Search Results

Search found 3712 results on 149 pages for 'light hammer'.

Page 106/149 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• Where do I connect the HDD LED wires on my RAID adapter?

  - by Giffyguy

  I'm using a Promise FastTrak TX8660 with RAID 5. The manual (and Google) just doesn't seem to explain how exactly to connect a standard two-pin HDD LED wire to the eight available pins on the card. The Manual just says - To connect your LED, follow the following diagram: The card itself resembles the diagram: But it doesn't make any sense to me. All I have is a two-pin connecter for HDD LED on the front of my computer case. I don't need anything fancy like the fault LED or seperate indicators for each drive. I just want to be able to see when my RAID 5 array is working, that's all. I don't know what the "R" and "G" stand for, but my HDD LED wires are red and white. I tried connecting the red wire to the "R" pin and the white wire to the "G" pin, but that just makes the LED on the front of my case light up indefinitely, even when the computer is idle. Which pins am I suppose to connect the HDD LED header to for basic activity indication?

  Read the article

• Safe mode boot with no change on screen but ongoing hard disk activity - why?

  - by omatai

  I have a machine with a dying hard drive - bad sectors are starting to multiply :-( The first sign (24 hours ago) was that it had an unmountable boot volume. At this time, I tried booting to safe mode with command prompt, which worked, after which I rebooted normally and ran a chkdsk. It has since been working as well as I could expect, but slowly getting less reliable. So I scheduled another chkdsk on both partitions (C: - boot, D: - data), having freed up a lot of space on both partitions to give Windows a little more scope for repairs (hopefully?). I then rebooted. On reboot, it protested about the unmountable boot volume again, so I booted to safe mode. I got the same list of drivers loaded as yesterday, and then no change to the screen for the past 2 hours. However, I see a flickering hard drive indicator light - not always on, but seldom ever off. What is happening? Is the chkdsk that runs in safe mode one which produces nothing on the screen and so chkdsk could be doing its thing... or is Windows still trying (but failing) to boot into Safe Mode?

  Read the article

• Domino to Exchange 2007 (or 2010) Design Concerns?

  - by NickToyota

  Today we got the executive green light to proceed with changing from a Domino platform to Exchange. The business prefers Exchange for a messaging platform. (even though IMO IBM Domino is fine - if it aint broke, don't fix it but it was not my call). I have been put in charge of Domino to Exchange process goes smoothly as possible. I have also been told to put together costs for this project. I have some questions and concerns re: network design, licensing, costs: The current setup is as follows. 1 HQ office (100 users), 1 secondary office (50 users), 5 branch offices (under 10 users). 5 different email domains Windows Server 2003 functional level with a few 2008 R2 Servers Lotus Domino Notes Servers (one in each office) Ironmail Appliance Public Domino Web Mail server Majority G5+ Proliant Servers Domino Blackberry Enterprise license and server No VoIP phones What are the basic hardware requirements for Exchange 2007 or 2010? Can I simply purchase a single physical server? Will each office require an Exchange server or possibly additional servers (roles)? How is email routed to the smaller branch offices? Standard or Enterprise licenses? The business has been running Domino (messaging and application services) for over 10 years and also want Exchange to support email services, Blackberry, Outlook Web Access, possibly support for iPhone devices. Thank you Serverfault universe.

  Read the article

• Asus n61Ja notebook bios update

  - by zKs

  I wanted to update the bios, with an official bios update, from version 207 to 211. I didn't use winflash, I used easyflash in the bios. Everything seemed to be going okay; it deleted the old files, wrote the new ones, verified the new ones. Then it said: shutdown in/after 2 seconds and it shut down. Then nothing happened anymore. Power button completely unresponsive. The battery light was still on, and I'm not sure if I should've just waited... I didn't though, I thought I had to remove the battery, take the power off completely to be able to start it up again. So I'm wondering: what are my options here? My warranty expired and I don't really have the money to send it in and pay hundreds of bucks on repairs. Is there anything I can try? CMOS battery reset? Anything??? Please help me out! I would be very grateful :) ps. What was sort of odd btw, was that easyflash said something like that it was an unsigned bios and if I wanted to flash it anymore, if i wanted to 'force' it or something. It was with 100% certainty the correct update from the Asus.com support site, so I didn't take that 'warning' seriously.

  Read the article

• Toshiba Qosmio: Battery Stuck at 60%, does not Charges, PC can't power up, can't remain on with out

  - by Fellknight

  Just like the tittle says, now let me try to give some more detail about the symptoms; The battery is stuck at 60 percent (68% at the moment of this writing).When hovering over the battery icon in Windows 7 Home Premium x64 it reads:"68% available (plugged in, charging)", there's no x or any sing the OS is displaying any error. No matter how much time left connected to the AC adapter the battery doesn't charge, it seems however it continues to discharge at its normal rate when disconnected from the laptop (about 1% each 2 weeks). Now this last symptom is the one i find most strange it "seems" the laptop somehow isn't recognizing the battery because even with the remaining charge of 60%(ish) the laptop wont power up or remain on if disconnected from its AC adapter(if it's on and is unplugged it will immediately turn off). Meaning that even with the battery attached correctly in its right place is as if running the laptop with no battery at all. Toshiba's Utilities haven't detected anything strange (or anything for that matter) with the battery or the hardware. The laptop when in use is connected 90% of the time to a Belkin surge protector (like my 1TB EHD). The protector is working correctly (green light on) and the 1TB HD too, thus a power surge having damaged it's very unlikely. Thnx in advance

  Read the article

• ULogd2.x - Documents - IPFIX data generation

  - by Gomathivinayagam

  I would like to generate IPFIX data from the packets that are coming to my local system as part of experimentation. It seems ULogd is a good tool to do that. I am able to capture PCAP data. But there are very less documents available on ULogd2.x about IPFIX format data generation.(There are very few examples provided in ulogd.conf). Can you provide me any links that describes about how to generate IPFIX data using ulogd2.x? 1) What are the options available? I saw there is polling interval configuration. But I have no idea how does it work? 2) If I set hash_enable = 0, and uncomment the polling_interval value, I'm getting an exception as NFCT plugin requires hash table, evne though I have specified hash_buckets and hash_max_entries. Could you help on this? 3) In general, I would like to know how NFCT plugin works in ulogd2.x. I sent mail to ulogd mailing list, but there are no replies. Could you shed some light?

  Read the article

• Having trouble setting up my router

  - by indyK1ng

  I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

  Read the article

• Linux group permissions getting overwritten by owner

  - by Andy

  I am not a user of Linux, but I am encountering some permissions problems with it that I hope someone can shed some light on. Bit of background: A colleague of mine has a Linux box (running Debian I believe) with an SVN repository on it. The repository directory and files 'owner' is my colleauge. We are both members of a group called 'users'. He manages several projects both Linux and Windows apps, while I have one Windows app. For the Windows apps, we both use TortoiseSVN via an SSH link to commit/update. Performing the command 'ls -l' shows the repository files and folders on the Linux box to have the following permissions: -rwxrwx--- john users However, when my colleauge commits to the repository, the permissions change to: -rwxrwx--- john john This then means I get 'Permission denied' when trying to access the repository myself as it appears that the group permissions have been overwritten with only 'owner' permissions. To fix this, a 'chown -R' command is applied to the files/folders to set the permissions back to owner/group, but each time he writes to the repository, the issue repeats. I'm not sure if this is solely an SVN problem, or a more fundamental owner/group issue. Anyone any clue on how to stop this happening, or where to go and look? I'm trying to help out my colleague who is having some trouble resolving this issue. Apologies for the vague info, I hope I have conveyed the problem clear enough. Like I say, I am not a Linux user, I have only put down what I have managed to pick up from looking over his shoulder. Thanks for any pointers I can pass on!

  Read the article

• How does the LeftHand SAN perform in a Production environment?

  - by Keith Sirmons

  Howdy, I previously asked this ServerFault question: Does anyone have experience with lefthands VSA SAN The general consensus looks like it does not perform well enough for a production SQL server even at a light load. So the new question is, How does LeftHand's SAN perform on the HP or Dell dedicated Hardware boxes? We are looking at the Starter SAN with 2 HP nodes in a 2-way replication, 2 ESX servers hosting a total of 2 Active Directory server, 1 MS SQL server, 1 File Server, and 1 General Purpose Server for things like Virus Scan (All Microsoft Server 2005 or 2008). The reason I am looking at LeftHand is for the complete software package. I plan to have a DR site and like how the SAN can perform an Async Replication to the offsite location without having to go back to the Vendor for more licenses. I also like the redundancy built into the Network Raid architecture. I have looked at other SANS and found different faults with them. For example, Dell's EqualLogic: Found that although the individual box is very redundant in hardware, the Data once spanned across multiple boxes is not redundant, if a node goes down you have lost the only copy of the data sitting on that hardware (One thing is certain, all hardware fails... When? is the only question.). I have used an XioTech SAN as well.. Well worth the money BTW, but I think it is overkill for the size of the office I am targeting. The cost to get the hardware redundancy in the XioTech makes it a little out of reach for the budget I am working in. Thank you, Keith

  Read the article

• New Computer won't boot up

  - by Reggie

  I brought new components and put a computer together. I installed win7(32bit) and everything was working as it should. However my case came with two USB3 front ports I could not connect because of motherboard did not support USB3, so I swapped out the board for a new motherboad with USB3 connection. Now I put everything back together but it won't bootup. "Memory Ok" light stay on. Motherboad LED is on. There is power, all fans are on but I got no display. There is no activity in back of the systems, none of the peripheral connection in the back are working. I have tried the following but to no avail. Reboot multiple times Unplug power and plug the power back Reset the CMOS battery..let it stays out for 10 minutes or more. Unplug all peripheral device but no luck Reset memory..... nothing happen The only thing I did not do was remove the cpu...but I unplug everything else. Please help, thank you.

  Read the article

• IIS FTP error: 426 Connection closed; transfer aborted.

  - by Jiaoziren

  Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

  Read the article

• Linking to network shares from Sharepoint pages

  - by Russell C

  So the place I work decided to set up a Microsoft Sharepoint 2010 server for task management and I (as the lowly entry-level intern) have been tasked with "figuring it out." One thing that the end users really, really, really, want is the ability to link to network shares (that are readable by anyone who will be using sharepoint) from a Sharepoint web page. In order to do this, I have edited the HTML manually with several lines that look like the following: <a href="file://server/share">Server Share</a> This works (sometimes) but the link reported by Sharepoint is often wrong and editing pages that contain these links will mangle the code such that when I open it, the code no longer looks like what it did when I last hit save (breaking all those links). Obviously this is not sustainable. I've been told by coworkers that "It worked that way at the last place I worked" but I haven't found out how yet. Any ideas on how this would work or am I barking up the wrong tree? None of the knowledge searches I've done shed any light on the sitataion. Thanks for any help! -Russell P.S. It should be noted that the file option in an href tag ONLY works in IE (which is a real bummer since we mostly use Firefox).

  Read the article

• Configure Cisco Pix 515 with DMZ and no NAT

  - by Rickard

  I hope that someone could shed some light over my situation, as I am fairly new to PIX configurations. I will be getting a new net for my department, which I am going to configure. At my hands, I have a Cisco PIX 515 (not E), a Cisco 2948 switch (and if needed, I can bring up a 2621XM router, but this is my private and not owned by my dept.). The network I will be getting is the following: 10.12.33.0/26 Link net between the ISP routers and my network will be 10.12.32.0/29 where GW is .1 and HSRP roututers are .2 and .3 The ISP has asked me not to NAT the addresses on my side, as they will set it up to give 10.12.33.2 as a one-to-one nat to a public IP. The rest of the IP's will be a many-to-one NAT to another public IP. 10.12.33.2 is supposed to be my server placed on the DMZ, the rest of the IP's will be used for my clients and the AD server (which is currently also acting as a DHCP server in the old network config with another ISP). Now, the question is, how would I best configure this? I mean, am I thinking wrong here, I am expected to put the PIX first from the ISP outlet, then to the switch which will connect my clients. But with the ISP routers being on a different network, how will the firewall forward the packets to the other network, it's a firewall, not a router. I have actually never configured a pix before, and fortunately, this is more like a lab network, not a production network, so if something goes wrong it's not the end of the world, if though annoying. I am not asking for a full configuration from anyone, just some directions, or possibly some links which will give me some hints. Thank you very much!

  Read the article

• New XPC: No video, no ethernet link, but drive spins

  - by Mike Pennington

  I bought a Shuttle XPC SH67H3 with integrated video. I installed: An Intel i5 2450P 16GB DDR3 RAM A SATA hard drive from my old linux server that still is bootable I have both power connectors plugged into the motherboard. I realize that the Intel i5-2450P doesn't have video capabilities; however, the drive spins like it's doing something useful. It seems like I should get an ethernet link light when I fire this up. I plan to run this headless anyway, so it would be really nice if I could figure out how to run this without a video card at all. I know the IP address and login info for the linux install on the disk. I plugged in speakers, but get no bios beeps when I power it up. Shuttle's bios manual has nothing in there that indicates I should have problems in this configuration. My questions: Is there a reason that the missing video card would block usage of the ethernet port? Are there settings on the motherboard / bios I can change to get this working?

  Read the article

• Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

  - by neezer

  For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

  Read the article

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• WD my cloud 4th is Super Slow

  - by Saduser

  I am using a WD my cloud 4Tb and I have read other posts about users complaining about getting only 10Mb per second. My problem is that I am getting about 100kb/s to transfer a 125gb iPhoto library. Estimated time is 11 days to transfer this file. This is unacceptable. On the back of the WD cloud I am getting a solid green light and from what I read this means that I am on a gigabyte network. I have mac book pro running Mac OS Mavericks. I have tried 4 different cables and turned off my router firewall. I don't run anti-virus nor any firewall on the mac. Other things I have checked: direct connection to both router and WD cloud device. Tried wireless but it is even slower. Previously I was able to transfer a 55Gb iPhoto library in 14 hours which I felt was acceptable. I figured it would take approximately double the time to transfer the 125gb file but 11 days is ridiculous. Any other suggestions? Anything else I can check (how to check it) what is the bottle neck?

  Read the article

• iBook G4 has black screen on boot

  - by Jonathan Patt

  I have an old iBook G4 (A1054, 1.2 GHz) which has issues when it loses power or is shut off. If the battery drains—which happens quickly, as its remaining capacity is very low—it enters some sort of weird mode where it's not really awake (the screen is black, can't do anything) but it has no pulsing light indicating it's asleep either. The only way to exit this mode is to hold down the power button for ten seconds until it shuts off, and attempt rebooting it. Almost always, however, it makes the sound of the optical drive starting up, and then doesn't continue past that point. The screen doesn't come on, and things like resetting PRAM don't work. Occasionally a fan comes on loudly for a second or two. This sometimes seems to correspond with my pressing down on the rear-right casing, above the power jack. In the past, shutting it off, disconnecting it from power, removing the battery and waiting for 30 minutes would do the trick, but this time I have done that several times, letting it sit for up to several hours before retrying, to no avail. Any ideas?

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• OS X Hard drive recovery

  - by Adam

  I am trying to recover data from a bad Seagate 1TB hard drive in a 2010 iMac. One day the iMac wouldn't boot (stuck at gray screen on startup). I removed the hard drive from the iMac and connected it to a MacBook using a 3.5" HDD to USB adapter. The hard drive wouldn't mount but it did display in Disk Utility that that there were 2 partitions on the disk. I tried to run Disk Warrior and it showed thousands of errors but still wouldn't mount. At this time the hard drive only show one partition in Disk Utility. Next I tried putting the hard drive in a desktop PC and running Spin Rite - which then gave me several division overflow errors (even with running Spin Rite with a newer version of DOS). The SMART status on the drive reports that the drive has had failures and HD Tune referenced the drive had once hit 59 degrees celsius. Disk Utility gives me the following message when running a pair: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Overall, the hard drive spins up and sounds OK - there are no clicking noises but the hard drive won't mount and displays as a light gray "Macintosh HD" in disk utility. Any tips or advice on how to recover data on this drive would be GREATLY appreciated! Are there any other tools I can try before calling it quits on this drive? Thank you

  Read the article

• BIOS corrupted? How to proceed? Acer Travelmate 290

  - by dtlussier

  I have a older ACER Travelmate 290 (manufactured in 2002 or 2003), which I recently tried to upgrade to Ubuntu 9.10. After doing the upgrade process it appeared as if I had a problem with my x server configuration, as on the first reboot post-install I heard the Ubuntu startup sound, but had a black screen. I thought I would then reboot again to drop down into text-mode to trouble shoot the x configuration problem. However, when I tried rebooting, something went wrong and since then when I start up the machine I get absolutely nothing except the first hardware check (i.e. HDD light flashes, CD/DVD drive spins, etc.). Other than that the screen remains totally black and I have no HDD or processor activity at all. I have tried restarting it a number of time holding down all kinds of key combinations to try and coax it into the BIOS (if possible) with no luck. I have also tried putting in both a live Linux disc and a Windows install disk without any luck. With a disk in the drive it will spin for a few seconds and then stop. All this has lead me to suspect that the BIOS is somehow corrupt (not sure about the right terminology). I have tried putting a new BIOS image and installer program downloaded from ACER on a USB key to see if it will run when I start up the machine, but no luck. I'm not sure if this method of interacting/updating/flashing the BIOS will work outside of Windows/DOS as both OSs are mentioned kind of ambiguously in the documentation. I have also taken the laptop case apart and inspected the various cards and cannot find any obviously burned out components. I'm not sure how to proceed at this point in terms of components to try, or how to try and load a new BIOS image onto the board. Any advice here would be great, especially from those with experience with this particular line of laptops. Thanks!

  Read the article

• On Windows and Windows 7's Task Manager, why Memory is 1118MB Available but only 62MB Free? [closed]

  - by Jian Lin

  Possible Duplicate: Windows 7 memory usage What are the "Cached", "Available", and "Free" memory in the following picture (From Windows 7's Task Manager). If it is 1118MB Available, then why isn't it Free (to use)? As I understand it, if a bowl of noodle is available, that doesn't mean it is free... it may still cost $7. But what about in the Task Manager, when it is Available, it is also not Free? Does it cost $2 per MB? What about the "Cached"... What exactly is the Cached Memory? We may put some hard disk data in RAM and so we cache the data in RAM, for faster access (that's the operating system's job). So the Total Physical RAM is 6GB, what is the 1106 Cached? Cached in where? Caching physical RAM in ... some where? It is also strange that the Cached value is sometimes higher and sometimes lower than the Available value. Can somebody who is knowledgeable about this shred some light on these meanings?

  Read the article

• Windows, never "lose focus" of the current window

  - by Mazura

  I want the task bar to light up orange and never lose focus to anything. If I'm installing something and then go play a game at some point it will drop out to the finished instillation. Also, if installing multiple programs at once my 'next' button can all of sudden become "click here to install this crappy toolbar" of another program's install. Of course there are settings for some programs to not "lose focus" or "stay on top" but I really want windows to handle it. If its somehow an exe called say, Taskswtich.exe, I could possibly use Process Blocker however I'm assuming its part of a function call or some such. For XP I found this: How to disable auto focus of opened Windows applications? but what about Windows7? And this old post Preventing applications from stealing focus with a bunch of long answers that say "no". I'd appreciate this not being merged with a 4 year old question. I'd like to avoid 3rd party software. This is 2014, don't we know how to hack windows yet?

  Read the article

• Query Execution Failed in Reporting Services reports

  - by Chris Herring

  I have some reporting services reports that talk to Analysis Services and at times they fail with the following error: An error occurred during client rendering. An error has occurred during report processing. Query execution failed for dataset 'AccountManagerAccountManager'. The connection cannot be used while an XmlReader object is open. This occurs sometimes when I change selections in the filter. It also occurs when the machine has been under heavy load and then will consistently error until SSAS is restarted. The log file contains the following error: processing!ReportServer_0-18!738!04/06/2010-11:01:14:: e ERROR: Throwing Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Query execution failed for dataset 'AccountManagerAccountManager'., ; Info: Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Query execution failed for dataset 'AccountManagerAccountManager'. ---> System.InvalidOperationException: The connection cannot be used while an XmlReader object is open. at Microsoft.AnalysisServices.AdomdClient.XmlaClient.CheckConnection() at Microsoft.AnalysisServices.AdomdClient.XmlaClient.ExecuteStatement(String statement, IDictionary connectionProperties, IDictionary commandProperties, IDataParameterCollection parameters, Boolean isMdx) at Microsoft.AnalysisServices.AdomdClient.AdomdConnection.XmlaClientProvider.Microsoft.AnalysisServices.AdomdClient.IExecuteProvider.ExecuteTabular(CommandBehavior behavior, ICommandContentProvider contentProvider, AdomdPropertyCollection commandProperties, IDataParameterCollection parameters) at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.AnalysisServices.AdomdClient.AdomdCommand.System.Data.IDbCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.ReportingServices.DataExtensions.AdoMdCommand.ExecuteReader(CommandBehavior behavior) at Microsoft.ReportingServices.OnDemandProcessing.RuntimeDataSet.RunDataSetQuery() Can anyone shed light on this issue?

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >