Daily Archives

Articles indexed Tuesday December 18 2012

Page 9/17 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

  • Macintosh computers cannot connect to router unless we re-start the modem and router

    - by dwwilson66
    We have a small office network with DSL and a Netgear WNR-2000 wireless router acting as a DHCP server. There are nine devices connected to the router, wirelessly and wired. Whenever a Mac computer tries to connect, it's unsuccessful until we restart the router. Each of the possible devices that can connect to the network is listed in a table to assign certain IP addresses to certain MAC addresses. I am running WPA-PSK security. I can view the router status and see that the Mac's MAC address is visible to the router, but with a 169.* IP address, even though I'm assigning its MAC address to an IP address within my subnet. All non-Mac devices attached to the network connect properly, and can access the network properly even AFTER the Mac has not successfully connected. The network includes Windows devices, Roku boxes, printers and internet ready TVs. This to me, would point to a DHCP issue with how Mac communicates with my network. One interesting thing to note is that if a Mac connects and is prevented from sleeping, it will stay connected indefinitely; reissuing the security cert from the router works fine. I'm not sure if that's supposed to sever & re-establish a connection with the updated credentials or not, but I do stay connected. If the Mac sleeps and is awakened while the security cert is still valid, it connects fine. If the security certificate expires while the Mac is asleep, we need to restart the router. Restarting the router will ALWAYS assigns the proper IP addresses to the Mac equipment. I have heard anecdotally that Mac doesn't play well with 802.11n; I have not tested any other Wireless protocols. There's a couple issues here: First, I found this on Stack, Mac laptop crashing wireless router, but it's not rally applicable since the router isn't crashing. But, it does give some clues about Mac's accessing the network. I did change my encryption from WEP to WPA-PSK, but after about a week, we're still experiencing the issue. I'm not really sure if there's anything else useful in that question. Second, I'm considering getting a 802.11c router and hooking it up to the wireless N router. the 802.11c router would handle all the Mac traffic, and would be set up as a Mac-only subnet. Everything else would remain as is. However, I'm not sure if this is doable on a technology level...do I need a bridge or is this some way to do this with regular consumer gear?

    Read the article

  • vSwitch configuration with 12 uplinks

    - by Joshua
    I have been doing a lot of research on vSwitch configurations, but I think I am more confused now after all of the reading that I have done. So here is my situation 3 ESX Hosts (12 nics each), 1 iSCSI SAN, 2 Force 10 switches. Should I create individual vSwitches for MGMT, vMotion, VM, and SCSI traffic? or do I need to group anything together in the same vSwitch? I am going to have 4 vLANS total, one for each of those items, do I need to do any trunking on the physical switch or just assign the correct vLAN to each physical switch port?

    Read the article

  • iptables blank after reboot

    - by theillien
    We've started encountering an issue with iptables on our RHEL 6.3 systems in that after a reboot, when the service starts, the rules are not loaded. We get the empty ruleset: [msnyder@matt-test ~]$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is in spite of the fact that we have rules defined and the service is, indeed, running. That I know because when I run service iptables start it simply drops back to the prompt. If I run service iptables restart it actually stops and then restarts the service. And, of course, if I run service iptables stop it indicates that iptables is actually stopping. Knowing that I need to restart the service, I do so and the rules load up properly. They simply don't get loaded after a reboot. Unless they get loaded differently during a reboot I don't see how our rules would be wrong. If they were, they wouldn't even load during a service restart. Has anyone else ever encountered this? EDIT: The rules are already saved in /etc/sysconfig/iptables. They are not added on the fly from the command line so service iptables save is unnecessary.

    Read the article

  • My Graphics Card isn't working Properly

    - by Dan
    I have just upgraded from a Sapphire AMD 6670 2gb Graphics card to a Nvidia GTX 650 ti 2gb SSC and my Windows Experiance index has gone from 6.8 to 7.7 but when playing games i am seeing no improvements i cannot play saints row three on even the lowest settings but according to many people and benchmarks on the web i should be able to play it comfortably. I want to know why this is happening to me..... I have installed the latest drivers and i have direct 10 + 11 installed I am 15 and it's my birthday today as i got it as a present but its not doing what i want also in am using a dvi cable not hdmi because i need a new one and its in the post. Is it possible that using dvi will affect performance

    Read the article

  • Determining physical location of data on a disc

    - by Synetech
    Does anybody know of a way to find out where, physically on a CD or DVD a given piece of data would be located? I am trying to watch a DVD at the moment, and am about half-way through, but it keeps dying at a specific spot in the film, presumably because of a scratch. I have a repair kit, but I don’t know where to focus my repair because there are several scuffs and scratches on the disc and I have no way of knowing which one is causing the issue. Obviously, cleaning all of them is inadvisable because not only does it waste the consumable materials in the kit, but not all of them are a problem, and by working them, some may become unreadable. Moreover, just because I am half-way through the movie does not mean that it would be half-way from the hub to the edge for several reasons: Discs have more data towards the outer edge than the inner edge (circles are more mathematically complicated than rectangles) The disc is not completely filled up (and even if it were, the movie itself would be be using it all, there are extras and such) Because in this particular case it is a commercial DVD, it is also dual-layer which further complicates manual determination As such, I am trying to find a program that can let me identify a file (or part thereof), cluster, etc. and show me a picture of where on the CD/DVD it would be located. That way, I can look at the disc and fix any scratches that correspond to that distance from the hub. For example, the image below might indicate where on a disc a couple of files or range of clusters would be located, so by looking for anomalies in those areas (rotating as necessary), the correct one can be identified. I’m sure it can be done since at least one form of copy protection (DPM) uses it and DVD-lab Pro includes a “DVD Topology” feature to do this.

    Read the article

  • How to connect Android phone to a Wifi network using PPPoE?

    - by Slavo
    I have an ISP at home, which provides me with a PPPoE connection. My router supports that and I've configured it to autoconnect periodically, so I don't have to type my username and password each time. When I connect to the Wireless router from the PC, I have internet and everything works fine. However, when I do so using my Android phone, there's no internet connection on the phone. It connects to the router, but I cannot open any web page. How can I enable internet access from such an ISP on my phone? Is it something in the router setup? The router is Linksys WRT54GL.

    Read the article

  • OpenWRT based gateway with dnsmasq and internal server with bind

    - by Peter
    I have router based on OpenWRT which has dnsmasq 2.59. Inside my local area network I have a NS server bind. This server has internal and external views for a couple of my domains. My router forwards port 53 TCP and UDP from outside IP (router WAN) to this server. For the external clients everything works fine. In order to organize the internal view, I decided to add the exception to /etc/dnsmasq.conf server=/mydomain1.com/192.168.1.1 server=/mydomain2.com/192.168.1.1 server=/mydomain3.com/192.168.1.1 (192.168.1.1 - IP address of the NS server) According to dnsmasq manstrong text: More specific domains take precendence over less specific domains, so: --server=/google.com/1.2.3.4 --server=/www.google.com/2.3.4.5 will send queries for *.google.com to 1.2.3.4, except *www.google.com, which will go to 2.3.4.5 this domain name with all the sub-domains is supposed to be forward to my NS server. Everything works (SOA, NS, MX, CNAME, TXT, SRV etc.) except for A-record: # nslookup -type=a mydomain1.com Server: 192.168.1.100 Address: 192.168.1.100#53 *** Can't find mydomain1.com: No answer 192.168.1.100 - IP address of my router (dnsmasq) However, I can get the answer for the TXT-record query: # nslookup -type=txt mydomain1.com Server: 192.168.1.100 Address: 192.168.1.100#53 mydomain1.com text = "v=spf1 include:mydomain1.com -all" When I just specify the local IP of my NS server (direct access to the server without using dnsmasq) then the results are: # nslookup -type=a mydomain1.com 192.168.1.1 Server: 192.168.1.1 Address: 192.168.1.1#53 Name: mydomain1.com Address: 192.168.1.1 There is a similar situation with the MX-record: C:\>nslookup -type=mx mydomain1.com Server: router.lan Address: 192.168.1.100 mydomain1.com MX preference = 10, mail exchanger = mail.mydomain1.com mydomain1.com nameserver = ns.mydomain1.com mail.mydomain1.com internet address = 192.168.1.1 ns.mydomain1.com internet address = 192.168.1.1 C:\>nslookup -type=a mail.mydomain1.com Server: router.lan Address: 192.168.1.100 *** No address (A) records available for mail.mydomain1.com This is a dig result: # dig +nocmd mydomain1.com any +multiline +noall +answer mydomain1.com. 86400 IN SOA ns.mydomain1.com. hostmaster.mydomain1.com. ( 121204007 ; serial 28800 ; refresh (8 hours) 7200 ; retry (2 hours) 604800 ; expire (1 week) 3600 ; minimum (1 hour) ) mydomain1.com. 86400 IN NS ns.mydomain1.com. mydomain1.com. 86400 IN A 192.168.1.1 mydomain1.com. 604800 IN MX 10 mail.mydomain1.com. mydomain1.com. 3600 IN TXT "v=spf1 include:mydomain1.com -all" When I try to ping: # ping mydomain1.com ping: cannot resolve mydomain1.com: Unknown host Is it a bug of dnsmasq 2.59? How to manage this problem?

    Read the article

  • Cannot Add Particular Word to Dictionary

    - by WCWedin
    I am trying to add a particular word to my custom dictionary using Word 2007. (The word happens to be "deserialized".) When I right-click on the word and click Add to Dictionary, the red underline does not go away. When I use the Spelling & Grammar tool from the Review tab on the ribbon, it will stop on that word; clicking the Add to Dictionary button has no effect. Oddly, I am able to add other words to the custom dictionary without a problem. I recently added "deserializes", for instance. I have only encountered this problem with that one particular word. Does anyone know what might be wrong and how I might fix it? Clarifications My document and all its content is set to English (United States). My custom dictionary is set to apply to All Languages, which is the default value. "Serialize" is in the US English default dictionary, but "deserialize" and its various forms is not.

    Read the article

  • Installing linux mint in one partition

    - by sha404
    So, I have a disk with a MBR setup(image below). I've managed to have 50 GB unallocated space for intalling Linux Mint 14. And I want to keep the current windows OS too(but don't want the Mint inside windows). Now I've seen in some tutorials that Linux Mint needs several partitions for bootloader, swap, & home. I don't like to have so many partitions & maybe MBR stuff won't let me create more than one now. So, is it possible to install Linux Mint in one partition only? If it is really impossible than what's the minimum number? & how can I accomplish that? Thanks in advance.

    Read the article

  • OpenVPN stopped working, what could have happened?

    - by jaja
    I have Openvpn, and it worked great when I used it on PC (Windows 8), then I copied all files (Certificates and config) to an Android 4 phone to use them. Now, Openvpn works on the phone, but not the PC. Specifically, when I open Google I get: The server at www.google.com can't be found, because the DNS lookup failed, but the VPN seems to be connected. I have a simple question, could the problem be because I copied the same files? Routing table before connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 =========================================================================== Routing table after connecting:- IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.254 192.168.1.101 25 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 **.**.***.** 255.255.255.255 192.168.1.254 192.168.1.101 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.101 281 192.168.1.101 255.255.255.255 On-link 192.168.1.101 281 192.168.1.255 255.255.255.255 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.101 281 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.101 281 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Server conf:- port 1194 proto udp dev tun ca ca.crt cert myservername.crt key myservername.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 push "redirect-gateway def1" Client conf:- client dev tun proto udp remote 89.32.148.35 1194 resolv-retry infinite nobind persist-key persist-tun mute-replay-warnings ca ca.crt cert client1.crt key client1.key verb 3 comp-lzo redirect-gateway def1 Here is the log file:- Tue Dec 18 16:34:27 2012 OpenVPN 2.2.2 Win32-MSVC++ [SSL] [LZO2] [PKCS11] built on Dec 15 2011 Tue Dec 18 16:34:27 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Tue Dec 18 16:34:27 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Dec 18 16:34:27 2012 LZO compression initialized Tue Dec 18 16:34:27 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue Dec 18 16:34:27 2012 Socket Buffers: R=[65536-65536] S=[65536-65536] Tue Dec 18 16:34:27 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue Dec 18 16:34:27 2012 Local Options hash (VER=V4): '41690919' Tue Dec 18 16:34:27 2012 Expected Remote Options hash (VER=V4): '530fdded' Tue Dec 18 16:34:27 2012 UDPv4 link local: [undef] Tue Dec 18 16:34:27 2012 UDPv4 link remote: ..*.:1194 Tue Dec 18 16:34:27 2012 TLS: Initial packet from ..*.:1194, sid=4d1496ad 2079a5fa Tue Dec 18 16:34:28 2012 VERIFY OK: depth=1, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:28 2012 VERIFY OK: depth=0, /C=/ST=/L=/O=/OU=/CN=/name=/emailAddress= Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue Dec 18 16:34:29 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Dec 18 16:34:29 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue Dec 18 16:34:29 2012 [myservername] Peer Connection Initiated with ..*.:1194 Tue Dec 18 16:34:32 2012 SENT CONTROL [myservername]: 'PUSH_REQUEST' (status=1) Tue Dec 18 16:34:32 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 10.8.0.1,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: timers and/or timeouts modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: --ifconfig/up options modified Tue Dec 18 16:34:32 2012 OPTIONS IMPORT: route options modified Tue Dec 18 16:34:32 2012 ROUTE default_gateway=192.168.1.254 Tue Dec 18 16:34:32 2012 TAP-WIN32 device [Local Area Connection] opened: \.\Global{F0CFEBBF-9B1B-4CFB-8A82-027330974C30}.tap Tue Dec 18 16:34:32 2012 TAP-Win32 Driver Version 9.9 Tue Dec 18 16:34:32 2012 TAP-Win32 MTU=1500 Tue Dec 18 16:34:32 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.8.0.6/255.255.255.252 on interface {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} [DHCP-serv: 10.8.0.5, lease-time: 31536000] Tue Dec 18 16:34:32 2012 Successful ARP Flush on interface [26] {F0CFEBBF-9B1B-4CFB-8A82-027330974C30} Tue Dec 18 16:34:37 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD ..*. MASK 255.255.255.255 192.168.1.254 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 C:\WINDOWS\system32\route.exe ADD 10.8.0.1 MASK 255.255.255.255 10.8.0.5 Tue Dec 18 16:34:37 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Tue Dec 18 16:34:37 2012 Route addition via IPAPI succeeded [adaptive] Tue Dec 18 16:34:37 2012 Initialization Sequence Completed

    Read the article

  • Join mp4 files in linux

    - by Jose Armando
    I want to join two mp4 files to create a single one. The video streams are encoded in h264 and the audio in aac. I can not re-encode the videos to another format due to computational reasons. Also, I cannot use any gui programs, all processing must be performed with linux command line utilities. FFmpeg cannot do this for mpeg4 files so instead I used MP4Box e.g. MP4Box -add video1.mp4 -cat video2.mp4 newvideo.mp4 unfortunately the audio gets all mixed up. I thought that the problem was that the audio was in aac so I transcoded it in mp3 and used again MP4Box. In this case the audio is fine for the first half of newvideo.mp4 (corresponding to video1.mp4) but then their is no audio and I cannot navigate in the video also. My next thought was that the audio and video streams had some small discrepancies in their lengths that I should fix. So for each input video I splitted the video and audio streams and then joined them with the -shortest option in ffmpeg. thus for the first video I ran avconv -y -i video1.mp4 -c copy -map 0:0 videostream1.mp4 avconv -y -i video1.mp4 -c copy -map 0:1 audiostream1.m4a avconv -y -i videostream1.mp4 -i audiostream1.m4a -c copy -shortest video1_aligned.mp4 similarly for the second video and then used MP4Box as previously. Unfortunately this didn't work either. The only success I had was when I joined the video streams separetely (i.e. videostream1.mp4 and videostream2.mp4) and the audio streams (i.e. audiostream1.m4a and audiostream2.m4a) and then joined the video and audio in a final file. However, the synchronization is lost for the second half of the video. Concretelly, there is a 1 sec delay of audio and video. Any suggestions are really welcome.

    Read the article

  • Cannot read/write a second drive in MBP 13

    - by Carlos
    I changed my original HDD for a SDD earlier this year and I just got one more SSD for my MBP 13 (2012) that I used to replace DVD drive. I'm using Mountain Lion. The SSD looks to be recognized allright, but I can't format it. Then I removed the main drive and tried the new one as the main drive and did the boot using a USB drive with MAC OS and everyhing worked as it should (like I just had one drive). However when I bring the first drive back together with the second they both show up but I can't use it. Seems like I have no permission, but when I look at it's properties it says I can read and write to it. Any ideas? Thanks a lot!

    Read the article

  • Booting off windows image through network

    - by Mr. Sir King Osman
    I have a HP st5742, which is a tower that does not have a hard drive and I am trying to boot it off the network, preferably off an image. It was designed along with the program HP Image Manager, however this program has been discontinued by HP and I can not seem to find a way to get a copy. If this helps, I am running my network with windows server 2008 R2 and would like the streaming client to be running windows. I have spent days searching for a way to deploy this machine however I can not seem to find a straight forward program, guide, or way to do this. I am new to this sort of thing but I willing to reading into the subject, all I need is a point in the right direction. Any help would be greatly appreciated.

    Read the article

  • How can I uninstall AppFabric?

    - by downatone
    I recently upgraded from Win 7 - Win 8. AppFabric was not one of the programs that came up as being incompatible when I ran the upgrade wizard, so I did not uninstall it. Now whenever I goto "Add or remove features" I get the following error: --------------------------- Windows Server AppFabric Setup Wizard --------------------------- Windows Server AppFabric is not supported on current operating system Windows 8 Pro(version 6.2.9200.0). Please refer to installation guide for the list of supported operating systems. --------------------------- OK --------------------------- Unfortunately the only way to uninstall AppFabric is via the "Add or remove features" - does anyone know a commandline command to kick the uninstall so I can at least access "Add or remove features"? Edit: C:\Windows\System32\AppFabric\Setup.exe /remove Throws the same error as above.

    Read the article

  • Analyse frequencies of date ranges in Google Spreadsheet

    - by wnstnsmth
    I have a Google Spreadsheet where I would like to compute occurrences of date ranges. As you can see in my sheet, there is a column date_utc+1 which contains almost random date data. What I would like to do is put the date values into bins of 6 hours each, i.e., 12/5/2012 23:57:04 until 12/6/2012 0:03:17 would be in the first bin, 12/6/2012 11:20:53 until 12/6/2012 17:17:07 in the second bin, and so forth. Then, I would like to count the occurrence of those bins, such as bin_from bin_to freq ----------------------------------------------- 12/5/2012 23:57:04 12/6/2012 0:03:17 2 12/6/2012 11:20:53 12/6/2012 17:17:07 19 ... ... ... Hope it is clear what I mean. Partial hints are very welcome as well since I am pretty new to spreadsheeting.

    Read the article

  • How to type a small fraction in Word 2007 equation editor?

    - by Timwi
    In Word 2007’s equation editor, I can enter “1/2” and I will get a properly formatted fraction. However, there is another kind of fraction that uses a smaller font size. How do I type that one using the keyboard alone? I notice that if I switch to linear mode, I get a small box displayed: Using the clipboard, I find that this is the same box (U+25A1) that I also get if I type “\box”. Despite, typing “\box(1/2)” still turns into a normal-size fraction and not the small fraction. How do I type the small fraction?

    Read the article

  • How to add Sharepoint Powershell to Console2

    - by BGM
    Salvete! I want to add the Powershell Console for Sharepoint to the tablist in Console2. I already have plain Powershell, but I want the Sharepoint Powershell snapin added automatically. If I look at the properties of the Sharepoint Powershell Console shortcut, I see this: C:\Windows\System32\WindowsPowerShell\v1.0\PowerShell.exe -NoExit " & ' C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\\sharepoint.ps1 ' " but that doesn't work in Console2, so I tried this, which doesn't work either: C:\WINDOWS\system32\windowspowershell\v1.0\powershell.exe -PSConsoleFile "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\psconsole.psc1" -NoExit " & ' C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\\sharepoint.ps1 ' " Whenever I try, it will load Powershell, but not the Sharepoint Console. I get this: Add-PSSnapin : The Windows PowerShell snap-in 'Microsoft.SharePoint.PowerShell' is not installed on this machine. At C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\SharePoint.ps1:3 char:13 + Add-PsSnapin <<<< Microsoft.SharePoint.PowerShell + CategoryInfo : InvalidArgument: (Microsoft.SharePoint.PowerShell:String) [Add-PSSnapin], PSArgumentException + FullyQualifiedErrorId : AddPSSnapInRead,Microsoft.PowerShell.Commands.AddPSSnapinCommand I tried this out, too. Anybody know?

    Read the article

  • Force Installing a Radeon HD 2100 on Windows 8

    - by Click Ok
    I'm trying force installing a Radeon HD 2100 on Windows 8. I've found that link from AMD with the drivers for Windows7: http://support.amd.com/us/gpudownload/windows/legacy/Pages/legacy-radeonaiw-vista64.aspx I know too that AMD will stop support Radeon HD 400 and older: http://www.techspot.com/news/48321-amd-drops-windows-8-support-for-radeon-hd-4000-and-older.html Now, let's go to the problem. If I try install the 12.6 driver, Windows will stick with the "basic display adapter", and this is bad for 3d games like Minecraft, that runs really slow now compared with the previous Windows7 installation. Forcing install the catalyst driver can help to fix it. So, I follow that steps: Extract the Catalist Driver (C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql) Right click the "basic display adapter" on device manager, and "update driver" Search on PC I will choose the driver "With Disk" "C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql\Packages\Drivers\Display\W76A_INF" There is a big list of drivers and the nearest driver to HD 2100 is "Radeon HD 2350 Series" My questions: Why isn't "Radeon HD 2100 Series" listed? (or Where is it listed?) In theory it must be listed" The first link above show that "This article applies to the following configuration(s):" (...) "AMD Radeon HD 2000 Series" Am I doing something wrong?

    Read the article

  • Vim - dynamic list of open buffers in a window

    - by asfallows
    I've investigated a few ways to maintain a list of open buffers in Vim, and some of them are very good, but none of them seem to behave the way I'd like. It's very possible that nothing like what I want exists, and it can't hurt to ask. I've been using NERDTree in GVim, and I like the idea of putting the information in a slender left-hand window. I've put together a handy diagram for how I'd like my environment to look: |--------|---------------------------------------| | | | | | | |NERDTree| Windows | | | | | | | | | | |--------| | | | | | | | | List | | | of | | | Open | | | Buffers| | | | | | | | |--------|---------------------------------------| So my question is: Is there a vim-native or plugin-enabled way to maintain a list of currently open buffers and select/edit/close from that list, inside a window similar to NERDTree? I understand that this approach may be incongruous with the Vim way of doing things, and if you feel like I'm missing something about how to manage multiple files in a Vim session, please leave a comment with suggestions!

    Read the article

  • Cannot logon guest account in windows 7

    - by Javy
    I'm using Windows 7 Home edition. When I try to create any guest account, it fails to load at login with the error: "The User Profile Service failed the logon. User profile cannot be loaded” I can login as admin and my home user with no problems. Every guest account that I create fails. I found this on a microsoft text article: This error may occur if the "Do not logon users with temporary profiles" Group Policy setting is configured. I've tried to find the Group Policy settings and cannot locate it anywhere. Some sites indicate I need to upgrade windows to access it. Is there a way to use guest accounts without upgrading?

    Read the article

  • How do I set up a working GUEST USER account in Win XP Pro?

    - by user6501
    I have two user accounts within my WinXP Pro PC. One I'd like to erase. But I'd also like to setup a GUEST user account. I've already gotten 2-step instructions on how to get rid of the extraneous account: a) use an MS tool called delprof.msi b) manually delete the former users files in Documents & Settings. But I guess my original question was too complex -- kind of like a bill in Congress. So now I am just asking the final part of the question: How do I create a GUEST ACCOUNT -- then define what it will authorize/grant access to? i.e. internet browser(s), specific programs and files etc

    Read the article

  • Custom Silent HTPC Uses Entire Case as a Heatsink

    - by Jason Fitzpatrick
    This silent media center PC dissipates heat in a rather clever way; the entire back of the case is one giant heatsink. Courtesy of computer enthusiast and tinker DeFex, the build isn’t just silent but quite eye catching too. He used a combination of one massive heatsink, custom brackets, acrylic, and bicycle spokes to create a sleek case that looks as much like a computer-inspired work of art as it does a media center computer. Hit up the link below to check out the build gallery and see how he mated the CPU to the heatsink-body with a custom milled aluminum bridge. Heatsink HTPC [via Hack A Day] Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

    Read the article

  • Google60 Emulates Search Engine Querying with 1960s Technology

    - by Jason Fitzpatrick
    Google60 is a novel little project that mimics the interface of a 1960s-era computer and mashes it up with modern Google search queries. Take it for a spin; you’ll never appreciate the speed of even the slowest modern browser more. While playing with the actual project is enjoyable, make sure to check out the project notes below the interface for an interesting look at design choices and emulating an old machine. Google60 [via Unpluggd] Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

    Read the article

  • How to Power Cycle Your Gadgets To Fix Freezes and Other Problems

    - by Chris Hoffman
    Have you ever had a smartphone, laptop, tablet, or any other electronic gadget become unresponsive? The surefire way to recover from the freeze – assuming it’s not a hardware problem – is by power-cycling the gadget. Most geeks know that pulling and reinserting a device’s battery will force it to recover from a freeze and boot right back up, but what if the device doesn’t have a removable battery? Image Credit: Alan Levine on Flickr Secure Yourself by Using Two-Step Verification on These 16 Web Services How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot

    Read the article

  • « Des alternatives open-sources matures existent sur tous les sujets d'entreprise », entretien autour du Guide de l'Open-Source

    « Des alternatives open-sources matures existent sur tous les sujets de l'entreprise » Entretien avec Grégory Bécue, auteur de la deuxième édition du Guide de l'open-source de Smile A l'occasion de la sortie de la deuxième édition du Guide de l'Open-Source, le Livre Blanc gratuit de référence de Smile, Developpez s'est entretenu avec le responsable de cette publication, Grégory Bécue. Nous avons abordé les motivations d'un tel guide, son intérêt pour les professionnels, ce qu'on y trouve concrètement, son histoire et ses nouveautés. Developpez.com : pourquoi faire un guide de l'open-source ? C...

    Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >