Posted
by Pol
on Server Fault
See other posts from Server Fault
or by Pol
Published on 2010-01-15T08:57:24Z
Indexed on
2010/03/17
18:51 UTC
Read the original article
Hit count: 524
Hello forum,
I looking for a way to get the list of the top bandwidth eater on my Juniper ssg5. On my old OpenBSD Box I had a command line version of ntop. It was just perfect.
How can I do the same thing whith the SSG?
Thank you !
© Server Fault or respective owner
as seen on Server Fault
- Search for 'Server Fault'
We have a SharePoint (MOSS 2007 on Win2003 R2) with SSRS reports (from SQL 2005) embedded in it.
When we connect to the SharePoint portal through our VPN (firewall is Juniper SA4000) and using Internet Explorer (6, 7, and 8) and try to export any SSRS report under Excel, we get an error message:
Internet…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
I've followed the instructions to configure a VPN between a netscreen device and a Cisco PIX as directed by Cisco's [netscreen to PIX VPN]http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801c4445.shtml article.
The only differences are that I'm running PIX 6.3(5)…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
Hi,
I want to know how the request & response from the VPN server on
e.g.:
https://host.tld/dana/jw?con=1234567890&seqno=7
is encoded, the output seems to be binary. I assume it is the application data which gets exchanged with this request, am I right in this?
If not, what else gets transferred…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
I tested my dns servers with the oarc test and my size limit is at least 1403 bytes. I performed the same test before my Juniper ISG 2000 and the result is 2047 bytes.
According to the chapter IP "Fragments Filtered" and this article, I think I have a fragmentation problem.
This article talks about…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
Hello forum,
I looking for a way to get the list of the top bandwidth eater on my Juniper ssg5. On my old OpenBSD Box I had a command line version of ntop. It was just perfect.
How can I do the same thing whith the SSG?
Thank you !
>>> More
as seen on Server Fault
- Search for 'Server Fault'
As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one.
We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
Hello forum,
I looking for a way to get the list of the top bandwidth eater on my Juniper ssg5. On my old OpenBSD Box I had a command line version of ntop. It was just perfect.
How can I do the same thing whith the SSG?
Thank you !
>>> More
as seen on Server Fault
- Search for 'Server Fault'
I have been assigned to establish a Internet IPsecVPN connection between two sites using Cisco ASA5505
A site currently has following setup.(Same setup is expected in another site)
Internet-----ADSL Router-----Juniper SSG5-----Intranet
(Im not sure what is configured on SSG5 and if router is in bridge…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5.
The tunnel is up and running, but I cannot get any data through it.
The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when…
>>> More
as seen on Server Fault
- Search for 'Server Fault'
I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway.
Now I need to configure…
>>> More
