Monthly Archives

Articles indexed in February 2011

Page 11/314 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• ATI graphics card overriding onboard Intel graphics

  - by Patrick

  I have an ATI graphics card with an AGP connection and a DVI port, and an Intel graphics processor on the motherboard with a VGA port. I have two monitors. When the graphics card is unplugged, I get this from lspci: 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) When it is attached, I get this: 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10) 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] 01:00.1 Display controller: ATI Technologies Inc RV380 [Radeon X600] Note the absence of 00:02.0 - this is apparently causing the VGA monitor to say "No Signal" and the only the DVI display to show up in the list. I checked for problems in xorg.conf... there isn't one. I have no idea how to build one.

  Read the article

• What are my options for sharing music between Windows & Ubuntu on the same network?

  - by jgbelacqua

  We have a few Windows(XP & 7) and Ubuntu machines in the house sharing a wireless connection, and want to share music between them. If possible, I would like to be able to serve music from both Windows and Ubuntu (but it doesn't have to be the same time). I don't know much about sharing folders or streaming, but I'm guessing both would be options (that is, using a local client to access a shared song or a local client to access a shared stream). I want to be able to share the music between the systems as simply as possible. Bonus points (but not requirements) for cross-platform -- same application on both Windows and Ubuntu? available on startup (via daemon or autostart or whatnot) open source More info: All systems have dynamic addresses (DHCP) supplied from the ISP-supplied wireless router. There are several Gigabytes of music on one Windows XP box and one Ubuntu 10.10 The music is not well-sorted (I'm thinking this might have an impact on UI usability). Only has to be available internally (private address space behind the wireless router) bandwidth is not a problem We don't have (legitimate) admin access to the wireless router

  Read the article

• How do I get long command lines to wrap to the next line?

  - by BrianH

  Edit It was my .bashrc file. I've copied the same profile from machine to machine, and I used special characters in my $PS1 that are somehow throwing it off. I'm now sticking with the standard bash variables for my $PS1. Thanks to @ændrük for the tip on the .bashrc! ...End Edit... Something I have noticed in Ubuntu for a long time that has been frustrating to me is when I am typing a command at the command line that gets longer (wider) than the terminal width, instead of wrapping to a new line, it goes back to column 1 on the same line and starts over-writing the beginning of my command line. (It doesn't actually overwrite the actual command, but visually, it is overwriting the text that was displayed). It's hard to explain without seeing it, but let's say my terminal was 20 characters wide (Mine is more like 120 characters - but for the sake of an example), and I want to echo the English alphabet. What I type is this: echo abcdefghijklmnopqrstuvwxyz But what my terminal looks like before I hit the key is: pqrstuvwxyzghijklmno When I hit enter, it echos abcdefghijklmnopqrstuvwxyz so I know the command was received properly. It just wrapped my typing after the "o" and started over on the same line. What I would expect to happen, if I typed this command in on a terminal that was only 20 characters wide would be this: echo abcdefghijklmno pqrstuvwxyz Background: I am using bash as my shell, and I have this line in my ~/.bashrc: set -o vi to be able to navigate the command line with VI commands. I am currently using Ubuntu 10.10 server, and connecting to the server with Putty. In any other environment I have worked in, if I type a long command line, it will add a new line underneath the line I am working on when my command gets longer than the terminal width and when I keep typing I can see my command on 2 different lines. But for as long as I can remember using Ubuntu, my long commands only occupy 1 line. This also happens when I am going back to previous commands in the history (I hit Esc, then 'K' to go back to previous commands) - when I get to a previous command that was longer than the terminal width, the command line gets mangled and I cannot tell where I am at in the command. The only work-around I have found to see the entire long command is to hit "Esc-V", which opens up the current command in a VI editor. I don't think I have anything odd in my .bashrc file. I commented out the "set -o vi" line, and I still had the problem. I downloaded a fresh copy of Putty and didn't make any changes to the configuration - I just typed in my host name to connect, and I still have the problem, so I don't think it's anything with Putty (unless I need to make some config changes) Has anyone else had this problem, and can anyone think of how to fix it? Thanks in advance! Brian

  Read the article

• no volume in kubuntu 10.04

  - by neha

  hello,I am having both gnome and kde on my system.as my gnome is working perfectly but in KDE is there is no sound being generated. output of apley -l and lspci commands is as follows.. neha@neha-laptop:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 3: INTEL HDMI [INTEL HDMI] Subdevices: 1/1 Subdevice #0: subdevice #0 and output of lspci command is: neha@neha-laptop:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 02:09.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 12) 02:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) 02:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff) 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12) 0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01) can anyone help me??

  Read the article

• How to automatically change volume level when un-/plugging headphones?

  - by htorque

  What I want is the following: When I plug in my headphones, I want the sound to be un-muted and set to a specific volume level. When I unplug my headphones, I want the sound to be muted (or set to a specific volume level). Setting the volume levels isn't the problem, but I somehow need to do this when un-/plugging the headphones, so I'm looking for a way to get notified of those events. I quickly found /proc/asound/card0/codec#0 to indicate whether headphones are plugged in or not, so I tried to monitor it using inotifywait and change the volume level based on modified notifications. Unfortunately inotifywait failed because proc isn't an ordinary filesystem. Are there other ways to do this (maybe via PulseAudio)? Audio device: Intel HDA, audio codec: Conexant CX20585.

  Read the article

• How do I pin a particular MySQL version to avoid unnecessary upgrades?

  - by asparagino

  I'm running a MySQL server, and want to keep it up to date with regular apt-upgrades. I don't want this to cause MySQL to upgrade unless I'm doing it during scheduled downtime! How do I alter my apt-preferences so that this won't happen? I've tried adding this to a file as /etc/apt/preferences.d/pin-mysql Package: mysql-client-5.1 Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 Package: mysql-client-core-5.1 Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 Package: mysql-common Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 Package: mysql-server Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 Package: mysql-server-5.1 Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 Package: mysql-server-core-5.1 Pin: version 5.1.41-3ubuntu12.7 Pin-Priority: 1001 That then states the packages are pinned with "apt-cache policy" outputting: ... all package sources here 500 http://security.ubuntu.com/ubuntu/ lucid-security/universe Packages release v=10.04,o=Ubuntu,a=lucid-security,n=lucid,l=Ubuntu,c=universe origin security.ubuntu.com 500 http://security.ubuntu.com/ubuntu/ lucid-security/restricted Packages release v=10.04,o=Ubuntu,a=lucid-security,n=lucid,l=Ubuntu,c=restricted origin security.ubuntu.com ... etc Pinned packages: mysql-server -> 5.1.41-3ubuntu12.7 mysql-server-core-5.1 -> 5.1.41-3ubuntu12.7 mysql-client-core-5.1 -> 5.1.41-3ubuntu12.7 mysql-common -> 5.1.41-3ubuntu12.7 mysql-server-5.1 -> 5.1.41-3ubuntu12.7 mysql-client-5.1 -> 5.1.41-3ubuntu12.7 However... running aptitude safe-upgrade just updated MySQL... what am I doing wrong?

  Read the article

• How should I synchronize configurations and data across computers?

  - by lfaraone

  Imagine I have three Ubuntu computers home, laptop, beach-house. They all have the same version of Ubuntu, 10.04 installed, and are kept up to date from the repositories. I use f-spot, thunderbird, and google-chrome on all of the computers. Is there a way to keep the data and configuration in sync across them, without requiring constant connectivity for normal (non-synchronous) usage? For example, they should be usable without network connectivity, so something like NFS won't work. An ideal solution would not require manual action to start the syncing process.

  Read the article

• permanently load module

  - by Radu

  I have a Compaq Presario CQ-61 320SQ, I am using Ubuntu 10.04 because after update to 10.10 my mouse and touchpad won't work, network won't work, sound won't work ... (I managed to fix most of them after almost a month of googling, but not all, my 2 Desktops have no problem with 10.10) so I decided to switch back to 10.04, where I have a problem: My broadband speed is very low beacause of the kernel module r8169, I downloaded the good module r8101 and every time the computer boots have a rc.local entry to fix this. Question: Can I load the modul permanently from a specific location. I heard about /etc/modules but there I need the module name, but I have to load it from a specific path (where is the default path for that) Thank you. So I studied the script: It creates the file r8101.ko in /lib/modules/uname -r/kernel/drivers/net so I think as long as nobody will delete that file, and I don't update the kernel, maybe adding r8108 to /etc/modules will work, and add r8169 to blacklist ... I will give it a try. EDIT2: So I added r8101 to /etc/modules and blacklist r8169 to /etc/modprobe.d/blacklist.conf It still uses the old module, lsmod prints: radu@adu:~$ lsmod | grep r8 r8101 67626 0 r8169 34108 0 mii 4381 1 r8169 EDIT: the module is loaded using this script that came with it: #!/bin/sh # invoke insmod with all arguments we got # and use a pathname, as insmod doesn't look in . by default TARGET_PATH=/lib/modules/`uname -r`/kernel/drivers/net echo echo "Check old driver and unload it." check=`lsmod | grep r8169` if [ "$check" != "" ]; then echo "rmmod r8169" /sbin/rmmod r8169 fi check=`lsmod | grep r8101` if [ "$check" != "" ]; then echo "rmmod r8101" /sbin/rmmod r8101 fi echo "Build the module and install" echo "-------------------------------" >> log.txt date 1>>log.txt make all 1>>log.txt || exit 1 module=`ls src/*.ko` module=${module#src/} module=${module%.ko} if [ "$module" == "" ]; then echo "No driver exists!!!" exit 1 elif [ "$module" != "r8169" ]; then if test -e $TARGET_PATH/r8169.ko ; then echo "Backup r8169.ko" if test -e $TARGET_PATH/r8169.bak ; then i=0 while test -e $TARGET_PATH/r8169.bak$i do i=$(($i+1)) done echo "rename r8169.ko to r8169.bak$i" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak$i else echo "rename r8169.ko to r8169.bak" mv $TARGET_PATH/r8169.ko $TARGET_PATH/r8169.bak fi fi fi echo "Depending module. Please wait." depmod -a echo "load module $module" modprobe $module echo "Completed." exit 0

  Read the article

• Flash 10.2 RC + Crystal HD for HW accelerated video on Ubuntu

  - by Gee

  I have a netbook with a N450 Atom and a BCM70012 aka Crystal HD card. On Windows 7 I can play HD flash video with very little CPU usage because of the RC of Flash 10.2. I did some reading and saw posts claiming that the Crystal HD card is finally supported by the newer Flash 10.2 RC in Ubuntu but I can't get it to work. I can confirm that flash 10.2 is loaded and used, and there's even a HW acceleration option that is enabled in the settings but performance is horrible. From what I read, the Crystal HD card is supposed to be enabled on 10.10 by default - I don't know if it is. I tried installing drivers for it in various ways but HD flash video is still a slideshow So does anyone have it working? If so, how'd you set it up?

  Read the article

• How do I stop icons appearing on the desktop in a particular area?

  - by Seamus

  When I download something to my desktop, or insert a CD or flash drive, the icon appears on my desktop. When I have conky running, the icon sometimes appears in the top right corner, underneath conky; where I can't see it. How do I stop this happening? My .conkyrc is pasted below. I didn't write it all myself, so I'm not entirely sure what I need to change, or what parts are relevant for this particular question... # UBUNTU-CONKY # A comprehensive conky script, configured for use on # Ubuntu / Debian Gnome, without the need for any external scripts. # # Based on conky-jc and the default .conkyrc. # INCLUDES: # - tail of /var/log/messages # - netstat shows number of connections from your computer and application/PID making it. Kill spyware! # # -- Pengo # # Create own window instead of using desktop (required in nautilus) own_window yes own_window_type override own_window_transparent yes own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager # Use double buffering (reduces flicker, may not work for everyone) double_buffer yes # fiddle with window use_spacer right # Use Xft? use_xft yes xftfont DejaVu Sans:size=8 xftalpha 0.8 text_buffer_size 2048 # Update interval in seconds update_interval 3.0 # Minimum size of text area # minimum_size 250 5 # Draw shades? draw_shades no # Text stuff draw_outline no # amplifies text if yes draw_borders no uppercase no # set to yes if you want all text to be in uppercase # Stippled borders? stippled_borders 3 # border margins border_margin 9 # border width border_width 10 # Default colors and also border colors, grey90 == #e5e5e5 default_color grey own_window_colour brown own_window_transparent yes # Text alignment, other possible values are commented #alignment top_left alignment top_right #alignment bottom_left #alignment bottom_right # Gap between borders of screen and text gap_x 10 gap_y 20 # stuff after 'TEXT' will be formatted on screen TEXT $color ${color orange}SYSTEM ${hr 2}$color $nodename $sysname $kernel on $machine ${color orange}CPU ${hr 2}$color ${freq}MHz Load: ${loadavg} Temp: ${acpitemp} $cpubar ${cpugraph 000000 ffffff} NAME ${goto 150}PID ${goto 200}CPU% ${goto 250}MEM% ${top name 1} ${goto 150}${top pid 1} ${goto 200}${top cpu 1} ${goto 250}${top mem 1} ${top name 2} ${goto 150}${top pid 2} ${goto 200}${top cpu 2} ${goto 250}${top mem 2} ${top name 3} ${goto 150}${top pid 3} ${goto 200}${top cpu 3} ${goto 250}${top mem 3} ${top name 4} ${goto 150}${top pid 4} ${goto 200}${top cpu 4} ${goto 250}${top mem 4} ${color orange}MEMORY / DISK ${hr 2}$color RAM: $memperc% ${membar 6}$color Swap: $swapperc% ${swapbar 6}$color Home: ${fs_free_perc /home}% ${fs_bar 6 /}$color Free Space: ${fs_free /home} ${color orange}NETWORK (${addr eth0}) ${hr 2}$color Down: $color${downspeed eth0} k/s ${alignr}Up: ${upspeed eth0} k/s ${downspeedgraph eth0 25,140 000000 ff0000} ${alignr}${upspeedgraph eth0 25,140 000000 00ff00}$color Total: ${totaldown eth0} ${alignr}Total: ${totalup eth0} ${execi 30 netstat -ept | grep ESTAB | awk '{print $9}' | cut -d: -f1 | sort | uniq -c | sort -nr} ${color orange}WIRELESS (${addr wlan0}) ${hr 2}$color Down: $color${downspeed wlan0} k/s ${alignr}Up: ${upspeed wlan0} k/s ${downspeedgraph wlan0 25,140 000000 ff0000} ${alignr}${upspeedgraph wlan0 25,140 000000 00ff00}$color Total: ${totaldown wlan0} ${alignr}Total: ${totalup wlan0} ${execi 30 netstat -ept | grep ESTAB | awk '{print $9}' | cut -d: -f1 | sort | uniq -c | sort -nr} Conky solutions have been offered, but perhaps these aren't the best way of approaching it. What I really want is to stop icons even appearing in that part of the desktop window: that is, I want to make part of the desktop real estate "off-limits" to new icons appearing on the desktop.

  Read the article

• Can I let maximized windows reach behind the gnome-panel?

  - by Bruce Connor

  My top gnome-panel is set to not expand and sits on the top-right of my screen. I just realized I wouldn't mind if maximized windows were able to get behind it (it wouldn't actually cover up anything). Is it possible to achieve that with the gnome-panel? Here's what it looks like now: Ideally, the window's titlebar would be behind the panel (partially obscured by it). I know that different dock softwares like AWN are able to do that, but I'm running a weak netbook, and I would rather do that with the gnome-panel.

  Read the article

• Is a disk/ata timeout exception dangerous?

  - by j-g-faustus

  I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

  Read the article

• Network Manager Applet menu freezes and does not respond

  - by pst007x

  Since the latest update in Ubuntu 10.10, the nm-applet has started doing some strange things. I boot up the PC, all is fine, internet works, etc... but after a period of time, approx and hour, the nm-applet menu in the Gnome panel fails to respond. when I click on the icon, the menu appears, all looks well, but when I select any option, eg DISCONNECT, nothing happens. Even the VPN sub menu disappears (no triangle to select the menu.) However I do not lose the network connection... If I Run this script: killall nm-applet /etc/init.d/NetworkManager restart nm-applet all returns as normal, for a while... weird? i tried uninstall/reinstall... I even reinstalled Ubuntu, but once the latest updates are applied this issues arises... Any help?

  Read the article

• Fix 403 errors in Google Webmaster Tools

  - by Justin

  Hi Team, I have a domain that has "fallen off a cliff" for searches in Google. Searches that used to be in position 1-4 are now gone from page 1. The same search in Bing shows the typical position expected (top 5 results). In reviewing Google Webmaster Tools, I am seeing two problems: 1. The Sitemap is reporting two errors: General HTTP error: HTTP 403 error (Forbidden) URLs not accessible However, the URL they provide as "no accessible" is accessible. I can click the link Google provides and it works fine. There are 6,000 crawl errors of type 403. Again, most of these pages that have 403 are accessible in my browser (tried various browsers as well). About half are from January, the other half from November. There are no IP-specific firewall rules on ports 80 and 443 that could block the goolgebot Using the user agent switcher add-on for FF I confirmed that the page loads when the user agent is the googlebot I an confirm that most of the pages reported as 403 are accessible. A search of just "site:thedomain.com" does confirm there are over 9,000 in the index. But most searches don't return the site. I believe the 403 issues are the cause of the fall in search rankings, but I can't seem to find any information online with ideas about how to address this. Any ideas? jpe

  Read the article

• Semantic Form Markup for Yes or No Questions - Or Should I Tell my Designers to Bugger Off?

  - by sholsinger

  I frequently receive mock-ups of HTML forms with the following prototype: Some long winded yes or no question?   (o) Yes   ( ) No The (o) and ( ) in this prototype represent radio buttons. My personal view is that if the question has only a true or false value then it should be a check box. That said, I have seen this sort of "layout" from almost every designer I've ever worked with. If I were not to question their decision, or question the client's decision, I'd probably mark it up like this: <p class="pseudo_label">Some long winded yes or no question?</p> <input type="radio" name="the_question" id="the_question_yes" value="1"> <label for="the_question_yes" class="after_radio">Yes</label> <input type="radio" name="the_question" id="the_question_no" value="0"> <label for="the_question_no" class="after_radio">No</label> I really don't want to do that. I want to push back and convince them that this should really be a check box and not two radio buttons. But my question is, if I can't convince them – you're welcome to help me try – how should I code that original design requirement such that it is semantic and at least understandable for screen reader users? If I were able to convince my tormentors to change their minds, I would likely code it in the following fashion: <label for="the_question">Some long winded yes or no question?</label> <input type="checkbox" name="the_question" id="the_question" value="1"> What do you think about this issue? Should I push back? Possibly more importantly is either way semantically correct?

  Read the article

• 'Development dashboard' web application

  - by espais

  Hi all, I am not sure if something like this exists in that it is ready out of the box. I currently have some web space that I use for various projects, and I would like to setup an area for some friends and I to develop web applications together. My ideal setup would be to create a folder, say, webdev.domain.com. We could all go to this domain, login, and then be able to setup new applications, pick which language will be used, setup database tables, allow HTML based file uploading, and create sub-folders to basically have a test bed for the applications. In retrospect, it seems like I'm describing a limited version of cpanel. I could come up with something in Drupal I'm sure, but I don't want to have to really spend time configuring much. Like I said, I want to install it and have minimal configuration. Does something like this exist (preferably in open-source)?

  Read the article

• How do you set up the directory structure for a multilingual site without duplicating content?

  - by Ricardo

  I want to make a website in two languages. I've looked around and settled on the directory option of separating both languages. How do I make it work? Let's say I have the following three files for the landing homepage, the English page and the Spanish page: http://www.domain.com/index.html http://www.domain.com/en/index.html http://www.domain.com/es/index.html Let's also say that /index.html will be in English, with a link to /es/index.html. In turn, /es/index.html will have a link to the English version. Would this be back to /index.html or to /en/index.html. How do I get both English versions (the one at the root and the one in the directory) to actually be the same file in the same directory? I'm new to this, so I'm not using any scripts yet. To me, the obvious solution is to duplicate both English versions and have the one at the root point to files under the /en/ directory, but I'm not a fan of duplication and I've learned that search engines really frown upon that. Anyone point me in the right direction?

  Read the article

• HTML5 Semantics - H1 or H2 for ARTICLE titles in a SECTION

  - by Matt

  It's my understanding (based from this chapter of Dive into HTML5: http://goo.gl/9zliD) that it can be considered semantically appropriate to use H1 tags in multiple areas of the page, as a method of setting the most important title for that particular content. If I'm using this methodology, and I have a SECTION which I've assigned an H1 of 'Articles', should I use H1 or H2 to define the titles for ARTICLEs in that SECTION? This is a bit confusing to me as the article titles are the most important heading for their ARTICLE, but are also 'children' of the SECTION's title. Example code: <section class="article-list"> <header> <h1>Articles</h1> </header> <article> <header> <h2>Article Title</h2> <time datetime="201-02-01">Today</time> </header> <p>Article text...</p> </article> <article> <header> <h2>Article Title</h2> <time datetime="2011-01-31">Yesterday</time> </header> <p>Article text...</p> </article> <article> <header> <h2>Article Title</h2> <time datetime="2011-01-30">The Day Before Yesterday</time> </header> <p>Article text...</p> </article> </section>

  Read the article

• How can I get started installing Buddycloud software to a hosted site?

  - by rujic

  I'm confused about how one hosts a Buddycloud (federated social networking software) channel. I downloaded the source code, but I'm not sure how to install it on my website. Most of the information seems to assume that the host is running their own server, but I have plain ol' paid web hosting. I know that you also need to set up an XMPP server to run Buddycloud, and I'm not sure how to do that on my hosted website—or if it's even possible. If it matters, my site is hosted on a Linux server through IX Web Hosting. I'd greatly appreciate it if you guys could point me in the right direction.

  Read the article

• Website hosted at home pingable from outside, but not browseable from outside [closed]

  - by Richard DesLonde

  I have a simple setup. Server at home has local I.P. 192.168.1.3 IIS is running on the server and the website is up. Windows firewall on the server has an exception rule for port 80 TCP Router has static I.P. XX.XXX.XX.XXX Router is forwarding TCP port 80 to 192.168.1.3 My domain registrar is my DNS host and is pointing to the static I.P. XX.XXX.XX.XXX of the router Here's what I can and can't do. I can browse the website from within my home network either by I.P. or domain name. I can ping the domain and the I.P. from outside the network (from a computer at work). I can't browse the website either by domain name or by I.P. Wierd. Why I can't browse my website?

  Read the article

• Is there a better way to have a two column website with header and footer, equal height columns and stretchy column widths? [closed]

  - by Seamus

  I wrote a website a while ago that is a little messy in how it does things. I used this CSS template and this equal height columns trick. I have not one but two container divs and I can't remember what they're doing. So I'm thinking of re structuring the thing from scratch, and possibly making use of the more "semantic" html5 tags like <nav> and so on at the same time. The question is: is there a better way to achieve a site structure with these properties: 2 equal height main columns (with widths as percentages of the available real estate, not explicitly stated) both a header and footer element that stretch the whole width of the total of the two main columns That allows the use of semantic html5 tags instead of meaningless divs

  Read the article

• How to move a website and domain name without experiencing downtime for emails or site?

  - by user4842

  Okay, I have a pretty complex problem, so I'll get right to it. I'm a designer who built a new website for my client. Their old site is hosted at GoDaddy, as well as their email. Problem is, the guy who built the original site decided to put the original domain name and hosting under HIS personal GoDaddy account. Well, that turned out to be a bad move for several reasons. Here's how it's all tied together. The original domain name, www.domainoriginal.com, was actually purchased at Network Solutions. The original web designer pointed the nameservers from Network Solutions to his GoDaddy account, where the email and hosting is setup. The new domain name, www.domainnew.com, was purchased under a new and separate GoDaddy account belonging to the company, and the new website was built under a 3rd party platform (Big Commerce). So, the www.domainnew.com is already pointed to the new website using A records at new GoDaddy account. All is fine there. However, they still need www.domainoriginal.com to point to the NEW website as well. (The old one can simply be deleted, it is NOT important). AND, they want to keep their old email addresses intact and working as well, but under the NEW GoDaddy account. Obviously, I have no DNS control at Network Solutions, and I have no idea what kind of control I have at GoDaddy under the old account because the web designer will not let me see inside his account. But, he and GoDaddy both tell me nothing can be done other than to repoint the nameservers to Network Solutions, and then repoint the A record to my new website, www.domainnew.com, and point the MX Records to GoDaddy. I'm told the downtime would be 24-48 hours if I do this. Ideally, we'd like to do a domain name transfer and get www.domainoriginal.com in the new GoDaddy account created by the company. But, I'm told this could take up to 7 days. Does this mean the site and email will be down for 7 days? And any emails sent during this time, would they be lost forever? If I do this, how long could I expect the site and email to go down? And, will the emails be permanently lost? I've gotten different answers from everybody at GoDaddy so I kind of don't trust them anymore... Any help would be greatly appreciated Thanks, Tyson

  Read the article

• Strange named anchor behavior - only working with the hash mark after a trailing slash

  - by tnorthcutt

  I have an odd problem. Links to named anchors on a site I'm working on are only working correctly if the pound/hash sign is placed after a trailing slash (e.g. example.com/about/#who), rather than directly after a page name (e.g. example.com/about#who). What could be causing this? I should note that this is on a site running WordPress, with the WPML translation plugin. I'm not sure if that's causing the problem, though (otherwise I'd ask on the WordPress Answers SE site). Any suggestions as to what could be causing this strange behavior?

  Read the article

• IDirect3DDevice9Ex and D3DPOOL_MANAGED?

  - by bluescrn

  So I wanted to switch to IDirect3DDevice9Ex, purely for the SetFrameLatency function, as fullscreen vsynced D3D seemed to produce noticable input lag. But then it tells me 'ha ha ha! now you can't use D3DPOOL_MANAGED!': Direct3D9: (ERROR) :D3DPOOL_MANAGED is not valid with IDirect3DDevice9Ex Is this really as unpleasant as it looks (when you're relying quite heavily on managed resources) - or is there a simple solution? If it really does mean manual management of everything (reloading all static textures, VBs, and IBs on a device reset), is it worth the hassle, will IDirect3DDevice9Ex bring enough benefit to make it worth writing a new resource manager? Starting to think I must be doing something wrong, due to this: Direct3D9: (ERROR) :Lock is not supported for textures allocated with POOL_DEFAULT unless they are marked D3DUSAGE_DYNAMIC. So if I put my (static) textures in POOL_DEFAULT, they need flagging as D3DUSAGE_DYNAMIC, just because I lock them once to load the data in?

  Read the article

• Shadow Mapping and Transparent Quads

  - by CiscoIPPhone

  Shadow mapping uses the depth buffer to calculate where shadows should be drawn. My problem is that I'd like some semi transparent textured quads to cast shadows - for example billboarded trees. As the depth value will be set across all of the quad and not just the visible parts it will cast a quad shadow, which is not what I want. How can I make my transparent quads cast correct shadows using shadow mapping?

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >