Daily Archives

Articles indexed Friday October 19 2012

Page 1/15 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Why is this LTO4 Tape-drive not working

    - by Tim Haegele
    # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

    Read the article

  • DHCP forwarding behind access list on a Cisco Catalyst

    - by Ásgeir Bjarnason
    I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

    Read the article

  • How can I download Maven artifacts in chef?

    - by recampbell
    I want to do something like this in a chef recipe: maven_artifact "/opt/foo/my.jar" do source "com.foo:my:0.1:jar" end But I can't find a cookbook which provides this. I've written something which basically does this but it doesn't handle snapshots, which requires parsing maven-metadata.xml. Before I plunge into this, I wanted to be sure I wasn't missing something obvious since this seems like a basic usecase.

    Read the article

  • Internal SFTP Settings

    - by matt ryan
    Goal: to limit user access to home directory and symlinked directories in home. I tried the following configuration in sshd_config # Subsystem sftp /usr/lib/openssh/sftp-server Subsystem sftp internal-sftp Match user matt ChrootDirectory %h X11Forwarding no AllowTcpForwarding no ForceCommand internal-sftp and then restarted sshd. User can't login using the correct password. Connection refused authentication failed.

    Read the article

  • How to get average of multiple time series

    - by Supun Kamburugamuva
    I have few computers running. I want to get the average CPU usage of these computers and plot it as a graph. So I've collected CPU usage in regular intervals in these machines. So for each computer I have a data set of time and CPU usage. But the times at which CPU measurements are taken in different machines are not in sync. For example in 1st machine CPU may be measured in time 1, 5, 9. In the second machine CPU may be measured in time 2, 5, 8. I want to get an average data series from these different data sets. Could you point me to some resources? Thanks - Supun.

    Read the article

  • Upgrading my home network to Gigabit Ethernet and Wireless-N turns out slower than before

    - by Raheel Khan
    My home network has three desktops, three laptops and some NAS drives. All desktops and NAS drives support Gigabit LAN and all laptops support Wireless-N. I was running a 100 BaseT switch though. I recently purchased a Gigabit Ethernet Switch and an Wireless-N ADSL Modem-Router. After upgrading, I noticed that the wireless file transfer speeds from laptop-to-NAS and vice versa became terribly slow. Possibly even slower than before the upgrade. The transfer speeds from desktop-to-NAS (wired) have improved though. As an example, copying a 50GB file from laptop-to-NAS was estimated at 15 hours! Is there something I can do to improve this? Also, should I consider buying a dedicated wireless access point for speed rather than using the Wireless modem-router?

    Read the article

  • Drivers for Wacom Bamboo Tablet on Windows 7

    - by hcl
    I would like to use my Bamboo tablet on my newly installed windows 7 box. However I definitively only want have the drivers to be installed. I don’t want all the additional software which is provided by Wacom in the standard software Installation package. I already tried different installation packages from the Wacom webpage, but I have not found a package which does not install all the additional apps (Adobe AIR etc). I also have not found an option to disable the installation of the undesired apps in the installer . Have I missed something? May someone give me a hint on how to get/install the drivers only?

    Read the article

  • Ubuntu not connecting to network in Hyper-V

    - by soandos
    I am unable to connect the Ubuntu guest (both 12.10 and 12.04) to the internet via hyper-V. Here is what I have done so far (with much thanks due to @Kronos's blog post on the topic): Created a switch in the switch manager with connection set to external, selected my wifi card (Intel Centrino Ultimate-N 6300 AGN). If it matters, the Microsoft Filtering Platform is checked under extensions. Added this switch to my Ubuntu guest. I also tried a different wireless card (Aethros 9285) same issue. Connecting through my wired card works just fine (assume that I select that card, and I am wired in of course). Making it a legacy network adapter does not fix the issue. Ubuntu can see this connection, but is unable to connect to it. What follows is what I attempted to do to get Ubuntu to connect: Start and restart the network manager Restart the machine Verify that it could in fact see the adapter (resulted in device not ready a few times) How can I get this to work properly?

    Read the article

  • OS X 10.6 won't automatically connect to wireless even though remember network is checked

    - by Hendy
    Upgraded to 10.6 recently. 10.5 would connect to my home network whenever I was home. 10.6 constantly pops up the network selection dialog and asks me what network I want to join. I click my home network and the password is already entered (so it "remembers" the network). "Remember network" is checked... but it does it every time. How do I get 10.6 to connect to networks automatically whenever it sees them?

    Read the article

  • Port binding conflicts with "switch user" on Windows 7

    - by C-dizzle
    We are using the switch user function within Windows 7 under an active directory network. We have one application in particular that gives us an error: Only one usage of each socket address (protocol/network address/port) is normally permitted. bind Port 10001 Are there any other ports that can only be used at one time that might have an adverse effect on the other user? We try to mentor our users to use the log off function instead of switch user, but that doesn't always happen. As an alternative, is it possible to disable the 'switch user' button on our machines?

    Read the article

  • How to keep Ubuntu 11.10 and Kate editor w/terminal from changing command line when changing tabs?

    - by Kairan
    I am programming C using Kate editor in Ubuntu 11.10. It works great, but when I change tabs in Kate, the terminal line changes to the file path of the tab I click on. Normally this is not a big deal (other than annoyingly adding extra text to my terminal) however if I am currently RUNNNING a C program, it obviously will type at the command line, which is not so cool. Example terminal window for my C program (its at a menu): 1) select opt 1 2) select opt 2 Enter choice: (here it waits for prompt from user) Now when I click a tab in Kate, it wants to put in the cd / path of the file in that tab, such as: cd /home/user/os/files And of course since my terminal was waiting for prompt from user it gets that command.. not good. Perhaps there is no fix, but maybe someone knows? Obviously I could choose NOT to switch tabs or end program before switching tabs... Note: I probably made the mistake of putting this under StackOverflow which is more of a programming area - so though repost here might be best (I am not sure how to link the questions but will paste hyperlink to that post - I dont want to violate any stackoverflow/superuser violations) Suggestions on merging them are welcome or if I should delete one? StackOverFlow Question

    Read the article

  • Windows 8 not accepting password for a while

    - by soandos
    I recently upgraded from windows 8 Consumer Preview to Windows 8 Pro (RTM through dreamspark premium), and have the following issue: When I attempt to log in after a restart, it often takes a while (~3 minutes) for the computer to accept the password (Each try goes relatively quickly, a few seconds at most before telling me I have an incorrect password). I changed the password, and this issue is unresolved (the old password came with the upgrade). What could be doing this?

    Read the article

  • Release Notes for 10/18/2012

    Below are the release notes from this week's deployment. Improvements and Bug Fixes Updated the Source browsing to fixed width and full browser height. The source browsing experience now defaults to the fixed width layout. But, if you really want to take advantage of that 30" monitor you have on your desk, you can expand the source to fill the browser window. Just click on the little plus icon in the upper right. Let us know what you think.  Thank you A big thank you to CodePlex users Coilz and CursedPerVerse for reporting an issue with deploying to AppHarbor, that issue has been resolved.  Feedback Have ideas on how to improve CodePlex? Please visit our suggestions page! Vote for existing ideas or submit a new one. As always you can reach out to the CodePlex team on Twitter @codeplex or reach me directly @mgroves84

    Read the article

  • SQLAuthority News – Storing Data and Files in Cloud – Dropbox – Personal Technology Tip

    - by pinaldave
    I thought long and hard about doing a Personal Technology Tips series for this blog.  I have so many tips I’d like to share.  I am on my computer almost all day, every day, so I have a treasure trove of interesting tidbits I like to share if given the chance.  The only thing holding me back – which tip to share first?  The first tip obviously has the weight of seeming like the most important.  But this would mean choosing amongst my favorite tricks and shortcuts.  This is a hard task. Source: Dropbox.com My Dropbox I have finally decided, though, and have determined that the first Personal Technology Tip may not be the most secret or even trickier to master – in fact, it is probably the easiest.  My today’s Personal Technology Tip is Dropbox. I hope that all of you are nodding along in recognition right now.  If you do not use Dropbox, or have not even heard of it before, get on the internet and find their site.  You won’t be disappointed.  A quick recap for those in the dark: Dropbox is an online storage site with a lot of additional syncing and cloud-computing capabilities.  Now that we’ve covered the basics, let’s explore some of my favorite options in Dropbox. Collaborate with All The first thing I love about Dropbox is the ability it gives you to collaborate with others.  You can share files easily with other Dropbox users, and they can alter them, share them with you, all while keeping track of different versions in on easy place.  I’d like to see anyone try to accomplish that key idea – “easily” – using e-mail versions and multiple computers.  It’s even difficult to accomplish using a shared network. Afraid that this kind of ease looks too good to be true?  Afraid that maybe there isn’t enough storage space, or the user interface is confusing?  Think again.  There is plenty of space – you can get 2 GB with just a free account, and upgrades are inexpensive and go up to 100 GB of storage.  And the user interface is so easy that anyone can learn to use it. What I use Dropbox for I love Dropbox because I give a lot of presentations and often they are far from home.  I can keep my presentations on Dropbox and have easy access to them anywhere, without needing to have my whole computer with me.  This is just one small way that you can use Dropbox. You can sync your entire hard drive, or hard drives if you have multiple computers (home, work, office, shared), and you can set Dropbox to automatically sync files on a certain timeline, or whenever Dropbox notices that they’ve been changed. Why I love Dropbox Dropbox has plenty of storage, but 2 GB still has a hard time competing with the average desktop’s storage space.  So what if you want to sync most of your files, but only the ones you use the most and share between work and home, and not all your files (especially large files like pictures and videos)?  You can use selective sync to choose which files to sync. Above all, my favorite feature is LanSync.  Dropbox will search your Local Area Network (LAN) for new files and sync them to Dropbox, as well as downloading the new version to all the shared files across the network.  That means that if move around on different computers at work or at home, you will have the same version of the file every time.  Or, other users on the LAN will have access to the new version, which makes collaboration extremely easy. Ref: rzfeeser.com Dropbox has so many other features that I feel like I could create a Personal Technology Tips series devoted entirely to Dropbox.  I’m going to create a bullet list here to make things shorter, but I strongly encourage you to look further into these into options if it sounds like something you would use. Theft Recover Home Security File Hosting and Sharing Portable Dropbox Sync your iCal calendar Password Storage What is your favorite tool and why? I could go on and on, but I will end here.  In summary – I strongly encourage everyone to investigate Dropbox to see if it’s something they would find useful.  If you use Dropbox and know of a great feature I failed to mention, please share it with me, I’d love to hear how everyone uses this program. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority News, T SQL, Technology Tagged: Personal Technology

    Read the article

  • My Oracle Suport?????

    - by Dongwei Wang
    ????????????????,??????MOS???????(????),????????????????????????????:Note 62143.1 - Troubleshooting: Tuning the Shared Pool and Tuning Library Cache Latch ContentionNote 376442.1 - * How To Collect 10046 Trace (SQL_TRACE) Diagnostics for Performance IssuesNote 749227.1 - * How to Gather Optimizer Statistics on 11gNote 1359094.1 - FAQ: How to Use AWR reports to Diagnose Database Performance IssuesNote 1320966.1 - Things to Consider Before Upgrading to 11.2.0.2 to Avoid Poor Performance or Wrong ResultsNote 1392633.1 - Things to Consider Before Upgrading to 11.2.0.3 to Avoid Poor Performance or Wrong Results????????????????”??“???,?????????????????(PDF??)???????????????”Rate this document“????

    Read the article

  • Install Oracle Configuration Manager's Standalone Collector

    - by Get Proactive Customer Adoption Team
    Untitled Document The Why and the How If you have heard of Oracle Configuration Manager (OCM), but haven’t installed it, I’m guessing this is for one of two reasons. Either you don’t know how it helps you or you don’t know how to install it. I’ll address both of those reasons today. First, let’s take a quick look at how My Oracle Support and the Oracle Configuration Manager work together to gain a good understanding of what their differences and roles are before we tackle the install.   Oracle Configuration Manger is the tool that actually performs the data collection task. You deploy this lightweight piece of software into your system to collect configuration information about the system and OCM uploads that data to Oracle’s customer configuration repository. Oracle Support Engineers then have the configuration data available when you file a service request. You can also view the data through My Oracle Support. The real value is that the data Oracle Configuration Manager collects can help you avoid problems and get your Service Requests solved more quickly. When you view the information in My Oracle Support’s user interface to OCM, it may help you avoid situations that create problems. The proactive tools included in Oracle Configuration Manager help you avoid issues before they occur. You also save time because you didn’t need to open a service request. For example, you can use this capability when you need to compare your system configuration at two points in time, or monitor the system health. If you make the configuration data available to Oracle Support Engineers, when you need to open a Service Request the data helps them diagnose and resolve your critical system issues more quickly, which means you get answers more quickly too. Quick Installation Process Overview Before we dive into the step-by-step details, let me provide a quick overview. For some of you, this will be all you need. Log in to My Oracle Support and download the data collector from Collector tab. If you don’t see the Collector tab, click the More tab gain access. On the Collector tab, you will find a drop-down list showing which platforms are available. You can also see more ways to the Collector can help you if you click through the carousel of benefits. After you download the software for your platform, use FTP to move that file (.zip) from your PC to the server that hosts the Oracle software. Once you have that file on the server, locate the $ORACLE_HOME directory, and unzip the file within that directory. You can then use the command line tool to start the installation process. The installation process requires the My Oracle Support credential (Support Identifier, username, and password) Proxy specification (Host IP Address, Port number, username and password) Installation Step-by-Step Download the collector zip file from My Oracle Support and place it into your $Oracle_Home Unzip the zip file you downloaded from My Oracle Support – this will create a directory named CCR with several subdirectories Using the command line go to “$ORACLE_HOME/CCR/bin” and run the following command “setupCCR” Provide your My Oracle Support credential: login, password, and Support Identifier The installer will start deploying the collector application You have installed the Collector Post Installation Now that you have installed successfully, the scheduler is ready to collect configuration information for the software available in your Oracle Home. By default, the first collection will take place the day after the installation. If you want to run an instrumentation script to start the configuration collection of your Oracle Database server, E-Business Suite, or Enterprise Manager, you will find more details on that in the Installation and Administration Guide for My Oracle Support Configuration Manager. Related documents available on My Oracle Support Oracle Configuration Manager Installation and Administration Guide [ID 728989.5] Oracle Configuration Manager Prerequisites [ID 728473.5] Oracle Configuration Manager Network Connectivity Test [ID 728970.5] Oracle Configuration Manager Collection Overview [ID 728985.5] Oracle Configuration Manager Security Overview [ID 728982.5] Oracle Software Configuration Manager: Disconnected Mode Collection [ID 453412.1]

    Read the article

  • Quickie Guide Getting Java Embedded Running on Raspberry Pi

    - by hinkmond
    Gary C. and I did a Bay Area Java User Group presentation of how to get Java Embedded running on a RPi. See: here. But, if you want the Quickie Guide on how to get Java up and running on the RPi, then follow these steps (which I'm doing right now as we speak, since I got my RPi in the mail on Monday. Woo-hoo!!!). So, follow along at home as I do the same steps here on my board... 1. Download the Win32DiskImager if you are on Windows, or use dd on a Linux PC: https://launchpad.net/win32-image-writer/0.6/0.6/+download/win32diskimager-binary.zip 2. Download the RPi Debian Wheezy image from here: http://files.velocix.com/c1410/images/debian/7/2012-08-08-wheezy-armel/2012-08-08-wheezy-armel.zip 3. Insert a blank 4GB SD Card into your Windows or Linux PC. 4. Use either Win32DiskImager or Linux dd to burn the unzipped image from #2 to the SD Card. 5. Insert the SD Card into your RPi. Connect an Ethernet cable to your RPi to your network. Connect the RPi Power Adapter. 6. The RPi will boot onto your network. Find its IP address using Windows Wireshark or Linux: sudo tcpdump -vv -ieth0 port 67 and port 68 7. ssh to your RPi: ssh <ip_addr_rpi> -l pi <Password: "raspberry"> 8. Download Java SE Embedded: http://www.oracle.com/technetwork/java/embedded/downloads/javase/index.html NOTE: First click accept, then choose the first bundle in the list: ARMv6/7 Linux - Headless EABI, VFP, SoftFP ABI, Little Endian - ejre-7u6-fcs-b24-linux-arm-vfp-client_headless-10_aug_2012.tar.gz 9. scp the bundle from #8 to your RPi: scp <ejre-bundle> pi@<ip_addr_rpi> 10. mkdir /usr/local, untar the bundle from #9 and rename (move) the ejre1.7.0_06 directory to /usr/local/java That's it! You are ready to roll with Java Embedded on your RPi. Hinkmond

    Read the article

  • Oracle Solaris 11.1 Announced at Oracle OpenWorld

    - by glynn
    One of the highlights for me at Oracle OpenWorld was our announcement of the next update version to Oracle Solaris 11, named Oracle Solaris 11.1. Since November 2011, we've done a lot of work not only to polish existing features and fix literally hundreds of bugs, but also add many new features that give yet more reasons for using Oracle Solaris as the deployment platform for Oracle workloads - particularly the Oracle database. Over the last few years since the Sun Microsystems acquisition, we've had our developers sitting in Redwood Shores with the Oracle database team figuring out how to best optimize that combination and provide a level of integration that no other vendor (or solution) can match. Oracle Solaris 11.1 is often the first release many customers will adopt due to perceived instability of '.0' releases. In reality, however, we've seen incredible adoption already and all our existing customers are loving the new technologies like Image Packaging System (IPS), Automated Installer and ZFS Boot Environments, consolidated network management and network virtualization, and of course the existing features that are so critical to creating private, hybrid or public cloud environments like the Oracle Solaris ZFS file system and Oracle Solaris Zones server virtualization. If you haven't already gotten on board, there's plenty chance to catch up. More importantly, Oracle Solaris 11.1 really provides a platform that is significantly easier to manage than any previous Solaris releases - to the extent that it should be relatively straightforward for any experienced Linux administrator to get up to speed (if they're struggling, we have ways to help). So take a look at what's new in Oracle Solaris 11.1 and start planning your deployment now! If you missed the announcement, you can see the full video of John Fowler's keynote at Oracle OpenWorld here:

    Read the article

  • MySQL for Excel 1.1.0 GA has been released

    - by Javier Treviño
    The MySQL Windows Experience Team is proud to announce the release of MySQL for Excel version 1.1.0 GA, one of our newest products contained in the MySQL Installer suite. You can download it from our official Downloads page at http://dev.mysql.com/downloads/installer/. The 1.1.0 release of MySQL for Excel introduces the following features: Edit MySQL Data. Edit MySQL Data This may be the coolest feature so far; users will be able to edit the data in a MySQL table using MS Excel in a very friendly and intuitive way.  Edit Data supports inserting new rows, deleting existing rows and updating existing data as easy as playing with data in an Excel’s spreadsheet and pushing changes back to the server.  Also this version contains the following bug fixes: Enabled the following checkboxes in the Append Data's Advanced Options dialog and added code in the Append Data dialog to use the checkboxes as follows: Automatically store the column mapping for the given table     If checked the current mapping will be stored automatically after clicking the Append button if the append operation is successful and there is no mapping for the current connection.schema.table already; the new mapping is stored with a proposed name of Mapping. Reload stored column mapping for the selected table automatically     If checked the first Stored Mapping found where all column names in the source grid match all column names in the target grid is automatically selected and applied when the Append Data dialog is loaded. Fixed code in Append Data that applies a stored column mapping to skip target columns where the associated mapping is empty (saved as a -1). Enclosed the Add-In's startup code in a try-catch block in order to log any possible error thrown during startup; and added information messages to the log at the beginning of the Add-In's startup code and at the end of the shutdown code.  Also changed the wrapper method that calls the MySQLUtility to write messages to the log to make logging easier, thus changed the log call throughout all the code that contains a try-catch block. Added code to the main wix configuration file to check if a newer version is already installed and if so abort the installation Fixed code to refresh the Import Procedure Form's preview grid's data source to repaint its contents every time the Call button is pressed. Added code to re-pull connections after connections are migrated from Excel to Workbench. Fixed code so when the Append Data's Automatic Mapping is performed any subsequent change on a mapping resets the mapping to a Manual Mapping. Added code to the InfoDialog class to set the button text to "Show Details" or "Hide Details" depending on the status of the Details text container. Fixed a GUID in the main wix configuration file so now previous versions are uninstalled during a new installation. Added an option to the Export Data's Advanced Options dialog to remove columns with no data, by default the Export Dialog will only flag those columns as Excluded. Added code to display a warning and paint a column red if the column name in the Export Data dialog is not set, display a warning if the table name is not set, and stack warnings but not display them if a column is Excluded, warnings are displayed normally for columns if they are not Excluded anymore.  Added code to prevent the Append and Export of Data if more than 1 selection is made (selecting more than 1 area holding the Ctrl key while selecting Excel cells). Fixed problem that prevented MySQL for Excel from loading when Display settings in Windows 7 is set to Adjust to Best Performance (Oracle bug 14521405 - UNHANDLED EXCEPTION IS THROWN WHEN LOADING MYSQL FOR EXCEL). Fixed code that renames the auto-generated Primary Key column when the Table name changes since it was not detecting if a column with the same name already existed in the table. The column duplication was not actually happening, it looked that way because the automatically generated PK column was not detecting a column had that same name. Fixed code in Export Data dialog to always set an empty string instead of null to the MySQLDataColumn properties that stores MySQL data types (MySQLDataType, RowsFrom1stDataType and RowsFrom2ndDataType). Added code to display a warning and color red a column which Data Type has not been set by the user or has been manually cleared. Added code to output to the application log exception messages consistently in all places where exceptions are catched. A series of blog posts explaining the new Edit MySQL Data feature and the other existing features are coming in this blog. You can access the MySQL for Excel documentation at http://dev.mysql.com/doc/refman/5.5/en/mysql-for-excel.html You can also post questions on our MySQL for Excel forum found at http://forums.mysql.com/. You can also post questions on our MySQL for Excel forum found at http://forums.mysql.com/. Enjoy and thanks for the support!

    Read the article

  • Transferring at a large software company: ask boss before or after?

    - by ZNZ
    Out of college I joined a large, well-known software company's consulting arm. I've gained lots of experience with some of the company's products but would like to start doing more development work rather than implementation work (traveling less would be nice, too!). The company has some product development positions that I think I could be a good fit for, but I'm unsure of how to bring it up with my manager. After a bit Googling, there are many conflicted answers on how best to handle transferring departments. When should I tell my current manager that I am interested in pursuing other positions in the company? Before or after applying?

    Read the article

  • Event system architecture for networking when performance is concerned

    - by Vandell
    How should I design a system for an action game (think in Golden Axe) where events can happen remotely? I'm using TCP for this because the client is in flash. There's so many options, I can make a binary protocol (I don't like this idea, I found it to be too hard to mantain) but I was also thinking that passing jsons through clients and server can be slow (Is that a exaggerated concern?). What about the internal architecture for the server? And for the client? I'm really lost, If it's a question that is too big, please indicate me some material so I can formulate a better question next time.

    Read the article

  • Tool to identify (and remove) unnecessary website files?

    - by xanadont
    Inevitably I'll stop using an antiquated css, script, or image file. Especially when a separate designer is tinkering with things and testing out a few versions of images. Before I build one myself, are there any tools out there that will drill through a website and list unlinked files? Specifically, I'm interested in ASP.NET MVC sites, so detecting calls to (and among many other things) @Url.Content(...) is important.

    Read the article

  • Dynamic Forms: Pattern or AntiPattern?

    - by Segfault
    I'm sure you've seen it. The database has a bunch of tables called Forms, Controls,FormsControls, ControlSets, Actions and the program that queries these tables has a dynamically generated user interface. It will read all the forms, load a home page that has links to them all, or embed them in some tabbed or paged home page, and for each of those forms it will read the various text boxes, check boxes, radio buttons, submit buttons, combo boxes, labels and whatnot from the controls and form-to-control join tables, lay those elements out according to the database and link all the controls to logic according to other rules in the database. To me, this is an anti-pattern. It actually make the application more difficult to maintain because the design of it is now spread out into multiple different systems. Also, the database is not source controlled. Sure, it may make one or two changes go more quickly, after you've analyzed the program anyway to understand how to change the data and as long as you don't stray from the sort of changes that were anticipated and accounted for, but that's often just not sustainable. What say you?

    Read the article

  • How Can I Get My USB TV Tuner To Work

    - by Foxface
    I have a KWorld UB445-U ATSC Hybrid TV Stick. I've tried MythTV, but it kept crashing when I was trying to set it up, and didn't get anywhere with it. I've tried VLC and just tried Kaffiene. I'm not sure how to work VLC or Kaffeine to accept my TV. Can someone help me with it? EDIT: Code: foxface@Toshiba-Satellite-L775:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b289 Chicony Electronics Co., Ltd Bus 002 Device 006: ID 1b80:e421 Afatech Bus 003 Device 002: ID 13fd:1e40 Initio Corporation

    Read the article

  • how to access inaccessible mac os x hard drive via ubuntu

    - by jon
    Background: My intention was to load a Virtual Machine (VM) on my Mac OS X Snow Leopard. My Mac had just enough room for a VM (my thought process was that VM was the same as partition) However, I burned the newest version of Ubuntu onto a CD, thinking that partitioning and running a virtual machine would be the same. I would restart my computer, booting up Ubuntu installer. The installation would not allow me to partition, forcing me to force shutdown my laptop. when I turn on my laptop, I see that my computer is "missing operating system". So, can someone help me fix my a) bootcamp, b) getting files and if a and b are fixed c) to install ubuntu as a VM?

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >