displaying the exact same thing). These monitors are connected to the same graphic card ("Screen Middle" and "Screen Right" in the xorg.conf below). Here is my xorg.conf: Section "ServerLayout" Identifier "ThreeMonitors" Screen "Screen Left" 0 0 Screen "Screen Middle" RightOf "Screen Left" Screen "Screen Right" RightOf "Screen Middle" Option "Xinerama" EndSection Section "Monitor" Identifier "Monitor Left" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Middle" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Right" Option "DPMS" EndSection Section "Device" Identifier "Device Left" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:3:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Left" Device "Device Left" Monitor "Monitor Left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Middle" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Middle" Device "Device Middle" Monitor "Monitor Middle" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Right" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:1" Screen 1 EndSection Section "Screen" Identifier "Screen Right" Device "Device Right" Monitor "Monitor Right" SubSection "Display" Depth 24 EndSubSection EndSection I'm using a fresh Kubuntu 10.10 installation with propsed-updates enabled since this repo contains a xorg fix for using multiple graphic cards. I hope someone can help me out. Very many thanks!!

  Read the article

• why doesn't my computer resume after sleeping overnight?

  - by bamdad

  i'm having a weird, weird bug that's been haunting me since 11.10. if i listen to music or watch a video and my computer automatically goes to sleep at night, it won't properly resume in the morning. otherwise, suspend and resume works just fine. what happens is that the wi-fi and bluetooth indicator (that turns from white to orange when suspending) stays orange, the display doesn't turn on, and the only option i have is to hard reset the machine. here's what i've tried so far: installing (and uninstalling and reinstalling) laptop-mode-tools switching the proprietary wireless driver (broadcom-wl) to the open source one (brcmsmac & bcma) and back unloading (and blacklisting) all bluetooth modules (rfcomm, btusb, bnep, bluetooth) and stopping (# stop bluetooth) and disabling (# echo 'manual' /etc/init/bluetooth.override) the bluetooth service creating a custom pm sleep action as suggested here: http://ubuntuforums.org/showthread.php?p=11926504 not watching youtube / any stuff that uses flash before going to sleep (i have flashblock, and i checked $ ps aux | grep flash) because i suspected flash to be the culprit trying out different versions of fglrx (the one from the repos, then installing the latest one from amd's site via generated .deb files, then back to the official ones) none of these worked. i remember back in the days of 10.04, there was a gconf key called network sleep: i thought about disabling that, since re-enabling the wireless card seems to be the problem (according to the indicator led), but the option appears to be missing from gnome 3 (unity-2d, whatever). does anyone have any ideas? thanks, bamdad

  Read the article

• Banshee doesn't like opening websites

  - by Allan

  I have come across two bugs (which will be added to launchpad if it's not resolved here) When I open any of the websites in Banshee Amazon or Miro Guide as soon as the site is finished loading it crashes Banshee. If I play any video local or remote it will show 1 frame maybe 0.5 sec of video then I get a black screen and audio continues in the backgound. Specs & Details I have a Fujitsu Amilo 1718 laptop with 2 gig of ram (original 1 gig) graphics is provided by ATI Radeon Xpress 200M (don't laugh it works with compiz....just) I have a link to the output of banshee --debug Here Don't have time to read? Here are the Highlights [2 Warn 11:52:34.814] Caught an exception - System.ArgumentNullException: Argument cannot be null. then abit later Debug info from gdb: Could not attach to process. If your uid matches the uid of the target process, check the setting of /proc/sys/kernel/yama/ptrace_scope, or try again as the root user. For more details, see /etc/sysctl.d/10-ptrace.conf ptrace: Operation not permitted. ================================================================= Got a SIGSEGV while executing native code. This usually indicates a fatal error in the mono runtime or one of the native libraries used by your application. ================================================================= Aborted Not music to my ears as you can expect. The version I am using is 1.9.4 from the daily ppa but these bugs happen in any version of banshee from 1.8.1 and up. So if any one has come across a fix for this problem please share!! additional info Both VLC and Miro work on my system so there isn't a system wide problem with video and I haven't mentioned mono so no trolling it will get voted down.

  Read the article

• Matrices: Arrays or separate member variables?

  - by bjz

  I'm teaching myself 3D maths and in the process building my own rudimentary engine (of sorts). I was wondering what would be the best way to structure my matrix class. There are a few options: Separate member variables: struct Mat4 { float m11, m12, m13, m14, m21, m22, m23, m24, m31, m32, m33, m34, m41, m42, m43, m44; // methods } A multi-dimensional array: struct Mat4 { float[4][4] m; // methods } An array of vectors struct Mat4 { Vec4[4] m; // methods } I'm guessing there would be positives and negatives to each. From 3D Math Primer for Graphics and Game Development, 2nd Edition p.155: Matrices use 1-based indices, so the first row and column are numbered 1. For example, a12 (read “a one two,” not “a twelve”) is the element in the first row, second column. Notice that this is different from programming languages such as C++ and Java, which use 0-based array indices. A matrix does not have a column 0 or row 0. This difference in indexing can cause some confusion if matrices are stored using an actual array data type. For this reason, it’s common for classes that store small, fixed size matrices of the type used for geometric purposes to give each element its own named member variable, such as float a11, instead of using the language’s native array support with something like float elem[3][3]. So that's one vote for method one. Is this really the accepted way to do things? It seems rather unwieldy if the only benefit would be sticking with the conventional math notation.

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• How do I install the nvidia driver for a GeForce 9300M?

  - by Alex

  Yesterday i've installed ubuntu 11.04 (instead of 10.10). And i need to install nvidia driver which supports opengl 3.3 In 10.10 i did it in a such way: Ctrl+alt+f1 login sudo /etc/init.d/gdm stop sudo sh driver.run startx Not it doesn't work. Because ctrl+alt+f1 doesn't show login screen. Just only black screen. I've googled this problem. Some people have it but no one knows how to solve. Sometimes people say that it is connected with video card or driver. But i have GeForce 9300M G, and i've activated a standard driver. Anyway, it worked in 10.10, but doesn't work now. The main problem is that i need to kill xserver to install this driver. killing the process just only restarts xserver. Also, I've tried to /etc/init.d/gdm stop in GUI-console. It says that "Fake initctl,doing nothing". Google didn't helped in this case too. Any ideas to install that driver?

  Read the article

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >