Daily Archives

Articles indexed Saturday November 9 2013

Page 6/15 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • What does this beep code mean?

    - by Jaspack
    When I wanted to start my laptop today (an Acer Aspire 8920G), the laptop started beeping. I know this beeping is a POST error code, but I can not figure out which one it is. The motherboard of the laptop is manufactured by Phoenix, so I looked up these POST codes: http://www.bioscentral.com/beepcodes/phoenixbeep.htm The beeping is in the form 1-1-1-1 (short beeps, repeating and even without ending), but this code is not mentioned by the manufacturer. Does anybody know what could be the problem? I don't know if it is relevant, but since a couple of months the CMOS battery was degrading. The laptop couldn't keep track of the time. Maybe a failing CMOS battery could be the problem?

    Read the article

  • RTNETLINK answers: File exists... maybe because assigned a new mac adress

    - by steven
    I got a "RTNETLINK answers: File exists Failed to bring up eth0:1" on "ifup eth0:1". I suspect it happens because i assigned a new mac adress in my VM's network adapter. Can you tell me how to fix the issue? My configuration looks like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.1.80 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 192.168.1.1 # Alias being connected to 192.168.10.x Network auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 Why do I get "RTNETLINK answer: File exists.." suddenly? I worked with this configuration before without problems. All i did in the past is to renew the adapters mac adress. At the moment I am connected to the 192.168.10.x Network and if I do /etc/init.d/networking stop /etc/init.d/networking start then i got "RTNETLINK [...] falied to bring up eth0:1" but the strage thing is that i am able to connect to 192.168.10.83 via ssh from my host machine. But I cannot reach the internet from the debian client. I hope it is clear what my problem is, now. update if i change my /etc/network/interfaces like this then "ifup eth0" fails, too with the same error! # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 with verbose option enabled i got: Configuring interfache eth0=eth0 (inet) run-parts --verbose /etc/network/if-pre-up.d ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0 RTNETLINK answers: File exists Failed to bring up eth0. same if i type this manually: ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0

    Read the article

  • What is the correct cipher name for RC4 in Chrome?

    - by qbi
    I want to remove RC4 from Google Chrome and found the commandline option --cipher-suite-blacklist. However I wasn't able to figure out what the correct notation for RC4 is. Whatever I tried so far only brought the message: ERROR:ssl_config_service_manager_pref.cc(55)] Ignoring unrecognized or \ unparsable cipher suite: Even the names listed in ssl_cipher_suite_names.cc don't work. What should I enter to remove RC4 as a cipher for SSL/TLS? I'm working with some different versions of GNU/Linux and sometimes also with Windows. So it would be nice if the command-line argument would work under all OSes. I used the following command: chrome --cipher-suite-blacklist=TLS_RSA_WITH_RC4_128_MD5 --ssl-version-min=tls1.1 chrome --cipher-suite-blacklist=RC4 --ssl-version-min=tls1.1 chrome --cipher-suite-blacklist=0xXYZ,0xUVW --ssl-version-min=tls1.1 # XYZ and UVW are some hexadecimal numbers

    Read the article

  • How do I remove a USB drive's write protection?

    - by nate
    I have a SanDisk Cruser Blade USB stick that suddenly seems to be write protected. I tried running DiskPart but after I write the command "attributes disk clear readonly" it displays this: Microsoft DiskPart version 5.1.3565 ADD - Add a mirror to a simple volume. ACTIVE - Marks the current basic partition as an active boot partition. ASSIGN - Assign a drive letter or mount point to the selected volume. BREAK - Break a mirror set. CLEAN - Clear the configuration information, or all information, off the disk. CONVERT - Converts between different disk formats. CREATE - Create a volume or partition. DELETE - Delete an object. DETAIL - Provide details about an object. EXIT - Exit DiskPart EXTEND - Extend a volume. HELP - Prints a list of commands. IMPORT - Imports a disk group. LIST - Prints out a list of objects. INACTIVE - Marks the current basic partition as an inactive partition. ONLINE - Online a disk that is currently marked as offline. REM - Does nothing. Used to comment scripts. REMOVE - Remove a drive letter or mount point assignment. REPAIR - Repair a RAID-5 volume. RESCAN - Rescan the computer looking for disks and volumes. RETAIN - Place a retainer partition under a simple volume. SELECT - Move the focus to an object. It's like when you type help at the DiskPart prompt, so how do I get past this? This problem started when I plugged the stick into a laptop which had viruses, if that's any help.

    Read the article

  • Error- D:\ is not accessible. Access is denied

    - by Aaron
    All of the sudden the D drive gives me an error when I try to open it: D:\ is not accessible. Access is denied. I have files on the drive that I would like to recover, so I do not want to reformat the drive. It acts almost like the computer doesn't recognize the drive. I have a feeling it's something with security settings, I may have accidentally changed something on the drive. I'm running on a Acer Aspire laptop on Windows Vista, SP2. I beleive both the C and the D drive run off of the same disk drive. At least that's all the Device Manager shows. So correct me if I'm wrong, but that would make it a partitioned drive.

    Read the article

  • Third monitor randomly defaults to 640 x 480 on startup

    - by ajbdev
    I purchased a PowerColor HD 5770 video card so I could get a third monitor working. I have two widescreen monitors, one attached via HDMI and the other attached via DVI. My third monitor is attached from DisplayPort to VGA (using a passive connector like this one) The third monitor is a 19" Hyundai L90D. I was unable to find any Windows 7 (or Vista for that matter) drivers for the monitor, so it's stuck with "Generic Non-PNP Monitor". It's native resolution is 1280 x 1024. Randomly Windows will boot up in the correct native res, but sometimes it boots up in 640 x 480 res. When it does boot up into 640 x 480 res, the screen resolution slider is stuck and I cannot slide it back to 1280 x 1024. I cannot find a pattern for when or why it will do this, I've tried rebooting five or six times in a row at times to get it to boot into native res, but this doesn't always work.

    Read the article

  • managing information/functionality on shared common project classes

    - by ilansch
    In my company, we have a common solution the contains common projects (2 projects so far, one for .net 3.5 and one for .net 4.5). My main problem is that during time, a lot of code is added, for example hosting a process as windows service is a class called ServiceManagement, But no one but the developer knows it, and if someone wants to use this shared class, he does not know it exist. So i am looking for a way to document and manage all the classes with tags, a 3rd party util/web util, that i can search for tags and maybe find common classes that i can use (if we keep all our code well-documented). Does anyone familiar with sort of tools ?

    Read the article

  • ViewController in programming

    - by Vishwas Gagrani
    ViewController is a term for classes that handle views in a framework. This is especially used in MVC frameworks. I go through various projects, written by various programmers, who implement MVC in different ways. Especially, i get confused, about the relation between the MainView ( parent view ) and some CustomView ( widget etc) in the framework. I personally pass reference of the MainView into the ViewController to be instantiated. All the subviews of ViewController are added to that reference of MainView. Additionally, ViewController itself is added as a child of MainView. Like this : Want to know, if this is the right way to relate each other ?

    Read the article

  • What is the advantage of currying?

    - by Mad Scientist
    I just learned about currying, and while I think I understand the concept, I'm not seeing any big advantage in using it. As a trivial example I use a function that adds two values (written in ML). The version without currying would be fun add(x, y) = x + y and would be called as add(3, 5) while the curried version is fun add x y = x + y (* short for val add = fn x => fn y=> x + y *) and would be called as add 3 5 It seems to me to be just syntactic sugar that removes one set of parentheses from defining and calling the function. I've seen currying listed as one of the important features of a functional languages, and I'm a bit underwhelmed by it at the moment. The concept of creating a chain of functions that consume each a single parameter, instead of a function that takes a tuple seems rather complicated to use for a simple change of syntax. Is the slightly simpler syntax the only motivation for currying, or am I missing some other advantages that are not obvious in my very simple example? Is currying just syntactic sugar?

    Read the article

  • Setting umask globally

    - by DevSolar
    I am using a private user group setup, i.e. a user foo's home directory is owned by foo:foo, not foo:users. For this to work, I need to set the umask to 002 globally. After a quick grep -RIi umask /etc/*, it seemed for a moment that modifying the UMASK entry in /etc/login.defs should do the trick. It does, too -- but only for console logins. If I log in to my desktop, and open a terminal there, I still get to see the default umask 022. Same goes for files created from apps started through the menu. Apparently, the display manager (or whatever X11 component responsible) does source some different setting than a console login does, and damned if I could tell which one it is. (I tried changing the setting in /etc/init.d/rc, and no, it did not help.) How / where do I set umask globally, so that the X11 desktop environment gets the memo as well?

    Read the article

  • No WIFI on Ubuntu 12.04 LTS after today software update

    - by Adchara
    I just got new dell inspiron3537 with Ubuntu 12.04 LTS (no windows O/S). It got some wireless (hard block) yesterday. So, this morning, I ran the software update all the security update. After that I can't see "Wireless" in system setting. So, I updated all the software update and looked thru several web site and found "sudo lshw -c network" command. I tried and found the result below. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: 74:86:7a:40:5d:48 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.10 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:60 ioport:4000(size=256) memory:c0700000-c0700fff memory:c0400000-c0403fff *-network UNCLAIMED description: Network controller product: QCA9565 / AR9565 Wireless Network Adapter vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0600000-c067ffff memory:9fb00000-9fb0ffff Please suggest what I should do to fix it. Thx in advance

    Read the article

  • Wrong package for Idle-python2.7?

    - by adelval
    I'm running python 2.7 in Ubuntu 3.10, and idle (idle-python2.7) has stopped working. Whenever I try to open a file in a editor window, it is blank, though the file does exist and is not empty/blank. Furthermore, it is not possible to close idle after this, except via a terminal kill command. Idle was working fine before. The problem appeared after I installed a number of things, including idlex, various scipy modules and mpmath, but after trying to repair it in several ways, it seems to be caused by Ubuntu's official idle package. I get this error in the terminal when trying to open a file in idle: Exception in Tkinter callback [...lines ommitted for brevity...] File "/usr/lib/python2.7/idlelib/IOBinding.py", line 129, in coding_spec for line in lst: NameError: global name 'lst' is not defined If you look at the code, it looks like an obvious bug: indeed lst is not defined in the function coding_spec. Furthermore, the source file IOBinding.py in http://fossies.org/dox/Python-2.7.5/IOBinding_8py_source.html is different and doesn't show the problem. Thinking that one of the recently packages had overwritten the file somehow, I've tried a number of things, including reinstalling all Python packages from synaptic, but the wrong IOBinding.py is still there. The reason I think the problem lies with the package itself is that I finally did sudo apt-get remove idle, verified that the idlelib directory was empty, and reinstalled with sudo apt-get install idle; but the wrong IOBinding.py file came back again. I can in fact make idle work again by simply replacing lst by str in the code, but to me that's clearly a no-no. I'm not to happy either about trying to replace just that file from the source python distribution, as other files may be wrong. I want to get the right files from the official package.

    Read the article

  • Where does the YouTube video files stored on system nowadays?

    - by souravc
    When I open a youtube video with firefox I could not find any video file inside ~/.mozilla/firefox/<some_string>.default/Cache/. I also tried with google-chrome like, ps ax | grep flash ls -l /proc/[*PID*]/fd | grep Flash But again /proc/[*PID*]/fd does not have any video like file. ls -l /proc/[*PID*]/fd have some results like lrwx------ 1 root root 64 Nov 9 12:18 22 -> /run/shm/.com.google.Chrome.eOsHNu (deleted) lrwx------ 1 root root 64 Nov 9 12:18 23 -> /run/shm/.com.google.Chrome.p8h6BL (deleted) Result of ls -l /proc/[*PID*]/fd | grep Flash for some videos from other site is like lrwx------ 1 root root 64 Nov 9 12:35 26 -> /home/username/.config/google-chrome/Default/Pepper Data/Shockwave Flash/.com.google.Chrome.QMzxP8 (deleted) But could not be copied. Then what are the places where firefox or google-chrome stores the streaming videos? And is it possible to recover(copy) a video from there to watch them offline? P.S I have other ways(downloaders) to have streaming videos, but my question is very specific.

    Read the article

  • How do I fix "Grub Rescue"? Uninstallation?

    - by Julien Mackenzie
    I am currently dual-booting windows 7 and Ubuntu. I am about to sell my computer so I was following a tutorial on how to uninstall Ubuntu. I had deleted my partitions like the tutorial said and now I get this: error : no such partition grub rescue_ I am now looking for help on Getting out of this "grub rescue" Uninstalling Ubuntu and/or factory reset Notes -Newbie - No windows disks -I have spare CDs

    Read the article

  • How to install downloaded Canon ScanGear

    - by GreenSee
    I have newly installed Ubuntu 12.04. I have Canon MG6360 printer/scanner. I have successfully installed printer drivers and can print okay. Have downloaded MG6300 series ScanGear MP Ver. 2.00 for Linux (deb) from Canon but don't know how to install this from terminal. I apologise for having to ask such a basic question! Thanks. Later...I have extracted the files. Question appears: Do I want to run install.sh? I click 'run in terminal', and enter password. I don't know if it installed and don't know how to check. Scanner does not work or 'see' the PC. Any advice would be greatly appreciated.

    Read the article

  • Eclipse ADT: Layout Properties Editor doesn't work correctly

    - by NullNoname
    I have a new, clean installation of Eclipse Kepler (4.3.1) SR1 (x64) in Linux Mint 15 Olivia x64 (based on Ubuntu 13.04 “Raring Ringtail”). ADT version is 22.3.0, and Java is Oracle's 1.7.0_45. The problem is, I cannot edit the properties in layout editor; nothing happens when I click "..." button, nor I can edit the properties directly by clicking the empty space. The boolean properties don't even contain the checkbox. This doesn't happen in Windows XP 32bit, with the same versions of Eclipse and ADT: Anyone know any workarounds/reasons for this? Looks like Mac OS X Mountain Lion had a similar issue in the past, but I heard that was fixed, and I'm talking about Linux version here. I had no such problems in Eclipse Indigo and an old version of ADT, but I can't remember the exact versions of them. EDIT: Lubuntu 13.04 (32bit) in VMware Player doesn't have this problem.

    Read the article

  • 13.10 doesn't boot on Vaio Pro 13

    - by vaioonbuntu
    I just installed Ubuntu 13.10 on my new Vaio Pro 13, disabled safe mode, but used UEFI and not legacy mode. I did an encrypted LVM installation and erased the complete SSD. It booted just fine from USB, but after installation it doesn't boot. The Vaio failed boot screen appears. I then tried this advice here: 13.10 on vaio pro with UEFI sadly it fails for me with "/usr/sbin/grub-probe: error: failed to get canonical path of /cow." I then tried mounted the encrypted partition with Nautilus and tried this: Cannot update grub with paramters on live USB With /dev/sda2 and then to install GRUB to /dev/sda. Didn't succeed and warned me that the "GPT partition label contains no BIOS Boot Partition; embedding won't be possible" What do i have to do, go fix GRUB and be able to boot my finished install? Here's my Boot Repair Log: http://paste.ubuntu.com/6386598/ I would really appreciate any help, I'm so happy to finally be able to ditch my big fat Macbook Pro and use Ubuntu on my new, light Vaio Pro, if only I could fix GRUB. best, x

    Read the article

  • failed upgrade to ubuntu 13.10!

    - by user212282
    Okay so I went to upgrade to 13.10 and after some time went by my computer restarted.. I assumed since it need to due to the upgrade.. but once it came back on all that shows up is the desk top amd 2icons one for a game amd one for torrents. .. but NOTHING ELSE!!!! I can't open anything I also have to toolbar on the top where the date amd time would be and no launcher on the side for my icon shortcuts I basically can't do anything! Any help would be awesome I can't even get terminal to open via cnt-alt-t

    Read the article

  • Scid Chess Program Compiling issue

    - by lbochitt
    First of all I would like to point that I'm new to Ubuntu so sorry if what I am asking is ridiculous. I have downloaded Scid 4.4 chess program and I have tried to compile it as it was explained on its website: 1) Initialize git. 2) Create a folder where you want to download and (?) compile the source, then cast: git init on your command line. 3) You're now ready to download the sources recall Fulvio's spell: git clone git://scid.git.sourceforge.net/gitroot/scid/scid This should get you the latest Scid source. 4) You're now ready to compile Scid. In principle, all you need to do is: ./configure and then make 5) If you get stuck, you probably need to get developer versions of tcl/tk. This translates into issuing these three commands: sudo apt-get install tcl8.5-dev sudo apt-get install tk8.5-dev sudo apt-get install zlib1g -dev 6) You should now be ready to compile The problem is that when I run ./configure to start compiling the following message appears on Terminal: configure: Makefile configuration program for Scid Tcl/Tk version: 8.5 Your operating system is: Linux 3.8.0-19-generic Location of "tcl.h": /usr/include/tcl8.5 Location of "tk.h": /usr/include/tcl8.5 Location of Tcl 8.5 library: not found Location of Tk 8.5 library: not found Checking if your system already has zlib installed: yes. Using Makefile.conf. Not all settings could be determined! The default Makefile was written. You will need to edit it before you can compile Scid. What should I do? Has anybody faced this problem before? Thanks in advance I have run ls -l /usr/include/tcl8.5/tcl.h here's the result: -rw-r--r-- 1 root root 87291 abr 22 10:45 /usr/include/tcl8.5/tcl.h I have also tried what you suggested Could you run git reset --hard HEAD and git clean -d -f to clean up everything using Git? Then run ./configure again. Just a shot in the dark - I've seen some GNU automake stuff still listening to its "cached" version of the results or something. Still no solution. I don't know why it can't recognize the library though it is installed I opened configure to see where the program looked for the library. This is the code: # libraryPath: List of possible locations of Tcl/Tk library. set libraryPath { /usr/lib /usr/lib64 /usr/local/tcl/lib /usr/local/lib /usr/X11R6/lib /opt/tcltk/lib /usr/lib/x86_64-linux-gnu } lappend libraryPath "/usr/lib/tcl${tclv}" lappend libraryPath "/usr/lib/tk${tclv}" lappend libraryPath "/usr/lib/tcl${tclv_nodot}" lappend libraryPath "/usr/lib/tk${tclv_nodot}" # Try to add tcl_library and auto_path values to libraryPath, # in case the user has a non-standard Tcl/Tk library location: if {[info exists ::tcl_library]} { lappend headerPath \ [file join [file dirname [file dirname $::tcl_library]] include] lappend libraryPath [file dirname $::tcl_library] lappend libraryPath $::tcl_library } if {[info exists ::auto_path]} { foreach name $::auto_path { lappend libraryPath $name } } if {! [info exists var(TCL_INCLUDE)]} { puts -nonewline { Location of "tcl.h": } set opt(tcl_h) [findDir "tcl.h" $headerPath "TCL_VERSION.*$tclv"] if {$opt(tcl_h) == ""} { puts "not found" set success 0 set opt(tcl_h) "$::defaultVar(TCL_INCLUDE)" } else { puts $opt(tcl_h) } } set opt(tcl_lib) "" if {! [info exists var(TCL_LIBRARY)]} { puts -nonewline " Location of Tcl $tclv library: " set opt(tcl_lib) [findDir "libtcl${tclv}.*" $libraryPath] if {$opt(tcl_lib) == ""} { set opt(tcl_lib) [findDir "libtcl${tclv_nodot}.*" $libraryPath] if {$opt(tcl_lib) == ""} { puts "not found" set success 0 set opt(tcl_lib) "$opt(tcl_h)" set opt(tcl_lib_file) "tcl\$(TCL_VERSION)" } else { set opt(tcl_lib_file) "tcl${tclv_nodot}" puts $opt(tcl_lib) } } else { set opt(tcl_lib_file) "tcl\$(TCL_VERSION)" puts $opt(tcl_lib) } } if {! [info exists var(TCL_INCLUDE)]} { set var(TCL_INCLUDE) "-I$opt(tcl_h)" } if {! [info exists var(TCL_LIBRARY)]} { set var(TCL_LIBRARY) "-L$opt(tcl_lib) -l$opt(tcl_lib_file)" } return $success So I guess (And by guess I mean i have no idea how to code) I should write somewhere in here usr/lib/tcl8.5 and usr/lib/tk8.5, am I right?

    Read the article

  • nouveau Unknown Fermi chipset

    - by Abood Mount
    I've installed a fresh install of Ubuntu 13.04 and whenever I start my laptop I get this output error [ 19.469816] nouveau ![ DEVICE][0000:01:00.0] unknown Fermi chipset [ 19.469846] nouveau E[ DEVICE][0000:01:00.0] unknown chipset, 0x0d7000a2 [ 19.469870] nouveau E[ DRM] failed to create 0x80000080, -22 [ 19.470095] nouveau: probe of 0000:01:00.0 failed with error -22 I have Lenovo G580 with nVidia Geforce 710m.

    Read the article

  • unable to connect mobile broadband ubuntu 12.10

    - by Anurag Srivastava
    i recently installed ubuntu 12.10 on my desktop. now the mobile connection was not working, which i later found out to be a bug in modem manger so i downgraded it to v0.5.2 but still the problem persists. whenever i try connecting, the mobile broadband option gets automatically disabled. i have a bsnl EVDO connection, which i had to manually configure as the device was not automatically detected at first.

    Read the article

  • Apache could not reliably determine server

    - by frqcuse
    Apache cannot fully determine domain name when I tried restarting after install. I get this error; sudo /etc/init.d/apache2 restart *Restarting web server config apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName. Why I'm I seeing 127.0.1.1 I have tried saving ServerName localhost into my /etc/init.d/apache2 but it keeps redirecting me to google search page everytime I type phpmyadmin. Will appreciate an expert help?

    Read the article

  • Set a drawing viewport while using camera

    - by Mariano
    I'm working with XNA. I already have a basic world made of tiles and a camera using a transform matrix. I have a character moving around and the camera follows. What I want to do now is draw the map only on a certain part of the screen as shown on the figure below. This way I can move the map to the left of the screen and have the other fixed parts shift to the right. Do I need to modify the camera matrix? Make a new viewport?

    Read the article

  • Using Crypt function Python 3.3.2

    - by adampski
    In Windows and Python version 3.3.2, I try and call the python module like so: hash2 = crypt(word, salt) I import it at the top of my program like so: from crypt import * The result I get is the following: Traceback (most recent call last): File "C:\none\of\your\business\adams.py", line 10, in <module> from crypt import * File "C:\Python33\lib\crypt.py", line 3, in <module> import _crypt ImportError: No module named '_crypt' However, when I execute the same file adams.py in Ubuntu, with Python 2.7.3, it executes perfectly - no errors. I tried the following to resolve the issue for my Windows & Python 3.3.2 (though I'm sure the OS isn't the issue, the Python version or my use of syntax is the issue): Rename the directory in the Python33 directory from Lib to lib Rename the crypt.py in lib to _crypt.py. However, it turns out the entire crypt.py module depends on an external module called _crypt.py too. Browsed internet to download anything remotely appropriate to resemble _crypt.py It's not Python, right? It's me...(?) I'm using syntaxes to import and use external modules that are acceptable in 2.7.3, but not in 3.3.2. Or have I found a bug in 3.3.2?

    Read the article

  • WCF Service timeout in Callback

    - by Muckers Mate
    I'm trying to get to grips with WCF, in particular writing a WCF Service application with callback. I've setup the service, together with the callback contract but when the callback is called, the app is timing out. Essentially, from a client I'm setting a property within the service class. The Setter of this property, if it fails validation fires a callback and, well, this is timing out. I realise that this is probably to it not being an Asynchronous calback, but can someone please show me how to resolve this? Thanks // The call back (client-side) interface public interface ISAPUploadServiceReply { [OperationContract(IsOneWay = true)] void Reply(int stateCode); } // The Upload Service interface [ServiceContract(CallbackContract = typeof(ISAPUploadServiceReply))] public interface ISAPUploadService { int ServerState { [OperationContract] get; [OperationContract(IsOneWay=true)] set; And the implementation... public int ServerState { get { return serverState; } set { if (InvalidState(Value)) { var to = OperationContext.Current.GetCallbackChannel<ISAPUploadServiceReply>(); to.Reply(eInvalidState); } else serverState = value; } }

    Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >