Daily Archives

Articles indexed Thursday August 21 2014

Page 1/19 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• What is the correct iptables rule when NATing multiple private subnets?

  - by Jose Mendez

  I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

  Read the article

• Does stunnel prevent non ssl traffic to "the" specified port?

  - by user432024

  So say I have an arbitrary tcp port 12345 and it's non ssl and I want to put stunnel to secure traffic to it. When stunnel is in front of it does it mean that this port is now tls/ssl only? Or can you still connect to it unencrypted? Basically I want to make sure that this port can only be accessed through ssl/tls and stunel and no other way. Clarification I want to make sure only stunnel port is open. Which is answered in the comments that the unsecured port should be fire-walled but preferably bound to localhost.

  Read the article

• How to trigger cross-platform jobs between Windows and Unix

  - by andyb

  I have an application which has components on Windows and Unix. I need to run overnight jobs which initiate tasks/jobs on both environment. These need to be sequenced so I cannot simple use Cron / Task Scheduler. For each job, there will be a controlling script either on Windows or Unix, but this script will need to initiate jobs on the other environment and detect when they are complete and a success/failure code. In the past I have achieved this using 'flag files' on a samba share. This worked but required 'polling' behaviour on the receiving end which I do not consider optimal. I would prefer not to have to embed user credentials in script if possible.

  Read the article

• How to create a snapshot volume to a remote server using kvm?

  - by Purres

  I want to backup a few virtual machines to a backup server. Here're the backup steps. suspend a virtual machine create a snapshot of the virtual machine using lvcreate -s resume a virtual machine dd if=/virtual_machine_path | lzop > /temp/backup.lzo rsync /temp/backup.lzo -e "ssh " 1.2.3.4:/backup_path/ However, the hypervisor server doesn't have enough hard disk space to create a snapshot in step 2. Is there a way to create a logical volume snapshot to a remote server?

  Read the article

• Disable remote session timeout on Win Server 2012 R2

  - by Sarchophagi

  For botting purposes, I have to keep my Win Server 2012 R2 running without logging-off after I disconnect from Remote Session. Found information about it here: http://technet.microsoft.com/en-us/library/cc754272.aspx but I just its for Win Server 2008 and doesn't seem to work on 2012 version. Could you guys help me setting infinite timout? EDIT: Tried this answer Changing the login timeout for Windows Remote Desktop Services but without results.. MORE DETAIL ABOUT WHAT I NEED: I connect to Amazon ECL Istance with "Remote Desktop Conection". I need to put remote server to keep running as if an user was normally remotely logged in, and prevent it from going to that log-out stand-by screen, usually blue coloured @ winserver2012, because i'm using macros that take screenshots of screen and find bitmap positions, do clicks, move mouse and stuff..

  Read the article

• DRS: Unknown JNLP Location

  - by Joe

  We are using Deployment Rule Sets to limit access to the older JRE to well-known applications like - but are running into a problem. One business critical applications has the following properties (*s to protect info): title: Enterprise Services Repository location: null jar location: http://app.*.com:52400/rep/repository/*.jar jar version: null isArtifact: true The application downloads a .jnlp file, and uses java web start to execute. Since the location is null, this application cannot be targeted by a location rule. And the certificate hash method only works when the application is cached (being ran more than once). If cache storing is off, which is the case in some situations, how can this application be targeted? Or at least told to run with an older JRE on start? This problem is specifically noted in this bug Thanks!

  Read the article

• Automatically Kill/Restart Process(es) When Memory is Critically Low

  - by nemesisfixx

  I have a Debian Wheezy VPS box where am running a couple of Django apps in production. Ideally, would have tried addressed my current memory footprint issues by optimizing the apps, adding more RAM or augmenting with Swap. But the problem is that I doubt there's much memory optimization I'd milk from optimizing the Django apps (the stack being open-source and robust), and adding RAM is a cost constraint for me (this is a remote VPS), also, the host doesn't offer options to use Swap! So, in the meantime (as I wait to secure more resources to afford more RAM), I wish to mitigate the scenarios where the server runs out memory so that I just have to request a VPS restart (as in, at that point, I can't even SSH into the box!). So, what I would love in a solution is the ability to detect when a process (or generally, total system memory usage) exceeds a certain critical amount (for now, example the FREE RAM falls to say 10%) - which I've noticed occurs after the VPS's been up for long, and when also traffic is suddenly much to some of the heavy apps (most are just staging apps anyway). So, I wish to be able to kill/restart the offending process(es) - most likely Apache. Which solution when done manually in these situations has restored sane memory usage levels - a hint that possibly one or more of the Django apps has a memory leak? In brief: Monitor overall system RAM usage When FREE RAM falls below a given critical threshold (say below 10%), kill/restart the offending process(es) - or simpler, if we assume from my current log analysis (using linux-dash) that Apache is often the offender, then kill/restart it. Rinse and repeat...

  Read the article

• Is it possible to create a read-only user account for security auditing purposes?

  - by user2529583

  An organization requires several administrators to have a role of a security auditor. They must have read-only (via network/remote) access to Windows Server 2008 / R2 systems and have permissions to view the server configuration. They must not be able to make any other changes to the server or the network, like restarting or making any configuration chanages. However I can't find any built-in settings for a user like this. The closest thing is the "Users" user group [1], however from my understanding every user in the domain is in this group and cannot view the domain server's configuration. So, what are other options of implementing a read-only user account in Windows Server 2008? [1] http://technet.microsoft.com/en-us/library/cc771990.aspx

  Read the article

• Munin not creating HTML files in Ubuntu Server 14.04

  - by lepe

  I have used munin in several servers and this is the first time is taking me so much time to set it up. When I telnet munin directly, I can list the services, there is no error at the logs and munin its being updated every 5 minutes. However no html files are created. I'm using the default location (/var/cache/munin/www) and I can confirm the permissions of that directory are set to munin.munin (IP and domain has been changed) munin.conf: dbdir /var/lib/munin htmldir /var/cache/munin/www logdir /var/log/munin rundir /var/run/munin [example.com;] address 100.100.50.200 munin-node.conf: log_level 4 log_file /var/log/munin/munin-node.log pid_file /var/run/munin/munin-node.pid background 1 setsid 1 user root group root host_name example.com allow ^127\.0\.0\.1$ allow ^100\.100\.50\.200$ allow ^::1$ /etc/hosts : 100.100.50.200 example.com 127.0.0.1 localhost $ telnet example.com 4949 Trying 100.100.50.200... Connected to example.com. Escape character is '^]'. # munin node at example.com list apache_accesses apache_processes apache_volume cpu cpuspeed df df_inode entropy fail2ban forks fw_packets if_err_eth0 if_err_eth1 if_eth0 if_eth1 interrupts ipmi_fans ipmi_power ipmi_temp irqstats load memory munin_stats mysql_bin_relay_log mysql_commands mysql_connections mysql_files_tables mysql_innodb_bpool mysql_innodb_bpool_act mysql_innodb_insert_buf mysql_innodb_io mysql_innodb_io_pend mysql_innodb_log mysql_innodb_rows mysql_innodb_semaphores mysql_innodb_tnx mysql_myisam_indexes mysql_network_traffic mysql_qcache mysql_qcache_mem mysql_replication mysql_select_types mysql_slow mysql_sorts mysql_table_locks mysql_tmp_tables ntp_2001:e40:100:208::123 ntp_91.189.94.4 ntp_kernel_err ntp_kernel_pll_freq ntp_kernel_pll_off ntp_offset ntp_states open_files open_inodes postfix_mailqueue postfix_mailvolume proc_pri processes swap threads uptime users vmstat fetch df _dev_sda3.value 2.1762874086869 _sys_fs_cgroup.value 0 _run.value 0.0503536980635825 _run_lock.value 0 _run_shm.value 0 _run_user.value 0 _dev_sda5.value 0.0176986285727571 _dev_sda8.value 1.08464646179852 _dev_sda7.value 0.0346633563514803 _dev_sda9.value 6.81031810822797 _dev_sda6.value 9.0932802215469 . /var/log/munin/munin-node.log Process Backgrounded 2014/08/16-14:13:36 Munin::Node::Server (type Net::Server::Fork) starting! pid(19610) Binding to TCP port 4949 on host 100.100.50.200 with IPv4 2014/08/16-14:23:11 CONNECT TCP Peer: "[100.100.50.200]:55949" Local: "[100.100.50.200]:4949" 2014/08/16-14:36:16 CONNECT TCP Peer: "[100.100.50.200]:56209" Local: "[100.100.50.200]:4949" /var/log/munin/munin-update.log ... 2014/08/16 14:30:01 [INFO]: Starting munin-update 2014/08/16 14:30:01 [INFO]: Munin-update finished (0.00 sec) 2014/08/16 14:35:02 [INFO]: Starting munin-update 2014/08/16 14:35:02 [INFO]: Munin-update finished (0.00 sec) 2014/08/16 14:40:01 [INFO]: Starting munin-update 2014/08/16 14:40:01 [INFO]: Munin-update finished (0.00 sec) $ ls -la /var/cache/munin/www/ drwxr-xr-x 3 munin munin 19 Aug 16 13:55 . drwxr-xr-x 3 root root 16 Aug 16 13:54 .. drwxr-xr-x 2 munin munin 4096 Aug 16 13:55 static Any ideas on why it is not working? EDIT This is how /var/log/munin/ log looks like after some days: -rw-r----- 1 www-data 0 Aug 16 13:54 munin-cgi-graph.log -rw-r----- 1 www-data 0 Aug 16 13:54 munin-cgi-html.log -rw-rw-r-- 1 munin 0 Aug 16 13:55 munin-html.log -rw-r----- 1 munin 0 Aug 19 06:18 munin-limits.log -rw-r----- 1 munin 15K Aug 18 14:10 munin-limits.log.1 -rw-r----- 1 munin 1.8K Aug 18 06:15 munin-limits.log.2.gz -rw-rw-r-- 1 munin 1.3K Aug 17 06:15 munin-limits.log.3.gz -rw-r--r-- 1 root 6.5K Aug 16 13:55 munin-node-configure.log -rw-r--r-- 1 root 0 Aug 17 06:18 munin-node.log -rw-r--r-- 1 root 420 Aug 16 14:52 munin-node.log.1.gz -rw-r----- 1 munin 0 Aug 19 06:18 munin-update.log -rw-r----- 1 munin 11K Aug 18 14:10 munin-update.log.1 -rw-r----- 1 munin 1.6K Aug 18 06:15 munin-update.log.2.gz -rw-rw-r-- 1 munin 1.5K Aug 17 06:15 munin-update.log.3.gz

  Read the article

• Unable to remove "Run this program as an administrator" (greyed out) with Excel 2010

  - by Sean Hu

  I have issue with one of the user in Terminal Server 2008 R2 who has "Run this program as an administrator" checked and greyed out with Excel 2010. This causes UAC to popup requesting for administrator credential whenever user want to start excel. I found in excel 2010 properties Compatibility tab "Run this program as an administrator" is checked and greyed out (Unable to make any change) This issue only occurs in Excel 2010, all other Office programs does not has this option checked and greyed out. Currently UAC is set to Default (Second level to top) Other users in terminal server do not have "Run this program as an administrator" checked and it is NOT greyed out. The user who has issue is in the same group and has the setting as other users who doesn't has the issue in AD. Could anyone advise me how could I remove this "Run this program as an administrator" in option in Excel 2010? Thank you.

  Read the article

• How to test email spam scores with amavis?

  - by CaptSaltyJack

  I'd like a way to test a spam message to see its spam scores that SpamAssassin gives it. The SA db files (bayes_toks, etc) reside in /var/lib/amavis/.spamassassin. I've been testing emails by doing this: sudo su amavis -c 'spamassassin -t msgfile' Though this yields some strange results, such as: Content analysis details: (3.7 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 3.5 BAYES_99 BODY: Bayes spam probability is 99 to 100% [score: 1.0000] -0.0 NO_RELAYS Informational: message was not relayed via SMTP 0.0 LONG_TERM_PRICE BODY: LONG_TERM_PRICE 0.2 BAYES_999 BODY: Bayes spam probability is 99.9 to 100% [score: 1.0000] -0.0 NO_RECEIVED Informational: message has no Received headers 0.2 is an awfully low scores for BAYES_999! But this is the first time I've used amavis, previously I've always just used spamassassin directly as a content filter in postfix, but apparently running amavis/spamassassin is more efficient. So, with amavis in the picture, how can I run a test on a message to see its spam score breakdown? Another email I ran a test on got this result: 2.0 BAYES_80 BODY: Bayes spam probability is 80 to 95% [score: 0.8487] Doesn't make sense, that BAYES_80 can yield a higher score than BAYES_999. Help!

  Read the article

• What are the pros/cons of blocking a program from running in %appdata%, %temp%, etc.?

  - by poke

  While researching ways to prevent CryptoLocker, I saw a forum post that advised using Group Policy Objects (GPO) and/or antivirus software to block run access in the following locations: %appdata% %localappdata% %temp% %UserProfile% Compressed archives Obviously, anything written in a forum should be taken with caution. I do see advantages to do doing this, though, primarily because malware likes to execute out of these locations. Of course, this could impact legitimate programs as well. What are the drawbacks to blocking run access to these locations? What are the advantages?

  Read the article

• Openswan + xl2tpd connections time out after a while

  - by Halfgaar

  I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

  Read the article

• Ingress filtering in Linux traffic control: Redirect traffic to IFB device

  - by Dani Camps

  I have an openwrt router and I want to shape incoming traffic in order to classify all the traffic addressed to a certain IP address in my home network as low priority. For that purpose I want to redirect all traffic incoming to the eth1 interface, the one connected to the DSL modem, to an IFB device where I will do the shaping. These are the details of my system: Linux OpenWrt 2.6.32.27 #7 Fri Jul 15 02:43:34 CEST 2011 mips GNU/Linux Here is the script I am using where the last instruction is failing: # Variable definition ETH=eth1 IFB=ifb1 IP_LP="192.168.1.22/32" DL_RATE="900kbps" HP_RATE="890kbps" LP_RATE="10kbps" TC="tc" # Configuring the ifbX interface insmod ifb insmod sch_htb insmod sch_ingress ifconfig $IFB up # Adding the HTB scheduler to the ingress interface $TC qdisc add dev $IFB root handle 1: htb default 11 # Set the maximum bandwidth that each priority class can get, and the maximum borrowing they can do $TC class add dev $IFB parent 1:1 classid 1:10 htb rate $LP_RATE ceil $DL_RATE $TC class add dev $IFB parent 1:1 classid 1:11 htb rate $HP_RATE ceil $DL_RATE # Redirect all ingress traffic arriving at $ETH to $IFB $TC qdisc del dev $ETH ingress 2>/dev/null $TC qdisc add dev $ETH ingress $TC filter add dev $ETH parent ffff: protocol ip prio 1 u32 \ match u32 0 0 flowid 1:1 \ action mirred egress redirect dev $IFB The last instruction fails with: Action 4 device ifb1 ifindex 9 RTNETLINK answers: No such file or directory We have an error talking to the kernel Does anyone know what am I doing wrong ? Best Regards Daniel

  Read the article

• ForwardAgent in Jenkins

  - by r_2

  I'm trying to enable ForwardAgent in the "Publish over SSH" Jenkins Plugin. This would allow jenkins to execute deployments, rsyncs and svn+ssh checkouts on remote servers. But there's no option for this in the GUI. ForwardAgent is set to yes in /etc/ssh/ssh_config and in /var/lib/jenkins/.ssh/config, but when Jenkins jobs login over ssh, the remote session does not have the key loaded in agent. ("Could not open a connection to your authentication agent.") Is there a way to force ForwardAgent, or a better way to do this (via a Jenkins slave)? Thanks for any ideas, much appreciated!

  Read the article

• I get a Segmentation fault when doing apt-get util-linux

  - by Adam

  I've found that a lot of upgrade commands and Apache on my system are failing with Segmentation faults. I don't know if this is the main one, but a lot of packages depend on util-linux: root@myUbuntuHardyHeronServer:~# apt-get install util-linux Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: util-linux 1 upgraded, 0 newly installed, 0 to remove and 72 not upgraded. 20 not fully installed or removed. Need to get 0B/441kB of archives. After this operation, 0B of additional disk space will be used. (Reading database ... 20547 files and directories currently installed.) Preparing to replace util-linux 2.13.1-5ubuntu2 (using .../util-linux_2.13.1-5ub untu3.1_i386.deb) ... Unpacking replacement util-linux ... Segmentation fault dpkg: warning - old post-removal script returned error exit status 139 dpkg - trying script from the new package instead ... Segmentation fault dpkg: error processing /var/cache/apt/archives/util-linux_2.13.1-5ubuntu3.1_i386 .deb (--unpack): subprocess new post-removal script returned error exit status 139 Segmentation fault dpkg: error while cleaning up: subprocess post-removal script returned error exit status 139 Errors were encountered while processing: /var/cache/apt/archives/util-linux_2.13.1-5ubuntu3.1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• SQL Server Maintenence Plan error on an offline Database

  - by Sean Earp

  Today is SQL day for me :) I have a maintenance plan that is failing to run with the following error: Failed:(-1073548784) Executing the query "USE [SharedServices1_DB]" failed with the following error: "Database 'SharedServices1_DB' cannot be opened because it is offline.". Possible failure reasons: Problems with the query, "ResultSet" property not set correctly, parameters not set correctly, or connection not established correctly. where SharedServices1_DB is a database that is set to offline. I would like to exclude this database from the maintenance plan, but when the database is offline, it does not show up at all as a "specific database" in the maintenance plan task, and if I bring it online, it is already unchecked in the maintenance plan task. How can I exclude an offline database from a maintenance plan?

  Read the article

• Can I use excel to read barcodes and take me to a specific cell?

  - by Ben

  I work for a community group that holds an annual fund raiser for charity over a weekend. I am an excel user and am wanting to set it up so that I can assign a barcode on a card to a specific person. My hope is to be able to scan the barcode have it take me to a specific cell in the spread sheet so I can update the Commitment amount. and provide as much anonymity for our donors as possible. Can this even be done?

  Read the article

• Python coding with VLC player (quite a basic query I expect)

  - by Todd

  I'm fairly new to the whole coding realm so my knowledge is fairly limited, and I can't seem to find any basic tutorials on how to use scripts with VLC player. More specifically, the reason I'm asking here is because I stumbled across a post on this site about playing random clips from random videos on VLC player automatically. This is the forum post: Playback random section from multiple videos changing every 5 minutes My situation is similar to this lovely gentleman's was, though he clearly knows a lot more about coding than I do. In short, I'd like to copy this coding into a file of some sort and apply it to VLC player myself. Only I'm not sure what file type I'd have to save it as (I have Python by the way, and I tried saving it as a .py file but I didn't know if it was correct or where to go from there). Additionally, I'm not sure how to get VLC to "read" the script, so to speak - is there a specific location the file needs to be, and do I run the script from another program or through VLC? I'll reiterate that I'm relatively new to this, so if anybody would be so kind as to post a quick list of steps on how to save/place the file and use it with VLC player I really would appreciate it! P.S. I'm not computer illiterate, I'm fine with most programs and I'd understand if you just said things like "C:\Program Files (x86)\VideoLAN\VLC\plugins" or "in VLC, select Tools Plugins and extensions", I just wouldn't catch on to anything about adding a line of coding that does something without being told exactly what to write! Many thanks in advance! :) Todd

  Read the article

• What do you upgrade to make games load faster? [on hold]

  - by Superbest

  Let's say you have a relatively modern game like Shogun 2. The loading screens take several minutes. This bothers you and you'd like to improve it. What is actually going on when loading screens are up? I'm guessing assets are being loaded into memory from disk, and possibly being decompressed first. However, what is actually causing the slow down? The memory? Mainboard? CPU? HDD? If you had $100 to spend on upgrades and your only goal is to speed up loading screens without reducing other performance, what component of the computer does it make sense to upgrade for maximum benefit? If your answer is "it depends on the existing setup", what sort of benchmarks would you run to determine what is causing the bottleneck? What if you had $500 instead? I give the two budgets for context. I am not asking for actual recommendations about which component to buy (nor are the numbers supposed to be rigid limits), but what features are important when shopping for components with small and large budgets (a large budget could allow buying multiple components which are not so good on their own, but work particularly well together). I mention Shogun 2 as an example, but I'm asking about reducing overall loading times, across all games, not just one game. Therefore, "put it on a solid state disk" probably won't be good solution, because putting every game on your SDD will quickly fill it up.

  Read the article

• ctrl+c ctrl+v do notwork on any program [duplicate]

  - by David

  This question is an exact duplicate of: Windows won't ctrl+c and ctrl+v I have this problem, ctrl+c and ctrl+v never work for anything no matter what, and if I do it a few times it won't let me type at all, I found if I went to accessories/accessibility and click "on-screen keyboard" and then I can type, but I still can't use ctrl+c ctrl+v..what's wrong!?!?

  Read the article

• Why can`t we treat SSL Certs like Pgp keys instead of trusting CAs?

  - by yarun can

  I am dumb and stupid and I do not know all the technical aspects of SSL and server/client side implications and implementations. However I understand them good enough from user point of view to use SSL and encyrption daily. I was thinking that how silly it is to trust some unknown/known CAs when it comes to our our certificates for our servers. There had been many cases of misconduct, misuse, compromises and theft of certificates/ca keys from those places. On top of those known issues we also have to pay these guys regularly. I am wondering why can not we use/treat web server certificates like we use our pgp keys? So I sign a SSL certificate and send to a central server. And then each user accessing my site checks the validity and the keys from some central server (like pgp key servers). Is this a stupid idea? If so what could be a better idea than current system of issuing valid certificates. I am looking for a better than more secure idea. Naturally this is not a solution to an existing problem, rather it will be a hypothetical solution for some future implementation of a currently messed up web of trust on the internet due to recent news about NSA and their criminal buddies around the world. thanks

  Read the article

• Need help diagnosing my machine

  - by Tom Collins

  I have something that just slows my computer to a crawl sometimes. Not running anything big. Yesterday all I had running (besides background apps) were Firefox & Windows Explorer and could barely even switch screens. Nothing showing up in the task manager as hogging CPUs. I have all non-essential services stopped (MySQl & MSSQL) unless I need them. I made some restore points not long ago, but they disappeared. This is a development mach with a LOT of apps installed, so I really, really do not want to re-install Windows. So, what I'm looking for are ideas or tools I can use to help diagnose this problem. The only clues I have is this started right after I installed Office 2013 (with Office 2010 still installed as well) installed Visual Studio 2012 (also keeping 2010 as a co-install) and installed MSSQL 2012 (upgrade from 2008, no co-install) Also, computer runs fine in Safe Mode. I've just ran out of ideas of what to check. Any help / suggestions would much appreciated. Thanks P.S. I'm running Win 7 Pro (x64). Office is also 64 bit. Visual Studio & MSSQL are 64 bit if that option was available (not sure).

  Read the article

• Lightning strike causes fast download?

  - by blaine

  Ok, REALLY strange question. My friend says he was downloading a 14 GB file at about 1 mb/s when suddenly there was a lightning strike outside and momentarily the download speed jumped to 10,000,000 GB/s. The file finnished downloading. He even has the screenshot to prove it. I also trust him and don't believe that he would be lying. So my question is: how is this even possible?? Is there just the possibility that the file was about to finish downloading anyway and the lightning strike coincided with a freak download speed calculation error?

  Read the article

• Networking Home Office

  - by Matt

  I'm in the process of building an office in my garden. It's about 25m away from my house. I'd like to run a wired network connection to the office. I'd rather not go down the powerline route, as speeds don't seem great, and I'm likely to want to be moving a lot of data around on the internal network. I have an electrician who is running armoured electrical cable to the office, and is providing conduit for me to run network cable. My questions are: 1) What type of cable to run 2) How I terminate/connect it at both ends I could get something like armoured cat6 utp solid core (like this: http://www.netstoredirect.com/cat6-cable/289166-external-armoured-cat6-utp-solid-cable-price-per-metre.html) which seems fairly robust, but then I have to terminate it. Additionally, where the cable enters my house, there is about another 15m to where my router is situated. I also read this artice: http://www.audioholics.com/audio-video-cables/bjc-cat-network-cable-quality-interview which scared me into realising I don't know what I'm doing!! particularly with termination. Or I could get an "cat6 external patch cable" (e.g http://www.netstoredirect.com/rj45-network-cables/239231-external-cat6-utp-ldpe-rj45-patch-leads.html) and run that in the conduit, and work out how to terminate it at the house end. At the office end I guess I can just plug it into a switch. Any help? Thanks

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >