Search Results

Search found 9730 results on 390 pages for 'restart programs'.

Page 105/390 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Wireless keeps shutting off in Windows 7

  - by Nathan Adams

  I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• How to set an executable white list?

  - by izabera

  Under Linux, is it possible to set a white-list of executables for a certain group of users? I need them to be unable to use, for example, make, gcc and executables on removable disks. How can this be done? Edit, let me explain better. I'm dealing with a high school IT system, young geeks that (during the lessons) want to play, surf the net, damage those computer however they can. The major step to achieve this goal was to remove the system they're familiar with and install Ubuntu in all the computers. This actually works quite well, but recent events proved that this is not enough. I want to allow them to execute certain safe programs, like Open Office, and to deny any other program, whether it is preinstalled software, something they carry in usb drives, a downloaded program or a script they program on site. It's possible to remove the 'x' permission on any file on the pc, but of course it would be impractical. Furthermore, they would be able to run anything they download. I thought the best solution would be to make a white-list of safe programs and to deny anything else, but I don't really know how to do it. Any idea is helpful.

  Read the article

• Optimizing Apache for large file serving

  - by D_Guy13

  I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

  Read the article

• Linux security: The dangers of executing malignant code as a standard user

  - by AndreasT

  Slipping some (non-root) user a piece of malignant code that he or she executes might be considered as one of the highest security breaches possible. (The only higher I can see is actually accessing the root user) What can an attacker effectively do when he/she gets a standard, (let's say a normal Ubuntu user) to execute code? Where would an attacker go from there? What would that piece of code do? Let's say that the user is not stupid enough to be lured into entering the root/sudo password into a form/program she doesn't know. Only software from trusted sources is installed. The way I see it there is not really much one could do, is there? Addition: I partially ask this because I am thinking of granting some people shell (non-root) access to my server. They should be able to have normal access to programs. I want them to be able to compile programs with gcc. So there will definitely be arbitrary code run in user-space...

  Read the article

• Why is only one Excel spreadsheet crippled, but others are fine?

  - by Dallas

  I have an inherited spreadsheet that I really don't want to rebuild at the moment. It's a simple small workbook that is small (< 200 rows that don't even reach to AA) and does nothing more than calculate some totals within the same worksheets. No macros, no external data sources, nothing beyond basic formatting of dates, numbers and strings. I see importing data from CSV/text has created many many workbook connections over time, but even if I delete them all (there were hundreds) it makes no difference in performance. Even clicking to simply change focus from cell to cell takes 10+ seconds, adorned by the spinning cursor and (Not Responding) appending to the title bar and the application locking up. The program seems to "recover" every time, but efficiency of editing this file is obviously seriously handicapped. All other files seem fine in Excel, and other programs have no apparent performance issues. I see Excel is chewing up CPU but I'm not sure how to narrow down what process or service is "clashing" with Excel. I tried the same file on other computers and performance is fine. If I turn off all start-up services and run only Excel, performance is restored... until I start using other programs and then it bogs down again. At this point, I would entertain almost any idea, theory or suggestion that helps pinpoint, solve or work around the issue.

  Read the article

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• Enable bitlocker an save key to share

  - by user273694

  I have searched all over the web but cannot find a complete answer to this: How to enable Bitlocker on a laptop with TPM, and store a file with the Bitlocker recovery key and TPM password by USING THE manage-bde command line tool. The file should be the same as when created in the Bitlocker manager UI. I DO NOT want to save to AD. The same question was asked here but was not answered correctly. The goal is to write a script to be used with an endpoint manager. I have tried the following: manage-bde -on C: Works fine, but does not create or save a key. manage-bde -on C: -rk C:\myfolder\ and manage-bde -on C: -RecoveryKey C:\myfolder\ -rp The output from the last two methods state that a key has been saved to c:\myfolder and so on, but that is not the case. It also says that I have to: Save the password in a secure location Insert a USB flash drive with an external key file into the computer. Restart and run hardware test type "manage-bde -status" to check if the hardware test succeeded After a restart, I get an error saying that Bitlocker could not be enabled because the bitlocker startup key or recovery kpassword cannot be found on the USB device.... C: was not encrypted. Why am I asked to insert a USB?? I simply want to encrypt the hard drive and save the recovery information to a file automatically. Is that too much to ask? Help please!

  Read the article

• Opera's problem with magnet-links

  - by Dmitriy Matveev

  I've encountered following problem while using Opera web browser: When I click on a magnet link on some web page like magnet:?xt=urn:tree:tiger:CXW6MJFRNOEFU2STCBWWOIYZLVCR2FTR37SQCXY&xl=352342016&dn=ER%20-%207x16%20-%20Witch%20Hunt.avi Opera is asking me if I want to open that link with my DC++ client. If I click 'Yes' button then my DC++ client is correctly "opening" the clicked magnet link and performing some action on it. There is also an option "Do not show this dialog again" in Opera's dialog, but it doesn't seem to be working correctly. If I check that option before answering 'Yes' and then click on other magnet link of the same kind the Opera will again ask me about how to open new link. I haven't found protocol association in 'Control Panel Default Programs Set Associations' part of my Windows Vista settings, but if I paste magnet link in "Run" dialog then Vista will handle that link perfectly. I've tried to find out how to manually set protocol association in Opera and found 'Programs' page of browser's advanced settings. There I discovered that instead of storing protocol to application associations Opera tries to store per-link associations (There are several entries with exact links as they was on web page as value of protocol field). If I click on the links which are already stored in Opera's protocols associations browser will ask me about them again. I haven't found any information on how to resolve this problem on the internet, maybe someone on this site will be able to help me.

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• Full-text search locks up database - error 0x8001010e

  - by Stewart May

  Hi We have a full-text catalog that is populated via a job every 15 minutes like so: ALTER FULLTEXT INDEX ON [dbo].[WorkItemLongTexts] START INCREMENTAL POPULATION We have encountered a problem where the database containing this catalog locks up. There are a couple of scenarios, we either see the job execute and the process hang with with a wait type of UNKNOWN TOKEN, or we see another process hang with a wait type of MSSEARCH. Once this happens the job continues to run but informs us that the request to start a full-text index population is ignored because a population is currently active. Looking in the full text log files we see the following error each time these problems occur: 2010-04-21 08:15:00.76 spid21s The full-text catalog health monitor reported a failure for full-text catalog "XXXFullTextCatalog" (5) in database "YYY" (14). Reason code: 0. Error: 0x8001010e(The application called an interface that was marshalled for a different thread.). The system will restart any in-progress population from the previous checkpoint. If this message occurs frequently, consult SQL Server Books Online for troubleshooting assistance. This is an informational message only. No user action is required."'' The only solution is to restart the SQL Server service and then the full text service. This is now occuring on a daily basis now so any help would be appreciated.

  Read the article

• MySQL fault linked to windows shutdown failure?

  - by Roy

  As far as i understand my computer is experiencing a strange coincidence (hopefully it isn't and somebody can enlighten me). Basically i shut down my laptop (Windows 7) (at 17.20, today, to be precise) successfully (and so also did XAMPP and its included components). However upon starting my laptop up again in the last hour i noticed that the MySQL module service in my xampp control panel was not coming on (just a big red tick; incidentally everything else was working fine). Now, i had the exact same problem about two weeks ago, whereby i just reinstalled xampp and got it working again. But rather than doing this straight away i thought i would just restart my laptop first. However it won't restart (or shut down first) to be precise now. I can remember Windows wasn't shutting down properly the last time it happened (about two weeks ago). Just wondered if this coincidence pointed to any specific diagnostic as regards the problem with MYSQL? If so i would appreciate greatly any help. Otherwise sorry for wasting your time.

  Read the article

• ssh hangs on "Last login" line

  - by Pavel H

  This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

  Read the article

• File sharing problem on Windows Server 2003 x64

  - by O. Askari

  Hi, We have a customer that hosts our .NET application server on Windows Server 2003 x64. The problem is, its file sharing gets totally disabled after about 10-30 minutes. The only way to re-enable it is to restart the server but the same thing happens again after each restart. This server contains SQL Server 2005 Enterprise, .NET Framework 3.5 and our .NET based application server. We haven't had such a problem with any other customer before so we asked them to prepare another server to deploy our application on it. We installed our application server on the new machine and let SQL Server remain on the old one. Unfortunately the same problem happened to the new machine too. Now the old machine works only as database server and the new one works as application server but both of them have the same file sharing problem. File sharing on both machines doesn't get disabled on the same time but it eventually happens to both of them. I wonder why is this happening and how to find the reason to this problem. Any suggestion or solution is much appreciated.

  Read the article

• realtek lan driver problem - win 7

  - by tango _123

  Hi, my new notebook (ACER TM 8371) with Win 7(x32) professional as OS, has strage behaviour with respect to LAN. when I plug or unplug my charger cable, or my notebook goes in stad-by, or just a do nothing, the netwrok connection is lost. All the energy savings functionbality have been in-activated. if i check the network adapter information, it says "a network cabel is unplugged or corrupted", but it is not true.....the cable is in and it is not corrupted (i tried several which works on other machines). if a tried to di-habilitate and hence re-habilitate, it allows di-habilitation and not to further re-habilitate (it says "no driver for the network card" are available). in some cases, also, the driver disappears (i cannot see it anylonger). if i restart the notebook, everything comes back to normality, but.....today in 3 hours i had to restart 6 times!!! can anyone help me? win 7 says the driver is the last one, so no need to update it. here are some techinical information aboiut network card and driver: Name [00000015] Realtek PCIe GBE Family Controller Adapter type Ethernet 802.3 Product type Realtek PCIe GBE Family Controller Installated YES ID device PNP PCI\VEN_10EC&DEV_8168&SUBSYS_02831025&REV_02\4&266E4C4F&0&00E2 last reset 20/11/2009 11:27 Index 15 Service name RTL8167 I/O Port 0x0000FF00-0x0000FFFF Memory address 0xE2500000-0xE2500FFF Memory address 0xE1400000-0xE140FFFF IRQ Channel IRQ 18 Driver c:\windows\system32\drivers\rt86win7.sys (7.3.522.2009, 164,00 KB (167.936 Byte), 28/08/2009 22:12)

  Read the article

• Locked out of our Comcast Business Gateway for seemingly no reason

  - by Tyler

  A little backstory... Last fall we migrated our ISP from AT&T to Comcast at one of our offices. At that time, we received a new modem/router from Comcast and we configured everything to our liking. We've never really had very many issues with the router aside from having to restart it every once in a while. Here's the problem... About three months ago I changed the password on the router from the default. After that, I logged into the router several times to make changes with no issue. During May I logged into the router to add two new static routes, no problems. A week ago, I tried to log into the router and could not. I tried the non-default password that I changed it to, the default, anything and everything I could think of and no luck. I restarted the router on Monday thinking it may just be locked up, but after the restart it would still not let me log in. This router is at our other office about 2 hours from here and I want to avoid having to drive down there and reset to factory defaults, reconfigure, etc. Any ideas?

  Read the article

• Heavy write to Galera cluster - table locked, cluster practically unusable

  - by Joe

  I set up Galera Cluster on 3 nodes. It works perfectly for reading data. I have done simple application to make some test on the cluster. Unfortunately I have to say that the Cluster fails totally when I try to do some writing. Maybe it can be configured differently or I do sth wrong? I have a simple stored procedure: CREATE PROCEDURE testproc(IN p_idWorker INTEGER) BEGIN DECLARE t_id INT DEFAULT -1; DECLARE t_counter INT ; UPDATE test SET idWorker = p_idWorker WHERE counter = 0 AND idWorker IS NULL limit 1; SELECT id FROM test WHERE idWorker = p_idWorker LIMIT 1 INTO t_id; SELECT ABS(MAX(counter)/MIN(counter)) FROM TEST INTO t_counter; SELECT COUNT(*) FROM test WHERE counter = 0 INTO t_counter; IF t_id >= 0 THEN UPDATE test SET counter = counter + 1 WHERE id = t_id; UPDATE test SET idWorker = NULL WHERE id = t_id; SELECT t_counter AS res; ELSE SELECT 'end' AS res; END IF; END $$ Now my simple C# application creates for example 3 MySQL clients in separate threads and each one executes the procedure every 100ms until there is no record where column 'counter' = 0. Unfortunately - after about 10 seconds sth is going bad. On servers there is process 'query_end' that never ends. After that - you cannot make update on the test table, MySQL returns: ERROR 1205 (HY000): Lock wait timeout exceeded; try restarting transaction . You cant even restart mysql. What you can do is to restart server, sometimes whole cluster. Is Galera Cluster so unreliable when you do massive concucurrent writing/updates? Hard to believe.

  Read the article

• Read non-blocking from multiple fifos in parallel

  - by Ole Tange

  I sometimes sit with a bunch of output fifos from programs that run in parallel. I would like to merge these fifos. The naïve solution is: cat fifo* > output But this requires the first fifo to complete before reading the first byte from the second fifo, and this will block the parallel running programs. Another way is: (cat fifo1 & cat fifo2 & ... ) > output But this may mix the output thus getting half-lines in output. When reading from multiple fifos, there must be some rules for merging the files. Typically doing it on a line by line basis is enough for me, so I am looking for something that does: parallel_non_blocking_cat fifo* > output which will read from all fifos in parallel and merge the output on with a full line at a time. I can see it is not hard to write that program. All you need to do is: open all fifos do a blocking select on all of them read nonblocking from the fifo which has data into the buffer for that fifo if the buffer contains a full line (or record) then print out the line if all fifos are closed/eof: exit goto 2 So my question is not: can it be done? My question is: Is it done already and can I just install a tool that does this?

  Read the article

• Configure X connections over TCP without using an X connection

  - by Darren Cook

  I want to run a GUI application on a remote machine I only have ssh access to. I don't need to, or want to, see the GUI window. (I know I could use something like ssh -C -X remote_server if I wanted the GUI to be on my client.) I know X is running on the remote machine, as ps shows this: root ... /usr/bin/Xorg :0 -br -audit 0 -auth /var/gdm/:0.Xauth -nolisten tcp vt7 I set DISPLAY=:0.0 but I then get "Xlib: connection to ":0.0" refused by server" when I try to use it. At Get remote x display working in linux without ssh tunneling and Xserver doesn't work unless DISPLAY=0.0 I see the advice to use gdmsetup to allow X to listen on TCP. But, gdmsetup is a GUI application! And trying to run it over ssh -X did not work ("X11 connection rejected because of wrong authentication"). So, is there a text file I can edit to remove -nolisten? And, after editing it, how do I safely restart X, remotely? (There is other stuff running on this machine, so requesting a reboot is possible, but undesirable.) If not, should gdmsetup be able to run over ssh and I should persevere in that direction? UPDATE: I had to do the ssh -X session as root (ssh as a normal user, then sudo or su, does not work.) So, I did the edit with gdmsetup. I then restarted X with gdm-restart. I've also done xhost + from that ssh -X session. The ps line no longer shows the -nolisten tcp part. But still no luck connecting to it, with either DISPLAY=:0 or DISPLAY=localhost:0

  Read the article

• Can I install windows on an SSD and access data from my old windows HDD?

  - by nzifnab

  I purchased new computer components, switching my hardware from AMD and Radeon to Intel and Nvidia. I kept components from my old computer like the powersupply and two HDDs. Everything appeared to install correctly and the system booted into the BIOS just fine (after a brief snafu with the CPU fan). My goal was to use the two harddrives and just be able to turn on the computer and load up my old windows install with all the files, programs, and documents. I expected to have to call Microsoft to re-register the windows install for the new hardware (since I had to do that last time I upgraded w/ the same windows version). When the computer attempts to boot into windows it briefly flashes a bluescreen and then restarts. System recovery gives a message something like "BadDriver Failover" something something. I assume this is because it's trying to use amd drivers for an intel chipset (or something...?) and I've been as-yet unsuccessful in getting it to boot into my old windows partition. SO! I decided eff it, maybe I'll go visit my nearest Micro Center and buy a 200 GB SSD, install windows onto that, and then... be able to access just the contents of both of my other harddrives? I don't intend on running any of the programs but there were some saved files I would like to salvage from the 500 GB harddrive, The 1.5 TB harddrive only had files on it, no OS or applications so I'd also expect to still be able to access it. Is this possible? Can I install the SSD and only format/install windows onto it and still access the contents from my two transferred-over drives?

  Read the article

• Microphone doesn't work

  - by mandy

  I'm having a trouble with my built in microphone. Even if I use headphone with mic, it doesn't really work. The weird thing is, if I clap the green lines of the speaker icon jumps, but if I speak it doesn't. I have also tried some recordings, but I can not hear myself and adjusting the volume didn't help at all. I tried to restore it, still no change. I have updated it in the device manager, but it said there that it's up to date and the devices are working properly. Until I decided to recover the whole system (wherein I pressed zero and switch on button) to my surprise, the settings became different, most programs were deleted, even my files. It's like it was formatted and I'm so sad that the mic was not fixed. I really don't know what to do now. My laptop model is Toshiba satellite m840. I want to it return to its settings/set up just before I Recover the system and bring back all the programs that we're installed and of course, most of all, to fix my microphone so I can use Skype again and other video calling application.. I hope someone could help me. Thanks a lot!

  Read the article

• Have .cmd in startup wait for system wide startup to run.

  - by Dan

  On a computer I'm not an administrator on, there is a startup file (.cmd file in C:\Documents and Settings\All Users\Start Menu\Programs\Startup) for all users. It does several things I don't like, so I have created my own .cmd file which I have placed in C:\Documents and Settings\[user]\Start Menu\Programs\Startup. I want my code to run after the system wide, because my program first undoes the network mappings the system wide file did, and then replaces it with my own network mappings. How can I make my program wait and start as soon as the system wide one is done? (I cannot remove or edit the system wide file). Thanks EDIT: The time that the system wide file takes to runs varies and I would like my file to run right after. The "If Exists" method seems a little to contingent since the system wide script can change or a file could be moved. I am hoping to give my script to a few of my coworkers, so hoping to have it work without me having to update anything. Also, being a linux guy, I don't know cmd code, so please write out any coding suggestions.

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• PassEnv does not find ENV variables

  - by quodlibetor

  I've got this /etc/profile.d/myfile.sh: export MYVAR=myval I also have a PassEnv MYVAR line in a <virtualhost> section of an apache conf dir. That lets me do things like: $ echo $MYVAR myval $ python >>> import os; os.getenv('MYVAR') 'myval' $ sudo echo $MYVAR myval $ sudo -i root# echo $MYVAR myval But then, despite that being the case I get: root# /sbin/service httpd restart /sbin/service httpd restart Stopping httpd: [ OK ] Starting httpd: [Mon Oct 22 14:44:02 2012] [warn] PassEnv variable MYVAR was undefined [ OK ] And all of my attempts to access MYVAR from within my wsgi scripts just don't work. Thoughts? Am I doing something obviously wrong? EDIT for more detail I've got a swarm of computers/VMs and a swarm of developers working on a swarm of projects. I need a simple central place to keep environment information, the most common is the "environment" (dev/stage/prod). The scheme that we've got (modifying *.wsgi programmatically) is turning out to be more fragile than we'd like. The main options that I see are: put things in the shell environment put things in other config files Getting things into the shell environment is the best, because we won't need to write yet more duplicated "what is my environment" code.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >