Search Results

Search found 33445 results on 1338 pages for 'single instance storage'.

Page 1024/1338 | < Previous Page | 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031  | Next Page >

• How to change controller numbering/enumeration in Solaris 10?

  - by Jim

  After moving a Solaris 10 server to a new machine, the rpool disk is now c1t0d0. We have some third party applications hard coded for c0t0d0. How can I change the controller enumeration on this machine? There is no longer a c0. I've tried rebuilding the /etc/path_to_inst, but the instance numbers don't seem to match up with the controller numbers. Also, it's not clear if i86pc platforms use this file. I've tried devfsadm -C to clear the dangling links, but I'm not sure how to cause devfsadm to start numbering from 0 again (or force certain devices in the tree to a specific controller number). Next I am going to try to create the symlinks manually in /dev/dsk and rdsk to point to the correct /devices. I feel like I am going way off path here. Any suggestions? Thanks Update: This is on virtual ESXi hardware with an additional pass-through HBA. There is no controller 0 on the machine, that is for sure. devfsadm -C cleans up all the c0 device symlinks but keeps the already linked controllers at their current ids.

  Read the article

• Recommendations for good FTP server for Win 2008 x64

  - by sfhtimssf1970

  I spent a bunch of time learning/configuring the "all new and better" FTP feature for IIS7. In my opinion, it still fails hard: In order to have multiple FTP sites on the same machine, you have to use host|user usernames (like domain.com|jason) for every account. Using IIS Manager auth doesn't seem to work at all. I'm sure I'm doing something wrong, but I can't figure out what the hell it is. I've read all the official articles on it and configured it a hundred different ways. Doesn't play well with passive connection types. That has to be disabled on the client in order for it to work. Doesn't have any way to allow one user to see multiple sites no matter what binding they are connected to. For instance, if "jason" connects to ftp.domain.com, he should be able to see domain2.com, domain3.com without seeing domain4.com and domain5.com. It takes an act of God to set this up with IIS7. So I'm wanting to install a third party FTP server instead. I've looked at FileZilla both ZFTPServer. Anyone know of any pros/cons on these? Any other recommendations?

  Read the article

• Can't add service account to domain group during SQL cluster install

  - by Sam

  I'm installing a 2008 instance on a Server 2003 machine which is already running SQL 2005. I need to set up domain groups for the security setup step: http://msdn.microsoft.com/en-us/library/ms179530.aspx On Windows Server 2003, specify domain groups for SQL Server services. All resource permissions are controlled by domain-level groups that include SQL Server service accounts as group members. Much more info on this here: http://support.microsoft.com/kb/910708 I've had problems with being able to add the windows service accounts to the groups at install time. The security admins had to make my account a domain admin - which they were hesitant to do. The account under which SQL Server Setup is running must have permissions to add accounts to the domain groups. Is there a specific security setting which would allow my account to add accounts to a group? UPDATE: I'm looking for specific instructions. I have a global group called domain\servicegroup - what do I tell the security folks to do. I'd love to figure it out myself, but I don't have access to this stuff.

  Read the article

• SharePoint solution package not deploying to all front-ends

  - by Alex

  I have a WSP that contains a web part. It's being built using WSPBuilder. Most of the time, the WSP deploys perfectly. However, in two of our test environments (and sadly, in production, too) the WSP doesn't deploy properly to all the web front ends. The assemblies make it into the GAC, and the .webpart files get provisioned. The problem is that a tool part that the web part relies on for configuration simply fails to appear. I've determined that every time this has happened, it has been isolated to a single web front end. I've been able to resolve the issue by doing an stsadm -o deploysolution to re-deploy the solution, and in one instance it was resolved by the end user deactivating/reactivating the feature. Unfortunately, though, this has made it impossible to determine if the control isn't being deployed properly, or if it's some other issue. Any thoughts on this? Could it be a problem with the WSP, or is it likely to be environmental?

  Read the article

• Does a Windows 7 dvd only have one language?

  - by user326639

  I'm a Dutch developer living in Spain. I recently composed a new computer from new parts and I installed Windows 7 Professional 64 bit (OEM) on it. On the web site of the on-line shop there was a note saying "language: Spanish". Because my English is quite a bit better than my Spanish, but mainly because it is much easier to find information on the web in English, I want my OS to be in English. I asked the on-line shop if they also sold the UK version of Windows 7 but they assured me that "all Windows 7 versions are multi-language". With the installation of XP a few years ago, I remember that I was offered the option English or Spanish while the installation process was still in the DOS-like (non-graphical) screen. While installing Windows 7, I did not see any non-graphical screen and the first time I was asked about the language, was in a drop-down list that contained only Spanish. I know about the language pack possibility of Windows 7, but this is not available on Professional. Even if I had Ultimate, I don't know if it would be possible to install Windows in Spanish, and then add English as a second language from a language pack. I get the impression that English has to be the base-language. Furthermore, I am a bit sceptical until I'd see it in action. What happens with shortcuts (i.e. Select All: ctrl-a in English / ctrl-e in Spanish, and what about logging messages in Event Viewer, etc) So can anybody tell me how it works with languages in Windows 7? Have I been misinformed by the computer shop? Could it be that OEM versions of Windows are single language an a full installation is not?

  Read the article

• Safari's location bar (auto-suggest and web search)

  - by Lri

  Auto-suggest don't seem to work for queries with spaces. Am I missing something? If you select an item from the suggestion list that was matched by its title, the title is filled in before the address. Can you change it to work like in other browsers? SMRT disables searching by title completely. Can you combine Top Hit, History and Bookmarks into a single section? The preferences starting with DebugSafari4 don't work anymore. (Like DebugSafari4IncludeFancyURLCompletionList.) Can you direct unresolved addresses to something like google.com/search?q=?&btnI instead of ?.com? Like by changing keyword.URL in Firefox. Can you remove or hide the web search field? In Camino, Cruz and Fluid it can be resized to zero width. You can't circumvent the normal maximum ratio with InputFieldWidthRatio. AddressBarIncludesGoogle doesn't appear do anything in the current version. Are there fixes or workarounds to any of these? I'm lumping these issues together, because they are closely related — a lot of them were introduced when the location bar was redesigned in Safari 5. I'm also hoping to find something like an extension or a plugin that would replace the standard location bar.

  Read the article

• BGP Multihomed/Multi-location best practice

  - by Tom O'Connor

  We're in the process of designing a new iteration of our network where we improve resilliency by adding a second datacentre. We'll be adding a second datacentre, with an identical configuration of servers as our primary location. To achieve network connectivity, we're looking into a couple of possible methods. See earlier questions http://serverfault.com/questions/86736/best-way-to-improve-resilience and http://serverfault.com/questions/101582/dns-round-robin-failover-and-load-balancing I'm pretty convinced that BGP is the right way to go about this, and this question is not about RRDNS. 1) If we have 2 locations, do we announce the same IP address block from both locations? 2) If we did this, but had a management ssh interface on x.x.x.50 from datacentre A, but it was on x.x.x.150 in datacentre B. What is the best practice mechanism for achieving this? Because if I were nearest to A, then all my traffic would go to x.50, but if i attempted to connect to x.150, I'd not be able to connect, because this address wouldn't be valid at A, but only at B. Is the best solution to announce 2 different netblocks, one at each location, facilitating the need for RRDNS, or to announce a single block, and run some form of VPN between the two sites for managment traffic?

  Read the article

• How can I get my routers to forward ports correctly?

  - by Giffyguy

  My network currently looks like this (simplified): Note that Router #2 is connected to the LAN interface of Router #1. This should be familiar to anyone who has seen a standard static-IP setup with an additional firewall for a residence or other small building. Router #1 is actually my cable gateway, but since it is a fully functional router/firewall, I am going to refer to it as a router. Now, I need to open various ports in both firewalls for incoming communication to my server - port 80 is a good example. So I've opened up port 80 in Router #2, and so far all incoming traffic at the public IP X.X.X.129 is being routed correctly. The problem is that I also need my server to respond to incoming traffic at the public IP X.X.X.130 on the WAN interface of Router #1. Naturally, I can't just tell Router #1 to forward port 80 to another public IP. Port forwarding is only supported when the traffic is being directed to the LAN subnet. I am willing to restructure my network topology if required, with the following conditions: Router #1 cannot have its WAN IP reassigned - X.X.X.130 is mandatory. Router #1 cannot be moved or disconnected from the cloud. The server cannot be given a second IP address. I would prefer the server to have a private IP address - e.g. 10.0.0.10 I'd like to keep Router #2, but it can have a private IP - e.g. 10.0.1.10 Following these rules, I need to get my server to receive incoming traffic on port 80 from both public IP addresses. Does anyone on SU know if this is possible? So far my only theories have been to set up a static route on either router, or to somehow combine my two subnets into a single subnet.

  Read the article

• tail -f and then exit on matching string

  - by Patrick

  I am trying to configure a startup script which will startup tomcat, monitor the catalina.out for the string "Server startup", and then run another process. I have been trying various combinations of tail -f with grep and awk, but haven't got anything working yet. The main issue I am having seems to be with forcing the tail to die after grep or awk have matched the string. I have simplified to the following test case. test.sh is listed below: #!/bin/sh rm -f child.out ./child.sh > child.out & tail -f child.out | grep -q B child.sh is listed below: #!/bin/sh echo A sleep 20 echo B echo C sleep 40 echo D The behavior I am seeing is that grep exits after 20 seconds , however the tail will take a further 40 seconds to die. I understand why this is happening - tail will only notice that the pipe is gone when it writes to it which only happens when data gets appended to the file. This is compounded by the fact that tail is to be buffering the data and outputting the B and C characters as a single write (I confirmed this by strace). I have attempted to fix that with solutions I found elsewhere, such as using unbuffer command, but that didn't help. Anybody got any ideas for how to get this working how I expect it? Or ideas for waiting for successful Tomcat start (thinking about waiting for a TCP port to know it has started, but suspect that will become more complex that what I am trying to do now). I have managed to get it working with awk doing a "killall tail" on match, but I am not happy with that solution. Note I am trying to get this to work on RHEL4.

  Read the article

• Can't login via ssh after upgrading to Ubuntu 12.10

  - by user42899

  I have an Ubuntu 12.04LTS instance on AWS EC2 and I upgraded it to 12.10 following the instructions at https://help.ubuntu.com/community/QuantalUpgrades. After upgrading I can no longer ssh into my VM. It isn't accepting my ssh key and my password is also rejected. The VM is running, reachable, and SSH is started. The problem seems to be about the authentication part. SSH has been the only way for me to access that VM. What are my options? ubuntu@alice:~$ ssh -v -i .ssh/sos.pem [email protected] OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/ubuntu/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to www.hostname.com [37.37.37.37] port 22. debug1: Connection established. debug1: identity file .ssh/sos.pem type -1 debug1: identity file .ssh/sos.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: RSA 33:33:33:33:33:33:33:33:33:33:33:33:33:33 debug1: Host '[www.hostname.com]:22' is known and matches the RSA host key. debug1: Found key in /home/ubuntu/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: .ssh/sos.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentications that can continue: publickey,password Permission denied, please try again.

  Read the article

• Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

  - by Sky

  first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

  Read the article

• How can I tell which page is creating a high-CPU-load httpd process?

  - by Greg

  I have a LAMP server (CentOS-based MediaTemple (DV) Extreme with 2GB RAM) running a customized Wordpress+bbPress combination . At about 30k pageviews per day the server is starting to groan. It stumbled earlier today for about 5 minutes when there was an influx of traffic. Even under normal conditions I can see that the virtual server is sometimes at 90%+ CPU load. Using Top I can often see 5-7 httpd processes that are each using 15-30% (and sometimes even 50%) CPU. Before we do a big optimization pass (our use of MySQL is probably the culprit) I would love to find the pages that are the main offenders and deal with them first. Is there a way that I can find out which specific requests were responsible for the most CPU-hungry httpd processes? I have found a lot of info on optimization in general, but nothing on this specific question. Secondly, I know there are a million variables, but if you have any insight on whether we should be at the boundaries of performance with a single dedicated virtual server with a site of this size, then I would love to hear your opinion. Should we be thinking about moving to a more powerful server, or should we be focused on optimization on the current server?

  Read the article

• Upgrading memory on an IBM Power 710 Express (8231-E2B)

  - by cairnz

  We have a Power 710 Express server that was loaded with 4x4 GB memory on a single riser card. I have replaced the 4 chips with 4x8GB and put in another riser card and loaded it with 4x8GB more for a total of 64GB memory. The firmware is AL730_078. When i power it on, the service processor boots up and i can access the ASMi. From here I can look at "Memory Serial Presence Data" and see that the system in some way detects 8x8 GB. However when i look at Hardware Deconfiguration and specifically Memory Deconfiguration, it is still listed with old values, 16384MB, and claims there are 4x4 chips in the C17 riser. How do i proceed to make the server recognize properly the amount of memory installed? I get a FSPSP04 and B181B50F progress code on booting because (i think) it hasn't been told the memory has changed. It then does not proceed to booting the operating system (VIOS) when turned on. Are there any steps I have overlooked here? Can I do some commands, either on the service processor, or otherwise, to tell the system to configure with the proper amount of memory? PS: This is a stand alone server, not configured with HMC or SDMC.

  Read the article

• JBoss7 load balancing with mod_proxy_balancer - session not working

  - by Phil P.

  I am trying to set up mod_proxy_balancer for routing requests to 2 jboss7-servers. For the time being I am testing this setup on my local machine, using following config in httpd.conf: ProxyRequests Off <Proxy \*> Order deny,allow Deny from all </Proxy> ProxyPass / balancer://mycluster/ stickysession=JSESSIONID|jsessionid scolonpathdelim=On <Proxy balancer://mycluster> BalancerMember http://localhost:8080 route=node1 BalancerMember http://localhost:8081 route=node2 Order allow,deny Allow from all </Proxy> and in the standalone.xml file of each jboss I have defined the jvmRoute system property: <system-properties> <property name="jvmRoute" value="node1"/> </system-properties> At http:// localhost/myapp the application is accessible but the java-session is not build up correctly. Consequently the authentication is not working. The funny thing is, that everything is working if I turn off one JBoss-instance. As I have tried a couple of settings already, I am thankful for any further suggestions.

  Read the article

• How to activate Win XP from Windows 7 compatibility mode on MacOS Parallels 5

  - by Ben Hammond

  I am running Parallels Desktop 5.0.9344 for Mac. I am running Mac OS 10.6.3 10D2094 I have bought a retail copy of Window 7 professional specifically because I need the XP compatibility. Windows 7 is installed and working. I have problems with the XP activation Windows7 'Virtual PC' does not run under Parallels (strange error about Server Execution failed 0x80080005). I have used the Parallels Transporter to convert the "Windows XP Mode Base.vhd" file into a parallels Virtual Machine. This copy of XP now starts normally, however it records itself as unregistered. There was a KEY.txt file in the same directory as the .vhd file; although this file contains a valid-looking activation key, it does not appear to activate the instance of XP. I have also tried to enter the Win7 activation key; this does not work either. I have tried calling the two phone numbers; an automated system asked me to enter 56 digits through the telephone and then accused me of being a pirate. I believe it may be possible to install Win7 via Bootcamp, start WinXP under Virtual PC, activate it and then import this activated .vhd into Parallels; but that seems a long way round, and is far from certain. What can I do to get WinXP running under Mac Parallels Desktop ?

  Read the article

• Connect over WiFi to SQL Server from another computer

  - by Bronzato

  I tried to connect over WiFi to SQL Server with SQL Server Management Studio from another computer, but it failed. I have a computer with Windows 7 & SQL Server 2008 (lets say the server computer). Next to it I have a freshly installed computer with Windows 7 & SQL Server Management Studio (let's say the client computer). What I did on the server computer: Configure firewall by enabling port 1433 Enabled network protocols (TCP/IP) inside SQL Server Configuration Manager Checked Allow remote connections to this server in server properties in the SQL Server Management application. Started SQL Server Browser Restarted services (SQL Server Browser is stopped at this point, but I don't think it is necessary. Is it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to SQL Server on my server computer. Ok, something new with this problem: Until now, I successfully connected to my "server computer" with Management Studio. What I did is type the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of SQL server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name. Now my new challenge is to be successful in connecting my VB6 application to this remote database located on my "server computer". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's going wrong?

  Read the article

• How to solve SocketException: Permission denied: connect

  - by luxinxian

  I recently encountered a problem that is giving me a headache and I need help ... The System consists of two subsystems, called A and B, each running on a standalone Tomcat instance and currently running on the same machine. A invokes B's service via Spring httpInvoker (i.e. over HTTP). B system also invokes the other system's services via HTTP. Symptoms: the system starts to run and appears to work normally for around 10-15 days; the system will run for a period of time after an exception: org.springframework.remoting.RemoteAccessException: Could not access HTTP invoker remote service at [http://xxx.xxx.xxx.xxx/remoting/call]; The nested exception is java. net.SocketException: **Permission denied: connect** when the exception occurs, the system continues. This happens always, not only occasionally. (It looks like some resources are exhausted, but CPU rate < 5%, memory < 15%, network < 5%). when the system call between A and B fails, the B system call over HTTP to an external service also failed, with the same exception. Restarting both Tomcat services makes the whole system work properly. So repeatedly following steps 1 - 5, I have not found the root reason. Environment: windows 2008 R2 tomcat7.0.42 x86_64 oralce-jdk-1.7.0_40 Any ideas?

  Read the article

• Should I enabled 802.3x hardware flow control?

  - by Stu Thompson

  What is the conventional wisdom regarding 802.3x flow control? I'm setting up a network at a new colo and am wondering if I should be enabling it or not. My oh-cool-a-bright-and-shiny-new-toy self wants to enable it, but this seems like one of those decisions that could blow up in my face later on. My network: An HP ProCurve 2510G-24 switch A pair of Debian 5 HP DL380 G5's with built-in NC373i 2-port NIC LACP'd as one link. 9000 jumbo frames enabled. (Application) A pair of hand-built Ubuntu server with 4-port Intel Pro/1000 LACP'd as one link. 9000 jumbo frames enabled. (NAS) A few other servers with with single 1Gbps ports, but one with 100Mbps. Most of this kit is 802.3x. I've been enabling it as I go along, and am about to test the network. But as my 'go live' day nears, I am worried about the 802.3x decision as I've never explicitly used it before. Also, I've read some 10-year old articles out there on the Intertubes that warn against using flow control. Should I be enabling 802.3x hardware flow control?

  Read the article

• How can I setup apache+mod_proxy so when I connect to mod_proxy on interface X, it sends the traffic

  - by aspitzer

  We use a service that allots us X number of requests per IP and has allows us to setup 5 IPs with such a limit (I know.. it seems stupid they could not just up the limit 5x on one IP). Pretend I have a linux box with the following address on the internet: 66.249.90.104 - that is an Google IP and not mine... so feel free to try to hack into it :) I setup apache+mod_proxy as a forwarding proxy (ProxyRequests On). i.e. you can setup firefox to use 66.249.90.104:8080 as a proxy, and all firefox traffic comes out as 66.249.90.104. So far so good. Problem: Now I add more alias interfaces so the total looks like this: eth0: 66.249.90.104 eth0:1 66.249.90.105 eth0:2 66.249.90.106 eth0:3 66.249.90.107 eth0:4 66.249.90.108 I run apache+mod_proxy (single apache instance) which binds to all interfaces, but no matter which address I connect to use the forwarding proxy, all traffic goes out to the internet as 66.249.90.104 I have also tried running 5 different apaches, each binding to its own interface only, but that still sends the outbound request through 66.249.90.104. I was hoping to get it to work as follows: I connect to 66.249.90.108 and make a proxy request, and it goes out as 66.249.90.108. I connect to 66.249.90.107 and make a proxy request, and it goes out as 66.249.90.107. etc. Has anyone else had to deal with this issue? The fall back solution would be to just run apache on 5 separate boxes, but I would prefer it to all work on one box. Thanks!

  Read the article

• Refresh file access time under Linux / Discard disk read cache

  - by calandoa

  I am making use of the access time to analyse some build process, but it is not working the way I want: the access time is updated the first time I read the file, then it stays the same for a long while, or until the next reboot. For instance: $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 10:03 some_file $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time is updated # waiting a few minutes... $ grep abcdef some_file $ ll -u some_file -rw-r--r-- 1 root root 1.3M 2010-04-07 11:24 some_file # The access time has not been updated :( I suppose that the file is buffered by Linux in the free memory, the only this copy is accessed the subsequent times for speed reasons. A solution would be to discard the buffers in memory. After searching some forums, I found: sync echo 1 > /proc/sys/vm/drop_caches echo 2 > /proc/sys/vm/drop_caches echo 3 > /proc/sys/vm/drop_caches But it is not working, it seems that it only sync up the write buffers, not the read ones. May be it is due to some custom kernel configuration on my distro (fedora 9)? Or I am missing something here? Is there a way to achieve this access time refresh? Note also that I do not want to simulate some writes on my entire file tree. Because I am using some makefile based build system, this will cause the entire project to be build again.

  Read the article

• QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

  - by Horst Walter

  On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

  Read the article

• how to remove an entry from system tray?

  - by altvali

  I've searched for an answer to this one and I haven't found one yet. How do i remove a single item from Windows' System tray? I'm targeting Windows XP. Edit: This is not about preventing items from starting up. I want the program to keep running, I just need another script/program to remove the first one's entry from system tray. Second Edit: One approach that I can think of is to try to hide the intended app by modifying registry keys. On several test machines I've found some registry entries that match the System tray information at HKEY_USERS\something-that-looks-like S-1-5-21-682003330-1563985344-725345543-1003\Software\Microsoft\Windows\CurrentVersion\Explorer\TrayNotify with BalloonTip, IconStream and PastIconsStream containing systray information. The important one is IconStream. On other machines, these are found at hkey_classes_root/local/setting/software/microsoft/windows/currentversion/TrayNotify I'm quite sure there's no danger in changing those specific registries, but I don't know how to write code for that. Can anyone help me with the code and with confirming if this has the desired effect of hiding the systray icon for an active program?

  Read the article

• Managing a test iSCSI target server

  - by dyasny

  Hi all, I am using a RHEL server with a few hard drives, and tgtd as the iscsi target software. I a looking for a way to allocate and deallocate space and targets with that space, without restarting my system, or harming other LUNs. Currently, all my HDDs are PVs in a single VG, and I lvcreate/lvremove as required, and then export the allocated LVs using a tgt script: usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.lab.gss:300gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_300Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=2 --targetname iqn.2001-04.com.lab.gss:200gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 2 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_200Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 2 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=3 --targetname iqn.2001-04.com.lab.gss:100gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 3 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_100Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 3 -I ALL tgtadm --mode target --op show So in order to remove a LUN, I stop the tgtd service, lvremove the lv, and remove the entry from the iscsi target script When I add a lun, I run lvcreate, and then add an entry to the script and run it. This is not quite optimal, since restarting the service is a bad idea while other LUNs are busy, so I am looking for a more scalable and safer way. Thanks

  Read the article

• ffmpeg rotate mp4 90º

  - by shox

  Hi, can I rotate(+save / reencode) a .mp4 with ffmpeg? The only thing I found was on the mailinglist saying -vfilters "rotate=90" but ffmpeg says no vfilters. Tried -vf, it says there is no rotate. If I try to do it in VLC it simply does not rotate and kills the audio (did the vlc encoding EVER work? Every single freakin video I throw at it gets fu****d up in some way -_- ) I'm on a MAC and don't have iWork. Any ideas? Thanks FFmpeg version git-svn-r23607, Copyright (c) 2000-2010 the FFmpeg developers built on Jun 14 2010 23:52:55 with gcc 4.2.1 (Apple Inc. build 5659) configuration: libavutil 50.19. 0 / 50.19. 0 libavcodec 52.76. 0 / 52.76. 0 libavformat 52.68. 0 / 52.68. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.11. 0 / 0.11. 0 Hyper fast Audio and Video encoder

  Read the article

• apache2 + mod_fastcgi + suexec + php5.2 = unstable on high load...

  - by redguy..pl

  I am hosting several (~30) different sites on one server with apache2+fastcgi+suexec+php5. Sites have different loads and different execution times of their scripts (some of them process request for 5-7 seconds, some <1sek). Sometimes when single site receives very high load (all php instances of this site are created and used) - whole apache server hangs. Apache (worker mpm) creates new processes up to the upper limit. It looks like it is starting to queue ALL new request for EVERY site, not only the one that has high load and quickly achieves process limits... restart of apache solves the problem... config: FastCgiConfig -singleThreshold 1 -multiThreshold 10 -listen-queue-depth 30 -maxProcesses 80 -maxClassProcesses 12 -idle-timeout 30 -pass-header HTTP_AUTHORIZATION -pass-header If-Modified-Since -pass-header If-None-Match (earlier have default -listen-queue-depth = 100, but it didn't change anything...) Any suggestions? Another question - how is implemented this listen queue? is it one queue for whole apache, or unique queue for every defined php apllication (suexec site)? I would like to achieve something like this: when one site receives high load and its queue is full - server bounces next request, but only for this one site.. Other sites should work properly...

  Read the article

< Previous Page | 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031  | Next Page >