Search Results

Search found 15160 results on 607 pages for 'boot disk'.

Page 325/607 | < Previous Page | 321 322 323 324 325 326 327 328 329 330 331 332  | Next Page >

• Since upgrading to Windows 8.1, I can't open any files on a SMB share shared by my OS X Mavericks Mac

  - by Gary

  I have a PC with Windows 8.1 and a Mac with Mavericks. I have a folder on the Mac that is shared with the PC. When I'm on the PC and I try to open a file that is shared by the Mac, such as an ISO file (a disk image), then I get a message saying that I cannot open the file, or the file is in use (it depends on the app/filetype). I have the same problem when I open a video file. Strangely, text files and PDF files are just fine. And if I copy any of the problematic files to the local Windows disk, then I can open them just fine. The specific error messages are: AVI files opened in VLC: "Your input can't be opened. VLC is unable to open the MRL." ISO files opened by Windows Explorer: "Sorry, there was a problem mounting the file." This only started happening after I upgraded to Windows 8.1 on the PC and Mavericks on the Mac. Mavericks upgraded its SMB version from SMB1 to SMB2, so perhaps that is related? Does anyone know what the problem might be, and how I could fix it? Thanks in advance!

  Read the article

• wrt54gl reboots; troubleshooting steps?

  - by Bill

  I am using about 10 wrt54gl's in a small school. I am using a combination of stock firmware and Tomato 1.25, slowly moving towards all Tomato. We have had these devices installed for several years without problems. Recently, more and more of the units have started to spontaneously reboot, usually during high-traffic times (but not always). For the most part, the rebooting is not critical for us, but the wrt54gl's temporarily revert to 192.168.1.1 on the LAN ethernet ports and conflict with a critical server that's already installed with that IP. (Yes -- we plan to move the server off that address, but it is an involved process.) Both Tomato and the stock firmware (several versions from recent to several years old) exhibit the same problem: random reboots and reverting to 192.168.1.1 and conflicting temporarily with our server until the firmware boot process finishes. Here are my questions: Any way to prevent the wrt54gl's from reverting to 192.168.1.1 during the boot process? I was thinking of doing a custom firmware mod, although I hate to go that direction. Any steps to take in troubleshooting the reboots? Only some of the wrt54gl's reboot, which is odd. Others stay online for weeks and months without issues. Thanks.

  Read the article

• Redis 2.0.3 would not let go of deleted appendonly.aof file after BGREWRITEAOF

  - by Alexander Gladysh

  Ubuntu 10.04.2, Redis 2.0.3 (more details at the end of the question). My AOF file for Redis is getting too large, to the point where it soon would threaten to take whole free disk space on my small-HDD VPS box: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda 32G 24G 6.7G 78% / $ ls -la total 3866688 drwxr-xr-x 2 redis redis 4096 2011-03-02 00:11 . drwxr-xr-x 29 root root 4096 2011-01-24 15:58 .. -rw-r----- 1 redis redis 3923246988 2011-03-02 00:14 appendonly.aof -rw-rw---- 1 redis redis 32356467 2011-03-02 00:11 dump.rdb When I run BGREWRITEAOF, the AOF file shrinks, but disk space is not freed: $ ls -la total 95440 drwxr-xr-x 2 redis redis 4096 2011-03-02 00:17 . drwxr-xr-x 29 root root 4096 2011-01-24 15:58 .. -rw-rw---- 1 redis redis 65137639 2011-03-02 00:17 appendonly.aof -rw-rw---- 1 redis redis 32476167 2011-03-02 00:17 dump.rdb $ df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda 32G 24G 6.7G 78% / Sure enough, Redis is still holding the deleted file: $ sudo lsof -p6916 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME ... redis-ser 6916 redis 7r REG 202,0 3923957317 918129 /var/lib/redis/appendonly.aof (deleted) ... redis-ser 6916 redis 10w REG 202,0 66952615 917507 /var/lib/redis/appendonly.aof ... How can I workaround this issue? I can restart Redis this time, but I would really like to avoid doing this on a regular basis. Note that I can not upgrade to 2.2 (upgrade to 2.0.4 is feasible though). More information on my system: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 10.04.2 LTS Release: 10.04 Codename: lucid $ uname -a Linux my.box 2.6.32.16-linode28 #1 SMP Sun Jul 25 21:32:42 UTC 2010 i686 GNU/Linux $ redis-cli info redis_version:2.0.3 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:32 multiplexing_api:epoll process_id:6916 uptime_in_seconds:632728 uptime_in_days:7 connected_clients:2 connected_slaves:0 blocked_clients:0 used_memory:65714632 used_memory_human:62.67M changes_since_last_save:8398 bgsave_in_progress:0 last_save_time:1299014574 bgrewriteaof_in_progress:0 total_connections_received:17 total_commands_processed:55748609 expired_keys:0 hash_max_zipmap_entries:64 hash_max_zipmap_value:512 pubsub_channels:0 pubsub_patterns:0 vm_enabled:0 role:master db0:keys=1,expires=0 db1:keys=18,expires=0

  Read the article

• Confused about the Windows 7 Preinstallation Kit

  - by David Brown

  I build custom PCs and would like to use the Windows 7 Preinstallation Kit to make installation go a little quicker and customize the Windows image. However, since each PC is built to a particular customer's specifications, the hardware will rarely be the same. So, I would like to have a single answer file that will work for everything. I'm not sure if that's possible, however. What I mostly want to do for now is add my support information as well as pre-set anything that I would normally change after each installation completes. I have a Windows 7 Professional Upgrade DVD set (both 32-bit and 64-bit), but no OEM disks. I copied the Install.wim file to my local drive and opened it in the Windows System Image Manager, but it asks me to choose a catalog file specifically for each edition of Windows 7. Will this limit the answer file to whichever edition I choose? I would think choosing Starter would give me the most basic settings, which would apply to all other editions, but I'm not entirely sure of this. I don't intend to install any extra applications or drivers. I merely want to insert an OEM disk, my OPK USB drive, and have it work for whatever edition of Windows 7 I'm installing. If a large number of similarly-configured PCs need to be built, I'll go ahead and create a custom answer file in that case, but for a single machine order, that seems like overkill. In addition, do I need a separate answer file for 32-bit and 64-bit versions of Windows 7? Or will it work for both, even though I copied the Install.wim file from the 32-bit disk? Thanks!

  Read the article

• Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

  - by leladax

  EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

  Read the article

• Setting up a dualboot by installing cloned partitions using clonezilla

  - by Nimjox

  I'm trying to setup a dual boot system where I have Windows 7 and Linux Mint. Here's the kicker both are partitions I've saved using Clonzezilla from different places and to make matters worse Linux Mint is formated as a LVM. I need both of these images specifically as windows is a corporate image that I must use and the other is a development image that took me a week to setup. I've gotten it almost all working but my issue is that I can't get clonezilla to not mess up the partition table of Windows when installing Mint or vise-vera. I can use the (-k1 option) which doens't copy the partition table but then I have a unusable partition when it clones and I'm not sure how to fix the partition table. Here's what I'm doing: Using Gparted to make partitions sda1 40GB ntfs (windows), sda2 extended 70GB, sda5 lvm2 pv 69.99 GB (Linux), sda3 500MB (GRUB) Clonezilla windows image into sda1 partition (keeping partition table) Clonezilla linux image into sda5 partition (not recreating partition table) After all that I can boot into windows using the default MBR. I can use rescue-repair cd to reinstall GRUB which will see Windows 7 but I can't get it to see the Linux OS. I'm thinking its because of the sda5 partition but I'm not sure any ideas on what I could do to get this working or where I might be going wrong. If there is any additional detail you need please let me know and I'll edit as this is a lot.

  Read the article

• Setting Up Apache as a Forward Proxy with Cahcing

  - by Karl

  I am trying to set up Apache as a forward proxy with caching, but it does not seem to be working correctly. Getting Apache working as a forward proxy was no problem, but no matter what I do it is not caching anything, to disk or memory. I already checked to make sure nothing is conflicting in the mods_enabled directory with mod_cache (ended up commenting it all out) and also I tried moving all of the caching related fields to the configuration file for mod_cache. In addition I set up logging for caching requests, but nothing is being written to those logs. Below is my Apache config, any help would be greatly appreciated!! <VIRTUALHOST *:8080> ProxyRequests On ProxyVia On #ErrorLog "/var/log/apache2/proxy-error.log" #CustomLog "/var/log/apache2/proxy-access.log" common CustomLog "/var/log/apache2/cached-requests.log" common env=cache-hit CustomLog "/var/log/apache2/uncached-requests.log" common env=cache-miss CustomLog "/var/log/apache2/revalidated-requests.log" common env=cache-revalidate CustomLog "/var/log/apache2/invalidated-requests.log" common env=cache-invalidate LogFormat "%{cache-status}e ..." # This path must be the same as the one in /etc/default/apache2 CacheRoot /var/cache/apache2/mod_disk_cache # This will also cache local documents. It usually makes more sense to # put this into the configuration for just one virtual host. CacheEnable disk / #CacheHeader on CacheDirLevels 3 CacheDirLength 5 ##<IfModule mod_mem_cache.c> # CacheEnable mem / # MCacheSize 4096 # MCacheMaxObjectCount 100 # MCacheMinObjectSize 1 # MCacheMaxObjectSize 2048 #</IfModule> <Proxy *> Order deny,allow Deny from all Allow from x.x.x.x #IP above hidden for this post <filesMatch "\.(xml|txt|html|js|css)$"> ExpiresDefault A7200 Header append Cache-Control "proxy-revalidate" </filesMatch> </Proxy> </VIRTUALHOST> Thank you once again!

  Read the article

• How do I diagnose a bottleneck in an Intel Atom based Ubuntu server?

  - by Jon Cage

  I have a small media server at home which has software raid and a gigabit link to the rest of my network. For some reason though, I only get ~10MB/s transfers when copying to/from the server. I use software RAID5 (mdadm) over 4 1TB disks. On top of that I then use LVM to give me a huge pool of disk space which is then split up into multiple partitions which can be resized as and when they need it. I'm guessing this it most likely the cause, but I'd like to know for sure where the root cause is. So, how can I benchmark network throughput (Windows 7 desktop <- Ubuntu server) and hard disk performance to try and identify where my bottleneck might be? [Edit] If anyone's interested, the motherboard is an Intel Desktop Board D945GCLF2. So that's a 300 series Atom processor with the Intel® 945GC Express Chipset [Edit2] I feel like such a fool! I just checked my desktop and I had the slower of the two onboard NICs plugged in so the server is probably not at fault here. Transferring a copy of ubuntu off the server I get ~35-40MB/s according to Windows 7. I'll do those HD tests when I get a chance though (just for completeness).

  Read the article

• SQL Server 2005 standard filegroups / files for performance on SAN

  - by Blootac

  I submitted this to stack overflow (here) but realised it should really be on serverfault. so apologies for the incorrect and duplicate posting: Ok so I've just been on a SQL Server course and we discussed the usage scenarios of multiple filegroups and files when in use over local RAID and local disks but we didn't touch SAN scenarios so my question is as follows; I currently have a 250 gig database running on SQL Server 2005 where some tables have a huge number of writes and others are fairly static. The database and all objects reside in a single file group with a single data file. The log file is also on the same volume. My interpretation is that separate data files should be used across different disks to lessen disk contention and that file groups should be used for partitioning of data. However, with a SAN you obviously don't really have the same issue of disk contention that you do with a small RAID setup (or at least we don't at the moment), and standard edition doesn't support partitioning. So in order to improve parallelism what should I do? My understanding of various Microsoft publications is that if I increase the number of data files, separate threads can act across each file separately. Which leads me to the question how many files should I have. One per core? Should I be putting tables and indexes with high levels of activity in separate file groups, each with the same number of data files as we have cores? Thank you

  Read the article

• Fedora 9 not reconizing hard drive

  - by Andrew Jones

  I am installing Fedora 9 to a PC (specifications at the bottom) and have had a lot of trouble with it recognising the hard drive. To get the Fedora installer to recognize it in the first place I had to pass "ata_generic.all_generic_ide=1 pci=nomsi" to the kernel, after which it installed OK. However, now when I boot the installed OS, I get a "could not find filesystem '/dev/root'" error. I tried passing the same arguments to the kernel at boot as I did when installing but to no avail. I have tried using the default LVM layout and defining manual ones but it made no difference. There is no option in the BIOS to enable AHCI or anything like that, in fact the BIOS is very limited in most respects. I can get into the system by using the installation CD in rescue mode (with those extra kernal parameters) but I'm not sure what to do once in there... Unfortunately using a more recent version of Fedora or even another Linux distribution altogether isn't an option becuase of outside constraints - which is annoying since I know for a fact Ubuntu works fine on this setup. I have not been using Linux that long, so treat me like an idiot - I am one. Any help would be greatly appreciated, thanks! System spec: Intel Atom Z530 CPU @ 1.6 GHz Intel US15W chipset 1 GB DDR2 160 GB SATA harddisk (Samsung HM16HI) 1000 Mbit/s Ethernet port Phoenix BIOS

  Read the article

• Setting up Windows SBS 2008 network on Xen

  - by samyboy

  I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

  Read the article

• Reconfiguring, then deleting obsolete pagefile.sys from C: in one go using a batch script

  - by DanielSmedegaardBuus

  I'm trying to set up an automated script for a Windows XP installer. It's a batch script that runs on first boot after installation, and among the things I'm trying to accomplish, is removing the pagefile from C: entirely, and putting a 16-768 MB pagefile on D: instead. Here're my batch file instructions: echo === Creating new page file on D: ... cscript %windir%\system32\pagefileconfig.vbs /create /i 16 /m 768 /vo d: >nul echo. echo === Removing old page file from C: ... cscript %windir%\system32\pagefileconfig.vbs /delete /vo C: attrib -s -h c:\pagefile.sys del c:\pagefile.sys My problem is that while these are sane commands, the removal of the pagefile on C: requires me to reboot before those commands succeed.b Or, in other words — I have to first create the D: pagefile, then reboot and delete the c:\pagefile.sys file, or I'm stuck with a c:\pagefile.sys file which isn't even recognized by Windows itself (it'll just say that there's a page file on D:, and that C: has no pagefile at all). Obviously because already some pages are written to the C:\pagefile.sys file. So how would I go about accomplishing this in one go? Or, in two gos, if this is "batch scriptable" :) TIA, Daniel :) EDIT: I should probably clarify: Running those commands above are all valid, but they'll only succeed fully if I re-run the "attrib" and "del" commands at next boot. The C: pagefile is in use at the time, so I cannot delete the file it uses, and Windows itself won't remove it when I configure it to not use C: as a page file drive. Instead, it'll leave an orphaned c:\pagefile.sys file behind (which is really large). I don't necessarily need this to work in one go, registering the last two commands to run after a reboot would also be great :)

  Read the article

• Vista failing to load after apparently being repaired

  - by Joomaz

  Hi, I apologise if I'm a litre vague and can give more info if needed. My vista machine has been working fine until today when I tried booting it. Vista loads showing the loading bar then goes to a black screen with the cursor on which you can move. It then remains like this for several minutes, during this time the computer doesn't sound like it's doing much, it is relatively quiet. Finally the welcome screen appears. It stays on this for several minutes again and the computer reboots. This keeps happening and the machine fails to load in safe mode - the same happens. I booted the pc with the vista disk in and ran repair your computer and used the system repair. It took about 20 minutes saying it was repairing damaged giles. I booted the pc again and the same happened. I loaded the pc with yeh vista disk again and chose repair my computer again. System repair seemed to run automatically this time and agian it did the same. I rebooted and the problem persisted. I then tried system restore to a few days ago. After half a hour as it finished it said it failed due to a portion being corrupt. I am really not sure what to do now. Any advice appreciated!

  Read the article

• Can't install SB750 RAID drivers in Windows 7 for two additional storage drives

  - by jf46

  Mobo: ASUS M4A79XTD, 790X/SB750 OS: Windows 7 x64 I currently have SATA 1-4 set to RAID and SATA 5-6 set to IDE. I have an SSD connected to SATA5 with Windows 7 installed on it, and that works fine. I also have configured a RAID 1 array of two 1TB HDDs, connected to SATA 1 and 2. These don't show up in Windows, and I'm having trouble getting the RAID driver installed. I even tried booting from the Windows DVD and repairing or installing Windows, but when I navigated to the relevant .sys files on my motherboard's driver CD, Windows setup told me that the files in question weren't relevant to my hardware. To be clear: I'm not trying to install Windows on a RAID. I have Windows installed on a separate disk on a separate SATA controller. I just want to get the SB750 RAID drivers installed so that the Windows disk utility can see my RAID 1 array, which is composed of two other disks. Do I need to wipe my SSD and reinstall Windows to get the RAID driver installed? That seems kind of ridiculous, and given what I described above, I'm not even sure it would work. Any help or guidance would be appreciated - thanks! Edit: Also, I've copied the driver files from the mobo CD into system32 and rebooted, no luck. Then I changed HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV\Start from 3 to 0, and that didn't work either.

  Read the article

• Copying large files from USB devices to the internal hard drive fails on Mac OS

  - by John M. P. Knox

  I have a second-generation 13" MacBook Air running Mac OS X 10.6.6 with a 2.13 GHz processor, 4 GB of RAM, and a 256 GB SSD hard disk. I often get failures when I attempt to copy a large file or large collection of files from an external USB drive (typically a "Firewire" generation Drobo) to the internal drive. The failure behaves almost exactly as if I had pulled the USB cable from the computer in mid-transfer. I get a warning that I have removed the hard disk improperly. After this event, the drive no longer appears mounted in the finder, and I have to unplug and reinsert the USB cable to mount the drive again. I have also seen a similar problem when using Aperture 3 to import a large number of photos and videos from a USB Compact Flash card reader. The import will fail and I will have to unplug the Card Reader and import the missing items. Oddly, reversing the direction of the copy seems pretty reliable. I've never had a problem copying a large file to a USB device, meaning that I have quite a few large files which are stranded on my Drobo. Model Identifier: MacBookAir3,2 Boot ROM Version: MBA31.0061.B01 I have seen a similar issue reported on Apple's website: http://discussions.apple.com/thread.jspa?threadID=2648590&tstart=0 The only suggested resolutions there seems to be switching to another form of connectivity (e.g. firewire, which does not exist on MacBook Air), or downgrading to Mac OS 10.6.4, or reverting the USB kernel extensions to the 10.6.4 versions: http://discussions.apple.com/message.jspa?messageID=12566073#12582956 I'm not too keen on the idea of downgrading kernel extensions. Does anyone know of a hardware revision without this issue that I can trade up to? Are there any other potential solutions out there?

  Read the article

• Slow parity initialization of RAID-5 array on HP Smart Array 411 controller

  - by Rob Nicholson

  On 29th October 2011, I built a RAID-5 array using 4 x 146.8GB Seagate SAS ST3146855SS drives running at 15k connected to a PowerEdge R515 with HP Smart Array P411 controller running Windows 2008 (so nothing particularly unusual). I know that parity initialisation of a RAID-5 array can take some time but it's still running after 2.5 weeks which seems a little unusual. I'd previously built another array on the same controller using 4 x 2TB SATA-2 drives and that did take a while to complete but a) I'm sure it was less than 2.5 weeks, b) that array was ~12 times bigger and c) during initialization, the percentrage slowly increased each day. At the moment, the status display for this new 2nd array simply says "Parity Initialization Status: In Progress" and it's said that since the start. It's this lack of change on the status that worries me the most - feels like it's not actually doing anything. Do you think something has gone wrong or am I being unpatient and for some reason, the status not increasing is normal? I kind of expected a much smaller array on faster drives (15k SAS versus 7.5k SATA-2) to build in a few days. This is our primary SAN running StarWind so my "have a play" options are very limited. This 2nd array is currently in use for one small virtual disk so I could shut the target machine down, move the virtual disk to another drive and try rebuilding.

  Read the article

• Setup.exe called from a batch file crashes with error 0x0000006

  - by Alex

  We're going to be installing some new software on pretty much all of our computers and I'm trying to setup a GPO to do it. We're running a Windows Server 2008 R2 domain controller and all of our machines are Windows 7. The GPO calls the following script which sits on a network share on our file server. The script it self calls an executable that sits on another network share on another server. The executable will imediatelly crash with an error 0x0000006. The event log just says this: Windows cannot access the file for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Setup.exe because of this error. Here's the script (which is stored on \\WIN2K8R2-F-01\Remote Applications): @ECHO OFF IF DEFINED ProgramFiles(x86) ( ECHO DEBUG: 64-bit platform SET _path="C:\Program Files (x86)\Canam" ) ELSE ( ECHO DEBUG: 32-bit platform SET _path="C:\Program Files\Canam" ) IF NOT EXIST %_path% ( ECHO DEBUG: Folder does not exist PUSHD \\WIN2K8R2-PSA-01\PSA Data\Client START "" "Setup.exe" "/q" POPD ) ELSE ( ECHO DEBUG: Folder exists ) Running the script manually as administrator also results in the same error. Setting up a shortcut with the same target and parameters works perfectly. Manually calling the executable also works. Not sure if it matters, but the installer is based on dotNETInstaller. I don't know what version though. I'd appreciate any suggestions on fixing this. Thanks in advance! UPDATE I highly doubt this matters, but the network share that the script is hosted in is a shared drive, while the network share the script references for the executable is a shared folder. Also, both shares have Domain Computers listed with full access for the sharing and security tabs. And PUSHD works without wrapping the path in quotes.

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• BIOS corrupted? How to proceed? Acer Travelmate 290

  - by dtlussier

  I have a older ACER Travelmate 290 (manufactured in 2002 or 2003), which I recently tried to upgrade to Ubuntu 9.10. After doing the upgrade process it appeared as if I had a problem with my x server configuration, as on the first reboot post-install I heard the Ubuntu startup sound, but had a black screen. I thought I would then reboot again to drop down into text-mode to trouble shoot the x configuration problem. However, when I tried rebooting, something went wrong and since then when I start up the machine I get absolutely nothing except the first hardware check (i.e. HDD light flashes, CD/DVD drive spins, etc.). Other than that the screen remains totally black and I have no HDD or processor activity at all. I have tried restarting it a number of time holding down all kinds of key combinations to try and coax it into the BIOS (if possible) with no luck. I have also tried putting in both a live Linux disc and a Windows install disk without any luck. With a disk in the drive it will spin for a few seconds and then stop. All this has lead me to suspect that the BIOS is somehow corrupt (not sure about the right terminology). I have tried putting a new BIOS image and installer program downloaded from ACER on a USB key to see if it will run when I start up the machine, but no luck. I'm not sure if this method of interacting/updating/flashing the BIOS will work outside of Windows/DOS as both OSs are mentioned kind of ambiguously in the documentation. I have also taken the laptop case apart and inspected the various cards and cannot find any obviously burned out components. I'm not sure how to proceed at this point in terms of components to try, or how to try and load a new BIOS image onto the board. Any advice here would be great, especially from those with experience with this particular line of laptops. Thanks!

  Read the article

• SQL Server 2008 R2 mirroring failing

  - by andriusn

  I have two Windows 2008 R2 (Amazon EC2) instances running SQL Server 2008 R2. I use 9TB striped disks (9x1TB EBS volumes) for storage. One server is running as principal and second one as mirror. Both started from the same image, database and tlog files located on striped disk. Mirror server failed 3 times in last 2 months with errors: EventID 823 The operating system returned error 2(The system cannot find the file specified.) to SQL Server during a write at offset 0x00000048058a00 in file 'D:\TLogs***_log.ldf'. Additional messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. and EventID 1454 Database mirroring will be suspended. Server instance 'xxxxxxxxxx' encountered error 823, state 6, severity 24 when it was acting as a mirroring partner for database '***'. The database mirroring partners might try to recover automatically from the error and resume the mirroring session. For more information, view the error log for additional error messages. followed by EventID 19019 The MSSQLSERVER service terminated unexpectedly. After this rebooting instance is necessary to restore mirroring. First two times I thought it was hardware related (striped disk failure) and relaunched instance on new hardware. But the issue is back after few weeks again. It only affects mirror instances. Any help would be really appreciated. Thanks.

  Read the article

• Explorer.EXE ordinal 423 not found in urlmon.dll after updates/IE8 install

  - by Zoot

  Setting up a brand new Dell Optiplex 980 with Windows XP SP3, and everything started up fine on the first boot. My first task was to install system updates, including IE8 and WGA. After the required reboot after installing updates, I now get this error message: Explorer.EXE Ordinal not found. The ordinal 423 could not be located in the dynamic link library urlmon.dll Per my cursory Google search, this forum thread places the blame squarely on IE8. The solution provided is to enter safe mode and remove IE8. Unfortunately, when I press F8 to choose to boot safe mode, I only have the option of "Windows XP SP3 Professional" and no safe mode options. Any other ideas? Thanks in advance. FYI, I can get to the Windows Task Manager by holding down Control-Alt-Delete, but programs don't seem to run properly if you select them. I tried chatting with Dell Support, and we tried to initiate the system restore at c:\windows\system32\restore\rstrui.exe, but that had a similar "ordinal 423 not found in urlmon.dll" error.

  Read the article

• Slow performance on VMWare Linux server after Tomcat install

  - by Loftx

  We have a VMWare ESXi 4.1 server hosting a number of Linux and Windows guests. Recently a new Linux guest was added to this server and seemed to be performing well. Tomcat and some other applications on this server were then installed which seem to have caused the server to run really slowly without any obvious resource issues. Slow performance include: The time taken to bring up the password prompt over ssh takes a few seconds when it was previously instantaneous. The time taken to unzip a zip file which was previously a few seconds now takes around 30 seconds The time taken to compile vmware tools has increased by similar factors Both the VMWare console and monitoring commands don't report any issues with high CPU or memory usage but something is obviously slowing the server down somehow. Does anyone have any ideas what may be causing this issue and how it can be resolved? Thanks, Tom Edit As per your questions I’ve looked at some of the performance indicators on both the VM host and VM guest indicated. Firstly I tried reserving the full amount of memory (3gb) for this VM – no other machines on this server have any memory reservation. The swap in rate and swap out rate for the VM host and guest are now both zero. Balloon memory on the guest is zero and on the host is 3.5gb (total memory on the host is 12gb) The swap rate for the guest is also zero. Swap used by the host is 200mb on average. Compression and decompression rates for the host and guest are zero. Command aborts for the host are zero. Read latency is very low – maximum 10ms average 0.8ms. Write latency is higher – a few spikes to 170ms but mostly around 25ms – is this bad? Queue command latency is zero . Physical disk read latency averages 5ms but often 10ms Physical disk write latency averages 15ms but is often 20ms I hope this helps - let me know if you need any more information.

  Read the article

• What GPT partition type to use for protecting DRBD metadata?

  - by Carsten Scholtes

  I'm planning to install a DRBD device on a (replicated) disk with two GPT partitions. DRBD requires some space for (preferentially "internal") metadata at the end of the underlying device. I'm hesitant to leave this space unpartitionend (or unformatted in a normal partition). I'd like to reserve an extra partition at the end of the underlying disk device for the metadata. (If I understand correctly, DRBD would not care about the partition or its type and could then use that space exclusively.) My question is: Which would be a suitable GPT partition type for such a metadata partition? It should not be a type interpreted while booting (such as EF00 EFI System). It should not be a type prone to be modified accidentialy by the booted OS (such as 8200 Linux swap, 8e00 Linux LVM, fd00 Linux raid). (The booted OS will be Ubuntu Linux 12.04.3.) It should not be a type indicating a normal filesystem (such as 0c01 or 8301), prone to be formatted correspondingly. It should not be a type requiring any special content in the partition (since the content is to be handled exclusively by DRBD). It should express the purpose of being reserved for something special (namely DRBD). (The types I listed are as provided by gdisk. I'm thinking about using some type unlikely to be used by the OS (maybe bf0a Solaris Reserved 4) or an invented(?) type such as fd01 (close to fd00 Linux raid…). Would something like this be suitable, too dangerous or even possible?)

  Read the article

• A tiered approach to cloning linux partitons

  - by Djurdjura

  I'm looking at a strategy for cloning Linux (root) partitions without having to use a Live CD. Literature suggests rightly that the source and target partitions must be umounted to be able to get a clean clone. This assumes that you need to use a LiveCD. I was wondering if instead of requiring a LiveCD, if using a 3rd partition that would emulate the LiveCD functionality, if we can't achieve the same functionality. In other words, at a high level a system with 3 partitions (all bootable): Rescue Partition (LiveCD emulation) Running Partition (Source) Backup Partition (Destination) All 3 partitions are LVMS. When it's time to clone the source partition to the backup (destination) partition, we would boot to the rescue partition, unmount the other 2 partitions (is it required?), run disk check on the source, copy to the destination (dd or simple copy to avoid replicating the defragmentation from the source), run disk check on the destination partition, update Grub menu list to force boot from either partition, and reboot into that partition. My question, is it an approach that you'd recommend? MBR in all this? Any gotchas or extra checks required? Thanks, D. PS. On recommendation from members, posting here instead of stackoverflow.com.

  Read the article

• Windows Server 2003 DC hangs after network drivers update

  - by tcv

  Earlier today, we attempted to update the Broadcom BCM5716C network drivers on a Windows Server 2003. (Dell PowerEdge T310, FWIW). Since then we have not been able to boot the server in any normal mode. Safe Mode works. Safe Mode with Networking and regular bootups hang at "Applying Network Settings." I haven't tried Last Known Good Configuration nor have I tried Directory Services Restore Mode. I should also mention that the longest I've allowed "Applying Network Settings" was perhaps 30 minutes. I spoke to Dell since the server is under a basic warranty. They sent me the original Broadcom drivers. The trouble seems to be, however, that since I can only boot in Safe Mode, I can't install the application package as given. In safe mode, I receive the error: "The system administrator has set policies to prohibit this installation." I can install the drivers independently, but that doesn't allow the NICs to work. The most I've been able to get are Code 10 errors on each NIC. I plan to get back to the site tomorrow to attempt installation of a different NIC. I'm wondering what else I can try.

  Read the article

< Previous Page | 321 322 323 324 325 326 327 328 329 330 331 332  | Next Page >