Search Results

Search found 7728 results on 310 pages for 'wifi driver'.

Page 101/310 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

  • Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

    - by Benjamin Maus
    I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

    Read the article

  • Mac OS X: pushing all traffic through a VMWare VM

    - by bj99
    I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

    Read the article

  • Where can I configure wireless to be passed on to the Virtualbox guest?

    - by huahsin68
    I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

    Read the article

  • Turn my machine in a hotspot/proxy

    - by Leonardo
    My workplace does not provide a wifi... only wired connection... but my machine has a working wifi card... is there a way to "bridge" my wired connection, making my iphone connect to it and use it as if the own machine is being used? (the idea is to make my machine provide a wifi-connection and route it through my wired connection) Details: My machine OS is win 2012 server I have full admin rights to my machine There is a corporate-proxy PS: If more details needed pls ask!

    Read the article

  • Why does Windows Firewall show "Unidentified network" as one of my "Active public networks"?

    - by MousePad
    I have a machine that has wifi and ethernet. I have wifi active, and am not using ethernet. My Windows firewall shows two active networks, one is the wifi network I connect to, and the other is "Unidentified network". What is this unidentified network? I can't seem to be able to get rid of it because I can't find where it is even defined. How can you detect this and know whether this is just something appropriate or possibly a security problem? I am on Windows 7 64bit.

    Read the article

  • Netgear genie says my Internet is off, while Windows claims I am connected

    - by Manu
    I'm connected via wifi to my ISP's router/modem. While Windows says that I'm always connected, I keep getting messages from Netgear Genie that I've lost contact to the Internet, and I cannot access webpages until it comes back. There are two other computers in the house, one connected to the router via ethernet, the other via wifi, both seem to have no such problems. I've wondered if Netgear genie itself was the problem, but I am regularly disconnected even if I uninstall it. And I'd rather have it since it accurently tells me if I'm connected or not. Why does windows says I'm online if I can't access any online game, or website ? Is "netgear genie" the problem ? I've removed the connection, recreated it, I've even copied the settings to a usb key from the computer that has wifi access.

    Read the article

  • Blocked port 25 on Windows 7 64 bit

    - by Michal Gow
    Strange problem. I have 2 computers connected to Wifi router. One with Windows Vista & second with 2 operating systems: SUSe Linux and Windows 7 64bit on it. Computer with Vista can connect to SMTP server of my email provider (and any other) using port 25, and can connect to a mail server using telnet mail.server.com 25 if this port is open. Computer with dual operating system can (using Linux) do the same. The same computer, with the same hardware (Wifi card etc.), and using the same WiFi router, cannot however use Port 25 and cannot Telnet into any smtp server. So the problem is in Windows 7. I did uninstall all antivirus software and disabled the firewall. The problem is still here. Is there way how find out which software is blocking this port?

    Read the article

  • Is visiting HTTPS websites on a public hotspot secure?

    - by Calmarius
    It's often said that HTTPS SSL/TLS connections are encrypted and said to be secure because the communication between the server and me is encrypted (also provides server authentication) so if someone sniffs my packets, they will need zillions of years to decrypt if using brute force in theory. Let's assume I'm on a public wifi and there is a malicious user on the same wifi who sniffs every packet. Now let's assume I'm trying to access my gmail account using this wifi. My browser does a SSL/TLS handshake with the server and gets the keys to use for encryption and decryption. If that malicious user sniffed all my incoming and outgoing packets. Can he calculate the same keys and read my encrypted traffic too or even send encrypted messages to the server in my name?

    Read the article

  • How to test Laptop NIC's throughput using a router and PC - without be bounded?

    - by 0x90
    My setup includes: Cisco router An i-7 PC running windows A laptop with high speed wifi nic, which I want to check its throughput. I would like to run an FTP server on the PC. hook the router over cables to the PC. I would like to have the PC create its own subnet accessible via the cisco router that would be hooked directly to the PC's nic. From the laptop I want to connect via wifi to the PC's wireless router and connect to the ftp server on the PC. is it possible? how do i connect the router to the PC nic and make it broadcast a subnet via wifi for my laptop to connect to? how do i configure an FTP server to operate only on this subnet?

    Read the article

  • Remote Desktop connection breaks the wireless connection

    - by Michal Talaga
    When I connect to my Windows 8 Professional machine via Remote Desktop (RDP) I almost always get my WiFi connection broken. The setup: T61P Lenovo Laptop + W8 at home Wireless Router with NAT forwards connections to that machine Windows 7 laptop at work connecting to the home laptop When I connect, very often I get to login and suddenly connection is lost and I cannot reconnect again. When I get home I find my WiFi connection is still connected to the Access Point but does not function. Can't even ping the router. What is strange is that disabling wireless with the hardware switch and enabling it again doesn't help. The only way to make it works again: - Reboot - Disable wifi with hardware switch AND disable the network card in Device Manager, then enable both I did not have this problem on the very same laptop when it was running Windows 7. Any hint how can I find where the problem is?

    Read the article

  • How do I connect my NetXtreme BCM5755M Gigabit Ethernet PCI Express in y Dell latitude d630?

    - by Stanton.Sculpture
    Trying to get my 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02) working with my wifi. I just installed Raring Ringtail on this dell latitude D630 and I can't get it to connect without a wifi dongle. This is what I got when I typed sudo lshw -c network: *-network description: Ethernet interface product: NetXtreme BCM5755M Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 02 serial: 00:21:70:98:04:32 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 firmware=5755m-v3.29 latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:fe8f0000-fe8fffff *-network description: Wireless interface physical id: 2 bus info: usb@2:1 logical name: wlan0 serial: 7c:dd:90:11:a0:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.8.0-31-generic firmware=0.29 ip=10.0.0.8 link=yes multicast=yes wireless=IEEE 802.11bgn Also, when I go to additional drivers in the software and updates settings, no proprietary drivers show up. I've tried sudo apt-get install b43-fwcutter firmware-b43-installer because it worked on a bunch of old Dell laptops that I converted over before, but it didn't work on this one. Is this driver even compatible with wifi? Please help.

    Read the article

  • can't access SAMBA shares on UBUNTU-server from other computers

    - by larand
    Installed UBUNTU-server 12.04 and configured /etc/samba/smb.conf as: #======================= Global Settings ======================= [global] workgroup = HEMMA server string = %h server (Samba, Ubuntu) security = user wins support = yes dns proxy = no log file = /var/log/samba/log.%m max log size = 1000 syslog = 0 panic action = /usr/share/samba/panic-action %d encrypt passwords = no passdb backend = tdbsam obey pam restrictions = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes map to guest = bad user ############ Misc ############ usershare allow guests = yes #======================= Share Definitions ======================= [printers] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = yes create mask = 0700 # Windows clients look for this share name as a source of downloadable # printer drivers [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = no [Bilder original] comment = Original bilder path = /mnt/bilder/org browseable = yes read only = no guest ok = no create mask = 0755 [Bilder publika] comment = Bilder för allmän visning path = /mnt/bilder/public browseable = yes read only = yes guest ok = yes [Musik] comment = Musik path = /mnt/music/public browseable = yes read only = yes guest ok = yes I have a network setup around a 4G router "HUAWEI B593" where some computers are connected by WIFI and others by LAN. The server is connected by LAN. On one computer running windows XP I can see the server but are not allowed to acces them. On another computer on the WIFI-net running win7 I cannot see the server at all but I can ping the server and I can see the smb-protocoll is running when sniffing with wireshark. I don't primarily want to use passwords, computers on the lan and wifi should be able to connect without any login-procedure. I'm sure my config is not sufficient but have hard to understand how I should do. Theres a lot of descriptions on the net but most is old and none have been of any help. I'm also confused by the fact that I can not se the sever on my win7-machine even though it communicates with the samba-server. Would be very happy if anyone could spread some light over this mess.

    Read the article

  • Dell Laptop's Bluetooth isn't detected by Ubuntu

    - by vishwaje
    I have Dell vostro 3500 Laptop. I Installed Ubuntu 12.04. It doesn't detect my bluetooth. below is my information. lsusb | grep Bluetooth Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) lsmod | grep bluetooth bluetooth 158438 10 bnep,rfcomm rfkill list 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: no (wifi working fine. I disabled it using network menu. So, it's fine) dmesg | grep Bluetooth [ 21.981835] Bluetooth: Core ver 2.16 [ 21.981872] Bluetooth: HCI device and connection manager initialized [ 21.981877] Bluetooth: HCI socket layer initialized [ 21.981881] Bluetooth: L2CAP socket layer initialized [ 21.981891] Bluetooth: SCO socket layer initialized [ 21.986047] Bluetooth: RFCOMM TTY layer initialized [ 21.986059] Bluetooth: RFCOMM socket layer initialized [ 21.986065] Bluetooth: RFCOMM ver 1.11 [ 22.361783] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 22.361791] Bluetooth: BNEP filters: protocol multicast So How can I fix this? I saw other place (I don't remember which site) They said, some times, when in windows, if bluetooth disabled by windows driver, It can't be enabled by linux. So, I should install windows and enable blueethooth from windows and then re install linux. That is impossible for me, because I don't have Windows installation media. But I tried this, which is I installed windows xp on virtual box. Vbox showed me thow unknow USB devices. I connected them and installed windows bluethooth drivers to xp. But it didn't ditected Bluethooth either. Also, when I set off mode in hardware switch, those unknown devices disappear from Vbox usb device seletcion menu. So, they are definitely something to do with wifi or bluethooth. Please help me..

    Read the article

  • My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

    - by cwwk
    I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

    Read the article

  • Hardware issues on Samsung NF208 (NF210)

    - by KristoferA - Huagati.com
    I'm trying to get Ubuntu 10.10 running on my wife's Samsung NF208 (same spec as NF210, but shipped without OS), and I have run into a pile of problems: At first, there were problems with audio, display brightness, and WiFi, so I reinstalled Ubuntu from scratch. After reinstalling, the audio has started working but the WiFi loses network access all the time and then it takes 5-10 minutes for it to reconnect to the network. Also, display brightness is at its lowest. I have tried to use the brightness command but it won't run. Is this system utterly incompatible with Ubuntu, or are there working WiFi and display drivers for it somewhere? I have googled for days but haven't found anything useful. Help me. Update: I never got it working properly. I came across lots of useful tips and tricks over at the forum linked to in the accepted answer but I just wasn't able to get it working and stable enough for the intended use. Hopefully a future version of Ubuntu and/or the samsung tools will solve that. Related thread over at the other forum: http://www.voria.org/forum/viewtopic.php?f=3&t=682

    Read the article

  • Xen won't start after it had been working

    - by Paul Tomblin
    I've been setting up this Debian Stable system with a dom0 and 3 domUs. It was working fine for several days, and I'm almost ready to deploy it to the rack. But last night I shut it down with all three domUs still running for the first time, and today when I started it up, xend won't start. In /var/log/messages, I have: Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: blktapctrl: v1.0.0 Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [raw image (aio)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [raw image (sync)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [vmware image (vmdk)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [ramdisk image (ram)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [qcow disk (qcow)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: couldn't find device number for 'blktap0' Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Unable to start blktapctrl and in /var/log/xen/xend.log, I have this: [2010-04-18 12:46:32 3523] INFO (SrvDaemon:219) Xend exited with status 1. [2010-04-18 13:01:34 4255] INFO (SrvDaemon:331) Xend Daemon started [2010-04-18 13:01:34 4255] INFO (SrvDaemon:335) Xend changeset: unavailable. [2010-04-18 13:01:34 4255] INFO (SrvDaemon:342) Xend version: Unknown. [2010-04-18 13:01:34 4255] ERROR (SrvDaemon:353) Exception starting xend (no element found: line 1, column 0) Traceback (most recent call last): File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvDaemon.py", line 345, in run servers = SrvServer.create() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvServer.py", line 251, in create root.putChild('xend', SrvRoot()) File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvRoot.py", line 40, in __init__ self.get(name) File "/usr/lib/xen-3.2-1/lib/python/xen/web/SrvDir.py", line 82, in get val = val.getobj() File "/usr/lib/xen-3.2-1/lib/python/xen/web/SrvDir.py", line 52, in getobj File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvNode.py", line 30, in _ _init__ self.xn = XendNode.instance() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendNode.py", line 709, in instance inst = XendNode() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendNode.py", line 164, in __init__ saved_pifs = self.state_store.load_state('pif') File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendStateStore.py", line 104, in load_state dom = minidom.parse(xml_path) File "/usr/lib/python2.5/xml/dom/minidom.py", line 1915, in parse return expatbuilder.parse(file) File "/usr/lib/python2.5/xml/dom/expatbuilder.py", line 924, in parse result = builder.parseFile(fp) File "/usr/lib/python2.5/xml/dom/expatbuilder.py", line 211, in parseFile parser.Parse("", True) ExpatError: no element found: line 1, column 0 [2010-04-18 13:01:34 4253] INFO (SrvDaemon:219) Xend exited with status 1. Any clues as to what might be going wrong?

    Read the article

  • Getting macro keys from a razer blackwidow to work on linux

    - by Journeyman Geek
    I picked up a razer blackwidow ultimate that has additional keys meant for macros that are set using a tool that's installed on windows. I'm assuming that these arn't some fancypants joojoo keys and should emit scancodes like any other keys. Firstly is there a standard way to check these scancodes in linux? Secondly how do i set these keys to do things in command line and x based linux setups? My current linux install is xubuntu 10.10, but i'll be switching to kubuntu once i have a few things fixed up. Ideally the answer should be generic and system-wide Things i have tried so far: showkeys from the built in kbd package (in a seperate vt) - macro keys not detected xev - macro keys not detected lsusb and evdev output this ahk script's output suggests the M keys are not outputting standard scancodes Things i need to try snoopy pro + reverse engineering (oh dear) Wireshark - preliminary futzing around seems to indicate no scancodes emitted when what i seem to think is the keyboard is monitored and keys pressed. Might indicate additional keys are a seperate device or need to be initialised somehow. Need to cross reference that with lsusb output from linux, in 3 scenarios - standalone, passed through to a windows VM without the drivers installed, and the same with. LSUSB only detects one device on a standalone linux install It might be useful to check if the mice use the same razer synapse driver , since that means some variation of razercfg might work (not detected. only seems to work for mice) Things i have Have worked out: In a windows system with the driver, the keyboard is seen as a keyboard and a pointing device. And said pointing device uses, in addition to your bog standard mouse drivers.. a driver for something called a razer synapse. Mouse driver seen in linux under evdev and lsusb as well Single Device under OS X apparently, though i have yet to try lsusb equivilent on that Keyboard goes into pulsing backlight mode in OS X upon initialisation with the driver. This should probably indicate that there's some initialisation sequence sent to the keyboard on activation. They are, in fact, fancypants joojoo keys. Extending this question a little I have access to a windows system so if i need to use any tools on that to help answer the question, its fine. I can also try it on systems with and without the config utility. The expected end result is still to make those keys usable on linux however. I also realise this is a very specific family of hardware. I would be willing to test anything that makes sense on a linux system if i have detailed instructions - this should open up the question to people who have linux skills, but no access to this keyboard The minimum end result i require I need these keys detected, and usable in any fashion on any of the current graphical mainstream ubuntu varients

    Read the article

  • openstack, bridging, netfilter and dnat

    - by Craig Sanders
    In a recent upgrade (from Openstack Diablo on Ubuntu Lucid to Openstack Essex on Ubuntu Precise), we found that DNS packets were frequently (almost always) dropped on the bridge interface (br100). For our compute-node hosts, that's a Mellanox MT26428 using the mlx4_en driver module. We've found two workarounds for this: Use an old lucid kernel (e.g. 2.6.32-41-generic). This causes other problems, in particular the lack of cgroups and the old version of the kvm and kvm_amd modules (we suspect the kvm module version is the source of a bug we're seeing where occasionally a VM will use 100% CPU). We've been running with this for the last few months, but can't stay here forever. With the newer Ubuntu Precise kernels (3.2.x), we've found that if we use sysctl to disable netfilter on bridge (see sysctl settings below) that DNS started working perfectly again. We thought this was the solution to our problem until we realised that turning off netfilter on the bridge interface will, of course, mean that the DNAT rule to redirect VM requests for the nova-api-metadata server (i.e. redirect packets destined for 169.254.169.254:80 to compute-node's-IP:8775) will be completely bypassed. Long-story short: with 3.x kernels, we can have reliable networking and broken metadata service or we can have broken networking and a metadata service that would work fine if there were any VMs to service. We haven't yet found a way to have both. Anyone seen this problem or anything like it before? got a fix? or a pointer in the right direction? Our suspicion is that it's specific to the Mellanox driver, but we're not sure of that (we've tried several different versions of the mlx4_en driver, starting with the version built-in to the 3.2.x kernels all the way up to the latest 1.5.8.3 driver from the mellanox web site. The mlx4_en driver in the 3.5.x kernel from Quantal doesn't work at all) BTW, our compute nodes have supermicro H8DGT motherboards with built-in mellanox NIC: 02:00.0 InfiniBand: Mellanox Technologies MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR / 10GigE] (rev b0) we're not using the other two NICs in the system, only the Mellanox and the IPMI card are connected. Bridge netfilter sysctl settings: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 Since discovering this bridge-nf sysctl workaround, we've found a few pages on the net recommending exactly this (including Openstack's latest network troubleshooting page and a launchpad bug report that linked to this blog-post that has a great description of the problem and the solution)....it's easier to find stuff when you know what to search for :), but we haven't found anything on the DNAT issue that it causes.

    Read the article

  • Ubuntu 10.04 LTS - Dual monitor works only sometimes (ATI multi-desktop)

    - by Beres Botond
    I've been using my laptop with an external LCD monitor attached to it at work (Philips 201E). And at home with a different external monitor (Samsung 2032BW). I have an ATI graphics card (HD3450), with Ati Catalyst drivers enabled and I'm using the Single display desktop (Multi-Desktop) seeting. At work I have the external monitor on the left and laptop on the right, while at home the other way around. So when I switch between the two setups, I just needed to go to Ati Catalyst Control Center, change the order of the displays, change the resolution (Home - 1680x1050, Work - 1440x900), reboot and it was all fine. But since a while it doesn't work properly anymore: At home it still works fine. At work it doesn't work. Sometimes it works for some reason, after a few resolution/setting changes in ACCC and reboots... it's very strange and annoying. With the home monitor I can see the whole bootup process on both monitors (laptop + LCD) and it always just works fine. With the work monitor on the external LCD monitor I just see "No video input" until I get to the login screen, then it shows up there as well. But after login it will either: Flicker a few times, but then work OK. Or (more often) Flicker once and then go back to "No video input" again. I usually end up rebooting a few times until it works. Does anyone have any idea for fixing it? This is my xorg.conf currently: Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[6]-0" 0 0 Screen "amdcccle-Screen[6]-1" 1280 0 EndSection Section "Files" EndSection Section "Module" Load "glx" EndSection Section "ServerFlags" Option "Xinerama" "off" EndSection Section "Monitor" Identifier "0-LVDS" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x768" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-CRT1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1440x900" EndSection Section "Device" Identifier "Default Device" Driver "fglrx" EndSection Section "Device" Identifier "amdcccle-Device[6]-0" Driver "fglrx" Option "Monitor-LVDS" "0-LVDS" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "amdcccle-Device[6]-1" Driver "fglrx" Option "Monitor-CRT1" "0-CRT1" BusID "PCI:6:0:0" Screen 1 EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[6]-0" Device "amdcccle-Device[6]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[6]-1" Device "amdcccle-Device[6]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

    Read the article

  • Old CRT screen's high resolution doesn't work anymore on windows 7

    - by Mixxiphoid
    One year ago I decided to switch from Windows XP to Windows 7. I had a 17" CRT monitor with a screen resolution of 1600x1200 which worked fine on Windows XP. While installing Windows 7 everything went well until Windows 7 was going to install the video card its driver. Windows 7 puts the screen to its recommended resolution and my screen became black. I waited a few minutes to be sure the installation was finished. I turned off the computer by hand and restarted the computer on a resolution of 800x640. When windows 7 was done installing I went to screen resolutions and the resolution of 1600x1200 was on the top of the list with '(recommended)' next to it. I tried putting it on 1600x1200 but again my screen went black. I installed all windows 7 updates including the video card driver from the NVidia site (NOT from Windows 7). I tried about everything to make it work on 1600x1200 but with no succes. The highest resolution I got with the crt monitor was 1280x1024. I had a TFT screen which had 1280x1024 as max resolution and had better colors, so I used that one till today. My video card is 9600GT and my power supply is beyond sufficient. I even tried to install the driver I had on XP to see if it worked, but no results. I tried classic mode on windows 7, changed the dpi, the frequentie and the monitor settings, but nothing worked. I really like a vertical resolution of 1200, but it seems today I'm bound to all those standard monitors with a resolution of 1980x1024... Can anybody explain to me what the cause is that it worked on Windows XP but not on Windows 7? And maybe a solution to the problem (I actually gave up on getting it fixed...) Thanks a lot in advance. SOLUTION I downloaded the according monitor driver and installed it. Next I rebooted my computer on low resolution (800x640) and connected the CRT monitor. When Windows 7 booted successfully I went to computer management and 'update the driver' of my monitor. I manually selected 'Generic PnP monitor' and made that one active. I want to advanced settings at 'Screen resolution' and selected the mode '1600x1200 (32-bit) 80 Hertz (95 Hertz did not work). Now I had my resolution on 1600x1200. I repeated the earlier step to select the original monitor again instead of the Generic monitor. Quite a way to solve this problem, but it worked! Thanks a lot you all.

    Read the article

  • va_getDriverName() failed with unknown

    - by MIkCode
    i upgraded to 14.04 and afterwards i got an issue with cpu usage when playing HD. I checked the vainfo and this what i got back ibva info: VA-API version 0.35.0 libva info: va_getDriverName() returns -1 libva error: va_getDriverName() failed with unknown libva error,driver_name=(null) vaInitialize failed with error code -1 (unknown libva error),exit I re install the driver sudo apt-get --reinstall install i965-va-driver but i steel got the same error. Any thoghts

    Read the article

  • ODBC and Excel (2 replies)

    Hello, I am using the following connection to Query and Excel Spreadsheet: AConnectionString &quot;Driver {Microsoft Excel Driver (*.xls)};DriverId 790;Dbq &quot; &amp; ofdSelectFile.FileName &amp; &quot;;DefaultDir c:\;&quot; ASourceConnection New Odbc.OdbcConnection(AConnectionString) Dim ADataAdapter as new odbc.odbcDataAdapter(&quot;SELECT * FROM $Sheet1&quot;, ASourceConnection) ADataAdapter.Fill(MyDataset) This works Great, howe...

    Read the article

  • ODBC and Excel (2 replies)

    Hello, I am using the following connection to Query and Excel Spreadsheet: AConnectionString &quot;Driver {Microsoft Excel Driver (*.xls)};DriverId 790;Dbq &quot; &amp; ofdSelectFile.FileName &amp; &quot;;DefaultDir c:\;&quot; ASourceConnection New Odbc.OdbcConnection(AConnectionString) Dim ADataAdapter as new odbc.odbcDataAdapter(&quot;SELECT * FROM $Sheet1&quot;, ASourceConnection) ADataAdapter.Fill(MyDataset) This works Great, howe...

    Read the article

  • help with fixing fwts errors log

    - by jasmines
    Here is an extract of results.log: MTRR validation. Test 1 of 3: Validate the kernel MTRR IOMEM setup. FAILED [MEDIUM] MTRRIncorrectAttr: Test 1, Memory range 0xc0000000 to 0xdfffffff (PCI Bus 0000:00) has incorrect attribute Write-Combining. FAILED [MEDIUM] MTRRIncorrectAttr: Test 1, Memory range 0xfee01000 to 0xffffffff (PCI Bus 0000:00) has incorrect attribute Write-Protect. ==================================================================================================== Test 1 of 1: Kernel log error check. Kernel message: [ 0.208079] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored ADVICE: This is not exactly a failure mode but a warning from the kernel. The _OSI() method has implemented a match to the 'Linux' query in the DSDT and this is redundant because the ACPI driver matches onto the Windows _OSI strings by default. FAILED [HIGH] KlogACPIErrorMethodExecutionParse: Test 1, HIGH Kernel message: [ 3.512783] ACPI Error : Method parse/execution failed [\_SB_.PCI0.GFX0._DOD] (Node f7425858), AE_AML_PACKAGE_LIMIT (20110623/psparse-536) ADVICE: This is a bug picked up by the kernel, but as yet, the firmware test suite has no diagnostic advice for this particular problem. Found 1 unique errors in kernel log. ==================================================================================================== Check if system is using latest microcode. ---------------------------------------------------------------------------------------------------- Cannot read microcode file /usr/share/misc/intel-microcode.dat. Aborted test, initialisation failed. ==================================================================================================== MSR register tests. FAILED [MEDIUM] MSRCPUsInconsistent: Test 1, MSR SYSENTER_ESP (0x175) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0xffffffffffffffff). MSR CPU 0 -> 0xf7bb9c40 vs CPU 1 -> 0xf7bc7c40 FAILED [MEDIUM] MSRCPUsInconsistent: Test 1, MSR MISC_ENABLE (0x1a0) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0x400c51889). MSR CPU 0 -> 0x850088 vs CPU 1 -> 0x850089 ==================================================================================================== Checks firmware has set PCI Express MaxReadReq to a higher value on non-motherboard devices. ---------------------------------------------------------------------------------------------------- Test 1 of 1: Check firmware settings MaxReadReq for PCI Express devices. MaxReadReq for pci://00:00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) is low (128) [Audio device]. MaxReadReq for pci://00:02:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection is low (128) [Network controller]. FAILED [LOW] LowMaxReadReq: Test 1, 2 devices have low MaxReadReq settings. Firmware may have configured these too low. ADVICE: The MaxReadRequest size is set too low and will affect performance. It will provide excellent bus sharing at the cost of bus data transfer rates. Although not a critical issue, it may be worth considering setting the MaxReadRequest size to 256 or 512 to increase throughput on the PCI Express bus. Some drivers (for example the Brocade Fibre Channel driver) allow one to override the firmware settings. Where possible, this BIOS configuration setting is worth increasing it a little more for better performance at a small reduction of bus sharing. ==================================================================================================== PCIe ASPM check. ---------------------------------------------------------------------------------------------------- Test 1 of 2: PCIe ASPM ACPI test. PCIE ASPM is not controlled by Linux kernel. ADVICE: BIOS reports that Linux kernel should not modify ASPM settings that BIOS configured. It can be intentional because hardware vendors identified some capability bugs between the motherboard and the add-on cards. Test 2 of 2: PCIe ASPM registers test. WARNING: Test 2, RP 00h:1Ch.01h L0s not enabled. WARNING: Test 2, RP 00h:1Ch.01h L1 not enabled. WARNING: Test 2, Device 02h:00h.00h L0s not enabled. WARNING: Test 2, Device 02h:00h.00h L1 not enabled. PASSED: Test 2, PCIE aspm setting matched was matched. WARNING: Test 2, RP 00h:1Ch.05h L0s not enabled. WARNING: Test 2, RP 00h:1Ch.05h L1 not enabled. WARNING: Test 2, Device 85h:00h.00h L0s not enabled. WARNING: Test 2, Device 85h:00h.00h L1 not enabled. PASSED: Test 2, PCIE aspm setting matched was matched. ==================================================================================================== Extract and analyse Windows Management Instrumentation (WMI). Test 1 of 2: Check Windows Management Instrumentation in DSDT Found WMI Method WMAA with GUID: 5FB7F034-2C63-45E9-BE91-3D44E2C707E4, Instance 0x01 Found WMI Event, Notifier ID: 0x80, GUID: 95F24279-4D7B-4334-9387-ACCDC67EF61C, Instance 0x01 PASSED: Test 1, GUID 95F24279-4D7B-4334-9387-ACCDC67EF61C is handled by driver hp-wmi (Vendor: HP). Found WMI Event, Notifier ID: 0xa0, GUID: 2B814318-4BE8-4707-9D84-A190A859B5D0, Instance 0x01 FAILED [MEDIUM] WMIUnknownGUID: Test 1, GUID 2B814318-4BE8-4707-9D84-A190A859B5D0 is unknown to the kernel, a driver may need to be implemented for this GUID. ADVICE: A WMI driver probably needs to be written for this event. It can checked for using: wmi_has_guid("2B814318-4BE8-4707-9D84-A190A859B5D0"). One can install a notify handler using wmi_install_notify_handler("2B814318-4BE8-4707-9D84-A190A859B5D0", handler, NULL). http://lwn.net/Articles/391230 describes how to write an appropriate driver. Found WMI Object, Object ID AB, GUID: 05901221-D566-11D1-B2F0-00A0C9062910, Instance 0x01, Flags: 00 Found WMI Method WMBA with GUID: 1F4C91EB-DC5C-460B-951D-C7CB9B4B8D5E, Instance 0x01 Found WMI Object, Object ID BC, GUID: 2D114B49-2DFB-4130-B8FE-4A3C09E75133, Instance 0x7f, Flags: 00 Found WMI Object, Object ID BD, GUID: 988D08E3-68F4-4C35-AF3E-6A1B8106F83C, Instance 0x19, Flags: 00 Found WMI Object, Object ID BE, GUID: 14EA9746-CE1F-4098-A0E0-7045CB4DA745, Instance 0x01, Flags: 00 Found WMI Object, Object ID BF, GUID: 322F2028-0F84-4901-988E-015176049E2D, Instance 0x01, Flags: 00 Found WMI Object, Object ID BG, GUID: 8232DE3D-663D-4327-A8F4-E293ADB9BF05, Instance 0x01, Flags: 00 Found WMI Object, Object ID BH, GUID: 8F1F6436-9F42-42C8-BADC-0E9424F20C9A, Instance 0x00, Flags: 00 Found WMI Object, Object ID BI, GUID: 8F1F6435-9F42-42C8-BADC-0E9424F20C9A, Instance 0x00, Flags: 00 Found WMI Method WMAC with GUID: 7391A661-223A-47DB-A77A-7BE84C60822D, Instance 0x01 Found WMI Object, Object ID BJ, GUID: DF4E63B6-3BBC-4858-9737-C74F82F821F3, Instance 0x05, Flags: 00 ==================================================================================================== Disassemble DSDT to check for _OSI("Linux"). ---------------------------------------------------------------------------------------------------- Test 1 of 1: Disassemble DSDT to check for _OSI("Linux"). This is not strictly a failure mode, it just alerts one that this has been defined in the DSDT and probably should be avoided since the Linux ACPI driver matches onto the Windows _OSI strings { If (_OSI ("Linux")) { Store (0x03E8, OSYS) } If (_OSI ("Windows 2001")) { Store (0x07D1, OSYS) } If (_OSI ("Windows 2001 SP1")) { Store (0x07D1, OSYS) } If (_OSI ("Windows 2001 SP2")) { Store (0x07D2, OSYS) } If (_OSI ("Windows 2006")) { Store (0x07D6, OSYS) } If (LAnd (MPEN, LEqual (OSYS, 0x07D1))) { TRAP (0x01, 0x48) } TRAP (0x03, 0x35) } WARNING: Test 1, DSDT implements a deprecated _OSI("Linux") test. ==================================================================================================== 0 passed, 0 failed, 1 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== ACPI DSDT Method Semantic Tests. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP Failed to install global event handler. Test 22 of 93: Check _PSR (Power Source). ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 22, Detected an infinite loop when evaluating method '\_SB_.AC__._PSR'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 22, \_SB_.AC__._PSR correctly acquired and released locks 16 times. Test 35 of 93: Check _TMP (Thermal Zone Current Temp). ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.DTSZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.DTSZ._TMP correctly acquired and released locks 14 times. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.CPUZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.CPUZ._TMP correctly acquired and released locks 10 times. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 35, Detected an infinite loop when evaluating method '\_TZ_.SKNZ._TMP'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. PASSED: Test 35, \_TZ_.SKNZ._TMP correctly acquired and released locks 10 times. PASSED: Test 35, _TMP correctly returned sane looking value 0x00000b4c (289.2 degrees K) PASSED: Test 35, \_TZ_.BATZ._TMP correctly acquired and released locks 9 times. PASSED: Test 35, _TMP correctly returned sane looking value 0x00000aac (273.2 degrees K) PASSED: Test 35, \_TZ_.FDTZ._TMP correctly acquired and released locks 7 times. Test 46 of 93: Check _DIS (Disable). FAILED [MEDIUM] MethodShouldReturnNothing: Test 46, \_SB_.PCI0.LPCB.SIO_.COM1._DIS returned values, but was expected to return nothing. Object returned: INTEGER: 0x00000000 ADVICE: This probably won't cause any errors, but it should be fixed as the AML code is not conforming to the expected behaviour as described in the ACPI specification. FAILED [MEDIUM] MethodShouldReturnNothing: Test 46, \_SB_.PCI0.LPCB.SIO_.LPT0._DIS returned values, but was expected to return nothing. Object returned: INTEGER: 0x00000000 ADVICE: This probably won't cause any errors, but it should be fixed as the AML code is not conforming to the expected behaviour as described in the ACPI specification. Test 61 of 93: Check _WAK (System Wake). Test _WAK(1) System Wake, State S1. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(2) System Wake, State S2. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(3) System Wake, State S3. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(4) System Wake, State S4. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test _WAK(5) System Wake, State S5. ACPICA Exception AE_AML_INFINITE_LOOP during execution of method COMP WARNING: Test 61, Detected an infinite loop when evaluating method '\_WAK'. ADVICE: This may occur because we are emulating the execution in this test environment and cannot handshake with the embedded controller or jump to the BIOS via SMIs. However, the fact that AML code spins forever means that lockup conditions are not being checked for in the AML bytecode. Test 87 of 93: Check _BCL (Query List of Brightness Control Levels Supported). Package has 2 elements: 00: INTEGER: 0x00000000 01: INTEGER: 0x00000000 FAILED [MEDIUM] Method_BCLElementCount: Test 87, Method _BCL should return a package of more than 2 integers, got just 2. Test 88 of 93: Check _BCM (Set Brightness Level). ACPICA Exception AE_AML_PACKAGE_LIMIT during execution of method _BCM FAILED [CRITICAL] AEAMLPackgeLimit: Test 88, Detected error 'Package limit' when evaluating '\_SB_.PCI0.GFX0.DD02._BCM'. ==================================================================================================== ACPI table settings sanity checks. ---------------------------------------------------------------------------------------------------- Test 1 of 1: Check ACPI tables. PASSED: Test 1, Table APIC passed. Table ECDT not present to check. FAILED [MEDIUM] FADT32And64BothDefined: Test 1, FADT 32 bit FIRMWARE_CONTROL is non-zero, and X_FIRMWARE_CONTROL is also non-zero. Section 5.2.9 of the ACPI specification states that if the FIRMWARE_CONTROL is non-zero then X_FIRMWARE_CONTROL must be set to zero. ADVICE: The FADT FIRMWARE_CTRL is a 32 bit pointer that points to the physical memory address of the Firmware ACPI Control Structure (FACS). There is also an extended 64 bit version of this, the X_FIRMWARE_CTRL pointer that also can point to the FACS. Section 5.2.9 of the ACPI specification states that if the X_FIRMWARE_CTRL field contains a non zero value then the FIRMWARE_CTRL field *must* be zero. This error is also detected by the Linux kernel. If FIRMWARE_CTRL and X_FIRMWARE_CTRL are defined, then the kernel just uses the 64 bit version of the pointer. PASSED: Test 1, Table HPET passed. PASSED: Test 1, Table MCFG passed. PASSED: Test 1, Table RSDT passed. PASSED: Test 1, Table RSDP passed. Table SBST not present to check. PASSED: Test 1, Table XSDT passed. ==================================================================================================== Re-assemble DSDT and find syntax errors and warnings. ---------------------------------------------------------------------------------------------------- Test 1 of 2: Disassemble and reassemble DSDT FAILED [HIGH] AMLAssemblerError4043: Test 1, Assembler error in line 2261 Line | AML source ---------------------------------------------------------------------------------------------------- 02258| 0x00000000, // Range Minimum 02259| 0xFEDFFFFF, // Range Maximum 02260| 0x00000000, // Translation Offset 02261| 0x00000000, // Length | ^ | error 4043: Invalid combination of Length and Min/Max fixed flags 02262| ,, _Y0E, AddressRangeMemory, TypeStatic) 02263| DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, Cacheable, ReadWrite, 02264| 0x00000000, // Granularity ==================================================================================================== ADVICE: (for error #4043): This occurs if the length is zero and just one of the resource MIF/MAF flags are set, or the length is non-zero and resource MIF/MAF flags are both set. These are illegal combinations and need to be fixed. See section 6.4.3.5 Address Space Resource Descriptors of version 4.0a of the ACPI specification for more details. FAILED [HIGH] AMLAssemblerError4050: Test 1, Assembler error in line 2268 Line | AML source ---------------------------------------------------------------------------------------------------- 02265| 0xFEE01000, // Range Minimum 02266| 0xFFFFFFFF, // Range Maximum 02267| 0x00000000, // Translation Offset 02268| 0x011FEFFF, // Length | ^ | error 4050: Length is not equal to fixed Min/Max window 02269| ,, , AddressRangeMemory, TypeStatic) 02270| }) 02271| Method (_CRS, 0, Serialized) ==================================================================================================== ADVICE: (for error #4050): The minimum address is greater than the maximum address. This is illegal. FAILED [HIGH] AMLAssemblerError1104: Test 1, Assembler error in line 8885 Line | AML source ---------------------------------------------------------------------------------------------------- 08882| Method (_DIS, 0, NotSerialized) 08883| { 08884| DSOD (0x02) 08885| Return (0x00) | ^ | warning level 0 1104: Reserved method should not return a value (_DIS) 08886| } 08887| 08888| Method (_SRS, 1, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 1, Assembler error in line 9195 Line | AML source ---------------------------------------------------------------------------------------------------- 09192| Method (_DIS, 0, NotSerialized) 09193| { 09194| DSOD (0x01) 09195| Return (0x00) | ^ | warning level 0 1104: Reserved method should not return a value (_DIS) 09196| } 09197| 09198| Method (_SRS, 1, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1127: Test 1, Assembler error in line 9242 Line | AML source ---------------------------------------------------------------------------------------------------- 09239| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y21._MAX, MAX2) 09240| CreateByteField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y21._LEN, LEN2) 09241| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y22._INT, IRQ0) 09242| CreateWordField (CRES, \_SB.PCI0.LPCB.SIO.LPT0._CRS._Y23._DMA, DMA0) | ^ | warning level 0 1127: ResourceTag smaller than Field (Tag: 8 bits, Field: 16 bits) 09243| If (RLPD) 09244| { 09245| Store (0x00, Local0) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1128: Test 1, Assembler error in line 18682 Line | AML source ---------------------------------------------------------------------------------------------------- 18679| Store (0x01, Index (DerefOf (Index (Local0, 0x02)), 0x01)) 18680| If (And (WDPE, 0x40)) 18681| { 18682| Wait (\_SB.BEVT, 0x10) | ^ | warning level 0 1128: Result is not used, possible operator timeout will be missed 18683| } 18684| 18685| Store (BRID, Index (DerefOf (Index (Local0, 0x02)), 0x02)) ==================================================================================================== ADVICE: (for warning level 0 #1128): The operation can possibly timeout, and hence the return value indicates an timeout error. However, because the return value is not checked this very probably indicates that the code is buggy. A possible scenario is that a mutex times out and the code attempts to access data in a critical region when it should not. This will lead to undefined behaviour. This should be fixed. Table DSDT (0) reassembly: Found 2 errors, 4 warnings. Test 2 of 2: Disassemble and reassemble SSDT PASSED: Test 2, SSDT (0) reassembly, Found 0 errors, 0 warnings. FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 60 Line | AML source ---------------------------------------------------------------------------------------------------- 00057| { 00058| Store (CPDC (Arg0), Local0) 00059| GCAP (Local0) 00060| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00061| } 00062| 00063| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 174 Line | AML source ---------------------------------------------------------------------------------------------------- 00171| { 00172| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00173| GCAP (Local0) 00174| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00175| } 00176| 00177| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 244 Line | AML source ---------------------------------------------------------------------------------------------------- 00241| { 00242| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00243| GCAP (Local0) 00244| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00245| } 00246| 00247| Method (_OSC, 4, NotSerialized) ==================================================================================================== FAILED [HIGH] AMLAssemblerError1104: Test 2, Assembler error in line 290 Line | AML source ---------------------------------------------------------------------------------------------------- 00287| { 00288| Store (\_PR.CPU0.CPDC (Arg0), Local0) 00289| GCAP (Local0) 00290| Return (Local0) | ^ | warning level 0 1104: Reserved method should not return a value (_PDC) 00291| } 00292| 00293| Method (_OSC, 4, NotSerialized) ==================================================================================================== Table SSDT (1) reassembly: Found 0 errors, 4 warnings. PASSED: Test 2, SSDT (2) reassembly, Found 0 errors, 0 warnings. PASSED: Test 2, SSDT (3) reassembly, Found 0 errors, 0 warnings. ==================================================================================================== 3 passed, 10 failed, 0 warnings, 0 aborted, 0 skipped, 0 info only. ==================================================================================================== Critical failures: 1 method test, at 1 log line: 1449: Detected error 'Package limit' when evaluating '\_SB_.PCI0.GFX0.DD02._BCM'. High failures: 11 klog test, at 1 log line: 121: HIGH Kernel message: [ 3.512783] ACPI Error: Method parse/execution failed [\_SB_.PCI0.GFX0._DOD] (Node f7425858), AE_AML_PACKAGE_LIMIT (20110623/psparse-536) syntaxcheck test, at 1 log line: 1668: Assembler error in line 2261 syntaxcheck test, at 1 log line: 1687: Assembler error in line 2268 syntaxcheck test, at 1 log line: 1703: Assembler error in line 8885 syntaxcheck test, at 1 log line: 1716: Assembler error in line 9195 syntaxcheck test, at 1 log line: 1729: Assembler error in line 9242 syntaxcheck test, at 1 log line: 1742: Assembler error in line 18682 syntaxcheck test, at 1 log line: 1766: Assembler error in line 60 syntaxcheck test, at 1 log line: 1779: Assembler error in line 174 syntaxcheck test, at 1 log line: 1792: Assembler error in line 244 syntaxcheck test, at 1 log line: 1805: Assembler error in line 290 Medium failures: 9 mtrr test, at 1 log line: 76: Memory range 0xc0000000 to 0xdfffffff (PCI Bus 0000:00) has incorrect attribute Write-Combining. mtrr test, at 1 log line: 78: Memory range 0xfee01000 to 0xffffffff (PCI Bus 0000:00) has incorrect attribute Write-Protect. msr test, at 1 log line: 165: MSR SYSENTER_ESP (0x175) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0xffffffffffffffff). msr test, at 1 log line: 173: MSR MISC_ENABLE (0x1a0) has 1 inconsistent values across 2 CPUs for (shift: 0 mask: 0x400c51889). wmi test, at 1 log line: 528: GUID 2B814318-4BE8-4707-9D84-A190A859B5D0 is unknown to the kernel, a driver may need to be implemented for this GUID. method test, at 1 log line: 1002: \_SB_.PCI0.LPCB.SIO_.COM1._DIS returned values, but was expected to return nothing. method test, at 1 log line: 1011: \_SB_.PCI0.LPCB.SIO_.LPT0._DIS returned values, but was expected to return nothing. method test, at 1 log line: 1443: Method _BCL should return a package of more than 2 integers, got just 2. acpitables test, at 1 log line: 1643: FADT 32 bit FIRMWARE_CONTROL is non-zero, and X_FIRMWARE_CONTROL is also non-zero. Se

    Read the article

  • Live CD / Live USB much faster than full install

    - by user29347
    I've observed it on both laptops I own! HP Compaq nx6125 and Ubuntu 11.04 x64 - somewhat solved Lenovo Thinkpad T500 and Ubuntu 11.10 x64 - help needed! I'm still struggling with the Thinkpad to get performance level similar to that of 10 y.o. laptops... All in all a really serious issue with multiple versions of Ubuntu that renders computers with perfectly compatible hardware unusable, as far as out of the box experience is concerned. Troubleshooting resultant issues seems to be a hard case even for users with some experience with installing graphics drivers. EDIT: I can't really post additional details. Two different ubuntu versions, two laptops, two different set of graph. drivers (OS vs ATI prop.) - all with the same symptoms. Also I can't stress enough how massive the performance degradation is compared to a healthy system. For that reason I ask for input from people who may know roughly what are we dealing with here. I can post more details if we were to focus on my current Thinkpad T500. In that case my current system details: Lenovo Thinkpad T500 Ubuntu 11.10 x64 ATI Mobility Radeon HD 3650 (also see the "What I have already tried" section about Intel graphics tested) ATI Catalyst 11.10 drivers OCZ Agility 3 SSD but! same with the default driver for ATI the card same with the prop. driver for the ATI card from Jockey (Additional drivers applet) What I have already tried: 0. Switching to Intel integrated card (Intel GMA 4500M HD) with the default driver - same effects = may indicate not driver related problem but a problem with something of global influence like e.g. nomodeset or other I don't even know about. (What you can read above) ATI Catalyst 11.10 and radeon.modeset=0 boot parameter + disabled Wait for VBlank. Unity 2D Ubuntu 10.04 LTS tested (ubuntu-10.04.3-desktop-i386.iso): Both live USB and installed version blazing fast! (on the default drivers - without even installing the proprietary fglrx drivers). re2 a) seems to give me the only significant results (still poor) - perfect Unity elements performance with the same crawling stuttering/lagging when dragging windows around. re2 b) this happens often http://i17.photobucket.com/albums/b68/Bucic/ubuntuforumsorg/Screenshotat2011-10-28083140.png re2 c) Sometimes I am able to witness a normal performance when dragging a window around but only for a second or two. When I try to shake it longer it starts to lag and it will keep lagging like that with an increased probability of what you see in the sshot in point re2 b). re2 d) I can't establish the radeon.modeset=0 influence though. Once it seems to work be smooth with it, the other time - without it. Really can't tell.

    Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >