Daily Archives

Articles indexed Sunday April 8 2012

Page 1/14 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How to interpret output from Linux 'top' command?

  - by Ali

  Following a discussion made HERE about how PHP-FPM consuming memory, I just found a problem in reading the memory in top command. Here is a screenshot of my top just after restarting PHP-FPM. Everything is normal: about 20 PHP-FPM processes, each consuming 5.5MB memory (0.3% of total). Here is the aged server right before restart of PHP-FPM (one day after the previous restart). Here, we still have about 25 PHP-FPM with double memory usage (10MB indicating 0.5% of total). Thus, the total memory used should be 600-700 MB. Then, why 1.6GB memory has been used?

  Read the article

• mod_rewrite "Request exceeded the limit of 10 internal redirects due to probable configuration error."

  - by Shoaibi

  What i want: Force www [works] Restrict access to .inc.php [works] Force redirection of abc.php to /abc/ Removal of extension from url Add a trailing slash if needed old .htaccess : Options +FollowSymLinks <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / ### Force www RewriteCond %{HTTP_HOST} ^example\.net$ RewriteRule ^(.*)$ http://www\.example\.net/$1 [L,R=301] ### Restrict access RewriteCond %{REQUEST_URI} ^/(.*)\.inc\.php$ [NC] RewriteRule .* - [F,L] #### Remove extension: RewriteRule ^(.*)/$ /$1.php [L,R=301] ######### Trailing slash: RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_URI} !(.*)/$ RewriteRule ^(.*)$ http://www.example.net/$1/ [R=301,L] </IfModule> New .htaccess: Options +FollowSymLinks <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / ### Force www RewriteCond %{HTTP_HOST} ^example\.net$ RewriteRule ^(.*)$ http://www\.example\.net/$1 [L,R=301] ### Restrict access RewriteCond %{REQUEST_URI} ^/(.*)\.inc\.php$ [NC] RewriteRule .* - [F,L] #### Remove extension: RewriteCond %{REQUEST_FILENAME} \.php$ RewriteCond %{REQUEST_FILENAME} -f RewriteRule (.*)\.php$ /$1/ [L,R=301] #### Map pseudo-directory to PHP file RewriteCond %{REQUEST_FILENAME}\.php -f RewriteRule (.*) /$1.php [L] ######### Trailing slash: RewriteCond %{REQUEST_FILENAME} -d RewriteCond %{REQUEST_FILENAME} !/$ RewriteRule (.*) $1/ [L,R=301] </IfModule> errorlog: Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace., referer: http://www.example.net/ Rewrite.log: http://pastebin.com/x5PKeJHB

  Read the article

• WebDAV, SVN, Apache2 on OS X 10.6.2

  - by David

  I'm trying to configure SVN server on OS X 10.6.2 via Apache2. Whenever I enable the module in Wev - Settings - Services then try accessing the site, it fails. So I attempted an apachectl configtest and I'm getting a crazy amount of errors: httpd: Syntax error on line 132 of /private/etc/apache2/httpd.conf: Cannot load /usr/libexec/apache2/mod_dav_fs.so into server: dlopen(/usr/libexec/apache2/mod_dav_fs.so, 10): Symbol not found: _dav_add_response\n Referenced from: /usr/libexec/apache2/mode_dev_fs.so\n Expected in: flat namespace\n in /usr/livexec/apache2/mod_dav_fs.so When I attempt disabling the related services and enabling then one by one (dav_fs_module, dav_module, dav_svn_module and authz_svn_mod each seems to fail. What the heck. :-( Thanks in advance, Dave

  Read the article

• SQL Server 2008 Express - "Best" backup solution?

  - by alexn

  What backup solutions would you recommend when using SQL Server 2008 Express? I'm pretty new to SQL Server, but as I'm coming from an MySQL background I thought of setting up replication on another computer and just take Xcopy backups of that server. But unfortunately replication is not available in the Express Edition. The site is heavily accessed, so there has to be no delays and downtime. I'm also thinking of doing a backup twice a day or something. What would you recommend? I have multiple computers I can use, but I don't know if that helps me since I'm using the Express version.

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

• How to stop DW20.exe running on Win 2003 Server

  - by Laurence

  Periodically my ASP.NET application crashes (usually because memory consumption exceeds maximum allowed by application pool) and DW20.exe starts up. This is a big problem because it uses huge amounts of memory and CPU for minutes at a time. I want to know how to stop DW20.exe from running. Please note, I have already tried these often mentioned solutions: Disabling error reporting in Control Panel System Advanced Error Reporting Disabling the Error Reporting Service Modifying the registry as in http://support.microsoft.com/kb/841477 (however I might have done this wrong - this doc says "add a DWReportee value of 1" - what I did was add a DWORD entry with hexadecimal value of 1 - is this right? Also only 2 of the 4 keys were present, so I only modified these, e.g. there was no HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\PCHealth key at all) So, zero points for suggesting any of the above (unless you can see I have modified the registry incorrectly)! Also zero points for suggesting I resolve whatever is causing the application crashes :) - I am figuring this out, I just want something in the mean time to stop DW20.exe eating up all the server resources. By the way, this is a Windows 2003 SP1 server, with IIS 6 and SQL 2005 installed. There is no MS Office.

  Read the article

• AWStats on Plesk consumes all of CPU and crashes server - how do you disable plesk

  - by columbo

  I have Plesk 9.0.1 running on a Red Hat server. Every week or so at about 4:10 AM the server locks up. At this time the server CPU usage shoots from 4% to 90% at the same time as a mass of awstats.pl processes start (I can't see how many as my datat only shows the top 30 processes, but all of these are awstats.pl). I turned off awstats through the Plesk control panel for all but 5 domains but I still get 90% CPU usage and at least 30 instances of awstats.pl happening at 4:10am as usual. Does anyone know why this may be? Does anyone know how to disable awstats (I have stats covered using piwik)? Or how do I uninstall awstats without snarling up Plesk?

  Read the article

• Dovecot install: what does this error mean?

  - by jamie

  I have postfix and dovecot installed on CentOS 6 (linode) along with MySQL. The table and user is already set up, postfix installed fine, but dovecot gives me this error in the mail log: Warning: Killed with signal 15 (by pid=9415 uid=0 code=kill) The next few lines say this: Apr 7 16:13:35 dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Apr 7 16:13:35 dovecot: config: Warning: NOTE: You can get a new clean config file with: doveconf -n > dovecot-new.conf Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:1: protocols=pop3s is no longer supported. to disable non-ssl pop3, use service pop3-login { inet_listener pop3 { p$ Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:5: ssl_cert_file has been replaced by ssl_cert = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:6: ssl_key_file has been replaced by ssl_key = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:8: namespace private {} has been replaced by namespace { type=private } Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:24: add auth_ prefix to all settings inside auth {} and remove the auth {} section completely Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:25: auth_user has been replaced by service auth { user } I am following directions for the install on CentOS 5 with changes in the dovecot.conf file from different sources specific to CentOS 6. So the dovecot.conf file might not be correct, but there is no good source I have found yet for making dovecot install correctly. Can anyone tell me what the error above means? The terminal does not give any message as to start OK or FAIL. When I issue the service dovecot start command, it says: Starting Dovecot Imap: and nothing more.

  Read the article

• Varnish Running VCC-compiler failed on purge

  - by FLX

  I've been following this guide which uses this default.vcl. However, when starting Varnish I get the following error: * Starting HTTP accelerator [fail] storage_malloc: max size 1024 MB. Message from VCC-compiler: Expected '(' got ';' (program line 341), at (input Line 43 Pos 22) purge; ---------------------# Running VCC-compiler failed, exit 1 VCL compilation failed Which means that there is something wrong with purge here: sub vcl_hit { if (req.request == "PURGE") { purge; error 200 "Purged."; } } I don't see anything wrong, can someone explain? Thanks!

  Read the article

• DNS entries issues

  - by Yaman

  I have some troubles with my DNS entries (or maybe my Apache conf). I have something like this : kira.mydomain.com A 123.45.67.89 youfood.mydomain.com CNAME kira.mydomain.com www.youfood.mydomain.com CNAME youfood.mydomain.com All's good when I check theses entries with nslookup. When I try going on http://www.youfood.mydomain.com, it work but not with http://youfood.mydomain.com ... Here my vhost : <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName youfood.mydomain.com ServerAlias www.youfood.mydomain.com DocumentRoot /home/ftp_youfood/www/trunk <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /home/ftp_youfood/www> Options FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> [...] </VirtualHost> Is there anything wrong ?

  Read the article

• Dynamic DNS registration for VPN clients

  - by Eric Falsken

  I've got a VPN server set up in my Active Directory on a remote network. (VPN Server is separate box from DNS/AD) When I dial into the network (client machine is not a member of the AD) the machine does not register its IP or Hostname in the DNS. I've played with all possible combinations of DHCP and RRAS-allocated IP pools, and none of them seem to cause my client to register. Is it because my client has to be a member of the domain? Are there some security settins I can tweak so that it can register its hostname/ip? I've looked in the event logs (System and Security) for the AD, DNS, DHCP, RRAS, and the client machine, and don't see anything relating to DNS Registration. Here's the IPConfig on the client machine (once connected): PPP adapter My VPN Name: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : My VPN Name Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.22(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.52 <- DC1 192.168.1.53 <- DC2 NetBIOS over Tcpip. . . . . . . . : Enabled Edit: It looks like my clients are not recieving the DHCP Scoope Options. I found this great article in Microsoft's KB. So the problem here is that the VPN Server "pre-reserves" the DHCP addresses, but then you have to add the DHCP Relay Agent to relay the secondary request for scope options. My problem is that the DHCP Relay Agent isn't relaying to the local DHCP server (same box as the VPN/RRAS). I've configured the DHCP Relay Agent according to this KB, but it dosn't work for a local DHCP server. (I see the request count increasing, but no responses) I was able to get everything working by specifying the DNS server and domain name in the VPN connection properties on the client. But am still unable to assign it (or the default gateway) dynamically via DHCP. The client also has to be a member of the remote domain.

  Read the article

• When Installing Oracle Client 11.1.0.7 can I use a common directory for Oracle Base?

  - by Anders

  I am trying to install Oracle Client 11.1.0.7 on a Windows Server 2008 64-bit. To some this might not be rocket science but I can't understand what the options under the install screen "Specify Home Details" mean. The defaults given suggest that I use Oracle Base and install software under my own account name. It also suggests that each user should have a separate Oracle Base. This seems counter intuitive to me. I am doing a server install after all. All I want to use the installation for is to connect to an Oracle Database from Reporting Services. Can I safely ignore this and just accept the defaults? What are the implications if I change the location to a common directory?

  Read the article

• cPAddons version conflict with Wordpress

  - by Joel Alejandro

  I have multiple users on my CentOS 5.7 server with WHM/cPanel, who have installed WordPress 3.2.1, and eventually did a manual update to 3.3.1, from Wordpress itself. Now the version of WP for those users doesn't match th one detected by cPanel, and of course, "Upgrade" doesn't work because the directory can't be cleaned (WP is already working there). I've looked on the .cpaddons folder of each user account, and there's a YAML file there, but I'm not sure how can I touch that file for solving this issue. Is there any way to tell cPanel that those WP installations are in fact, 3.3.1?

  Read the article

• API Management Solutions

  - by Mike

  I'm currently building an API and am looking for a tool to allow me to monitor (in a GUI) and rate limit usage. I've come across a few enterprise solutions including: http://apigee.com/ http://mashery.com/ http://www.layer7tech.com/ http://www.3scale.net/ The Apigee enterprise plan is exactly what I'm looking for but plans start at $3000 / month which is out of my price range. The other solutions are all either to expense or do not provide the solution I'm looking for. This led me to look at some open source options including: http://apiaxle.com/ https://code.google.com/p/varnish-apikey/wiki/UsageManual Varnish seems like a fairly complete solution, however I would need to build a GUI to visualise the data. My final option would to build a solution from scratch using EventMachine and ruby. Any advice?

  Read the article

• What ssh command would I use to set up "backwards listening"

  - by Nathan

  Machine A is behind a firewall. I have physical access to it, but I want to log into it remotely, and I do not have access to the firewall settings. Machine B is remote, and not behind any firewall. (It's my linode) Machine C is the mobile device I'm going to attempt to ssh into A from. Is there an ssh command that I can run from machine A that connects to machine B and stays open, that will allow me to log into A from C, via B? From the manual I'd guess it would be to run the follwing on A ssh -R *:9999:localhost:22 me@B and then run this on C ssh me@B -p 9999 but the previous command reports "Connection refused."

  Read the article

• CPU Usage at 100% with "Hardware Interrupts"

  - by eventualEntropy

  After turning on my desktop one day, I found that my CPU usage was maxed out at 100%, with 99% of that going to hardware "Interrupts". I tried to enable/disable all my devices one by one through the device manager, and found that I could get the CPU usage used by the Interrupts down to 50% by disabling all devices labelled "USB Host Controller" (except the ones for the mouse/keyboard). I found that I also got 10-20% more from disabling "High Definition Audio Controller". Following the tutorial at: http://www.msfn.org/board/topic/140263-how-to-get-the-cause-of-high-cpu-usage-by-dpc-interrupt/ Led me to similar conclusions (that is, that the culprit is mostly "USB Host Controller"): I've tried updating my asus motherboard driver and my video card driver. This is on Windows 7 64 bit. I've spent hours trying to figure this out and I'm running out of ideas short of formatting (which might still not fix it!).

  Read the article

• Kernel-Power errors acer aspire m7720

  - by toby

  hey to whom it concerns i have an acre aspire m7720 with 12gb ram and 5 tb hardives everything else is the same and i get Kernel-Power errors and my monitor say input not supported and i have to turn the power off cause i cant see anything on my screen wondering what the hell is going on and how do i fix this cause it pisses me off and wondering if i need a bigger power supply is the problem toby

  Read the article

• Running hardware with only 32bit drivers in 64bit windows

  - by Howard

  Recently we had to upgrade a system to handle added HD IP cameras. This upgrade involved an entirely new computer build with the exception of a rather pricey Geovision DVR (PCI/GV1480 series). Apparently while these cards do support Windows 7, they do not support Windows 7 x64. I'm stuck between a rock and a hard place here trying to figure out how we can remedy this, is there a virtualization solution that will allow devices with driver issues to passthru to the Guest OS? I was thinking XPMode may work for this solution however I am unsure if it runs 32bit or 64bit and if it'll allow driver-issue devices to pass to it. Any help would be greatly appreciated, Best Regards, Howard

  Read the article

• Macbook Pro won't boot from DVD with SSD

  - by Adam Carr

  Here's the timeline of events. Had a running MBP 17 Early 2011 Thunderbolt with OWC Mercury Extreme Pro SSD 115GB drive. Installed Windows 7 via bootcamp. I have done this multiple times before and every time I need to format the bootcamp partition before installing. I think this time I actually deleted the partition and then selected the freespace to install. This worked fine for the most part but I wasn't able to boot the boot camp partition using vmware fusion. I gave up and used the boot camp assistant to revert back to one mac partition. I was getting some odd behavior so I rebooted the machine. It then came up with a message saying no bootable partiton. This made me think (and still does) that the windows install using the free space versus the boot camp partition caused the windows MBR boot loader to get installed incorrectly and mucked up the OS X installation. Ok, fine, I can just reinstall. I can't seem to boot from the original MBP installation DVD. I hold down c on boot but I never get past the all grey screen. I hear the DVD drive spin up but it eventually stops. I put the original HD back in it and everything works fine but when I put the SSD in, I can't boot from the DVD drive. I have already set up an RMA with OWC to send back the drive but considering the order of events, I feel as though it isn't a hardware issue but can't seem to figure out how to fix it. I can always send it back in but figured I would check and see if anyone could offer some guideance/assistence before doing so.

  Read the article

• HDD cannot be booted from

  - by K.Wong

  I have an ASUS A52F, no mods, with Win7 preinstalled. There is one hard drive, two partitions, one for the OS (C:) and one for data (D:) After laptop trauma, i.e. I dropped it, it still worked fine. However, when chkdisk was run on the C: drive chkdisk crashed, and Windows is unbootable. Windows Startup Manager utility was run, but error code 0xc00000e9 was given. Windows help db shows that this is a BIOS problem, however in BIOS setup the drive can be accessed, and folders can be shown. I also burned a Ubuntu 12.04 distro, and booted off it, but my internal HDD is missing and cannot be accessed. When installation program is run the HDD shows up as a location to install to yet the drive is shown as blank. tl;dr: HDD damaged, chkdisk crashed. Windows 7 is unbootable. Given error code, according to Microsoft db, is a BIOS problem, yet in BIOS the drive is accessible. different OS (Ubuntu 12.04), booted off a distro, yet HDD is inaccessible. Quick help appreciated.

  Read the article

• setup L2TP on Ubuntu 10.10

  - by luca

  I'm following this guide to setup a VPS on my Ubuntu VPS: http://riobard.com/blog/2010-04-30-l2tp-over-ipsec-ubuntu/ My config files are setup as in that guide, openswan version is 2.6.26 I think.. It doesn't work, I can show you my auth.log (on the VPS): Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [RFC 3947] method set to=109 Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Feb 18 06:11:07 maverick pluto[6909]: packet from 93.36.127.12:500: received Vendor ID payload [Dead Peer Detection] Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: responding to Main Mode from unknown peer 93.36.127.12 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: STATE_MAIN_R1: sent MR1, expecting MI2 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: STATE_MAIN_R2: sent MR2, expecting MI3 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: Main mode peer ID is ID_IPV4_ADDR: '10.0.1.8' Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[7] 93.36.127.12 #7: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: deleting connection "L2TP-PSK-NAT" instance with peer 93.36.127.12 {isakmp=#0/ipsec=#0} Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: new NAT mapping for #7, was 93.36.127.12:500, now 93.36.127.12:36810 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Feb 18 06:11:07 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: received and ignored informational message Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: the peer proposed: 69.147.233.173/32:17/1701 -> 10.0.1.8/32:17/0 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: responding to Quick Mode proposal {msgid:183463cf} Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: us: 69.147.233.173<69.147.233.173>[+S=C]:17/1701 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: them: 93.36.127.12[10.0.1.8,+S=C]:17/64111===10.0.1.8/32 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Feb 18 06:11:08 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #8: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x0b1cf725 <0x0b719671 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=93.36.127.12:36810 DPD=none} Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: received Delete SA(0x0b1cf725) payload: deleting IPSEC State #8 Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: netlink recvfrom() of response to our XFRM_MSG_DELPOLICY message for policy eroute_connection delete was too long: 100 > 36 Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: netlink recvfrom() of response to our XFRM_MSG_DELPOLICY message for policy [email protected] was too long: 168 > 36 Feb 18 06:11:28 maverick pluto[6909]: | raw_eroute result=0 Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: received and ignored informational message Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12 #7: received Delete SA payload: deleting ISAKMP State #7 Feb 18 06:11:28 maverick pluto[6909]: "L2TP-PSK-NAT"[8] 93.36.127.12: deleting connection "L2TP-PSK-NAT" instance with peer 93.36.127.12 {isakmp=#0/ipsec=#0} Feb 18 06:11:28 maverick pluto[6909]: packet from 93.36.127.12:36810: received and ignored informational message and my system log on OSX (from where I'm connecting): Feb 18 13:11:09 luca-ciorias-MacBook-Pro pppd[68656]: pppd 2.4.2 (Apple version 412.3) started by luca, uid 501 Feb 18 13:11:09 luca-ciorias-MacBook-Pro pppd[68656]: L2TP connecting to server '69.147.233.173' (69.147.233.173)... Feb 18 13:11:09 luca-ciorias-MacBook-Pro pppd[68656]: IPSec connection started Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: Connecting. Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Information message). Feb 18 13:11:09 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA). Feb 18 13:11:10 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Feb 18 13:11:10 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Feb 18 13:11:10 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Feb 18 13:11:10 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Feb 18 13:11:10 luca-ciorias-MacBook-Pro racoon[68453]: Connected. Feb 18 13:11:10 luca-ciorias-MacBook-Pro pppd[68656]: IPSec connection established Feb 18 13:11:30 luca-ciorias-MacBook-Pro pppd[68656]: L2TP cannot connect to the server Feb 18 13:11:30 luca-ciorias-MacBook-Pro configd[20]: SCNCController: Disconnecting. (Connection tried to negotiate for, 22 seconds). Feb 18 13:11:30 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Information message). Feb 18 13:11:30 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Feb 18 13:11:30 luca-ciorias-MacBook-Pro racoon[68453]: IKE Packet: transmit success. (Information message). Feb 18 13:11:30 luca-ciorias-MacBook-Pro racoon[68453]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Feb 18 13:11:31 luca-ciorias-MacBook-Pro racoon[68453]: Disconnecting. (Connection was up for, 20.157953 seconds).

  Read the article

• How do I prevent or override a group policy on Windows 7?

  - by Kevin

  A few months ago my company was purchased by a large corporation. We recently switched our network over to the large corporate network which has more restrictions requirements. One of these is the requirement to use a proxy server for Internet traffic. However, some of our internal servers are not recognized by the corporate DNS, so we need to provide the fully qualified domain name. For W7, we make changes to the Internet Properties for IE8 and Chrome to include our domain name as an exception to the proxy server (e.g., *.foobar.com). The problem is that a group policy that does not include our domain name is continually pushed out to my systems throughout the day. This requires me to make the appropriate changes to the Internet Properties several times a day in order to access our internal servers. Is there a way that I can prevent the group policy from being pushed to my systems or detect when the group policy is pushed and override it? I am an administrator on all of my systems. I do have Firefox installed which is not subject to the same group policy push, but I need to have IE8 and Chrome working.

  Read the article

• Can RPM packages be installed into Cygwin?

  - by Dejian Zhao

  I noticed that there is a command - rpm - under Cygwin 1.7. Does that mean RPM packages can be installed into Cygwin? I tried to install ncbi-blast-2.2.26+-3.i686.rpm (see: ftp://ftp.ncbi.nlm.nih.gov/blast/executables/blast+/LATEST/ ) into Cygwin 1.7.13 with the command "install -i ncbi-blast-2.2.26+-3.i686.rpm". However, error message appeared as below. I tried to search for the missing libs using the setup.exe of Cygwin. It seems that some of them were not present, such as libc.so.6, libdl.so.2, libm.so.6, libnsl.so.1, and libz.so.1. Where can I get these libs? Thanks! $ rpm -i ncbi-blast-2.2.26+-3.i686.rpm error: Failed dependencies: /usr/bin/perl is needed by ncbi-blast-2.2.26+-3 libbz2.so.1 is needed by ncbi-blast-2.2.26+-3 libc.so.6 is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.0) is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.1) is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.1.2) is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.1.3) is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.2) is needed by ncbi-blast-2.2.26+-3 libc.so.6(GLIBC_2.3) is needed by ncbi-blast-2.2.26+-3 libdl.so.2 is needed by ncbi-blast-2.2.26+-3 libdl.so.2(GLIBC_2.0) is needed by ncbi-blast-2.2.26+-3 libdl.so.2(GLIBC_2.1) is needed by ncbi-blast-2.2.26+-3 libgcc_s.so.1 is needed by ncbi-blast-2.2.26+-3 libgcc_s.so.1(GCC_3.0) is needed by ncbi-blast-2.2.26+-3 libgcc_s.so.1(GLIBC_2.0) is needed by ncbi-blast-2.2.26+-3 libm.so.6 is needed by ncbi-blast-2.2.26+-3 libnsl.so.1 is needed by ncbi-blast-2.2.26+-3 libpthread.so.0 is needed by ncbi-blast-2.2.26+-3 libpthread.so.0(GLIBC_2.0) is needed by ncbi-blast-2.2.26+-3 libpthread.so.0(GLIBC_2.1) is needed by ncbi-blast-2.2.26+-3 libpthread.so.0(GLIBC_2.2) is needed by ncbi-blast-2.2.26+-3 libpthread.so.0(GLIBC_2.3.2) is needed by ncbi-blast-2.2.26+-3 librt.so.1 is needed by ncbi-blast-2.2.26+-3 libstdc++.so.6 is needed by ncbi-blast-2.2.26+-3 libstdc++.so.6(CXXABI_1.3) is needed by ncbi-blast-2.2.26+-3 libstdc++.so.6(GLIBCXX_3.4) is needed by ncbi-blast-2.2.26+-3 libstdc++.so.6(GLIBCXX_3.4.5) is needed by ncbi-blast-2.2.26+-3 libz.so.1 is needed by ncbi-blast-2.2.26+-3 perl(Archive::Tar) is needed by ncbi-blast-2.2.26+-3 perl(Digest::MD5) is needed by ncbi-blast-2.2.26+-3 perl(File::Temp) is needed by ncbi-blast-2.2.26+-3 perl(File::stat) is needed by ncbi-blast-2.2.26+-3 perl(Getopt::Long) is needed by ncbi-blast-2.2.26+-3 perl(Net::FTP) is needed by ncbi-blast-2.2.26+-3 perl(Pod::Usage) is needed by ncbi-blast-2.2.26+-3 perl(constant) is needed by ncbi-blast-2.2.26+-3 perl(strict) is needed by ncbi-blast-2.2.26+-3 perl(warnings) is needed by ncbi-blast-2.2.26+-3

  Read the article

• Can I prevent tv-out from disconnecting when monitor sleeps?

  - by Damon

  I have my TV connected to my computer (windows 7) through an HDMI cable that also carries the sound. I like to put on music on my TV, but the problem is when my monitor goes to sleep back in my office, it switches off the hdmi connection completely and the audio goes back to my PC. I would like a way to stop this from happening without turning off sleep mode entirely. I have an ATi Radeon 5700

  Read the article

• Unable to open attachment in Windows Live Mail 2011 (Build 15.4.3502.0922)

  - by Anon2010

  I use Windows Live Mail 2011 (Build 15.4.3502.0922), in Windows 7 Pro 64. When I receive an email message that has an attachment, when I double click to open this attachment, nothing happens. Any kind of attachment, nothing happens. If I right click and choose "Open", nothing happens either. If I right click and choose Save As, I can save the file to disk and open it via Windows Explorer. I would like to be able to double click to open the attachment. I tried to repair WLM but that didn't make any difference. My antivirus is Microsoft Security Essentials. Does anyone know anything about this issue? Thanks

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >