Search Results

Search found 24766 results on 991 pages for 'information retrieval'.

Page 768/991 | < Previous Page | 764 765 766 767 768 769 770 771 772 773 774 775  | Next Page >

• Reusing Raid 5 Drive?

  - by User125

  We have two servers (ML530 G2 and DL380G2) w/ identical HP 10K RPM SCSI drives w/ a raid 5. One is decommissioned and the other will be decommissioned shortly. However, one of the drives on the production server had a drive failure. My hope was to take one of the drives from the decommissioned server and pop it into the production server. Both are running RAID 5. I broke the array on the decomm. server. To my knowledge, that should have wiped out all the volume and partition information. However, I do not know if it is safe to then take a drive from the decomm'ed server and replace the failed drive. Will the existing array see it as a replacement drive, wipe it and rebuild? Or will it fail because it was used in an array before. Are there any remnant data that resides on the drives after deleting a raid 5 array? These servers are 10-15 years old, so we're just trying to keep them alive until we decommission it. I'm not looking to pay a premium to find a vendor that still sells replacement drives for this system.

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

• Restoring MBR, partition table, and boot sector of memory card without data loss ("USBC")

  - by Synetech

  Abstract I have a FAT32 memory card that when inserted into a computer causes Windows to prompt to format it. The card is definitely not supposed to be blank and has a bunch of files on it. Symptoms Using a hex-editor/disk-viewer, I examined the card and found that several sectors/clusters have been overwritten with something that has a signature of USBC at the start of the sector. Specifically, the master boot record (and partition table) is gone (hence Windows thinking the card is blank and needing to be formatted), as are the boot sectors (they have the USBC signature and a volume label of NO NAME and partition type of FAT32). Fortunately, it looks like both copies of the FAT are almost entirely intact (a few FAT entries at the start of a cluster here and there seem to be overwritten by USBC). The root directory is also nearly intact—I can see the volume label entry and subdirectory listings, but one sector is overwritten. (There are no more instances of USBC after the last one in the FAT2.) Hypothesis These observations seem to indicate some sort of virus that erases a few key filesystem structures, and then overwrites a few extra sectors here and there. Googling it seems to corroborate the idea of a virus, except that others report a file called USBC which does not apply here, and in fact, could not be possible since there is no filesystem to even see files. I cannot find any information about a virus with these symptoms, nor a removal tool. (I can't help but wonder if it is actually due to an autorun virus prevention tool.) Question I can likely fix the FAT corruption since they are mostly contiguous chains and maybe even the lost sector of the root directory, but does anyone know of a convenient way to restore or (re)create the MBR/partition table and boot sectors (without formatting or overwriting the data)?

  Read the article

• How to get just value from database query in Excel?

  - by Corin

  I'm creating a spreadsheet as a collection point of information from a number of MS Access databases. I will run a query on each database to get a count of records in a particular table. Each database has the same structure but different content as they are used in different situations. So the query returns a single value, rec_count. I've figured out how to create that query, save it and then use it as the data source. So far so good. The problem is that Excel treats the query results as a table. So instead of getting just the single value the query returns, I also get the field name. Thus the result takes up two cells instead of one. When linking in the data source, I only see Table, PivotTable Report and PivotChart as options for viewing the data. I don't want any of those. I just want the single value without any formatting, column headers, etc. Is there a way to do this is Excel 2007?

  Read the article

• Apache: getting proxy, rewrite, and SSL to play nice

  - by Rich M

  Hi, I'm having loads of trouble trying to integrate proxy, rewrite, and SSL altogether in Apache 2. A brief history, my application runs on port 8080 and before adding SSL, I used proxy to strip the 8080 from the url's to and from the server. So instead of www.example.com:8080/myapp, the client app accessed everything via www.example.com/myapp Here was the conf the accomplished this: ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> ProxyPass /myapp http://www.example.com:8080/myapp ProxyPassReverse /myapp http://www.example.com:8080/myapp What I'm trying to do now is force all requests to myapp to be HTTPS, and then have those SSL requests follow the same proxy rules that strip out the port number as my application used to. Simply changing the ports 8080 to 8443 in the ProxyPass lines does not accomplish this. Unfortunately I'm not an expert in Apache, and my skills of trial and error are already reaching the end of the line. RewriteEngine On RewriteCond %{HTTPS} off RewriteRule myapp/* https://%{HTTP_HOST}%{REQUEST_URI} ProxyRequests Off <Proxy */myapp> Order deny,allow Allow from all </Proxy> SSLProxyEngine on ProxyPass /myapp https://www.example.com:8443/mloyalty ProxyPassReverse /myapp https://www.example.com:8433/mloyalty As this stands, a request to anything on the server other than /myapp load fine with http. If I make a browser http request to /mypp it then redirects to https:// www.example.com:8443/myapp , which is not the desired behavior. Links within the application then resolve to https:// www.example.com/myapp/linkedPage , which is desirable. Browser requests (http and https) to anything one level beyond just /myapp ie. /myapp/mycontext resolve to https:// www.example.com/myapp/mycontext without the port. I'm not sure what other information there is for me to give, but I think my goals should be clear.

  Read the article

• Export files to remote server using TortoiseSVN

  - by Matt

  Hi, I'm using TortoiseSVN to keep revisions of my code. When I commit changes, I take note of what files have changed and upload them to my server using FTP. Here's my workflow: Edit files on local computer (eg. files in C:\Users\Me\web) Commit changes to local repository using rightclick- TortoiseSVN- SVN Commit. Take the files, open FileZilla (FTP client) and upload the files to a remote server. I was wondering if there was a way in which I could omit step 3 from my workflow. Basically I would like the changed files to be automatically uploaded to the remote server when I commit a version to the repository. Information about my computer environment: Windows 7 Ultimate x64 with TortoiseSVN x64 Notepad++ text editor Files edited are PHP, CSS, JS, HTML, etc. Server is running Linux with PHP 5.2 and MySQL. FileZilla is used to upload files. I can connect to the server via SSH if that is needed. Thank you in advance.

  Read the article

• Relevance and Necessity of SNMP

  - by Adam Tannon

  Edit: I am in the process of designing a Java-based monitoring tool that will send back periodic "health checks" of a Java app deployed to a cluster of GlassFish servers. I am trying to figure out the best protocol for this monitoring tool to send information back to the monitoring server on. After an initial research effort on my part, it seems like SNMP is just a protocol for monitor-type applications to communicate the "health status" of something (a part of a network, a server, a cluster, an application, etc.) to the rest of the network. If the above is incorrect, please correct me!!! Assuming the generalization is more or less accurate, my next question is: why is this a protocol!?!? In the age of REST/SOAP/TCP protocols, why is there the need for a standardized protocol that only fits one type of application (monitoring)? In other words, if I'm a developer assigned to building a new monitoring tool that periodically polls a server and reports on its CPU and available memory, what advantages does SNMP give me over just POSTing to a RESTful API via plain 'ole HTTP? I'm sure I'm missing something here - I just need someone to help connect the dots! Thanks in advance!

  Read the article

• USB-to-Serial showing gibberish at 115200 Baud

  - by Mose

  I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

  Read the article

• Viability of Mac OS X 10.9 Time Machine Server in office environment

  - by user197609

  Currently we have about 20 Mac OS 10.9 MacBook Pros (almost all with SSDs) backing up to individual USB drives. I'd like to consolidate these to one drobo thunderbolt drive array attached to a Mac Mini server (running 10.9 server) using time machine server. My question is, will this scale to 20 users? Examples I have seen seem to be 5 or 6 users tops, and this isn't easy for me to test (I'd rather not ask everyone to backup to the array and then switch back to USB drives if it brings our network to its knees). My primary concern is saturating our gigabit network, as time machine backs up every hour for every machine, so there would usually be a couple people backing up at any given time. We also have some people occasionally on our 802.11ac network and not on ethernet (usually connected via 802.11n until people upgrade to newer machines), but most of the time people are connected to our thunderbolt displays which have a gigabit ethernet connection on them. Our network topology is one 32 port gigabit switch with 5 smaller gigabit switches at each desk cluster. The mac mini server is connected directly to the top level switch. Update: Failing information from someone who has done this in practice, I suppose my question is really around how switches work. If three or four people are backing up simultaneously, and then other two (different) users transfer a file between each other, will they be able to transfer the file at gigabit speeds?

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Windows Server doesn't connect to a network share

  - by Dmitriy N. Laykom

  Windows Server doesn't connect to a network share. Network share is working. Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When I connected the network share I observed this error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location The network share was mounted via Group Policy. Perchance anyone knows how I can avoid this error? When the OS has been restored from the disk problem has been solved

  Read the article

• Will a SQL Server client alias survive a sysprep?

  - by shufler

  I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

  Read the article

• disk write cache buffer and separate power supply

  - by HugoRune

  Windows has a setting to turn off the write-cache buffer (see image) Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. Is it feasible and economical to get such a "separate power supply" for the internal sata drives of a non-server PC? Under what name is such a power supply sold? I know that there are UPS devices that can be connected to external drives,but what is required to be able to switch this setting safely on for an internal disk? The setting has different descriptions in different version of windows Windows XP: Enable write caching on the disk This setting enables write caching in Windows to improve disk performance, but a power outage or equipment failure might result in data loss or corruption. Windows Server 2003: Enable write caching on the disk Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows Vista: Enable advanced performance Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows 7 and 8: Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. This article by Raymond Chen has some more detailed information about what the setting does.

  Read the article

• 2 routers at home- how to connect with VNC?

  - by Charles Leviton

  I have two routers at home. First router is upstairs and is connected to the cable modem. 2nd router is downstairs and acts as "signal booster" for the 1st router. Devices connected to the upstairs router have IP addresses of the form 192.168.1.n Devices connected to the upstairs router have IP addresses of the form 192.168.2.n. I blindly followed instructions from a website to do this set up, just glad it works! Upstairs I have a PC running Win 7 64 bit. Its assigned IP is 192.168.1.7. I have a VNC viewer running on this. Downstairs I have a 2nd PC running Vista 32 Home edition bit that is connected to the 2nd router and has IP Address 192.168.2.114. VNC server is running on this. It's listening on 5900. There is no firewall. When I try to connect to this downstairs PC from upstairs it fails with message "Failed to connect to server". I cannot ping to this either. If I try to connect to this downstairs PC using VNC Viewer from another computer that's connected to the same downstairs router then it works like a charm. So what's the work around if the viewer is on a different "network"? I don't have any problems doing remote desktop connection from the downstairs PC to the upstairs PC even if they are connected to different routers. Router information- Upstairs- ASUS RTN13U, downstairs- DD-WRT v24 RC-5 Thanks! P.S. I posted this on the Ultra VNC forum as well but that doesn't seem to have a lot of activity, so taking the liberty to multipost.

  Read the article

• How to copy a floppy boot disk?

  - by Sammy

  I have a floppy boot disk and I would like to copy it to preserve it, as a backup. If I have two floppy drives, A and B, how can I copy the disk? Assuming one has two floppy drives Can I simply insert the floppy disk in one of the drives and then an empty floppy disk in the other and issue a simple command like this one. A:\>copy . b: Will this only copy the contents of the current directory and none of the files in subdirectories? Do I have to explicitly specify the option to copy everything? Also, what about the boot information? That won't get copied, right? If one has only one floppy drive... How do you copy a floppy disk if you only have one floppy drive? Do you in fact have to copy its contents to the local hard drive C and then copy that to an empty floppy disk using the same floppy drive? A:\>copy . c:\floppydisk A:\> A:\>c: C:\> C:\>copy floppydisk a: C:\> I'm guessing I will need some type of disk image tool to really copy everything on a bootable floppy disk. Something like the dd command on Linux perhaps? Am I right?

  Read the article

• Nokia E75 Mail for Exchange

  - by Sebastian

  Hi, I have a SBS2003 runing Exchange Server 2003 SP2. My OWA has a godaddy certificate valid for 3 years to come installed. HTTPS works fine for OWA. The certificate has also been copied into the Nokia E95 I am trying to syncronize my Nokia E75 via Mail for Exchange to my mail account on the Exchange server. These are the steps i use: Menu Email New Start Select Internet Gateway Than i enter the details: [email protected] I select company email Mail for Exchange In the domain menu i enter : mydomain In the username/password menu i enter : myusername/mypassword In the server menu i enter : mail.mydomain.com (where the DNS resolves into the server's IP address) In the secure access i select : Internet / Secure / 443 NOTE : port 443 has been opened on my SBOX and forwarded to the exchange server. On IIS default website properties directory security secure communications edit the "Require Secure Channel SSL" is enabled. However, when i try to sync my phone i get the following error code: * Mail for Exch permissions illegal. Check permission configuration. * The phone log gives the following information : Username or Password Illegal. Correct Username and/or Password in the profile options. I've tried speaking with the Phone service support but they cannot identify the problem. Any help will be much apreciated.

  Read the article

• Possible disk IO issue

  - by Tim Meers

  I've been trying to really figure out what my IOPS are on my DB server array and see if it's just too much. The array is four 72.6gb 15k rpm drives in RAID 5. To calculate IOPS for RAID 5 the following formula is used: (reads + (4 * Writes)) / Number of disks = total IOPS. The formula is from MSDN. I also want to calculate the Avg Queue Length but I'm not sure where they are getting the formula from, but i think it reads on that page as avg que length/number of disks = actual queue. To populate that formula I used the perfmon to gather the needed information. I came up with this, under normal production load: (873.982 + (4 * 28.999)) / 4 = 247.495. Also the disk queue lengh of 14.454/4 = 3.614. So to the question, am I wrong in thinking this array has a very high disk IO? Edit I got the chance to review it again this morning under normal/high load. This time with even bigger numbers and IOPS in excess of 600 for about 5 minutes then it died down again. But I also took a look at the Avg sec/Transfer, %Disk Time, and %Idle Time. These number were taken when the reads/writes per sec were only 332.997/17.999 respectively. %Disk Time: 219.436 %Idle Time: 0.300 Avg Disk Queue Length: 2.194 Avg Disk sec/Transfer: 0.006 Pages/sec: 2927.802 % Processor Time: 21.877 Edit (again) Looks like I have that issue solved. Thanks for the help. Also for a pretty slick parser I found this: http://pal.codeplex.com/ It works pretty well for breaking down the data into something usable.

  Read the article

• What is the correct approach i should use for an application that requires amazon S3 uploads and SimpleDB data management?

  - by Luis Oscar

  I am developing an application for iOS and that is going smoothly, the problem is that I am very new at server sided things. I am totally confused about how to correctly use Amazon Web Services for this purpose. What I want to do is very simple. I want my application to be able to query a servlet hosted in EC2 to be able to retrieve pictures and data based on some criteria from S3 and SImpleDB respectively. Also the application should be able to upload pictures into a S3 bucket and register the information in the SImpleDB. My main concerns are security and costs, So far i was using Amazon Token Vending Machine but I haven't been successful when trying to customize it, and while researching I discovered that on the long run it is very expensive. The ultimate goal is to handle a "social" picture service for my iOS application. Being able to register new users, authenticate these users. See what permissions they have to which pictures from the bucked. And all this without having to worry about Third party people from accessing the private pictures of my users. Sorry for this question but I am really clueless about how to handle this... I have tried reading many articles but all these server stuff looks very scary.

  Read the article

• Mail-Merge on Steroids: Can Word 2003 do this?

  - by richardtallent

  I have a huge report to put together, made up of over 1,000 smaller, nearly-identical reports. Each report includes: General 1:1 information (basic mail-merge stuff) Lots of text, some of which may need to be disabled or have alternate text based on a boolean field. A few embedded images, preferably loaded via HTTP URL, but if they have to be on the a file system thing I can do that. (Filenames will be provided as a field in the data source.) Fortunately, all images are roughly the same size/shape. Several 1:m tables with a few fields apiece. The kicker is the master/child tables. I've seen examples for Word 2000 for doing this by left-joining the master and child table and using some IF/THEN logic to know whether to jump to the next master record. But in my case, I have several of these subtables, so that approach won't really work. So, can Word 2003 handle arbitrary master/child tables? If so, how? If not, I considered InfoPath, but I haven't used it before, and it seems to be made for data entry, not long formatted reports. I'm a software developer, so I could always hack something together with a massive VBA macro, or generating the report in HTML on the web server (where the data is coming from anyway). But I'm hoping Word will work without such gymnastics, since it will give the ultimate users of the report template better control over formatting and making minor changes.

  Read the article

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Reverse SSH tunnel: how can I send my port number to the server?

  - by Tom

  I have two machines, Client and Server. Client (who is behind a corporate firewall) opens a reverse SSH tunnel to Server, which has a publicly-accessible IP address, using this command: ssh -nNT -R0:localhost:2222 [email protected] In OpenSSH 5.3+, the 0 occurring just after the -R means "pick an available port" rather than explicitly calling for one. The reason I'm doing this is because I don't want to pick a port that's already in use. In truth, there are actually many Clients out there that need to set up similar tunnels. The problem at this point is that the server does not know which Client is which. If we want to connect back to one of these Clients (via localhost) then how do we know which port refers to which client? I'm aware that ssh reports the port number to the command line when used in the above manner. However, I'd also like to use autossh to keep the sessions alive. autossh runs its child process via fork/exec, presumably, so that the output of the actual ssh command is lost in the ether. Furthermore, I can't think of any other way to get the remote port from Client. Thus, I'm wondering if there is a way to determine this port on Server. One idea I have is to somehow use /etc/sshrc, which is supposedly a script that runs for every connection. However, I don't know how one would get the pertinent information here (perhaps the PID of the particular sshd process handling that connection?) I'd love some pointers. Thanks!

  Read the article

• DSL Connection drops

  - by user60024

  Ok, I just moved so I had to switch from Cable to DSL. I know very little about computers or internet connections and such, so I had AT&T come out to the new house to set up their highest speed. When they got here, they told me that I needed to downgrade to 3.5mbps because I was too far away. Well we did and everything was going great for two days until I started experiencing random disconnects which have been happening now for about 2 to 3 weeks. I am using a N300 Wireless Dual Band ADSL2+ Modem Router and my ethernet cable is hooked directly into my computer from it. I recently started to notice that it disconnects around 5:30 and 8:30, which may be because a lot of people are on their computers(?) and that it works perfectly fine, almost, all the time if I'm not playing a game. During this time, when I try to load up World of Warcraft the Internet light disappears and the DSL light begins blinking. (So maybe it's too much for the modem and it resets?) Other than that it is amazing, but I'd like to try and fix some of these problems. If you need more information, let me know on how to get it for you and what to do. Thanks for the help!

  Read the article

• PHP unable to allocate memory.

  - by AlReece45

  On my way to the office this morning, every website on our shared VPS started giving the same error (several times, not the typical memory_limit error which is fatal): Warning: Unknown: Unable to allocate memory for pool. in Unknown on line 0 The shared server is a 64-bit OpenVZ container running cPanel. There are only ~6 VPSes on the host-- this is the largest one at only 4GB. The host itself has 24GB RAM. As the below graphs show, the memory usage on the host and VPS are both rather low. CPU Usage/Disk/Host all seem to be normal. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. Apache 2.2, PHP 5.2 (mod_php) Restarting Apache has corrected the problem for now. However, I'd like to prevent it from happening again and I'm not sure what was limiting the memory. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. There's seems to be plenty of memory: what caused this error? VPS Memory Usage Host Memory Usage APC Information apc.ttl=0 apc.shm_size=0 apc.mmap_file_mask=(blank) 1 Segment(s) with 32.0 MBytes (mmap memory, pthread mutex locking)

  Read the article

• email attachments [closed]

  - by Alan Doolan

  My company currently use software on a local machine that will take an email from the email server, extract the attachment, rename it and then add it to a folder on a webserver using ftp. This works well but they are currently asking if it can be done 'in the cloud' or what they really mean, not local. Is there any thing that would do this on the server itself? I should clarify a bit. The attachements are various reports that are being sent to different email addresses (mostly google corporate and free accounts). We need the reports to be on a folder on a webserver so that internal pages can take the information in the reports (csv) and use it on the webpages or adds them to a separate database. The key part being that the files need to be in the particular folders. Though it does work to have a computer running software that will take the files, renames them to the required name and uploads them to the folder it relies too heavily on one computer working all the time. This is not something we can depend on at this point. I'll be honest, I'm a web developer and not strong with server systems past my particular standard requirements so this is beyond me. though yes, I am aware that my boss is not 100% sure what 'cloud' means but likes the word.

  Read the article

• Group Policy - Published software not upgrading

  - by VokinLoksar

  I'm testing this with mercurial MSIs, but it's the same for other packages. I've created a new group policy and added an old version of mercurial to User software installation as a Published package. On a Windows 7 client I install the package through Programs and Features. The installation works fine. Now, I would like to publish an updated version of mercurial. I create a new Published package. Under 'Upgrades' I configure it to replace (upgrade also doesn't work) the old version and mark this upgrade as 'Required'. The old package is not removed. The Windows 7 client is then restarted. When I log back in, I see a status message saying something like 'Removing managed software Mercurial ...'. There is no message about installation of the upgrade. If I look in Programs and Features, I can see the new version of mercurial listed. However, the actual mercurial directory under Program Files is missing. It's as though the installation recorded information about the MSI, but didn't actually install anything after removing the old version. As I mentioned, this isn't specific to mercurial. I've tried using other apps and have yet to find one that can be upgraded via a Published package. Using Assigned packages in Computer Configuration works without problems, but I would like this software to be optional rather than required. Ideas?

  Read the article

< Previous Page | 764 765 766 767 768 769 770 771 772 773 774 775  | Next Page >