Search Results

Search found 6 results on 1 pages for 'coleifer'.

Page 1/1 | 1 

• OpenVPN not sending traffic to internet?

  - by coleifer

  I've set up openvpn on my pi and am running into a small issue. I can connect to the VPN server and ping it just fine, and I can also connect to other machines on my local network. However I am unable, when connected to the VPN, to reach the outside world (either by name lookup or IP). here are the details: On the server the tun0 interface: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.1 netmask 255.255.255.255 destination 10.8.0.2 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 I can ping it just fine: # ping -c 3 10.8.0.1 PING 10.8.0.1 (10.8.0.1) 56(84) bytes of data. 64 bytes from 10.8.0.1: icmp_seq=1 ttl=64 time=0.159 ms 64 bytes from 10.8.0.1: icmp_seq=2 ttl=64 time=0.155 ms 64 bytes from 10.8.0.1: icmp_seq=3 ttl=64 time=0.156 ms --- 10.8.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2002ms Routing table # ip route show default via 192.168.1.1 dev eth0 metric 204 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.6 metric 204 I also have ip traffic forwarding: net.ipv4.ip_forward = 1 I do not have any custom iptables rules (that I'm aware of). On the client, I can connect to the VPN. Here is my tun0: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.6 netmask 255.255.255.255 destination 10.8.0.5 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 21 bytes 1527 (1.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 And on the client I can ping it: sudo ping -c 3 10.8.0.6 PING 10.8.0.6 (10.8.0.6) 56(84) bytes of data. 64 bytes from 10.8.0.6: icmp_seq=1 ttl=64 time=0.035 ms 64 bytes from 10.8.0.6: icmp_seq=2 ttl=64 time=0.026 ms 64 bytes from 10.8.0.6: icmp_seq=3 ttl=64 time=0.032 ms --- 10.8.0.6 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1998ms rtt min/avg/max/mdev = 0.026/0.031/0.035/0.003 ms I can ssh from the client into another server on my LAN (192.168.1.x), however I cannot reach anything outside my LAN. Here's some of the server logs at the bottom of this gist: https://gist.github.com/coleifer/6ef95c3008f130249933/edit I am frankly out of ideas! I don't think it's my client because both my laptop and my phone (which has an openvpn client) exhibit the same behavior. I had OpenVPN installed on this pi before using debian and it worked, so I don't think it's my router but of course anything is possible.

  Read the article

• How would one build a relational database on a key-value store, a-la Berkeley DB's SQL interface?

  - by coleifer

  I've been checking out Berkeley DB and was impressed to find that it supported a SQL interface that is "nearly identical" to SQLite. http://docs.oracle.com/cd/E17076_02/html/bdb-sql/dbsqlbasics.html#identicalusage I'm very curious, at a high-level, how this kind of interface might have been architected. For instance: since values are "transparent", how do you efficiently query and sort by value how are limits and offsets performed efficiently on large result sets how would the keys be structured and serialized for good average-case performance

  Read the article

• scp stalls and ssh sessions freeze up (but eventually start again)

  - by coleifer

  I am running ubuntu on various computers on a home network. Some are on 9.04x64, some 10.04x64 and one 9.04x32. Running scp with a large file starts out at 2.1 mbps and drops down to about 200k, stalling and dropping until the transfer is complete. I've noticed this when I have a secure shell open on any of these servers as well. I have tried this with 2 different routers, both brand new, different brands.

  Read the article

• scp stalls and ssh sessions freeze up (but eventually start again)

  - by coleifer

  I am running ubuntu on various computers on a home wireless network. Some are on 9.04x64, some 10.04x64 and one 9.04x32. Running scp with a large file starts out at 2.1 mbps and drops down to about 200k, stalling and dropping until the transfer is complete. I've noticed this when I have a secure shell open on any of these servers as well. I have tried this with 2 different routers, both brand new, different brands.

  Read the article

• Multicore solr on Ubuntu 10.04 working for anyone?

  - by coleifer

  Following instructions from the two sites below, I've installed tomcat6 and solr 1.4 http://gist.github.com/204638 https://wiki.fourkitchens.com/display/TECH/Solr+1.4+on+Ubuntu+9.10+and+CentOS+5 I have successfully got it up and running on a server running 9.04 with multicore support, but on the 10.04 I can't seem to get it to work. I am able to reach localhost:xxxx/solr/ on the 10.04 box and see a single link to the Solr Admin, but following the link takes me to a 404 page with the following output: /solr/admin/ HTTP Status 404 - missing core name in path The requested resource (missing core name in path) is not available I am also unable to access /solr/site1/ as I would except - it similarly returns a 404 <!-- from /var/solr/solr.xml, site dirs exist --> <cores adminPath="/admin/cores"> <core name="site1" instanceDir="site1" /> <core name="site2" instanceDir="site2" /> </cores> <!-- from /etc/tomcat6/Catalina/localhost/solr.xml --> <Context docBase="/var/solr/solr.war" debug="0" privileged="true" allowLinking="true" crossContext="true"> <Environment name="solr/home" type="java.lang.String" value="/var/solr" override="true" /> </Context>

  Read the article

• How do I fix this installation problem with multicore Solr on Ubuntu 10.04?

  - by coleifer

  Following instructions from the two sites below, I've installed Tomcat 6 and Solr 1.4. http://gist.github.com/204638 https://wiki.fourkitchens.com/display/TECH/Solr+1.4+on+Ubuntu+9.10+and+CentOS+5 I have successfully got it up and running on a server running 9.04 with multicore support, but on the 10.04 I can't seem to get it to work. I am able to reach localhost:xxxx/solr/ on the 10.04 box and see a single link to the Solr Admin, but following the link takes me to a 404 page with the following output: /solr/admin/ HTTP Status 404 - missing core name in path The requested resource (missing core name in path) is not available I am also unable to access /solr/site1/ as I would except - it similarly returns a 404. <!-- from /var/solr/solr.xml, site dirs exist --> <cores adminPath="/admin/cores"> <core name="site1" instanceDir="site1" /> <core name="site2" instanceDir="site2" /> </cores> <!-- from /etc/tomcat6/Catalina/localhost/solr.xml --> <Context docBase="/var/solr/solr.war" debug="0" privileged="true" allowLinking="true" crossContext="true"> <Environment name="solr/home" type="java.lang.String" value="/var/solr" override="true" /> </Context>

  Read the article

1