Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 101/1617 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

  • m not able to connect to wifi network

    - by Broken Heart
    i had tried every code every idea every thing but i failed wiireless driver broadcom bcm43412 but when i checked pci-id it show not supported my pci id is 14e4:4365 and chip id is BCM43142 i tried edit connection myself to olso but i cannt wat to put in clone mac adress place? device mac adress is the router mac adress but what is clone mac adress i had placed my laptop mac adress in place of clone mac adress bt it doesnot work tried every thing but it not work checked additional driver by going system settings it doesnot contain any drivers,tried internet by cable then it connects then how sholud i correct this plz tell

    Read the article

  • How do I find out which process is eating up my bandwidth?

    - by Bruce Connor
    I think I'm being the victim of a bug here. Sometimes while I'm working (I still don't know why), my network traffic goes up to 200 KB/s and stays that way, even tough I'm not doing anything internet-related. This sometimes happens to me with the CPU usage. When it does, I just run a top command to find out which process is responsible and then kill it. Problem is: I have no way of knowing which process is responsible for my high network usage. Both the resource monitor and the top command only tell me my total network usage, neither of them tells me process specific network info. Is there another command I can use to find out which process is getting out of hand? I've already tried killing all the obvious ones (firefox, update-manager, pidgin, etc) with no luck. So far, restarting the machine is the only way I found of getting rid of the issue. EDIT: (just to be clear) I've found questions here about monitoring total bandwidth usage, but, as I mentioned, that's not what I need. UPDATE: The command iftop gives results that disagree entirely with the information reported by System Monitor. While the latter claims there's high network traffic, the former claims there's barely 1 KB/s. Thanks

    Read the article

  • Sharing SCTP connection with multiple threads

    - by poly
    I have an application that needs to run in SCTP environment, I have a question in sharing the connection among multiple threads for packet receiving only, I've tried with the sctp_sendmsg and it worked without even locking the threads (is that been taking care of by the OS, in other words, is it thread safe to do that). I've tested many cases with the send and I can't see them out of sync. Anyway, back to the receiving, is it possible to create multiple threads and send each thread the sctp descriptor to start receiving messages? Do I need a lock here or is it ok without lock? I'm using C in linux.

    Read the article

  • How to properly do weapon cool-down reload timer in multi-player laggy environment?

    - by John Murdoch
    I want to handle weapon cool-down timers in a fair and predictable way on both client on server. Situation: Multiple clients connected to server, which is doing hit detection / physics Clients have different latency for their connections to server ranging from 50ms to 500ms. They want to shoot weapons with fairly long reload/cool-down times (assume exactly 10 seconds) It is important that they get to shoot these weapons close to the cool-down time, as if some clients manage to shoot sooner than others (either because they are "early" or the others are "late") they gain a significant advantage. I need to show time remaining for reload on player's screen Clients can have clocks which are flat-out wrong (bad timezones, etc.) What I'm currently doing to deal with latency: Client collects server side state in a history, tagged with server timestamps Client assesses his time difference with server time: behindServerTimeNs = (behindServerTimeNs + (System.nanoTime() - receivedState.getServerTimeNs())) / 2 Client renders all state received from server 200 ms behind from his current time, adjusted by what he believes his time difference with server time is (whether due to wrong clocks, or lag). If he has server states on both sides of that calculated time, he (mostly LERP) interpolates between them, if not then he (LERP) extrapolates. No other client-side prediction of movement, e.g., to make his vehicle seem more responsive is done so far, but maybe will be added later So how do I properly add weapon reload timers? My first idea would be for the server to send each player the time when his reload will be done with each world state update, the client then adjusts it for the clock difference and thus can estimate when the reload will be finished in client-time (perhaps considering also for latency that the shoot message from client to server will take as well?), and if the user mashes the "shoot" button after (or perhaps even slightly before?) that time, send the shoot event. The server would get the shoot event and consider the time shot was made as the server time when it was received. It would then discard it if it is nowhere near reload time, execute it immediately if it is past reload time, and hold it for a few physics cycles until reload is done in case if it was received a bit early. It does all seem a bit convoluted, and I'm wondering whether it will work (e.g., whether it won't be the case that players with lower ping get better reload rates), and whether there are more elegant solutions to this problem.

    Read the article

  • Remote connection problem.

    - by Woody
    Hello I have ubuntu 10.04 installed with mysql on it and I have a problem with remote connection. When I connect through putty it works but sometimes it looks like it hangs for example when I execute the command ln --help. Also with MySQL connection When I execute a simple query like show processlist; it works, but for example select * from table not always, if the table doesn't have many rows it works but if it has let's say more than 20 the query looks like it keeps working and never ends. It's connected but I can't do many things remotely. Added: I connect using putty from other windows pc, server is not overloaded. when i work at the same time directly on ubuntu i can do everything. Remotely not.

    Read the article

  • Any good web frameworks for asynchronous multiplayer games?

    - by Steven Stadnicki
    I'm trying to craft a site for web-based (original) board games, and my client (currently written in Actionscript, but that's highly fungible) works fine - I can play solitaire games in the client - but it has nothing to connect to. What I'm looking for is a server framework for handling accounts/authentication and game tracking: something that would let players log in, show them a list of their current games, let them invite friends to new games, let them make moves in the games they have open, etc. I'm flexible on language; obviously I'm going to have to write a lot of server code to handle the actual game logic, but that should be straightforward enough. I'm more concerned with how to handle the user (and game) DBs, though suggestions for a good server framework for communicating with the DBs (and serving up, most likely, JSON for client communications) are also welcome. Right now my leaning is towards Ruby (probably with Rails) but as far as I can determine it would be a pretty good chunk of effort to set up the necessary databases, so having something even higher-level would be really useful to me.

    Read the article

  • How can I prioritize wireless networks with network-manager

    - by kynan
    Mostly I use my laptop in an environment where different wireless networks are available and I would like to preferably connect to one of those and only fall back to the other one if that one is not available. Is there any way of prioritizing which wireless networks network-manager preferably connects to? The only workaround I found so far was unchecking Connect Automatically in the options and re-enabling it when my preferred network is not available.

    Read the article

  • How to install Netgear N-300 UAB adapter WNA3100 on Ubuntu 12.04

    - by JacobusR
    After a fresh install of Ubuntu 12.04, the first thing I'm trying to do, is to setup my wireless adapter. I can see it using lsusb: beer@beer-linux:~$ lsusb ... Bus 002 Device 006: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] ... I have found a lot of dated instructions on the net and just wanted to know what the right way is to set it up on 12.04. I don't want to mess up a brand new install by tweaking things that don't need tweaking. According to most posts, you have to install the Windows drivers using the ndiswrapper package. Is this still the right way to go? If so, it would be great if someone could write down the steps to do this under 12.04

    Read the article

  • 1000baseT/Full Supported and Advertised but not working!

    - by user11973
    Hello, i'm using a AT3IONT-I motherboard with integrated card. If I ethtool it to 1000 full duplex it wont work! Here is sudo ethtool eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) Link detected: yes here is sudo lshw -C network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 03 serial: bc:ae:c5:8b:7d:33 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.021.00-NAPI duplex=full ip=192.168.0.2 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:42 ioport:e800(size=256) memory:f8fff000-f8ffffff memory:f8ff8000-f8ffbfff memory:fbff0000-fbffffff And lspci -nn: 00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1) 00:00.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a88] (rev b1) 00:03.0 ISA bridge [0601]: nVidia Corporation MCP79 LPC Bridge [10de:0aad] (rev b3) 00:03.1 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0aa4] (rev b1) 00:03.2 SMBus [0c05]: nVidia Corporation MCP79 SMBus [10de:0aa2] (rev b1) 00:03.3 RAM memory [0500]: nVidia Corporation MCP79 Memory Controller [10de:0a89] (rev b1) 00:03.5 Co-processor [0b40]: nVidia Corporation MCP79 Co-processor [10de:0aa3] (rev b1) 00:04.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa5] (rev b1) 00:04.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa6] (rev b1) 00:06.0 USB Controller [0c03]: nVidia Corporation MCP79 OHCI USB 1.1 Controller [10de:0aa7] (rev b1) 00:06.1 USB Controller [0c03]: nVidia Corporation MCP79 EHCI USB 2.0 Controller [10de:0aa9] (rev b1) 00:08.0 Audio device [0403]: nVidia Corporation MCP79 High Definition Audio [10de:0ac0] (rev b1) 00:09.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Bridge [10de:0aab] (rev b1) 00:0b.0 RAID bus controller [0104]: nVidia Corporation MCP79 RAID Controller [10de:0abc] (rev b1) 00:0c.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac4] (rev b1) 00:10.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0aa0] (rev b1) 00:15.0 PCI bridge [0604]: nVidia Corporation MCP79 PCI Express Bridge [10de:0ac6] (rev b1) 03:00.0 VGA compatible controller [0300]: nVidia Corporation ION VGA [10de:087d] (rev b1) 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) If i use Code: sudo ethtool -s eth0 speed 1000 duplex full autoneg off then in ethtool speed is Unknown and it doesn't work; if I set it via pre-up it wont work either... Please help!! Thanks!

    Read the article

  • Which game logic should run when doing prediction for PNP state updates

    - by spaceOwl
    We are writing a multiplayer game, where each game client (player) is responsible for sending state updates regarding its "owned" objects to other players. Each message that arrives to other (remote) clients is processed as such: Figure out when the message was sent. Create a diff between NOW and that time. Run game specific logic to bring the received state to "current" time. I am wondering which sort of logic should execute as part of step #3 ? Our game is composed of a physical update (position, speed, acceleration, etc) and many other components that can update an object's state and occur regularly (locally). There's a trade off here - Getting the new state quickly or remaining "faithful" to the true state representation and executing the whole thing to predict the "true" state when receiving state updates from remote clients. Which one is recommended to be used? and why?

    Read the article

  • Help setting up wireless in Ubuntu 13.04

    - by James
    I'm having problems connecting my WIFI in Ubuntu 13.04 . So I was wondering if filling in the data manually ie: the IPv4, IPv6, the SSID and BSSID info etc. I did try this before but maybe I put in the wrong data or maybe not enough. Would that make it work? I just don't know how to find out some of the data you need to put in? I'm new and it's confusing. Does anyone know the solution? Here is lspci: james@james-MM061:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 01) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) 0b:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) Computer information: Model: Dell MM061 Mobile Intel(R) 945GM Express Chipset Family [Display adapter] (2x)

    Read the article

  • Connecting to VPN / proxy with different port number

    - by user779159
    I have an IP address, port, username, and password for one of those VPN / proxy services that allows you to use an IP address other than what your ISP gives you, but in the 'Edit Connections VPN' GUI I don't see where to enter a port. I enter the IP address under 'Gateway' and the username and password where it asks for it, but it doesn't work. I try to enter it with the IP address ending with a colon, followed by the port, but that doesn't work either (e.g. "1.1.1.1:9999"). Any idea how I could make it work? I'm using Ubuntu 12.04 LTS. Thanks.

    Read the article

  • How to restart WiFi interface without rebooting (it drops connection)?

    - by Dima
    I boot into ubuntu and it connects to the Wifi network fine. After about 10-15min the DNS stop resolving any website and a couple of minutes later network-managers tells me that I'm disconnected and tries to reconnect constantly to my router and fails to do it. Upon Ubuntu restart everything works fine for the first 10-15min again. When I boot into Mac OS X everything is fine with the same connection! How do I restart wifi interface? sudo ifdow wlan0 just tells me that wlan0 is not configured and wlan0 doesn't appear in /etc/network/interfaces either, which I find strange.... (unless network-manager is doing it behind my back).

    Read the article

  • 12.04 - why does the network icon dissapear every time my machine is turned off

    - by Howard Walker
    After spending an hour or two working out how to find the network Icon, I find that when I reboot the machine, I have to go through the whole procedure again. 1. The network menu is not there - so first I have to find the terminal. This has no particular location that I can find but usually I have to type terminal in the dash. 2. Then I have to type nm-applet in terminal 3. The network manager icon then appears, but only works if the terminal window remains open. Shut down the terminal window and the network disappears. This is a pain - plus I have to type my password in every time, which is another waste of time, thought this has always been a problem. So can anyone tell me how to make the web automatically connect at startup without any intervention from me.

    Read the article

  • Use two networks at the same time?

    - by Christopher
    I want to use Ubuntu 10.10 Server in a classroom, a computer lab whose bandwidth is provided by a local cable ISP. That's no problem, though the school network has an IP printer that I want to use. I cannot reach the printer through the cable Internet. But, I have two network cards. How is it possible to use both networks at once? eth0 (static 192.168.1.254) is plugged into a four-port router, 192.168.1.1. On the public side of the four-port router is Internet provided by the cable company. I also have the classroom workstations plugged into a switch. The switch is plugged into the four-port router. The whole classroom is wired into the cable Internet. The other NIC, eth1, could it be plugged into an Ethernet jack in the wall? It uses the school network, and I might receive by DHCP an IP address like 10.140.10.100, with the printer on maybe 10.120.50.10. I was thinking about installing the printer on the server so that it could be shared with the workstations. But how does this work? Can I just plug eth1 into the school network and access both LANs? Thanks for any insight

    Read the article

  • Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect

    - by user287529
    Ubuntu 12.04 host – Virtualbox 4.1.12 Guest=Windows 7 – Network will not connect. I'm using Ubuntu 12.04 on an Acer Aspire 5742-7645 laptop with 4GB memory, Intel Core i3 processor, Intel HD Graphics, DVD drive, 802.1 b/g/n, and 500 GB HD. I connect to my router via a wireless connection. I have installed Virutalbox 4.1.12 from the Ubuntu Software Center and installed Guest additions 4.1.12 in the Windows 7 guest session. I have Windows XP and Windows 7 installed as guests in Virtual box The network settings are different for XP and 7 – see below. Network Settings XP guest = Adapter 1: PCnet-FAST III (NAT) - Network works perfectly and has worked well for several years. Network Settings Win 7 = Adapter 1: Intel PRO/1000 MT Desktop (Bridged adapter, eth1) Promiscuous Mode = allow all Cable connected = checked When I originally installed Windows 7, I tried NAT and the guest network would not connect. Once I changed the setting to the above (Bridged) the Network worked perfectly. However, what I believe is after updates (not sure if it was an Ubuntu or Windows update) the guest network stopped working and I can not get it to connect. Interfaces file content auto lo iface lo inet loopback Ifconfig yields lou@lou-Aspire-5742:~$ ifconfig eth0 Link encap:Ethernet HWaddr 1c:75:08:09:f6:5c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 Link encap:Ethernet HWaddr 4c:0f:6e:7c:9f:01 inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4e0f:6eff:fe7c:9f01/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18095 errors:2 dropped:0 overruns:0 frame:24344 TX packets:9281 errors:47 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5301926 (5.3 MB) TX bytes:1441885 (1.4 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3208 errors:0 dropped:0 overruns:0 frame:0 TX packets:3208 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:294088 (294.0 KB) TX bytes:294088 (294.0 KB) Ipconfig yields the following: Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::38ba:dbca:a21d:c3d1%13 Autoconfiguration IPv4 Address. . : 169.254.195.209 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{B292E440-679D-4FC5-8E34-77D6804669C8}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : I'm not sure what else to do. Can someone provide the troubleshooting steps to determine what the problem is and possible solution?

    Read the article

  • How to direct Ubuntu to use USB connection for Internet

    - by t3ch
    Hi folks, I posted yesterday regarding how to configure easytether on Ubuntu. I followed the steps and everything looks good from the terminal. But I am not able to connect to the Internet. Currently I am connected to a Wireless network, I tried disconnecting to it, in hope to connect to Internet using my phone but with no help. How do I make my notebook use my cell phone's connection. I have attached the snapshot from the terminal.

    Read the article

  • A "tinkered" PC can ping by IP, not by hostname. How to fix?

    - by aitchnyu
    Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

    Read the article

  • No Wireless In Ubuntu 13.10 (maybe Need Wireless Driver) [duplicate]

    - by viktorhubinette
    This question already has an answer here: No Wireless In Ubuntu 13.10 2 answers hi after updating to ubuntu 13.10 i cant see the wireless networks on the network meny so what should i do ? tell me some commands you need to see to solve the problem. Thanks (i maybe need a wireless driver becouse i installed one when i haved 12.04 becouse i could not connect to wireless before too) i cant connect to wireless that my problem so what do i need to do to get this wireless working again? some outputs lsmod | grep rt1 nothing sudo modprobe rt18192cu FATAL: Module rt18192cu not found. iwconfig eth0 no wireless extensions. lo no wireless extensions. sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning. rfkill list all nothing

    Read the article

  • Procedural object generation and unique identification

    - by 2080
    My question relates to procedural content generation and data management of the emerging objects in a database. I assume a networked game, with a server-client model. Unspecified objects in the game world are generated while the game is running with procedural algorithms (for example perlin noise). The players (/clients) can modify the properties of these objects, but have to notify the server of these changes. How could this communication address unique objects, so that both the server and the client know of which object they are speaking? Not only the inner properties of the objects can differ, but also visible, such as the position. When the player wants to select one of these objects the game has to find out the id - does anyone know which methods or algorithms can accomplish that?

    Read the article

  • Modular Web App Network Architecture

    - by nairware
    Assuming that I am dealing with dedicated physical servers or VPSs, is it conceivable and does it make sense to have distinct servers setup with the following roles to host a web application? Reverse Proxy Web server Application server Database server Specific points of interest: I am confused how to even separate the web and application servers. My understanding was that such 3-tier architectures were feasible. It is unclear to me if the app server would reside directly between the web and database server, or if the web server could directly interact with the database as well. The app server could either do the computational heavy-lifting on behalf of the app server or it could do heavy-lifting plus control all of the business logic (as implied in the diagram above, thus denying the web server of direct database access). I am also unsure what role the reverse proxy (ex. nginx) could and should fulfill as a web server, given the above mentioned setup. I know that nginx has web server features. But I do not know if it makes sense to have the reverse proxy be its own VPS, given that the web server–in theory–would be separate from the app server.

    Read the article

  • Best way to handle realtime melee AI in authoritative network environment

    - by PrimeDerektive
    So i've been working on a multiplayer game for a bit; it's a co-op action RPG with real-time combat. If you've seen or played TERA, I'd say it's comparable to that, but not an MMO, heh. I'm currently handling the AI units authoritatively, the server calculates their pathing, movement, and pursue/attack logic, and syncs the movement to the clients 15x per second, and the state changes when they happen. When I emulate 200ms ping, though, the client can perceive being out of range to an AI's attack, but still take the hit, because on the server he hadn't moved that far yet. This also plays hell with my real-time blocking. I don't really want to allow the clients to be allowed to say "that was out of range" or "I blocked that", but I'm not really sure how else to handle it.

    Read the article

  • Use same dns server for all (future) connections

    - by kleofas
    I'm wondering if it is possible to specify, that all connections (even future, like when using wifi at some other place (=different SSID)) will be using pre-defined DNS server When I have some (concrete) connections, I could go to IPv4 settings, and specify DNS server there (however, in case of new connection I would have to do it (and not forget it)) This may be particularly useful for some safe/filtering dns (such as opendns's 208.67.222.123 & 208.67.220.123)

    Read the article

  • Problems with microphone and network

    - by AnoonymoouS
    Hello... very good day everybody! I'm having some problems regarding the Ubuntu 12.4.01 LTS. For this reason, cordially i ask everyone's help. Such problems can be summed up in network (01) and audio (02)! 01) I can not set a DSL network settings in the "upper bar" (on side the clock). When i create the connection, the system says that the cables modem are disconnected! I can only use the internet if i set up a connection at terminal through the command "pppoeconf". Follows the print screen of what i mentioned above:. http://i.imgur.com/8nTrF.png Obs.: Note that even after the connection "created", it does not appear there! 02) The sound is reproduced; however, can not be captured! I can not make recordings, obviously i can't use the microphone. I believe that something is giving interference or the settings are wrong! Follows the video of what i mentioned above:. http://dl.dropbox.com/u/41085750/Projeto%20Padr%C3%A3o.mp4 Obs.: I'm listening to music, so that interference errors may appear in the video. By kindness; who can help me... help me! I sought help at various sites and forums but unfortunately, i did not get success. I wait anxiously for a direction. Regards, Anoonymoous.

    Read the article

  • gnome-file-share-properties doesn't work

    - by Riccardo Magrini
    I've configured gnome-file-share-properties on all my Ubuntu's PC for sharing the directory Public to each other. I following some guide found on Internet for the configuration of it, all explain the same procedure but in my case I don't see any Public directory shared with the PC. Following this link http://library.gnome.org/users/gnome-user-share/stable/gnome-user-share-getting-started.html.en I'd see the directory Public plus the name of PC that shares its directory on Nautilus Places. In my case I don't see anything, therefore on the Network place see all the machines 'n if I try to click on one receive this: "DBus error org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus)" note: I don't want to use Samba because I've all Ubuntu PC, and the firewall is disabled on all PC.

    Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >