Search Results

Search found 54475 results on 2179 pages for 'tired of trying'.

Page 103/2179 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• Network Load Balancing, intermittent port problem

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

• Windows Virtual Machines will not run

  - by jlego

  I'm trying to setup a few virtual machines to use for testing websites in the various old versions of IE. I had Microsoft Virtual PC working on an older machine using XP mode and 2 other VHD's from Microsoft that allowed me to test in IE6-IE8. I've recently gotten a new work machine and am trying to set up the VMs again for testing, however nothing seems to be working. Both the old and the new system run Windows 7 64-bit Ultimate with AMD processors. I downloaded Virtual PC & XP mode from here http://www.microsoft.com/windows/virtual-pc/download.aspx and go through the installation process. XP mode is installed, but when I try to run it it goes through the initial setup process only to fail when it is almost complete with the error "Cannot Complete Setup". (After googling I see that this might be a conflict with my processor) I download other VHD's from here http://www.microsoft.com/windows/virtual-pc/download.aspx in order to get the other versions of IE and try to set those up in Virtual PC as well. I click on them to start the machine and both Windows 7 with IE8 and Windows Vista with IE7 just hang at a black screen. I try to use Virtual Box instead, and I get Windows XP with IE6 running, but I have no internet connection in the VM. I try all different settings and try to google the correct settings but nothing seems to work. When I load the VM, XP shows that its found new hardware but it needs the drivers. One of these pieces of hardware is the network adapter, but I can't connect to the internet to download the driver in the guest OS. VirtualBox tells me I need to install extensions in order for things to function properly. I go through the installation process in the guest OS and restart the VM, however now XP is asking for validation and I can't access the VM. I try installing the other 2 OS (Vista & 7) but I get a BSOD right after the startup screen appears and the VM restarts itself. I'm getting so frustrated trying to make this work, I would really appreciate any assistance on getting the VMs up and running or any alternatives for testing websites in Internet Explorer.

  Read the article

• IIS 7.5 FTP Service crashes after installation of Advanced Logging 1.0 Module

  - by Jeremy

  I've recently been tasked with setting up two new productions servers for an ASP.Net application. The servers sit behind a F5 Load Balancer, which in turn forwards the end users IP address forward via the standard X_Forwarded_For HTTP Header. All of the reading that I have done suggests that I need to install the IIS Advanced Logging Module in order to take advantage of the X_Forwarded_For HTTP Header. Some quick background: Both of the web servers are Windows 2008 R2 Standard (x64), with IIS 7.5 installed and configured. The FTP Role has also been installed, configured and is operational. The Issue After installing the IIS Advanced Logging module via the Web Platform Installer, I noticed the following Error in the Event Viewer: The FTP Service encountered an error trying to read configuration data from file \?\C:\Windows\system32\inetsrv\config\applicationHost.config, line number 374. The error message is: Unrecognized element 'advancedLogging' Trying to connect over FTP to either of the web servers results in a 530. I've spent 2 hours scouring Google trying to find a solution, short of uninstalling the Advanced Logging Module. As far as I can tell, there is no way to turn off Advanced Logging on a site per site basis. Help would be appreciated.

  Read the article

• NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

  - by Corey Kennedy

  What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help!

  Read the article

• How do I resolve certificate errors on HP blade center

  - by Martin Hilton

  I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

  Read the article

• Why is OpenSSH not using the user specified in ssh_config?

  - by Jordan Evens

  I'm using OpenSSH from a Windows machine to connect to a Linux Mint 9 box. My Windows user name doesn't match the ssh target's user name, so I'm trying to specify the user to use for login using ssh_config. I know OpenSSH can see the ssh_config file since I'm specifying the identify file in it. The section specific to the host in ssh_config is: Host hostname HostName hostname IdentityFile ~/.ssh/id_dsa User username Compression yes If I do ssh username@hostname it works. Trying using ssh_config only gives: F:\>ssh -v hostname OpenSSH_5.6p1, OpenSSL 0.9.8o 01 Jun 2010 debug1: Connecting to hostname [XX.XX.XX.XX] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa-cert type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa type 2 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debia n-3ubuntu5 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname' is known and matches the RSA host key. debug1: Found key in /cygdrive/f/progs/OpenSSH/home/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa debug1: Offering DSA public key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I was under the impression that (as outlined in this question: How to make ssh log in as the right user?) specifying User username in ssh_config should work. Why isn't OpenSSH using the username specified in ssh_config?

  Read the article

• Gwibber doesnt launch post upgrade

  - by Arcath

  i updated my pc from ubuntu 9.10 to 10.04 and one of the things i was looking forward too was the "me menu" and gwibber. For some reason gwibber doesnt launch at all. when i try to launch it from terminal i get: [21:02:20][arcath@Highgate ~]$ gwibber ** (gwibber:8182): WARNING **: Trying to register gtype 'WnckWindowState' as enum when in fact it is of type 'GFlags' ** (gwibber:8182): WARNING **: Trying to register gtype 'WnckWindowActions' as enum when in fact it is of type 'GFlags' ** (gwibber:8182): WARNING **: Trying to register gtype 'WnckWindowMoveResizeMask' as enum when in fact it is of type 'GFlags' Traceback (most recent call last): File "/usr/bin/gwibber", line 50, in <module> from gwibber import client File "/usr/lib/python2.6/dist-packages/gwibber/client.py", line 3, in <module> import gtk, gobject, gwui, util, resources, actions, json, gconf File "/usr/lib/python2.6/dist-packages/gwibber/gwui.py", line 2, in <module> import os, json, urlparse, resources, util File "/usr/lib/python2.6/dist-packages/gwibber/util.py", line 2, in <module> from microblog.util.couch import RecordMonitor File "/usr/lib/python2.6/dist-packages/gwibber/microblog/util/couch.py", line 10, in <module> OAUTH_DATA = desktopcouch.local_files.get_oauth_tokens() File "/usr/lib/python2.6/dist-packages/desktopcouch/local_files.py", line 323, in get_oauth_tokens oauth_token_secrets = cf.items_in_section("oauth_token_secrets")[0] File "/usr/lib/python2.6/dist-packages/desktopcouch/local_files.py", line 189, in items_in_section raise ValueError("Section %r not present." % (section_name,)) ValueError: Section 'oauth_token_secrets' not present. and i cant work out whats wrong with it. Can anyone point me in the right direction?

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• MOSS2007 tries to use ActiveDirectory when I have configured an alternative membership provider

  - by glenatron

  I've got a MOSS site that I am trying to configure using Forms authentication and absolutely any kind of membership provider whatsoever. Thus far ActiveDirectory has proved obstructively difficult so I've just whipped up a simple stub membership provider and put it in the GAC. It's a very basic and simple provider but it works fine with an ASP.Net site, I just can't make it work with Sharepoint. On Sharepoint I get the following error when I look for StubProvider:Bob ( or anything else for that matter) from the "Policy For Web Application" people picker: Error in searching user 'StubProvider:bob' : System.ComponentModel.Win32Exception: Unable to contact the global catalog server at Microsoft.SharePoint.Utilities.SPActiveDirectoryDomain.GetDirectorySearcher() at Microsoft.SharePoint.WebControls.PeopleEditor.SearchFromGC(SPActiveDirectoryDomain domain, String strFilter, String[] rgstrProp, Int32 nTimeout, Int32 nSizeLimit, SPUserCollection spUsers, ArrayList& rgResults) at Microsoft.SharePoint.Utilities.SPUserUtility.SearchAgainstAD(String input, SPActiveDirectoryDomain domainController, SPPrincipalType scopes, SPUserCollection usersContainer, Int32 maxCount, String customQuery, TimeSpan searchTimeout, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPActiveDirectoryPrincipalResolver.SearchPrincipals(String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPUtility.SearchPrincipalFromResolvers(List`1 resolvers, String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount, Dictionary`2 usersDict). The Provider is named as Authentication Provider for the Site Collection in question. As far as I can tell this is because Sharepoint is still trying to access ActiveDirectory rather than talking to the provider I'm asking it to use. My Sharepoint Central Administration section includes this: <membership> <providers> <add name="StubProvider" type="StubMembershipProvider.Provider, StubMembershipProvider, Version=1.0.0.0, Culture=neutral, PublicKeyToken=5bd7e2498c3e1a03" /> </providers> </membership> And also: <PeoplePickerWildcards> <clear /> <add key="StubProvider" value="%" /> </PeoplePickerWildcards> Is there a clear reason why this would not be accessible from the PeoplePicker or why it is still trying to use ActiveDirectory? I've made sure I reset IIS and even restarted the server to see if either of those helped but they made no difference.

  Read the article

• Can I use IIS to do ActiveDirectory single-sign-on for another website?

  - by brofield

  I'm trying to add Active Directory single-sign-on support to an existing SOAP server. The server can be configured to accept a trusted reverse-proxy and use the X-Remote-User HTTP header for the authenticated user. I want to configure IIS to be the trusted proxy for this service, so that it handles all of the Active Directory authentication for the SOAP server. Basically IIS would have to accept HTTP connections on port X and URL Y, do all the authentication, and then proxy the connection to a different server (most likely the same X and Y). Unfortunately, I have no knowledge of IIS or AD (so I am trying my best to learn enough to build this solution) so please be gentle. I would assume that this is not an uncommon scenario, so is there some easy way to do this? Is this sort of functionality built into IIS or do I need to build some sort of IIS proxy program myself? Is there a better option for getting the authentication done and the X-Remote-User HTTP header set than requiring IIS? Update: For example, what I am trying to create is: [CLIENT] [IIS] [AD] [SOAP-SERVER] 1. |---------------->| 2. |<--------------->|<---------->| 3. |--------------------------->| 4. |<---------------------------| 5. |<----------------| 1. POST to http://example.com/foo/bar.cgi 2. Client is not authenticated, so do authentication 3. Once validated, send request to server (X-Remote-User: {userid}) 4. Process request, send response 5. Forward response to client I need to know how to configure IIS to do the automatic authentication of the user using AD, and then to proxy the request to the actual server, sending the userid in the X-Remote-User HTTP header.

  Read the article

• Mongrel Cluster on Ubuntu Server Karmic

  - by trobrock

  I am trying to get mongrel cluster working on my Ubuntu Server Karmic box in preparation to setup Capistrano. I've been trying to get the two to work all day and finally decided to completely remove Capistrano and see if I can just get Mongrel Cluster to work. I ran this to install mongrel cluster: gem install mongrel mongrel_cluster Everything installed fine, when I change into my app's directory... # mongrel_rails -bash: mongrel_rails: command not found I can run it from its install location: # /var/lib/gems/1.8/bin/mongrel_rails Usage: mongrel_rails <command> [options] Available commands are: ... It lets me build the cluster configuration file fine, but when I run the clister:start command: # /var/lib/gems/1.8/bin/mongrel_rails cluster::start starting port 8000 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8000 -P tmp/pids/mongrel.8000.pid -l log/mongrel.8000.log starting port 8001 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8001 -P tmp/pids/mongrel.8001.pid -l log/mongrel.8001.log starting port 8002 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8002 -P tmp/pids/mongrel.8002.pid -l log/mongrel.8002.log It seems it isnt calling it from the right directory after that command, what can I do to fix this? I tried setting the path previously when trying to set up Capistrano, but the path didnt stay set when Capistrano used ssh to run the commands.

  Read the article

• Xen domain migration locking problem

  - by brodie

  I am trying to live migrate a VM (domain) between two Xen servers. I have xen locking (xend-domain-lock = yes) configured with a ocfs2 shared storage between them. This locking is working fine. If I try to start up the VM on the secondary server it refuses to start (which is correct). The problem I am having is when trying to do live migration, it seems like it is trying to remove the lock twice. The first lock it removes is for "domain test", the second is for "migrating-test" which does not exist. Should their be a lock for this "migrating-test" VM? These are the relevant options in the xen config file: (xend-relocation-server yes) (xend-relocation-port 8002) (xend-relocation-address '') (xend-relocation-hosts-allow '') (xend-domain-lock yes) (xend-domain-lock-path /var/lib/xen/lock) This is the section of the log: [2010-06-10 10:45:57 14488] DEBUG (XendDomainInfo:4054) Releasing lock for domain test [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) SUSPEND shinfo 000c6ceb [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) delta 21ms, dom0 95%, target 0%, sent 57Mb/s, dirtied 173Mb/s 111 pages 4: sent 111, skipped 0, delta 6ms, dom0 100%, target 0%, sent 606Mb/s, dirtied 606Mb/s 111 pages [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) Total pages sent= 131295 (0.99x) [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) (of which 0 were fixups) [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) All memory is saved [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:474) Save exit rc=0 [2010-06-10 10:45:57 14488] INFO (XendCheckpoint:123) Domain 22 suspended. [2010-06-10 10:45:57 14488] DEBUG (XendDomainInfo:2757) XendDomainInfo.destroy: domid=22 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2227) Destroying device model [2010-06-10 10:45:58 14488] INFO (image:567) migrating-test device model terminated [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2234) Releasing devices [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2247) Removing vif/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:1137) XendDomainInfo.destroyDevice: deviceClass = vif, device = vif/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2247) Removing vkbd/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:1137) XendDomainInfo.destroyDevice: deviceClass = vkbd, device = vkbd/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2247) Removing console/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:1137) XendDomainInfo.destroyDevice: deviceClass = console, device = console/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2247) Removing vbd/51712 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:1137) XendDomainInfo.destroyDevice: deviceClass = vbd, device = vbd/51712 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:2247) Removing vfb/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:1137) XendDomainInfo.destroyDevice: deviceClass = vfb, device = vfb/0 [2010-06-10 10:45:58 14488] DEBUG (XendDomainInfo:4054) Releasing lock for domain migrating-test [2010-06-10 10:45:59 14488] ERROR (XendDomainInfo:4070) Failed to remove unmanaged directory /var/lib/xen/lock/b01515ae-9173-03cb-0cb7-06f3dfbede8b.

  Read the article

• Network Load Balancing, intermittent port problem on Windows Server 2008

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem on a Windows Server 2008 NLB. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• Unable to access network resources through VPN

  - by fbueckert

  I'm currently attempting to connect one of our computers in the office to a client VPN. My development machine is running Windows 7, and can connect and see resources just fine. The problem computer is running Windows XP. They're both within the same network. Using the same credentials at both computers, the VPN connection (using the built in Windows network connections) works just fine. So far, so good. An IP address is assigned, and comparing both machines shows they're still in the same subnet. The problem is that the XP machine cannot see ANY of the computers in the client network. I tried a tracert to a target machine on the Windows 7 box, and the first item that comes up is the .0 address. Pinging it gives responses. Trying it on the Windows XP machine, however, comes up with just timeouts. Trying to trace to www.google.com allows the address to resolve (probably part of the cached resolutions), but results in just timeouts. I double-checked to make sure that the Windows firewall was not on, and trying to open the settings brings up a notification that the firewall service wasn't running, which leads me to believe that it's definitely not on. From my best guess, I've managed to connect the XP machine to a black hole of some sort. There's obviously something strange going on, but I'm not sure where I should be looking.

  Read the article

• Cannot connect to windows server by name over vpn connection

  - by ErocM

  I have a rented dedicated windows server on a public ip that is acting as a SQL Server and VPN server. I need to connect to this server via computer name to get replication in place. I cannot use an ip address due to this issue: So, due to this, we are going the VPN route. That is my primary issue: After I am connected to this server's vpn, I can connect to SQL Server using the ip address but I cannot connect by the computer's name as you can see below... Right now, there is no hardware firewall on it since I had it removed to test this issue. I am running Windows 2008 Enterprise Server as the VPN server. I am not sure if the route print will help any from the workstation trying to connect but here is the info: IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 10.0.0.0 255.0.0.0 10.0.0.1 10.0.0.2 21 10.0.0.2 255.255.255.255 On-link 10.0.0.2 276 Any other info needed? Thanks for the help! ========= CLARIFICATION ON A FEW THINGS #1 ========= This is the server's info: This is the workstation that is trying to connect: I connect to the server via "Control Panel\Network and Internet\Network and Sharing Center\Connect or Disconnect" You can see here that I am connected: ========= CLARIFICATION ON A FEW THINGS #2 ========= I've tried to connect directly to the Sql Server as I did above but with the computers name and I couldn't get to it. Here I am trying to net view it from the workstation and it couldn't find it:

  Read the article

• FastGate A20 Line And Himem.sys Issue With Updating BIOS

  - by Boris_yo

  I have been persistent with a thought to perform my first BIOS update ever through MS-DOS but have been postponing this task until today. Despite people telling me any bootable ISO will do it either through CD-ROM or RAMDRIVE, I am still having problems. First is the problem with CD-ROM driver trying to make it work with 4 driver files (cd1.SYS, cd2.SYS, cd3.SYS, cd4.SYS) as well as starting RAMDISK proved to be failure: CD-ROM XMS Allocation Error RAMDISK XMS Allocaton Error (X: and R: drives not working) This A20 line seemed to be the obstacle which then after a couple of searches pointed me to this article on Microsoft website. It seems that FastGate is the culprit which takes over A20 line and conflicts with himem.sys which should be handling it causing the driver to be unable to allocate memory resources. Albeit article suggests 2 workarounds which is disabling FastGate option or adding switch, I read that the former workaround could cause problems which involves later tinkering BIOS, disabling shadow copy etc. while the latter workaround can just hang system as stated in the link above. I assume it just hangs the boot process from image file though. Summing up the above, I am cautious and think it is risky to follow both workarounds because disabling FastGate or trying adding switch by trying available switches from 1-14 or 16, could crash the BIOS update process by itself. I could do this without the need for himem.sys with bootable USB thumbdrive by making it to be seen as USB-HDD, but some time ago I read that it is never a good idea to update BIOS from hard drive so even thought it is simulation, who knows... Maybe it will deactivate hard drive in the middle of the BIOS update process or even USB thumbdrive per se? One forum discussion was about updating BIOS and somebody suggested to not load himem.sys for some reason, but now that I think of it, what if BIOS update needs upper memory?

  Read the article

• SQL Server Offsite Backups

  - by Eric Maibach

  We have about !TB of SQL Server databases, and these databases generate about 200GB of data changes each day. Up to this point we have been doing Weekly full backups, daily diff backups, and hourly transaction log backups. The full and diff backups are backed up to tape and taken offsite each day. We have been trying to move away from tapes, and our IT department purchased a Barracuda Backup device that backups up data and then sends it offsite using our internet connection. I have been trying to get this to work for our SQL Server backups, and have ran into a number of problems. I normally like to just use SQL Server to perform backups instead of trying to use a agent, so that is what I tried first. However the Barracuda device was not able to dedup these files very well, so it ended up being to much data to try to send offsite and to archive. I then tried installing the Barracuda agent and using it to backup the SQL Server databases. However the problem I am having there is that on some of the database servers I also have files that need backed up, and I cannot find a way to create seperate backup schedules for the file backups and the SQL Server backups. Barracuda only does full or transaction log backups. So if I want to do hourly transaction log backups I end up doing a file system backup every hour (which is not good), or if I only schedule the backups to run once a night I either have to do a full backup every night, or only do a transaction backup once a day. None of these scenarios are good options. My question is, how is everyone else getting their large SQL Server database backups offsite. Are you just using tape, or have you found a offsite backup device that works well? Is anybody else using Barracuda to backup their SQL Server databases? If you do, then how do you have it setup?

  Read the article

• Cannot properly read files on the local server

  - by Andrew Bestic

  I'm running a RedHat 6.2 Amazon EC2 instance using stock Apache and IUS PHP53u+MySQL (+mbstring, +mysqli, +mcrypt), and phpMyAdmin from git. All configuration is near-vanilla, assuming the described installation procedure. I've been trying to import SQL files into the database using phpMyAdmin to read them from a directory on my server. phpMyAdmin lists the files fine in the drop down, but returns a "File could not be read" error when actually trying to import. Furthermore, when trying to execute file_get_contents(); on the file, it also returns a "failed to open stream: Permission denied" error. In fact, when my brother was attempting to import the SQL files using MySQL "SOURCE" as an authenticated MySQL user with ALL PRIVILEGES, he was getting an error reading the file. It seems that we are unable to read/import these files with ANY method other than root under SSH (although I can't say I've tried every possible method). I have never had this issue under regular CentOS (5, 6, 6.2) installations with the same LAMP stack configuration. Some things I've tried after searching Google and StackExchange: CHMOD 0777 both directory and files, CHOWN root, apache (only two users I can think of that PHP would use), Importing SQL files with total size under both upload_max_filesize and post_max_size, PHP open_basedir commented out, or = "/var/www" (my sites are using Apache VirtualHosts within that directory, and all the SQL files are deep within that directory), PHP safe mode is OFF (it was never ON) At the moment I have solved this issue with the smaller files by using the FILE UPLOAD method directly to phpMyAdmin, but this will not be suitable for uploading my 200+ MiB SQL files as I don't have a stable Internet connection. Any light you could shed on this situation would be greatly appreciated. I'm fair with Linux, and for the things that do stump me, Google usually has an answer. Not this time, though!

  Read the article

• Subdomains not working with virtual hosts on apache2 ubuntu

  - by cy834sh4rk

  I'm trying to set up a subdomain on my ec2 account but can't figure out what's going on. I've looked for a few hours and haven't been able to find an answer :-/ I'm trying to set up a subdomain using virtual hosts but no matter what I try the browser can't find the subdomain :-( I have the following vhosts files set up: apache2/sites-available/mysite (this site currently works) <VirtualHost *:80 ServerName mysite.com ServerAdmin webmaster@localhost DocumentRoot /home/sites/mysite <Directory /home/sites/mysite Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory ErrorLog ${APACHE_LOG_DIR}/mysite-error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/mysite-access.log combined </VirtualHost apache2/sites-available/red (this is the subdomain I'm trying to set up) <VirtualHost *:80 ServerName red.mysite.com ServerAdmin webmaster@localhost DocumentRoot /var/www/red <Directory /var/www/red Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory ErrorLog ${APACHE_LOG_DIR}/red-error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/red-access.log combined </VirtualHost Apache mod_rewrite is enabled. I've enabled both sites using a2ensite and I make sure I restart apache every time I make a change. /etc/hosts 127.0.0.1 localhost 127.0.0.1 mysite.com 127.0.0.1 red.mysite.com Any help would be appreciated. Thanks!

  Read the article

• Rename Active Directory domain following Windows 2000 -> 2008 migration.

  - by ewwhite

  I'm working with a site that needs an internal DNS domain rename. It currently has a DNS name of domain.abc.com and NT name of ABC. I'm trying to get to a DNS name of abctrading.com and NT name of ABCTRADING. Split DNS would be used. The site originally ran from a single Windows 2000 domain controller hosting AD, file, print, DHCP and DNS services. There was no Exchange system in the environment. The 50 client PCs are all Windows XP with a handful of users using roaming profiles. All users are in a single OU and there are no group policy/GPOs. I'm a Linux engineer, but have been trying to guide another group of consultants to reach a more suitable setup. With the help of this group, we were able to move the single Windows 2000 system to a set of Windows 2008 R2 servers separated into domain controller and file/print systems (virtualized). We are also trying to add an Exchange 2010 system to this mix. The Windows 2000 server was demoted and is no longer in the picture. This is the tricky part, as client wants the domain renamed and the consultants aren't quite sure how to get through it without another 32-40 hours of testing/implementation. THey say that there's considerable risk to do the rename without a completely isolated test environment. However, this rename has to be done before installing Exchange. So we're stuck at this point. I'd like to know what's involved in renaming the domain at this point. We're on Windows Server 2008. The AD is healthy now. Coming from a Linux background, it seems as though there should be a reasonable path to this. Also, since the original domain appears to be a child/subdomain, would that be a problem here. I'd appreciate any guidance.

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• Can't upgrade NVIDIA GeForce 310M display driver on Acer Aspire 5745PG

  - by Emerson

  I've been for days already trying to update my video driver. I have an Acer Aspire 5745PG with a "NVIDIA GeForce 310M" board, and I was trying to run Sony Vegas video editor with Boris Continunn plugins. It happened that some of the plugins, like BCC Text Extrude wouldn't work, showing the message "Insufficient depth resolution to run Blue". I then read somewhere that updating the display driver would do the trick. That was when my nightmares started, I lost already good 3 nights trying to sort this out, without success :( The display driver that was before (and that I current have after restoring) was the version 8.16.11.8997. First thing I tried was downloading the 8.17.12.6619 driver directly from Acer, which was shown as the latest version from Acer website: http://support.acer.com/product/default.aspx?modelId=2466 Running it would say "Diver Package Failure - Setup failed to read the required Display Driver to be used with this package" I then tried directly the NVIDIA own driver, which the latest was version 296.10: http://us.download.nvidia.com/Windows/296.10/296.10-notebook-win7-winvista-64bit-international-whql.exe That gave me similar error message :/ So after some researching I found out that some people had the same issue and they had to change the configuration file to allow the installer to recognize this NVIDIA board: http://forums.nvidia.com/index.php?showtopic=222904 That topic said to look for the "Device Instance Id" property of the "NVIDIA GeForce 310M" display , which I couldn't find, instead I found the "Hardware Id", which seemed to be the right one. I followed the instructions and changed the inf file first for the Acer installation, and after for the NVIDIA own driver. It actually managed to go ahead with the installation in both instances, but the only thing I got was a black screen, while the computer still apeared to be running fine. I had to hard reset, and then it would come back with generic vga driver. I could only get my display back using the recovery function. I imagine thousands of this notebook was sold, and it can't have its driver updated?? Could someone help me with this?? Thanks Echo

  Read the article

• FTP issues with Windows 2003 box and Filezilla

  - by vanhornRF

  We've set up a Windows 2003 server with IIS 6 and the FTP is Filezilla. I'm not a sys admin by any means and neither is my other developer. I'm trying to connect to FTP on a Mac with a Cyberduck FTP client. I'm running OSX 10.6.3. The problem is that I can connect to the FTP address, but when I do it will hang for a minute or two trying to list the directories. This address is pointed to the webroot folder so it's only trying to list the pertinent folders for the site we're working on. Eventually after a minute or two it will go through and list everything and then if you try and open a file or another folder, it will hang again and then eventually list the folders. My question: Is there some stupid default setting we're missing? Is this a common occurrence? Like I said I'm not a sys admin at all and I'm sure I'm missing some valuable questions for anyone that reads this, so please fire away if you can help and you need more info, I'll do my best to provide it. Thanks!

  Read the article

• Repairing hard disk when Windows installation disk won't boot

  - by Echows

  I'm trying to recover some data from a faulty hard disk with Windows installed on it (on which Windows won't even boot). I have tried so far: Booting to Ubuntu live USB stick and running ntfsfix (didn't work) Trying to mount the broken partition when running Ubuntu from usb stick (doesn't mount) Running photorec image recovery tool from live Ubuntu (it found some stuff but not the images I was looking for) Now as a last resort I got myself a Windows installation on a USB stick so that I can try fdisk, but the installer doesn't work. The loading screen shows up and then the installer crashes. The installer works fine on other computers. I suspect that the installer is trying to read the hard drive to see if there's something there but when it can't read one partition, it crashes. On Ubuntu, I can mount other partitions except the one I'm interested in so at least the hard drive is not completely dead. So the question is, what options do I have left? To be more specific, my goal is to recover some images from the faulty ntfs-partition on the hard drive. Other than that, I don't care about the contents of the hard disk.

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >