Daily Archives

Articles indexed Thursday October 18 2012

Page 14/17 | < Previous Page | 10 11 12 13 14 15 16 17  | Next Page >

• Citrix Xen VM's lose networking

  - by Ash

  My client has a XenServer 6.0.2 installation with 2 Window Server 2008 R2 virtual machines. Whenever the virtual machines are rebooted they lose their IP settings (IP address, subnet, gateway). Each time after a reboot I need to login to each VM via XenCenter and re-apply the required static IP settings. This causes issues with connected iSCSI drives within each VM - drives need to be reconnected after each reboot. For example, a network adapter has the following settings pre-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 IPv4 Address. . . . . . . . . . . : 10.101.0.101(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.101.0.10 DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Post-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 Autoconfiguration IPv4 Address. . : 169.254.153.174(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Under XenCenter -- Virtual Network Interfaces, each adapter is set to a static MAC address (i.e. "Use this MAC address"). I have tried the following commands within one VM but this had no effect: netsh winsock reset catalog netsh int ip reset Can someone please help?

  Read the article

• Unable to Mange DNS via MMC

  - by IT Helpdesk Team Manager

  When trying to access the DNS service on Microsoft Windows Server 2003 (Build 3790) domain controller/schema master via the MMC DNS snap in or locally via the DNS MMC from Administrative tools I'm getting a red "X" through the icon for the DNS Server. The inability to access DNS management via MMC happens on all domain controllers as well. We've looked at items such as the DHCP client not being started, incorrect DNS setup ( the machine points at itself and another DC ), the DNS service not running ( it is and all DNS queries via NSLOOKUP work correctly ), dslint returns the correct information and functions as expected. There is the following entry in the DNS event log: The DNS server could not initialize the remote procedure call (RPC) service. If it is not running, start the RPC service or reboot the computer. The event data is the error code. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. 0000: 0000051b dnscmd fails with RPC server unavailable yet RPC is started: C:\Documents and Settings\Administrator.DOMAIN>dnscmd /Info Info query failed status = 1722 (0x000006ba) Command failed: RPC_S_SERVER_UNAVAILABLE 1722 (000006ba) DCDIAG /TEST:DNS /V /E produces the following errors: Warning: no DNS RPC connectivity (error or non Microsoft DNS server is running) [Error details: 1753 (Type: Win32 - Description: There are no more endpoints available from the endpoint mapper.)] Warning: no DNS RPC connectivity (error or non Microsoft DNS server is running) [Error details: 1722 (Type: Win32 - Description: The RPC server is unavailable.)] The DNS server could not initialize the remote procedure call (RPC) service. If it is not running, start the RPC service or reboot the computer. The event data is the error code. A DNS query for _ldap._tcp.dc._msdcs. returns the correct results. All domain and ADS related activities are working except that I can't manage my DNS via MMC or dnscmd. Any thoughts or solutions would be greatly appreciated. EDIT: Adding Registry export per request: Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc Class Name: <NO CLASS> Last Write Time: 10/18/2012 - 2:29 PM Value 0 Name: DCOM Protocols Type: REG_MULTI_SZ Data: ncacn_ip_tcp Value 1 Name: UuidSequenceNumber Type: REG_DWORD Data: 0xb19bd0f Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc\ClientProtocols Class Name: <NO CLASS> Last Write Time: 3/9/2007 - 12:11 PM Value 0 Name: ncacn_np Type: REG_SZ Data: rpcrt4.dll Value 1 Name: ncacn_ip_tcp Type: REG_SZ Data: rpcrt4.dll Value 2 Name: ncadg_ip_udp Type: REG_SZ Data: rpcrt4.dll Value 3 Name: ncacn_http Type: REG_SZ Data: rpcrt4.dll Value 4 Name: ncacn_at_dsp Type: REG_SZ Data: rpcrt4.dll Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc\NameService Class Name: <NO CLASS> Last Write Time: 2/20/2006 - 4:48 PM Value 0 Name: DefaultSyntax Type: REG_SZ Data: 3 Value 1 Name: Endpoint Type: REG_SZ Data: \pipe\locator Value 2 Name: NetworkAddress Type: REG_SZ Data: \\. Value 3 Name: Protocol Type: REG_SZ Data: ncacn_np Value 4 Name: ServerNetworkAddress Type: REG_SZ Data: \\. Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc\NetBios Class Name: <NO CLASS> Last Write Time: 2/20/2006 - 4:48 PM Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc\RpcProxy Class Name: <NO CLASS> Last Write Time: 3/9/2007 - 12:11 PM Value 0 Name: Enabled Type: REG_DWORD Data: 0x1 Value 1 Name: ValidPorts Type: REG_SZ Data: pdc:100-5000 Key Name: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Rpc\SecurityService Class Name: <NO CLASS> Last Write Time: 2/20/2006 - 4:48 PM Value 0 Name: 9 Type: REG_SZ Data: secur32.dll Value 1 Name: 10 Type: REG_SZ Data: secur32.dll Value 2 Name: 14 Type: REG_SZ Data: schannel.dll Value 3 Name: 16 Type: REG_SZ Data: secur32.dll Value 4 Name: 1 Type: REG_SZ Data: secur32.dll Value 5 Name: 18 Type: REG_SZ Data: secur32.dll Value 6 Name: 68 Type: REG_SZ Data: netlogon.dll

  Read the article

• What's faster, cp -R or unpacking tar.gz files?

  - by Buttle Butkus

  I have some tar.gz files that total many gigabytes on a CentOS system. Most of the tar.gz files are actually pretty small, but the ones with images are large. One is 7.7G, another is about 4G, and a couple around 1G. I have unpacked the files once already and now I want a second copy of all those files. I assumed that copying the unpacked files would be faster than re-unpacking them. But I started running cp -R about 10 minutes ago and so far less than 500M is copied. I feel certain that the unpacking process was faster. Am I right? And if so, why? It doesn't seem to make sense that unpacking would be faster than simply duplicating existing structures.

  Read the article

• I can't connect to internet via lan cable because 2032 battery died and my bios bios info is now empty [closed]

  - by Rand Om Guy

  I have a compaq CQ61-112SL from about 5 years now... the main battery is almost dead, doesn't keep more then 10 minutes. anyway my problem is that my motherboard battery didn't have any more energy left a few days ago and since then I can't access internet through lan cable but only via wifi. I need cable though. I saw that on my BIOS setup page there were a bunch of parameters missing like serial number, UUID, product number and stuff like that. Also when I start the notebook it prints something like : No serial found. or something like that. I don't really know if the reason why my lan cable doesn't work is the empty BIOS but i assume that's it. If it's not please enlighten me. Or anyway tell me how to update the serial number and product number to the real ones (instead of the 0000000000000 that is now in my bios). I downloaded HP DMI which should make it possible to set these variables on the BIOS but i'm on Windows 8 64bit and the executable file that I need to open for my laptop model says it can't run on 64 bit.

  Read the article

• libvirt's dnsmasq does not respond to dns queries or provide dhcp

  - by Jeremy

  This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

  Read the article

• SQUID Transparent SSL proxy (no intercept)

  - by user974896

  I know how to have squid work as a transparent proxy. You put it into transparent mode then use your router or IPTABLES to forward port 80 to the squid port. I would like to do the same for SSL. Every guide I see mentions setting up keys on the squid server. I do not want squid to actually decrypt the SSL traffic then establish a connection with the server, rather I would like squid to simply forward the SSL traffic as is. The only thing I would like to do is be able to check the SSL request for any offending IPs and drop the packets if the destination is one of them.

  Read the article

• Apache - Difference between ScriptAlias and WSGIScriptAlias

  - by Jiri Kadlec

  I'm using apache on RHEL Linux server In my /etc/httpd/conf.d/httpd.conf there are two directives: WSGIScriptAlias /apps /var/www/apps <Directory /var/www/apps > Options MultiViews ExecCGI MultiviewsMatch Handlers SetHandler wsgi-script Order allow, deny allow from all </Directory> ScriptAlias /scripts /var/www/scripts <Directory /var/www/scripts > Options MultiViews ExecCGI MultiviewsMatch Handlers SetHandler wsgi-script Order allow, deny allow from all </Directory> What is the difference? I understand that WSGIScriptAlias is restricted for running Python scripts and ScriptAlias also allows running perl scripts. Can I always use ScriptAlias instead of WSGIScriptAlias? Are there any performance advantages of using WSGIScriptAlias instead of ScriptAlias?

  Read the article

• Command-line tool to search for file names on offline backup drives

  - by halloleo

  I am looking for an open-source (command-line) tool to register and search all my (backup) drives on a file name level. I want to search for file and folder names preferably written as regular expressions or file glob patterns. The external drives contain just normal HFS and NTFS filesystems. The backups are done via direct file copy. Requirement is that the tool compiles on OS X and works without each of the drives attached, but rather pointing me to the drive in case a drive contains a file with the pattern I searched for. At the moment I use a hand-knit script solution with locate databases, one for each external backup drive, but this is rather cumbersome, because locate itself can accesses only one database at a time and does not contain any management system for all the indices/databases. Are there any other tools out there for this?

  Read the article

• Squid stale-while-revalidate not working when max-age=0

  - by Wiliam

  Squid 2.7 always reaches backend, expected is to reach backend using stale-while-revalidate only when cache expires, not when client triggers max-age=0. Script: <?php header('Cache-Control: public, max-age=10, stale-if-error=200, stale-while-revalidate=500'); header("Last-Modified: " . gmdate("D, d M Y H:i:s") . " GMT"); sleep(2); die("OK"); And squid config: # http_port public_ip:port accel defaultsite= default hostname, if not provided http_port 80 accel defaultsite=mydomain.com # IP and port of your main application server (or multiple) cache_peer 127.0.0.1 parent 8000 0 no-query allow-miss originserver name=main # Do not tell the world that which squid version we're running httpd_suppress_version_string on # Remove the Caching Control header for upstream servers header_access Cache-Control deny all #header_access Last-Modified deny all # log all incoming traffic in Apache format logformat combined %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %Hs %<st "%{Referer}>h" "%{User-Agent}>h" %Ss:%Sh access_log /usr/local/squid/var/logs/squid.log combined all cache_effective_user squid refresh_pattern . 10080 90% 999999 ignore-no-cache override-expire ignore-private icp_port 0

  Read the article

• Connect to VPN from Mac on Time Capsule network

  - by Lou Franco

  I have a few clients on my network that can connect to my work VPN (Windows PPTP) when they are not on my home network. On my home network (Cable Modem with Time Capsule providing Wifi), it fails very early -- looks like it can't even establish a connection. Logs just say that it failed -- even verbose logs don't have much: I redacted the host and IP from this log, but I can ping it. Wed Feb 2 14:32:41 2011 : PPTP connecting to server 'XXX.XXX.com' (XXX.XX.XX.XX)... Wed Feb 2 14:32:41 2011 : PPTP connection established. Wed Feb 2 14:32:41 2011 : using link 0 Wed Feb 2 14:32:41 2011 : Using interface ppp0 Wed Feb 2 14:32:41 2011 : Connect: ppp0 <--> socket[34:17] Wed Feb 2 14:32:41 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:44 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:47 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:50 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:53 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:56 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:32:59 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:02 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:05 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:08 2011 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x543c7af8> <pcomp> <accomp>] Wed Feb 2 14:33:11 2011 : LCP: timeout sending Config-Requests Wed Feb 2 14:33:11 2011 : Connection terminated. Wed Feb 2 14:33:11 2011 : PPTP disconnecting... Wed Feb 2 14:33:11 2011 : PPTP disconnected Others can get to the VPN and I can too, but not on my network. The only clue I have seen in other forums is to set the NAT default host on the Time Capsule -- I set this to the IP that my mac got over DHCP. I made sure that my Mac gets a different range of IP addresses that it would get if it connected to the VPN (192.168.1.x vs. 10.0.0.x). Not using any VPN client -- just Network System Preferences. It has worked in the past -- but it was a while ago, so I can't pinpoint a change. My sysadmin doesn't even see incoming connections to the VPN (nothing logged about me when I connect). Looking for any diagnostic advice at all

  Read the article

• Package problems after upgrade

  - by Dan

  I installed a new upgrade on ubuntu which seemed to fail near the end. Now I'm being told that an error has occurred and to please run apt-get to see what's wrong. After some further tries with that I eventually gave up. It seems there's a left over latex package(?) somewhere and I can't seem to get rid of or fix it. Here's an example: blank@ubuntu:~$ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: tex-common : Breaks: texlive-common (< 2010) but 2009-15 is installed texlive-base : Depends: texlive-binaries (>= 2012.20120516) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-doc-base : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-extra-utils : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed texlive-font-utils : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-generic-recommended : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-base-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-extra-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-latex-recommended-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-luatex : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pictures-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks : Depends: texlive-binaries (>= 2012-0) but 2009-11ubuntu2 is installed Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed texlive-pstricks-doc : Depends: texlive-common (>= 2012.20120516) but 2009-15 is installed zlib1g : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed zlib1g:i386 : Breaks: texlive-binaries (< 2009-12) but 2009-11ubuntu2 is installed E: Unmet dependencies. Try using -f. I've seen similar errors on the site here, but not close enough that i could get it fixed. Any help would be great, Thanks

  Read the article

• Access boot menu from Windows 8 PC

  - by svnpenn

  I have a computer that came with Windows 8 preinstalled. I want to boot from a CD, in this case Hiren's Boot CD. However Windows 8 doesn't seem to like this. I have tried pressing F8, ESC, F12 and so on. I read online that Windows 8 can boot in 200ms, so that it might not even be possible to boot from a Live CD before Windows loads. I would like to know how to boot from a CD before Windows loads, if possible. If not possible, how to boot from the Live CD after Windows loads.

  Read the article

• reg delete gives me "access is denied" but regedit delete is ok

  - by Radek

  I need to delete a key from a command line. So I wanted to use reg delete "the key to be deleted" /f but I get ERROR: access is denied. From the same login session (the same user) I am able to delete the key without any troubles from regedit.exe that is not run as administrator. I cannot use runas command to execute reg that I believe would be to solution because in fact I want to use reg to delete registry entry for administrator profile so runas works again. More info in my other question Windows7 corrupted profile - prevention exists?

  Read the article

• Microsoft Excel not graphing

  - by SmartLemon

  Im not sure if this is a math question or a su question. The experiment was relating the period of one "bounce" when you hang a weight on a spring and let it bounce. I have this data here, one being mass and one being time. The time is an average of 5 trials, each one being and average of 20 bounces, to minimize human error. t 0.3049s 0.3982s 0.4838s 0.5572s 0.6219s 0.6804s 0.7362s 0.7811s 0.8328s 0.869s The mass is the mass that was used in each trial (they aren't going up in exact differences because each weight has a slight difference, nothing is perfect in the real world) m 50.59g 100.43g 150.25g 200.19g 250.89g 301.16g 351.28g 400.79g 450.43g 499.71g My problem is that I need to find the relationship between them, I know m = (k/4PI^2)*T^2 so I can work out k like that but we need to graph it. I can assume that the relationship is a sqrt relation, not sure on that one. But it appears to be the reverse of a square. Should it be 1/x^2 then? Either way my problem is still present, I have tried 1/x, 1/x^2, sqrt, x^2, none of them produce a straight line. The problem for SU is that when I go to graph the data on Excel I set the y axis data (which is the weights) and then when I go to set the x axis (which is the time) it just replaces the y axis with what I want to be the x axis, this is only happening when I have the sqrt of "m" as the y axis and I try to set the x axis as the time. The problem of math is that, am I even using the right thing? To get a straight line it would need to be x = y^1/2 right? I thought I was doing the right thing, it is what we were told to do. I'm just not getting anything that looks right.

  Read the article

• rsync windows to linux permission denied

  - by user64908

  Using Command rsync -avzP --delete --omit-dir-times ../../ [email protected]:/var/www/mysite/ I'm getting rsync: mkstemp "/var/www/mysite/.." failed: Permission denied (13) If ext is in the www-data group should I still set all the files to be owned by user www-data? I am trying to publish the files with rsync and then set the permissions using sudo chown -R www-data doc sudo chgrp -R www-data doc but I can't even rsync because of the permission denied. The SSH works fine, the rsync too except when it tries to write over or update some of the files in /var/www Client * Windows 7 * Cygwin 1.7.16 (GNU bash, version 4.1.10(4)-release (i686-pc-cygwin)) * rsync version 3.0.9 protocol version 30 Server * Ubuntu 12.04 * Apache2 * Root Accounts [ubuntu,ext] * Groups [www-data] * sudo vigr has www-data:x:33:ubuntu,ext I have already configure this http://stackoverflow.com/questions/2124169/cwrsync-ignores-nontsec-on-windows-7 This article has also managed to confuse me http://unix.stackexchange.com/questions/41687/how-should-i-rsync-files-in-var-www-if-i-want-them-to-be-owned-by-www-data What is the right procedure?

  Read the article

• where is my disk space?

  - by user166241

  I recently had a problem with .xsession-errors file - it became very big ( 90GB) and took all disk space: How I can check what takes disk space in /tmp?. I cleaned it with command > .xsession-errors but after an hour it became large again. So I deleted it (rm .xsession-errors) - it helped because it wasn't recreated but again after hour disk space disappeared - now there is no .xsession-errors anymore but I don't know where is the memory: df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 106640456 101223392 4 100% / udev 8166744 8 8166736 1% /dev tmpfs 3270224 972 3269252 1% /run none 5120 0 5120 0% /run/lock none 8175552 152 8175400 1% /run/shm du -sc * .[^.]* | sort -n 0 initrd.img 0 initrd.img.old 0 proc 0 sys 0 vmlinuz 0 vmlinuz.old 4 cdrom 4 lib64 4 media 4 mnt 4 selinux 8 dev 12 srv 16 lost+found 68 tmp 1124 run 3396 lib32 5164 .rpmdb 5540 root 8888 sbin 9120 bin 17132 etc 106080 opt 116956 boot 861908 lib 3530584 usr 3821836 var 13371260 home 21859112 total So there is around 100GB used but executing du -sc * .[^.]* | sort -n in root directory finds only ~21 GB - so what takes 80GB?? How to check it? I suspect that when I deleted the `.xsession-errors' file the errors were redirected somwhere else - but where?

  Read the article

• Error 0x80073cf9 when installing or updating apps from windows store

  - by cmorse

  On my Windows 8 desktop I keep getting error 0x80073cf9 when I try to install or update an app from the windows store. In the installings apps pane it just says "This app wasn't installed -- view details" and when I select that it says "Something happened and this app couldn't be installed. Please try again. Error code: 0x80073cf9" I am using the built-in windows firewall and antivirus. And my laptop is able to install updates when it is on the same network. This is what winstore.log shows when I try to update the maps app: 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] *********************************************************************** 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Process name: C:\Windows\system32\taskhost.exe 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] User name: Desktop\User 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Computer name: desktop 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Windows build: 9200.16424.amd64fre.win8_gdr.120926-1855 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011628] Client version: 615 2012-10-18 15:31:47.328, _Info_ WS [00015160:00011428] CWSTileUpdateHandler::Worker: Broker is handling badge updates. 2012-10-18 15:31:47.554, _Info_ WS [00002572:00008200] CProgressDispatcher::OnProgress: AppId = 97a2179c-38be-45a3-933e-0d2dbf14a142, PFN = Microsoft.BingMaps_8wekyb3d8bbwe, InstallPhase = 1, PhasePercent = 0, TotalPercent = 0 2012-10-18 15:31:47.558, _Warning_ WS [00002572:00008200] CDownloadProgress::IDownloadCompletedCallback::Invoke: Download complete result 0x80073cf9 for Microsoft.BingMaps_8wekyb3d8bbwe 2012-10-18 15:31:47.559, _Error_ WS [00002572:00008200] CActionItem::_DoDownload: Download failed for 97a2179c-38be-45a3-933e-0d2dbf14a142, hr=0x80073cf9 2012-10-18 15:31:47.560, _Info_ WS [00002572:00008200] CActionItem::_DoDownload: Notifying progress handlers of download failure for 97a2179c-38be-45a3-933e-0d2dbf14a142, hr=0x80073cf9 2012-10-18 15:31:47.560, _Error_ WS [00002572:00008200] CProgressDispatcher::OnError: PFN = Microsoft.BingMaps_8wekyb3d8bbwe, InstallPhase = 1, hrError = 0x80073cf9

  Read the article

• I just deleted my backup file! How do I save it?

  - by Sammy

  I just accidentally deleted a backup file that I need to restore my system. It's an Acronis True Image TIB file. It was stored at H:\My backups and the name of the file was File_backup_2012-10-18.tib. I did a quick scan with Recuva 1.43.623 and it found the file using the recovery wizard, but it was unable to recover it. The "state" of the file is "unrecoverable". So the resulting file is 0 byte. I am trying to do a deep scan with Recuva right now but it takes a lot of time. If it should fail, what other recovery option do I have? Is there any other good file recovery software that's free to use for home users? I do have a second copy of the whole system partition, but I needed this file backup copy because it is more up to date. That's the file, right there! But why is Recuva unable to recover it?

  Read the article

• How could I make a bash script to execute apt-get?

  - by poz2k4444

  I'm trying to automatize some configurations I have with bash script, I've never done this before so I tried with something easy like a Hello World! and everything works just fine, but then I tried something like this: #!/bin/bash sudo su apt-get purge postfix and it doesn't do anything, I check and postfix is still installed, and at any time it asks for any entry of mine, I just tried with apt-get but I'll do things like ssh-keygen or even write files I guess with cat or something, how could I do the script working and also seeing what's going on?

  Read the article

• Why is it possible to change the password of an admin user on linux?

  - by enum

  A few days ago, a friend of mine, wanted to show me that he can use my linux even if I don't tell him my password. He entered in GRUB, selected the recovery mode option. My first problem is that he already had access to my files (read only). He tried to do passwd but failed. Then he did some kind of remount (I guess that gave him write rights) and after that he was able to change my password. Why is this possible? I personally see it a security issue. Where I work there are several people that use linux and neither of them have a BIOS password set or some other kind of security wall.

  Read the article

• Windows API Error 2 when installing MikTex (Win7)

  - by GreenAsJade

  I am trying to install MikTex 2.9.3927 on Windows 7 x64. Very early in the installation process, I get a MikTex setup wizard error saying: "Windows API Error 2: The system cannot find the file specified Details: C:...\somefile.tpm" The file that results in the error seems to be different every time I try. I have tried many different installation paths, with many different setup options. The same error occurs if I download the ~138MB "Basic MiKTeX 2.9" Installer or if I use the Net Installer to download the entire setup (~1GB). Note that this is a duplicate question - the other copy of this question is closed to users of under 10 rep. I have asked it so that I can provide an updated answer...

  Read the article

• Windows7 corrupted profile - prevention exists?

  - by Radek

  I have dedicated Windows7 (not on domain) virtual machine for overnight automation testing. Some commands (mySQLdump, tscon.exe) must be run under administrator account. Last week administrator account's profile was corrupted. I fixed it by renaming it in the registry and logging in as administrator. And today it is corrupted again. I use administrator account only to run above commands via runas. Also the computer is restarted via cmd - shutdown command - quite often. Especially every night before automation testing starts. I checked the comp for viruses - did full scan using avast although I believed that the comp is clean. Any idea how to prevent the profile to get corrupted again? update So the first log entry in event log is today from 1.15am and one of my scripts ran runas command as administrator exactly at 1.15am. It was second time that runas war executed though after the testing started. The same happened second day in a row. Before the testing starts I need to copy one file that is locked. So I run handle.exe from runas to unlock it. That is what I think causing the profile to get corrupted. I am not able to reproduce it by myself. The message from event viewer is Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile. DETAIL – The process cannot access the file because it is being used by another process.

  Read the article

• mySQL sphinx Index location on Ubuntu

  - by Marcus Morris

  I am trying to test out a Sphinx cookbook, but I need a database to do so. I have created the database locally, but I need to know where the default path is for the index of the table I created. This is the error I am currently getting when trying to run sphinx because the path to the index is wrong: WARNING: index 'phoneindex': preload: failed to open /var/lib/mysql/mysql.sph: No such file or directory; NOT SERVING FATAL: no valid indexes to serve Where can I find mysql.sph? Or how/when is that file created? Thanks!

  Read the article

• Setup IIS 7 as FTP Server that is connectable outside of my local network

  - by Usta

  I was able to setup an FTP site that I was able to access via ftp://127.0.0.1/ or my local(static) ip. To do this I followed these instructions (with the exception that I did not bind to 127.0.0.1 as suggested) http://learn.iis.net/page.aspx/301/creating-a-new-ftp-site-in-iis-7/ I have created a firewall exception for port 20 and 21, and setup port-forwarding on my wireless router. But I can only access the site via local-host, and I need to have a friend have read access to it. So how do I enable remote access to it? (I'd rather not purchase a domain-name) My setup: IIS 7.5 Windows 7 Professional Wireless Network Norton Internet Security 2012 An Internal Static IP Address

  Read the article

• Fix for php 5.3.9 libxsl security "bug" fix

  - by Question Mark

  just this morning i updated my debian server to php 5.3.9 , change log (last item in list) has a fix for this bug and now when running any hosted site using XSL transforms i get: Warning: XSLTProcessor::transformToXml(): Can't set libxslt security properties, not doing transformation for security reasons I'm not using any <sax:output> tags in my xslt at all. Does anybody have any information on this, current chatter about it is thin, so i'm i little lost. Using the suggestion about switching ini settings on and off either side of -transformToXml(): ini_set("xsl.security_prefs", XSL_SECPREFS_NONE) or $xsl->setSecurityPreferences(XSL_SECPREFS_NONE) brings me back to the same error Many thanks. Progress: - Upgrading libxml and recompiling libxslt against the new version was a good suggestion, though has not fixed the issue. - Compiling the latest php5.3 snapshot does not fix the issue. Solution: I'm unsure what actually solved this, very sorry for anyone else having the same problem. firstly i upgraded libxml, then applied a few patches, then went into php source for the xsl parser and added some debugging and a few tweaks, after a few compiles getting the configure args right the error went away and wasn't reproducible. I would definitely recommend upgrading libxml as Petr suggested below and then grabbing the latest snapshot from php.net.

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17  | Next Page >