Search Results

Search found 4 results on 1 pages for 'mstaessen'.

Page 1/1 | 1 

• Cannot sleep/standby in Ubuntu 12.04

  - by mstaessen

  Yesterday, I installed Ubuntu 12.04 Desktop i386 on my netbook (HP Mini 311c). I am unable to use the sleep mode. When I press the suspend button (or do sudo pm-suspend), the screen flickers but the computer does not power off. Even worse, the screen comes back up and I'm back where I left off. Hibernating does work (although it is not available in Power Management). I have to use pm-hibernate to make that work. I'm using the 3.2.0.20 kernel and Gnome 3.3.92 (Unity, especially compiz, is a resource hog). Before Ubuntu 12.04, I was using Mint Linux 12 with the 3.0 kernel and everything worked fine back then. Any help is much appreciated because this is driving me crazy.

  Read the article

• What would you take into account when you were asked to compare software? [closed]

  - by mstaessen

  For my master's thesis, I am asked to make a comparative study of frameworks for cross-platform mobile development. I want to eliminate the chances of having missed something in my comparison. This is why I want to ask what YOU would value (most) when comparing such frameworks (Like for instance PhoneGap and Appcelerator Titanium). Performance, capabilities and licensing are kind of obvious, but can you think of others?

  Read the article

• Multiple VLANs on a single subnet

  - by mstaessen

  I would like to establish the setup shown below. The image is taken from (http://gcharriere.com/blog/?p=620) and explains how to set this up on a brocade device. I would like to use an ubuntu server to do the routing. Right now, the switch and the server/router are connected with a trunk and the server uses the vlan package, kernel module and (inner) subnets for routing. I would like that: no IP addresses get lost in the subnetting (outer subnet is /26, inner subnets are /28) I don't want the rigorous subdivision of my outer subnet. I want to assign a VLAN to any IP in the outer subnet. How do I need to configure my interfaces? What is the "ubuntu" translation of "ip follow ve"? Thanks!

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

1