Daily Archives

Articles indexed Tuesday June 19 2012

Page 14/18 | < Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >

• Remote additional domain controllers

  - by user125248

  Is it possible to setup several additional domain controllers (ADC) at remote locations that are connected via medium bandwidth DSL (2-10 Mbit) WAN connections for a single domain (intranet.example.com)? And would it be a good idea? We have five sites and would like to have extremely high availability if any of the site were to lose their Internet connection. However each site is very small, and all are over a fairly small geographical area within the same region, so it would seem strange to have a PDC for each of the sites. If it were possible to have an ADC for each site, would the clients use the ADC or just use the PDC if it's available to them?

  Read the article

• Apollo linux boot into single user

  - by Spirit

  We have a device that runs Appolo Linux and I have to boot that device into a single user mode so that i can run a fsck to check the hard drive for errors. I've been goggling this during the past hour and so far I haven't found any specific method on how can I do that on this version on Linux. The device is known formerly as a NFX Cinxi One - now re-branded into BlackStratus LOG Storm. If any of you have any experience with this one you may know it is a device that is used to collect logs from other servers. I know that the above info isn't much but that is everything that I can provide up until now since tomorrow I have to follow up closely on this problem.

  Read the article

• Windows updates behind a physical firewall with only IP based rules and generic outbound connections are turned off

  - by user125245

  I have some boxes that I do not want to allow any in or outbound traffic to the internet Except for windows updates. However the fire wall in place (Cisco ASA) apparently only supports ip based rules. As best I can tell access to Microsoft updates via anything other then the half dozen URL masks the Microsoft lists as needed does not appear possible. I have kicked around building a full WSUS that I would then manually copy the update files to so that no direct Microsoft access is needed but this sounds very top heavy for the very few boxes involved. I have also kicked around manual updates all around but am not certain how to be conveniently and confidently sure that the correct updates are being applied in the correct order. Any ideas from any direction would be appreciated. I want this as simple / cost effective as possible but have very little flexibility on the only absolutely required internet access policy.

  Read the article

• Nginx + Apache + Wordpress redirects to localhost/127.0.0.1

  - by jcrcj

  Anyone know how to fix an issue with Nginx + Apache + Wordpress redirecting to localhost/127.0.0.1? I've tried a lot of different fixes, but none have worked for me. I can go to http://domain.com/wp-admin just fine and use everything there normally. But if I try to go to http://domain.com it redirects to 127.0.0.1. Everything also works fine if I just run through Apache. Here are the relevant portions of my nginx.conf: server { listen 80; server_name domain.com; root /var/www/html/wordpress; location / { try_files $uri $uri/ /index.php; } location ~ \.php$ { proxy_pass http://127.0.0.1:8080; } } Here are the relevant portions of my httpd.conf: Listen *:8080 ServerName <ip> <VirtualHost *:8080> ServerAdmin test@test DocumentRoot /var/www/html/wordpress ServerName domain.com </VirtualHost> This is what my nginx log loks like: <ip> - - [19/Jun/2012:22:35:35 +0400] "GET / HTTP/1.1" 301 0 "-" "Mozilla/5.0 This is what my httpd log looks like: 127.0.0.1 - - [19/Jun/2012:22:24:46 +0400] "GET /index.php HTTP/1.0" 301 - "-" -- WordPress Address (URL) and Site Address (URL) both have same http://domain.com

  Read the article

• How to repair unbootable Fedora install

  - by Cerin

  How do you repair/reinstall Fedora without deleting any existing partitions or data? I was attempting to upgrade some old Fedora 13 servers to 17, following the instructions in the wiki. After the 14-15 upgrade, rebooting resulted in the output: Dropping to debug shell. sh: can't access tty; job control turned off dracut:/# Running dmesg also shows: dracut Warning: No root device "block:/dev/mapper/VolGroup-lv_root" found Googling shows this error is typically related to some weird RAID issues, but my server is a virtual machine not using any RAID. Using a rescue CD, I can chroot /mnt/sysimage, and all packages and data still seems to be there. How do I make the system bootable again?

  Read the article

• Static IPv6 address advertising and IPv6 autoconfig in Debian/Ubuntu

  - by Pascal

  I have a network that advertises IPv6 addresses through IPv6 autoconfig. To allow DNS lookups and to have fancy IP addresses, we setup "static" IPv6 addresses through /etc/network/interfaces: auto eth0 iface eth0 inet dhcp iface eth0 inet6 static address a:b:c:d:e::f netmask 64 Whenever we now connect through IPv6 Linux uses the IPv6 autoconfig address: a:b:c:d:21d:60ff:fe4a:479 and not the static IPv6 address: a:b:c:d:e::f A server on the other side only sees the autoconfig address. Is there a way to force linux (Debian/Ubuntu) to use the static address for outgoing packets? This is especially interesting for reverse DNS and firewall settings. I don't want to disable the IPv6 autoconfig since I don't have control over the settings the router advertises.

  Read the article

• Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

  - by Quanano

  We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

  Read the article

• What are the ways to build a failover cluster?

  - by light

  I have a task where I need to build a failover cluster in two cases: first with servers on Red Hat Enterprise 5.1 and second with SUSE Linux Enterprise 11 SP1. Both cases have SAN. I know there are many ways to build failover cluster, but I can’t find out more, so I need next: The ways to build it? I know only virtualization. Any good book or resource to broad my mind? I’ll be glad to hear any suggestion. Thanks! EDIT #1: failover of servers with bussiness application on it. EDIT #2: will be great to hear summary about solutions with SLES servers? EDIT #3: So if I understand correctly, in my cases the main ways are to use internal solutions or virtualization. So now I have additional questions: Does manufacturer of blades provide some solution? For example HP or IBM. (Without virtualization) Do I need additional server to control "heartbeat" between main and redundant servers? (Virtualization) For example I have several physical servers with VMs. Do I need additional server to control availability of VMs and to move VMs to another physical server in the case their physical server failure? Sorry for my poor English. EDIT #4: Failover of VM or OS on physical server. In both cases will be used SAN , it's not specified, but I think with file system image on it. I started to think that my question is stupid and I need to remake it.

  Read the article

• Hotmail Senders receiving NDR : "550-Please turn on SMTP Authentication in your mail client..."

  - by DKNUCKLES

  Recently, senders from Hotmail have begun to get the following NDR when trying to e-mail our domain. EDIT : Full NDR Message Action: failed Status: 5.5.0 Diagnostic-Code: smtp;550-Please turn on SMTP Authentication in your mail client, or login to the 550-IMAP/POP3 server before sending your message. 550-snt0-omc3-s36.snt0.hotmail.com [65.55.90.175]:49271 is not permitted to 550 relay through this server without authentication This is seemingly out of the blue and I'm at a loss as to why this is happening. Pertinent Information We have multiple domains hooked up to our Exchange server. We changed our company name in January of this year, and the old primary domain (olddomain.com) will accept e-mails from Hotmail accounts, however e-mails sent to the new primary domain (newdomain.com) bounce back with the NDR listed above. The bounces only appear to be happening when the Hotmail sender is sending a new e-mail, and not if they are responding to an e-mail sent from our end. We have made no changes to the configuration of our server recently. This e-mail first appeared last Friday. As far as I can tell, the mail doesn't even seem to get to our server We performed an Exchange 2003 to 2010 migration last year. The 2003 acts as a Smart Host Any advice on this issue would be greatly appreciated! I'm at a loss

  Read the article

• Why my Ldirectord check multiple times on read server every interval?

  - by garconcn

  I have a Ldirectord server and two real servers. My ldirectord used to check the request page on real server once in every interval, but now I found that it check four times. I have monitored the log on both real servers, they have the same problem. Here is my ldirectord configuration: checktimeout=10 checkinterval=5 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=no virtual=192.168.1.100:80 fallback=127.0.0.1:80 real=192.168.1.10:80 gate real=192.168.1.20:80 gate service=http request="lb.html" receive="still alive" scheduler=sh persistent=60 protocol=tcp checktype=negotiate Ldirectord will connect to each real server once every 5 seconds (checkinterval) and request 192.168.0.10:80/test.html (real/request). The access log in real server: 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805"

  Read the article

• Connecting two servers together - How to?

  - by Chris

  Is it possible to connect two servers running for example Windows Server 2003/2008 together. For example they are seen on the network as one server with the combination of all HDD from each server? Example: \\Server1 - 1 x 1tb hdd \\Server2 - 1 x 1tb hdd I would like users of the network to be able to store their documents on both servers for load balancing. So basically a RAID between the two servers? Any help would be appreciated.

  Read the article

• RRAS won’t start with 8007042a or event ID 7024, aka the “routing remote access unable to load Iprtrmgr.dll”

  - by KCotreau

  History: The history of this error, which has mostly gone unsolved, dates back to Windows 2000. Platforms affected: Windows Server 2008 R2, Server 2008, Server 2003 R2, Server 2003, Server 2000 (both 32-bit and 64-bit installs are affected). Error Messages Event ID: 7024 The Routing and Remote Access service terminated with service-specific error 2 (0x2). Event ID: 7024 The Routing and Remote Access service terminated with service-specific error 31 (0x1F). Event ID: 7024 The Routing and Remote Access service terminated with service-specific error 20205 (0x4EED). Event ID: 7024 The Routing and Remote Access service terminated with service-specific error 193 (0xC1). Event ID: 20103 Unable to load C:\WINDOWS\System32\iprtrmgr.dll . (32-bit installs). Event ID: 20103 Unable to load C:\WINDOWS\SysWOW64\iprtrmgr.dll . (64-bit installs).

  Read the article

• Out of nowhere, ssh_exchange_identification: Connection closed by remote host

  - by disusered

  I am running Ubuntu 10.10 on a remote box. I ssh to it everyday without issues but today out of the blue, I get the following error: ssh_exchange_identification: Connection closed by remote host If I connect with -vv, I get the following: OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /Users/bla/.ssh/config debug1: Applying options for ubuntu-server debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ubuntu-server.com [123.123.123.123] port 22. debug1: Connection established. debug2: key_type_from_name: unknown key type '-----BEGIN' debug2: key_type_from_name: unknown key type '-----END' debug1: identity file /Users/bla/.ssh/id_rsa type -1 debug1: identity file /Users/bla/.ssh/id_rsa-cert type -1 ssh_exchange_identification: Connection closed by remote host If I remove the key, I get the exact same output (sans "debug2: key_type_...). I've managed to log in physically and checked my hosts.allow and hosts.deny but they have no entries. I tried removing and reinstalling OpenSSH, checked authorized_keys and ~/.ssh permissions and tried connecting from other computers only to get the same error. I'm at my wits end, any help would be greatly appreciated.

  Read the article

• How to escape or remove double quotes in rsyslog template

  - by Evgeny

  I want rsyslog to write log messages in JSON format, which requires to use double-quotes (") around strings. Problem is that values sometime include double-quotes themselves, and those need to be escaped - but I can't figure out how to do that. Currently my rsyslog.conf contains this format that I use (a bit simplified): $template JsonFormat,"{\"msg\":\"%msg%\",\"app-name\":\"%app-name%\"}\n",sql But when a msg arrives that contains double quotes, the JSON is broken, example: user pid=21214 uid=0 auid=4294967295 msg='PAM setcred: user="oracle" exe="/bin/su" (hostname=?, addr=?, terminal=? result=Success)' turns into: {"msg":"user pid=21214 uid=0 auid=4294967295 msg='PAM setcred: user="oracle" exe="/bin/su" (hostname=?, addr=?, terminal=? result=Success)'","app-name":"user"} but what I need it to become is: {"msg":"user pid=21214 uid=0 auid=4294967295 msg='PAM setcred: user=\"oracle\" exe=\"/bin/su\" (hostname=?, addr=?, terminal=? result=Success)'","app-name":"user"}

  Read the article

• Compression for custom mime type works on IIS 7.5, but not IIS 7.0?

  - by Doogal

  I've managed to set up compression for a custom mime type on IIS 7.5 with no problem. Add the mime type to IIS then add it to the httpCompression element in applicationHost.config. But when I do the same thing on IIS 7, the particular mime type is never compressed. This isn't a problem with compression in general since other mime types are compressed correctly. As far as I can tell, IIS 7 and IIS7.5 are configured in exactly the same way. Does IIS7 behave differently and do I need to do something else to get it working? I've setup failed request tracing and get a NO_MATCHING_CONTENT_TYPE error during compression but I can't figure out what else I need to do to tell IIS about my mime type

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  **IGNORE THIS QUESTION - SOLVED WITH A PYTHON SCRIPT available at: http://yabahaus.blogspot.com I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• Folder redirection GPO doesn't seem to be working

  - by user57999

  I've been trying to set up roaming profiles and folder redirection, but have hit a bit of a snag with the latter. This is exactly what I've done so far: (I have OU permissions and GPO permissions over my division's OU.) Created a group called Roaming-Users in the OU 'Groups' Added a single user (testuser) to the group Using the Group Policy Management tool (via RSAT on Windows 7) I right-clicked on the Groups OU and selected 'Create a GPO in this domain, and Link it here' Added my 'Roaming-Users' group to the Security Filtering section of the policy. Added the Folder Redirection option, specifically for Documents. It is set to redirect to: \myserver\Homes$\%USERNAME%\Documents (Homes$ exists and is sharing-enabled). Right-clicked on the policy under the Groups OU and checked Enforced. Logged into a machine as testuser successfully. Created a simple text file, saved some gibberish, logged off. Remoted into the server with Homes$ on it, noticed that the directory Homes$\testuser was created, but was empty. No text file to be found. From what I've read, I did everything I aught to...but I can't quite figure out the issue. I had no errors when I logged off about syncing issues (offline files is enabled) or anything, so I can only imagine my file should have ended up up on the share. Any ideas? EDIT: Using gpresult /R, I confirmed the user is in fact part of the Roaming-Users group, but does not have the policy applied, if that helps. EDIT 2: Apparently you can't apply GPOs to groups...so I applied to users and used the same security filter to limit it to my test user. Nothing happens as far as redirection goes, but I now have the following error in the event log: Folder redirection policy application has been delayed until the next logon because the group policy logon optimization is in effect

  Read the article

• Sync files between two users on Windows-7 Enterprise

  - by Zachary

  I'm running Windows-7 enterprise on a dell Laptop, and I'd like to sync the entire user directory structure between two users. Background: I am an existing user on the computer, and soon I'll be sharing the computer with an employee. I want everything from my account to overwrite the other, while anything he does is mirrored on mine. I'm not worried about security because nothing vital is on the computer. Both accounts are administrators, and I have already tried to use hard links to accomplish this. However the prompt leaves me with "Access Denied". Is what I'm trying to do possible, and if so what steps must be done to accomplish it?

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• How can I force Parallels' networking to obtain an IP through a wireless router?

  - by RLH

  Here is my setup. I have a Macbook, Thunderbolt display and an Ethernet connection plugged into the Thunderbolt display. During the day, most of my network use can (and should) operate across the ethernet associated with my display. However, I also need to be able to connect up to a wireless router. This hasn't been a problem on the Mac OS X side, but the program that I need to run on the router has to obtain an IP address from the wireless access point. Considering my current setup, how can I leave it so that I can access the internet in OS X, yet have my Window 7 instance running in Parallels, get it's assigned IP address from a wireless router that my Mac is also connected to? I've fiddled around with the Parallel's network settings for an hour, and I can't get Parallel's to see the router, even though my Mac is certainly connected to it.

  Read the article

• Installing Trac on Windows under Apache 2.2?

  - by Warren P

  Trac is a python-powered bug-tracking and project-management app. According to Trac's wiki, there are several options for installing Trac, a standalone server (tracd), or under a dedicated webserver using one of these options: FastCGI - Not available on windows. mod_wsgi - No version of mod_wsgi available for Apache 2.2.22 and Python 2.7.3-amd64 that actually runs on my system! mod_python - no longer recommended, as mod_python is not actively maintained anymore) CGI -should not be used, as the performance is far from optimal) That leaves me with zero ways to run Trac on Windows. Apache 2.2.22 with ModWSGI loading, crashes the Apache2.2 service on startup without any error logs. Disabling the line in the apache configuration to load mod_wsgi restores sanity. I just want an installation of Trac on windows with Authentication enabled. I am unable to get authenetication to work using basic tracd like this: tracd -p 8000 --basic-auth="c:\tmp,c:\tmp\Passwords.md5.txt,mycompany" c:\tmp\RootFolder And I am unable to get Mod_WSGI installed. I'm going to keep trying to figure out a combination that works, I suspect I should have installed 32 bit python instead of 64 bit python, to start with. Did I do wrong to install Python 64 bit 2.7.3? I tried again with all 32 bit components, and still can't get MOD_WSGI to work with apache 2.2.22. I'm going to try to compile mod_wsgi myself with Visual C++ Express 2010, but it seems to me that it ought to be easier than this to get Trac running on windows, with authentication. Is there a way to run Trac on Windows, under Apache, with authentication? The last "Trac on windows" article died in 2008, leaving only this internet archive link for "Trac on windows" setup.

  Read the article

• Live Screencast under Linux

  - by OmnipotentEntity

  I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

  Read the article

• Multiple Settings for One Monitor

  - by Lynda

  I have my monitor set to the way I like it, it shows colors accurately and not overly bright (white doesn't blind me). However I edit photos for the web and this is great for my screen but I have noticed when looking at other screens my photos will at times looked washed out and not a good presentation. If I manually change my monitor settings to be brighter (and a few other tweaks) I can replicate the look of other monitors close enough to help prevent washed out/blown out photos. Here is the issue, I need to be able to change settings between the two fairly easily. To manually set my monitor for one then back to the other can be time consuming and a pain to set right every time. I would like to be able to preset certain settings (in software) that I can quickly switch between by pressing hotkeys or clicking shortcut on my desktop. I have an AMD video card and have attempted to use the AMD VISION Engine Control Center to add presets then tweak the settings for each. However when I switch between the presets the settings are the same. How do I build presets using the VISION Engine Control Center that actually works (maybe I misunderstand what it is saving?) or is there a way to do this in Windows 7 or free software that actually works decently for this purpose?

  Read the article

• How to recreate Windows Live Mail filter rules in Thunderbird?

  - by FernandoSBS

  I have some filters in Windows Live Mail that I'm trying to port to thunderbird without success. It seems Thunderbird filter is very limited. Here is an ex of a filter i'm trying to recreate: Apply this rule after the message arrives Where the From line contains '[email protected]' or '[email protected]' or 'Programa TAM Fidelidade' and Where the message body contains 'esteja visualizando' and 'por ser cadastrado no Programa TAM Fidelidade' Move it to the Deleted items folder and Stop processing more rules In Thunderbird I can´t combine a list of "or"s with some "and"s, because it only allows you to select "message matches ALL of the criteria below" or "ANY of the below". Am I missing something or it really is very limited?

  Read the article

• Search Replace extended in a html file

  - by Fake4d

  i have a little question. I have a big html file and want to replace lots of things inside a lot of times. The only problem i cant solve is a replace with a variable. Example: <image src="start_files\0002.jpg" style="width:216pt; height:162"> should be transformed in <a href="start_files\0002.jpg" target="_blank"><image src="start_files\0002.jpg" style="width:216pt; height:162"></a> do you have an idea how to do it? I have a windows system with Notepad2 and Notepad++ and i could install a new tool if needed. (like Windows SED). The best solution would be a batch solution where i can add other transformations. Hope you have got good ideas! Thanks forward, Fake4d

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18  | Next Page >