Monthly Archives

Articles indexed in November 2012

Page 414/450 | < Previous Page | 410 411 412 413 414 415 416 417 418 419 420 421  | Next Page >

• query keepalived

  - by tdimmig

  *Note: I have trouble deciding what should go in serverfault and what should go in superuser, if some kindly admin decides this is in the wrong place please move it for me - many thanks. I am implementing a basic HA system with keepalived. I only want to be notified of the failover in the case of hardware failure. I do, however, have the servers switch roles periodically. I have a track_script running on the backup that will vary it's return between 0 and 1 on an interval (once a week, once a month, whatever). Upon returning 0, the priority is raised above that of the master, upon returning 1 the priority is lowered again. This way they trade places on the configured interval. The question: What can I do to tell the difference between a switch caused by my script, and a switch caused because one of the servers died? I certainly want to be notified when there is an actual problem, but not every time the servers change places because of the script. I see that version 1.2.7 has snmp support and I may be able to use it to get some information that could tell me one way or another, but to be honest I've never used snmp before and I don't know how to get the information I want with it (my Google foo failed me).

  Read the article

• Windows file server access control by device

  - by Ori Shavit

  I'm trying to build a system where access to certain resources (file shares) in Windows Server, is limited not only by the username (in a Active Directory domain), but also by the client machine. So far, I haven't found a good way to do this; adding the computer account to the DACL is apparently not the way to do it. Windows Server 2012 supports this with Dynamic Access Control, but this method requires all clients to be Windows 8, it seems, with no way to use this with Windows 7 clients. Is there a supported way to do this? (or alternatively, add support for device authorization with Windows 7).

  Read the article

• Why is my ethernet interface in promiscuous mode

  - by nhed

  I read that seeing a flag of M in netstat -i is the way to tell which of your interfaces is in promiscuous mode I run it and I see that eth1 is in promiscuous mode $ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth1 1500 0 1770161198 0 0 0 57446481 0 0 0 BMRU lo 16436 0 97501566 0 0 0 97501566 0 0 0 LRU This seems to be the case on all the machines I checked (All Centos6.0, both virtual and physical), any idea why ethernet devices would be in such a mode unless someone was running any pcap based app (sudo lsof | grep pcap shows nothing)? I did not see any mention of promiscuous in any of the config files (sudo grep -r promis /etc) Any ideas what puts the interface into that mode and why? p.s. most of the posts I see seem to be security related, this is not that

  Read the article

• What can i do when my Ubuntu stucked [closed]

  - by Avihai Marchiano

  From time to time firefox cause to my Ubuntu machine to stuck.(nothing run on the machine except firefox) I cant move the mouse or move windows by keyboard. In some cases i have wait for a few minutes and than close last open tab in firefox and it solve the problem in other cases i do restart. Is there any way to prevent it, limit forefox in some way? In windows in most cased even with 100% cpu you can do alt-ctrl-delete and get the task manager, is there a top priority combination in linux that give you terminal? Or any other way ... Run on Ubuntux86 with GNOME , 2GB RAM, dual core cpu

  Read the article

• Two different sites, same IP, same top-level domain, on IIS 7.5 -- one works and the other displays HTTP 404 error

  - by user717236

  I'm running a Windows 2008 R2 box with IIS 7.5 as the web server. On IIS, I have two websites: mysubsite1.mysite.com and mysubsite2.mysite.com. There is only one IP on the server and both sites share this IP. Here is how I have the bindings configured: mysubsite1.mysite.com works fine. However, mysubsite2.mysite.com gives me the following error: Not Found HTTP Error 404. The requested resource is not found. Now, if I change the Host name field for mysubsite1.mysite.com to blank and restart the web server, both sites work! The question is why is the host name field for the first site causing an HTTP 404 error for the second site when both sites' Host name fields are filled? I would appreciate any insight. Thank you.

  Read the article

• Replication of lockoutTime attribute is not urgent on AD-LDS

  - by ixe013

  I have two LDS servers on the same subnet. They replicate well. If I change an attribute, it gets replicated after 15 seconds. LDS is configured to honor password policies. When a user makes too many wrong password attemps, his account is locked and that user's lockoutTime attribute is set accordingly. But lockoutTime is not replicated as urgent. In fact, it is not replicated unless there is another change somewhere in the directory. The lockoutTime attribute will be replicated. Here is an (edited Wireshark) trace. It shows normal replication trafic No. Time Protocol Length Info 133 16:23:02 DRSUAPI 562 DsGetNCChanges request 134 16:23:02 DRSUAPI 3042 DsGetNCChanges response 152 16:23:17 DRSUAPI 562 DsGetNCChanges request 157 16:23:17 DRSUAPI 242 DsGetNCChanges response 230 16:24:57 DRSUAPI 562 DsGetNCChanges request 231 16:24:57 DRSUAPI 2930 DsGetNCChanges response 246 16:25:12 DRSUAPI 562 DsGetNCChanges request Right after that, I lock the user (with a FOR loop and ldifde). Nothing happens, until I give up and change the description attribute on the user, then about 15 seconds later I see the replication go through. 1984 16:31:05 DRSUAPI 562 DsGetNCChanges request 1985 16:31:05 DRSUAPI 2930 DsGetNCChanges response The lockoutTime and description is replicated. As stated here, if I set lockoutTime to 0, replication occurs after 15 seconds ! I have enabled replication diagnostics, but nothing shows up in the instance's logs - strange. I have enabled change notification between sites, restarted both services, but I did not see any changes. How can I make the lockoutTime replication urgent ?

  Read the article

• Can't ping other machines at Linux VPN PPTP server's local lan from outside

  - by Marco Sanchez

  Before anything else, hello guys, this is the first time I ask for something here so I hope someone can give me a hand, please look at the following network diagram: --------------------------------------------------------------- VPN Server Webserver (SuSE SLES11) | | | ------- VPN LAN -------- | Router with Unique IP (With Port Forwarding rules set and VPN through enabled) | PPTP connection over Internet | Workstation (PC or Laptop with Windows) --------------------------------------------------------------- So the idea is for the workstation to connect to the PPTP Server and then be able to access a Web Application on the Webserver, right now I have the PPTP server configured and the VPN works, I can connect to the SLES11 server with no problems from the workstation and I can ping it and everything works fine but if I try to ping the Webserver from the workstation, I can't reach it, I'm making a mistake somewhere but I don't see where, please note that I'm not a network expert and thus I'd greatly appreciate some specific guidance. Here is some info related to the IPs --------------------------------------------------------------- *** SLES11 VPN Server has 2 Network cards: -- eth0 (Internal Network) IP: 192.168.210.5 MASK: 255.55.255.0 -- eth1 (External Network) IP: 192.168.1.105 MASK: 255.55.255.0 *** Webserver has 1 network card -- eth0 (Internal Network) IP: 192.168.210.221 MASK: 255.55.255.0 *** Workstation -- IP info once connection has been established to the VPN PPP adapter Test VPN Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Test VPN Connection Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.210.110(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : 189.209.208.181 (Defined as part of the PPTP Server options config script) 189.209.127.244 Primary WINS Server . . . . . . . : 192.168.210.220 (Defined as part of the PPTP Server options config script) NetBIOS over Tcpip. . . . . . . . : Enabled --------------------------------------------------------------- I also defined the following within IP tables: ------------------------------------------------------------- iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A INPUT -i eth0 -p tcp --dport 1723 -j ACCEPT iptables -A INPUT -i eth0 -p gre -j ACCEPT ------------------------------------------------------------- If you need any piece of information from the PPTP server scripts please let me know, the thing is that I can actually connect to the VPN server and access its services and everything but after that I can't reach any other computer on that LAN. Any help would be greatly appreciated and thanks in advance

  Read the article

• What prevents an attack on Postfix through its named pipes?

  - by Met?Ed

  What prevents an attack on Postfix through its named pipes by writing bogus data to them? I see on my system that they permit write access to other. I wonder if that opens Postfix to DoS or some other form of attack. prw--w--w- 1 postfix postdrop 0 Nov 28 21:13 /var/spool/postfix/public/pickup prw--w--w- 1 postfix postdrop 0 Nov 28 21:13 /var/spool/postfix/public/qmgr I reviewed the pickup(8) man page, and searched here and elsewhere, but failed to turn up any answers.

  Read the article

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• Hosting websites in our Workplace custom-built datacentre

  - by i.h4d35

  I'm faced with unique learning opportunity at work at the moment. Due to the slowdown (amongst other reasons), the powers that be at my office have decided to abandon our shared hosting providers (both shared and dedicated hosting) and have decided to host the websites at our office's datacentre. We're running 7 websites, wherein the average unique hits per day at the moment is about 900. We have 2 servers set aside for this - one is a DELL POWER EDGE 1850 (Intel Xeon 3 GHZ*2, 4GB RAM, 73GB HDD and the other is an HP DL 380 G3 (Intel Xeon 2.8 GHz, 6 GB RAM, 73 GB HDD) a) I would like to know the pros and cons of going ahead with this project.All the sites will be hosted on a single IP. In all probability, the OS is going to be CentOS. b) Do you think I should consider Virtualization into this equation (KVM/Xen)? I was thinking in terms of separate instances of the DB server and the frontend though I do not know if this is the best way to go. c) Should I be trying to use cloud stacks like OpenStack and try to make it look like websites hosted on some sort of Public Cloud? (something that I checked out here). Here is something else I came across, which looks similar to what needs to be done at our office. About the websites - Of the 7 websites, 4 are basic static websites which basically gives a whole lot of information about a few local institutions. The remaining 3 are local product-based websites developed in PHP wherein end user can view products and order them online. I am trying to take this as a learning experience wherein I can learn to build something from scratch and save the company a little something in the process. The migration needs to be completed by Easter so I guess it gives us some time (or am I being overly optimistic??). I am confused here and would appreciate all the help I can get. Thanks in advance.

  Read the article

• vCenter appliance won't use mail relay server

  - by Safado

  tl;dr: - sendmail is configured to use a relay server but still insists on using 127.0.01 as the relay, which results in mail not being sent. We have the open source vCenter appliance (v 5.0) managing our ESXi cluster. When connected to it via vSphere Client, you can configure the SMTP relay server to use by going to Administration > vCenter Server Settings > MAIL. There you can set the SMTP Server value. I looked through their documentation and also confirmed on the phone with support that all you have to do to configure mail is to put in the relay IP or fqdn in that box and hit OK. Well, I had done that and mail still wasn't sending. So I SSH into the server (which is SuSE) and look at /var/log/mail and it looks like it's trying to relay the email through 127.0.0.1 and it's rejecting it. So looking through the config files, I see there's /etc/sendmail.cf and /etc/mail/submit.cf. You can configure items in /etc/sysconfig/sendmail and run SuSEconfig --module sendmail to generate those to .cf files based on what's in /etc/sysconfig/sendmail. So playing around, I see that when you set the SMTP Server value in the vCenter gui, all that it does is change the "DS" line in /etc/mail/submit.cf to have DS[myrelayserver.com]. Looking on the internet, it would appear that the DS line is really the only thing you need to change in order to use a relay server. I got on the phone with VMWare support and spent 2 hours trying to modify ANY setting that had anything to do with relays and we couldn't get it to NOT use 127.0.0.1 as the relay. Just to note, any time we made any sort of configuration change, we restarted the sendmail service. Does anyone know whats going on? Have any ideas on how I can fix this?

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• How do I upgrade mongodb 1.8 to 2.2 on ubuntu?

  - by Alex Waters

  Following this guide: http://docs.mongodb.org/manual/tutorial/install-mongodb-on-ubuntu/ I ended up with mongodb 18 on my Ubuntu 10.04. I've just read the 2.2 mongodb release notes on upgrading and it says to just replace the binary. Would that be /usr/lib/mongodb/mongod ? It looks like the 2.2 tar has several files I might need to copy over: mongo, mongod, mongoexport, mongodump, mongofiles, mongoimport, mongorestore, mongos, xulwrapper Can I just copy and paste all of those over to replace the old versions of those files?

  Read the article

• zfs pool error, how to determine which drive failed in the past

  - by Kendrick

  I had been copying data from my pool so that I could rebuild it with a different version so that I could go away from solaris 11 and to one that is portable between freebsd/openindia etc. it was copying at 20mb a sec the other day which is about all my desktop drive can handle writing from the network. suddently lastnight it went down to 1.4mb i ran zpool status today and got this. pool: store state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scan: none requested config: NAME STATE READ WRITE CKSUM store ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c8t3d0p0 ONLINE 0 0 2 c8t4d0p0 ONLINE 0 0 10 c8t2d0p0 ONLINE 0 0 0 it is currently a 3 x1tb drive array. what tools would best be used to determine what the error was and which drive is failing. per the admin doc The second section of the configuration output displays error statistics. These errors are divided into three categories: READ – I/O errors occurred while issuing a read request. WRITE – I/O errors occurred while issuing a write request. CKSUM – Checksum errors. The device returned corrupted data as the result of a read request. it was saying low counts could be any thing from a power flux to a disk event but gave no suggestions as to what tools to check and determine with.

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• SQL 2008 R2 replication error: The process could not connect to Distributor

  - by Lance Lefebure

  I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

  Read the article

• AppCmd backup for IIS7 gives access denied error (hresult:80070005)

  - by TruMan1

  I have a script I have been using on another Windows 2008 to delete the IIS7 backup of configs and create a fresh one: SET DEST=C:\Backup\Web\IIS7 SET BACKUPNAME=IIS7-CONFIGS %windir%\system32\inetsrv\appcmd.exe delete backup "%BACKUPNAME%" %windir%\system32\inetsrv\appcmd.exe add backup "%BACKUPNAME%" robocopy %windir%\system32\inetsrv\backup "%DEST%" /MIR /R:6 /W:10 /ZB But on a new Windows 2008 server, I get an access denied on the delete: ERROR ( hresult:80070005, message:Command execution failed. Access is denied. ) I have UAC turned off and pretty much copied all the settings from the old server (including user role being an admin). What am I missing?

  Read the article

• Google Chrome "warn to quit" not warning on Cmd + Tab quit

  - by Theron Luhn

  As a Mac poweruser, I often use Cmd + Tab to switch between applications. Tab is unfortunately close to Q, so I often end up jamming Cmd + Q as well by accident. On most applications, this isn't a problem; a popup appears confirming if I want to quit, and I just click "cancel." However, this isn't the case with Google Chrome. I checked "warn before quitting", and when I press Cmd + Q a box saying "Hold Cmd + Q to quit" pops up. But when jamming Cmd + Q while switching to Chrome using Cmd + Tab, it completely ignores the "warn before quitting" policy and quits immediately. Any way to fix this annoyance? Switching either of the shortcuts to something else would fix the problem, but I'm not able to find a way to do so.

  Read the article

• dpkg -S not showing all files in package

  - by dimadima

  I've been using dpkg -S <package_name> to list the contents of a package. Sometimes I pipe to grep bin to quickly scan for executables. I just ran into a case where this didn't work out for me: $ which virtualenv $ sudo apt-get install python-virtualenv Reading package lists... Done ... Setting up python-virtualenv (1.7.1.2-1) ... $ which virtualenv /usr/bin/virtualenv $ dpkg -S /usr/bin/virtualenv python-virtualenv: /usr/bin/virtualenv $ dpkg -S python-virtualenv | grep bin $ /usr/bin/virtualenv seems to be provided by python-virtualenv, but isn't listed in the package contents provided by dpkg -S. All the while, passing /usr/bin/virtualenv to dpkg -S returns that the file comes from python-virtualenv. Can you all explain this?

  Read the article

• Regular Expression to replace part of URL in XML file

  - by Richie086

  I need a regular expression in Notepad++ to search/replace a string. My document (xml) has serveral thousand lines that look similar to this: <Url Source="Output/username/project/Content/Volume1VolumeName/TopicFileName.htm" /> I need to replace everything starting from Volume1 to .htm" / to replaced with X's or some other character to mask the actual file names in this file. So the resulting string would look like this after the search/replace was performed: <Url Source="Output/username/project/Content/Volume1XxxxxxXxxx/XxxxxXxxxXxxx.htm" /> I am working with confidential information that I cannot release to people outside of my company, but i need to send an example log file to a 3rd party for troubleshooting purposes. FYI the X's do not need to follow the upper/lower case after the replacement, i was just using different case X's for the hell of it :)

  Read the article

• How to update BIOS with efi?

  - by gasko peter

  We have a GA-H61M-DS2 rev 2.0 motherboard. It has an "F4" BIOS. We went to the vendors website: http://hu.gigabyte.com/products/page/mb/ga-h61m-ds2rev_20/download/bios and downloaded "F7", the latest BIOS version. We already tried: 1) "Efiflash.exe H61MDS22.F7" command from windows 7/32bit, it said nothing, the command line just flashed for a second.. 2) boot the win7 in "dos" mode (...) but the same thing happened. Q: How can we upgrade the BIOS? There aren't any ways for it?

  Read the article

• Digital audio does not work on MacBook Pro

  - by mathk

  I have a MacBook Pro (8,2). Using a TOSLINK cable I have no digital output. Oddly enough, sometime I can hear a glitch when I plug in the cable or when I give it a gentle wiggle. My guess is that the output is not correctly detecting that I have a digital link. So is there a way to force digital audio output on a MacBook Pro? Some say that in the Audio MIDI Setup there is an option but I can't find it. I am running OS X 10.7.5.

  Read the article

• How to get ~/foo from /home/user1/foo?

  - by Claudius

  The Bash prompt supports the \w escape sequence, documented as \w the current working directory, with $HOME abbreviated with a tilde (uses the value of the PROMPT_DIRTRIM variable) Is there any way to get a similar abbreviation for an arbitrary string? That is, is there a general command that does something like the following, provided that HOME=/home/user1 /home/user1 ? ~ /home/user1/a/1 ? ~/a/1 /home/user2/b/2 ? ~user2/b/2 /root ? ~root Sure, I could try something ugly with sed, but that is unlikely to give me the result I want in any case. :-) The movitation behind this is that I would like to keep the titles in the tabs of my terminals as short as possible, hence abbreviate working directories where possible.

  Read the article

• Reset rc.d so software starts at boot again

  - by natli

  I ran the following 2 commands on my VPS box and now it boots without starting any software at all. According to rcconf it's still supposed to start my chosen software (ssh etc.) but it doesn't. update-rc.d vz defaults update-rc.d vzeventd defaults I already tried removing them again with update-rc.d -f vz remove update-rc.d -f vzeventd remove But that didnt't change anything. /etc/rc.local also still correctly lists some scripts I want to run at start-up, but they don't seem to be called either. I expect the top 2 commands to be responsible, but here's everything I did: mkdir /var/openvz-dl cd /var/openvz-dl wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-devel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-core-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-lib-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/vzquota/3.1/vzquota-3.1-1.x86_64.rpm apt-get install fakeroot alien fakeroot alien --to-deb --scripts --keep-version vz*.rpm ploop*.rpm dpkg -i vz*.deb ploop*.deb --force-overwrite update-rc.d vz defaults update-rc.d vzeventd defaults reboot A huge part of that failed because I was running it on an OpenVZ VPS which has a shared kernel that can't be altered, so I also had to fix the dpkg like so (it was moaning about wanting to install vzkernel with a package not being found); rm /var/lib/dpkg/info/vzkernel* dpkg-reconfigure vzkernel --force dpkg --purge --force-all vzkernel But that didn't fix the boot issue either. How do I make my software start at boot again?

  Read the article

• How do brand laptop manufacturers restrict hard disk drive?

  - by user176705

  I'm curious to know, when I bought a brand new laptop there are limitations to create or change the HDD partitions, except the following partitions: c:\ drive (Main partition + OS drive) NTFS. 400 Gb. Recovery drive NTFS. 15 Gb. Tools drive FAT32. 2 Gb. System drive NTFS. 0.3 Gb. My questions are: How do manufacturers restrict HDDs ? What is the term for these restrictions? Can this be applied to desktop PCs? Is it possible to modify the restrictions by an end-user?

  Read the article

< Previous Page | 410 411 412 413 414 415 416 417 418 419 420 421  | Next Page >