Search Results

Search found 28300 results on 1132 pages for 'david back'.

Page 107/1132 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• DBAN Hangs at PCI (sysfs)

  - by David

  I'm running Derik's Boot and Nuke 2.2.6 (beta). When I get to a blue screen(Not BSOD) the following is printed. Derik's Boot and Nuke 2.2.6 (beta) is starting. Waiting for USB devices to register..........................done. PCI (sys) After that, it just sits there forever... Any advice, other than an older version of DBAN? I have gotten this version of DBAN to work on an older machine before.

  Read the article

• CPU installation

  - by David Oneill

  I'm in the midst of building a computer (this is my first time). When I first put the heatsink on the CPU, I was a little off center. Some of the thermal compound came off, so when I re-centered it, it isn't completely evenly distributed. So here's my question: how picky are CPUs in terms of how evenly the thermal compound is? Should I take it apart, clean it, and apply a new layer of compound? Or can I just keep an eye on the CPU temperature? (I'm not overclocking or anything, if that matters)

  Read the article

• ScreenOS MIP selection for outbound connections

  - by David Mackintosh

  Given a ScreenOS 6.3.0 firewall with this configuration: unset flow reverse-route clear-text set interface "ethernet0/0" zone "Trust" set interface ethernet0/0 ip 192.168.1.1/24 set interface ethernet0/2 ip 10.0.0.1/24 set interface ethernet0/2 mip 10.9.9.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set interface ethernet0/2 mip 10.8.8.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set route 0.0.0.0/0 interface ethernet0/2 gateway 10.0.0.254 ... (and assuming appropriate policies) is there a way to control which MIP the firewall selects for outbound connections initiated by 192.168.1.10? (presumably because I want the upstream 10.0.0.254 to do different things with the packet depending on what its source IP is). Update: OK, my scenario is this: I have two ISP uplinks, each giving me a different IP space. Each ISP will only route the IP space they have assigned me. So in order for the server to be reachable by both ISPs, I need two MIPs for the same server, one on each interface. Inbound traffic will work fine with the 'unset flow reverse-route clear-text' option in use. But for outbound (think an email server sending a message) I need a way to select an appropriate MIP depending on which outbound link I want the system to use, and I want this to be resiliant so that if the link the firewall prefers goes down overnight I don't have to manually flip something to keep the mail flowing. Basically I'm trying to avoid having to buy a link-balancer appliance (or two since I'll need a cluster). Is there a way to do this?

  Read the article

• Mac Joining Active Directory Still Prompts For Authentication

  - by David Potter

  My Mac is joined to an Active Directory domain. What I expected to see was the same ease of access to file shares and internal websites that Windows computers joined to the domain experience (i.e., no authentication needed; it just uses Windows Integrated Authentication). Instead I am asked for credentials each time I try to access those shares and protected websites (e.g. SharePoint). Is this normal behavior, or is something wrong with my Mac that it prompts me for my username and password for the domain when I access Windows file shares or intranet sites protected by NTLM/Kerberos? Machines include: MacBook Pros running Mountain Lion MacBook Pros running Lion MacServer running Lion Server

  Read the article

• Suse 12.3 cannot boot after a forced shutdown

  - by David Dai

  I was doing a system update using zypper update After a while the screen was filled with this message failed to start system logging service. and the system was not responding. I had to shutdown it by holding the power button. then I started the machine again, and selected to boot suse. Then I saw the fancy boot animation(some shiny big dots gathering to the center of the screen), then the screen just turned black and the monitor sayed "no signal". then I tried to boot into suse failsafe mode, which was fine. how can I investigate into this problem?

  Read the article

• Have rTorrent to move .torrent files

  - by David Alvares

  I am running rTorrent 0.9.2 and have configured it to move completed torrents to a different folder with this configuration line: system.method.set_key = event.download.finished,move_complete,"d.set_directory=~/done/;execute=mv,-u,$d.get_base_path=,~/done/" This is working fine, but I would like it to also move the .torrent file that it creates (from a magnet link into the session directory) into this done directory with the same name as the torrent and a .torrent extension. I tried adding another cp command, but I can not seem to figure out which variable ($d.get_hash did not work) stores the torrent's hash (which is what the .torrent files are named in the session directory). Is there a way to do this with rTorrent, if so how?

  Read the article

• Run Microsoft SCCM Remote Control Viewer on Client Machines?

  - by David Mackey

  I've install SCCM 2012 on a server and have successfully used the Remote Control option to take control of a system I've setup to be managed by SCCM. Now, I don't want to have to log in to a server every time I want to access this client...is there a way to run the Remote Control Viewer client on my desktop OS so I can take remote control of systems rather than having to remote in from the server? This seems like very basic functionality...but I haven't been able to figure it out thus far.

  Read the article

• Cannot access host from a virtualbox guest using bridged adapter

  - by David Dai

  I have a windows 7 host with firewall turned off. And I have a windowsXP guest running on Virtualbox 4.2.4r81684. In my windowsXP guest I tried to connect to the FTP server on my host machine(which used to work well) but it didn't work. I tried to ping my host machine, but it didn't work either. Then I tried to ping my guest from host, it worked well. my guest ip is :192.168.1.95 my host ip is : 192.168.1.9 route table on guest machine is this: C:\Documents and Settings\wenlong>route PRINT =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...08 00 27 66 54 6c ...... AMD PCNET Family PCI Ethernet Adapter #2 - Packe t Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.95 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.95 192.168.1.95 20 192.168.1.95 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.1.255 255.255.255.255 192.168.1.95 192.168.1.95 20 224.0.0.0 240.0.0.0 192.168.1.95 192.168.1.95 20 255.255.255.255 255.255.255.255 192.168.1.95 192.168.1.95 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None arp cache is this: C:\Documents and Settings\wenlong>arp -a Interface: 192.168.1.95 --- 0x2 Internet Address Physical Address Type 192.168.1.1 00-26-f2-60-3c-04 dynamic 192.168.1.9 90-e6-ba-c2-90-2f dynamic It's strange because there was no problem days before and I didn't make any changes to the setting. could anybody help? PS. the guest can communicate with other machines in the LAN(for example 192.168.1.114) ok. it just cannot connect to the host machine.

  Read the article

• IIS seems to send email twice

  - by David Brunelle

  Hi, we have a request page in our website that send email to confirm the request. It seem that whenever this page is accessed, some (not all of them) are sent more than once at different time, sometime hours apart. The code (which is an old ASP page) looks fine as it sends only once to the recipient. So I doubt it's a programming related problem. When looking at the Exchange server, the tech told me that he seems to be receiving the request twice at different time, so the problem comes from what's between the code and Exchange. My hypothesis is that IIS seem to 'remember' the page and rerun it for some reason. Any hint on where to start? We have IIS 6 (in french if it makes any difference) with Exchange 2007. IIS is running on a Windows Server 2003 machine (virtual machine I believe) in a DMZ. I don't know about Exchange. Thank you.

  Read the article

• How can I get WAMP and a domain name to work on a non-standard port?

  - by David Murdoch

  I have read countless articles on setting up a domain on WAMP to listen on a port other than 80; none of them are working. I've got Windows Server 2008 (Standard) with IIS 7 installed and running on port 80 (and 443). I've got WAMP installed with the following configuration. Listen 81 ServerName sub.example.com:81 DocumentRoot "C:/Path/To/www" <Directory "C:/Path/To/www"> Options All MultiViews AllowOverride All # onlineoffline tag - don't remove Order Allow,Deny Allow from all </Directory> localhost:81 works with the above configuration but sub.example.com:81 does not. Just to make sure my firewall wasn't getting in the way I have disabled it completely. My sub.example.com domain is already pointing to my server and works on IIS on port 80. Also, if I disable IIS and change the Apache port from 81 to 80 it works. Yes, I am restarting Apache after each httpd.conf change. :-) I don't need any other domain (or sub domains [I don't even care about localhost]) configured which is why I'm not using a VirtualHost. Any ideas what is going on here? What could I be doing wrong? Update Changing Listen to 80 but keeping ServerName as sub.example.com:81 causes navigation to sub.example.com:80 to work; this just doesn't seem right to me. Could ServerName be ignoring the :port part somehow? netstat -a -n | find "TCP": >netstat -a -n | find "TCP" TCP 0.0.0.0:81 0.0.0.0:0 LISTENING TCP 0.0.0.0:135 0.0.0.0:0 LISTENING TCP 0.0.0.0:445 0.0.0.0:0 LISTENING TCP 0.0.0.0:912 0.0.0.0:0 LISTENING ... TCP 127.0.0.1:81 127.0.0.1:49709 TIME_WAIT ...

  Read the article

• Program to print gCal or iCal calendars in a monthly one calendar per column format

  - by David Smith

  I'm moving my family off of using the low tech "Boynton Mom's Family Calendar" to schedule things but I'd like to be able to create a monthly printout of the calendar in the same "Boynton" format (I'm sure it has an official name). The format is kind-of like a spreadsheet where each row of the calendar is a different day of the month and there is a separate column for each person in the family. I have all our calendars on Google but they are also accessible from iCal on the Mac. Is there a Mac program that can get the data from gCal or iCal print out the calendars in the Boynton format?

  Read the article

• Confused about the Windows 7 Preinstallation Kit

  - by David Brown

  I build custom PCs and would like to use the Windows 7 Preinstallation Kit to make installation go a little quicker and customize the Windows image. However, since each PC is built to a particular customer's specifications, the hardware will rarely be the same. So, I would like to have a single answer file that will work for everything. I'm not sure if that's possible, however. What I mostly want to do for now is add my support information as well as pre-set anything that I would normally change after each installation completes. I have a Windows 7 Professional Upgrade DVD set (both 32-bit and 64-bit), but no OEM disks. I copied the Install.wim file to my local drive and opened it in the Windows System Image Manager, but it asks me to choose a catalog file specifically for each edition of Windows 7. Will this limit the answer file to whichever edition I choose? I would think choosing Starter would give me the most basic settings, which would apply to all other editions, but I'm not entirely sure of this. I don't intend to install any extra applications or drivers. I merely want to insert an OEM disk, my OPK USB drive, and have it work for whatever edition of Windows 7 I'm installing. If a large number of similarly-configured PCs need to be built, I'll go ahead and create a custom answer file in that case, but for a single machine order, that seems like overkill. In addition, do I need a separate answer file for 32-bit and 64-bit versions of Windows 7? Or will it work for both, even though I copied the Install.wim file from the 32-bit disk? Thanks!

  Read the article

• Esx servers in a DMZ

  - by James

  I have two ESX 3.5 servers in a DMZ. I can access these servers on any port from my lan via a VPN. Servers in the DMZ are unable to initiate connections back to the lan, for obvious reasons. I have a vCenter server on my lan and can initially connect to the esx servers fine. However the esx servers then try to send a hearth beat back to the vCenter server on udp/902 obviously this will not get back to the vCenter server, which then marks the ESX servers as not responding and disconnects. There are two broad solutions I can think of; 1) Try to tell vCenter to ignore not getting heart beats. The best I can do here is delay the disconnect by 3 mins. 2) Try some clever network solution. However again I am at loss. Note: The vCenter server is on a lan, and cannot be given a public IP, so firewall rules back will not work. And also I cannot setup a VPN from the DMZ to the lan. **I am adding the following, explanation that I added to the comments Ok maybe this is the bit that I not explaining well. The DMZ is on a remote site, an entirely independent network (network 1). The vCenter server is on our office lan (network 2). Network 2 can connect to any machine on any port on network 1. But network 1 is not allowed to initiate a connection to network 2. Any traffic destined to network 2 from network 1 gets dropped by the firewall as it is traffic to a non-routable address. The only solution I can think of is setting up a VPN from network 1 to network 2, but this is not acceptable So any clever folk out there any ideas? J

  Read the article

• Powerbook G4 unresponsive on wake?

  - by David

  I have a Powerbook G4 17" and I recently updated to the Mac OS 10.5.8 and got a monitor. I put it to sleep by closing the lid and sometimes it resumes normally and sometimes it doesn't. It doesn't matter if it's on sleep for a day or 10 minutes, it just happens randomly. It wakes up, but the screen doesn't flash blue for a few seconds like it normally would, indicating that it found the second monitor. It just wakes up, and a picture appears on both screens and the mouse moves, but nothing responds. The only way I can make it work again is by holding down the power button until it shuts down and then turning it on again. this frustrating because then I have to reopen all my programs and Safari tabs. I tried resetting the PMU by unplugging everything and taking out the batter, then holding the power button for five seconds, but it has the same problem no matter what I do.

  Read the article

• 2 pdfs look same on XP, different on Win7

  - by David Dai

  I have 2 pdf files. I compared them with WinMerge, BeyondCompare, and even compared their checksums. They are exactly the same to me in every way. If I open them with Adobe Reader in Xp, and compare them with my bare eyes, they look the same. But!!! If I open them with Adobe Reader in Win7, and compare them with my bare eyes, they look very different!(particularly border width). I'm sorry I cannot share the 2 pdf files but I will appreciate it if anyone could come up with any idea!

  Read the article

• Linux (Ubuntu 12.04) two gateways one nic

  - by David

  I have Ubuntu 12.04 Server edition Two gateways, both on 192.168.0. network, let's make them 192.168.0.1 and 192.168.0.2 I've read you should be able to add second gateway into /etc/network/interfaces, that it will build out all the routing automatically, but I get "duplicate option" error. So if I have one default gateway, let's say 0.1, and a connection comes through from the 0.2 gateway, my understanding is that it still tries to respond through 0.1 gateway. Can we change this behavior?

  Read the article

• amavisd + postfix + dovecot blocks gif images

  - by David W

  I occasionally have a client who tries to email me and says his email gets blocked by my server. When I check the logs, I see this: Sep 6 18:12:52 myers amavis[15197]: (15197-08) p.path BANNED:1 [email protected]: "P=p003,L=1,M=multipart/mixed | P=p002,L=1/2,M=application/ms-tnef,T=tnef,N=winmail.dat | P=p004,L=1/2/1,T=image,T=gif,N=image001.gif,N=image001.gif", matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" And then a little later... Sep 6 18:12:58 myers amavis[15197]: (15197-08) Blocked BANNED (.image,.gif,image001.gif,image001.gif), [213.199.154.205] [157.56.236.229] <[email protected]> - > <[email protected]>, quarantine: banned-g4QhZGvwJvDF, Message-ID <6A9596BE385EC1499F83E464FA9ECCA20C668320@BY2PRD0611MB417.namprd06.prod.outlook.com>, mail_id: g4QhZGvwJvDF, Hits: -, size: 20916, 8439 ms From this and the bounce that he forwards me (to a different address I give him), I determine that its bouncing because of the file in his signature (image001.gif). However, that does NOT match the "key" in this part of the log: matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" Furthermore, the .gif extension is nowhere to be found in the /etc/amavisd.conf file (i.e. I'm not blocking emails because they contain .gif images). Am I missing something here? This is strange... and annoying.

  Read the article

• Paste a list of dates in format of "mm/dd/yy" to iWork-Numbers

  - by David.Chu.ca

  I have trouble to paste a list of strings in the format of 'mm/dd/yy' into iWork-Numbers. For example, I have a list of strings(text in VIM): 04/01/10 04/03/10 04/13/10 I copy those strings and then paste into my iWork-Numbers worksheet. The result will be: 2004-01-10 2004-03-10 04/13/10 It looks like that Numbers (mac workseet application in iWork) tries to convert the first two digits into year, then the next two into month if less than 12 and last two digits to a day, for the first two rows. For the third(04/13/10), since the middle two digits are 13 and cannot be a month, then this row is pasted as it is (actually it is what I need). Is there any way to paste whatever as they are, without any "smart date conversion"? Do I have to change settings in Numberers or Mac OS's System preference?

  Read the article

• Group Policy installation failed error 1274

  - by David Thomas Garcia

  I'm trying to deploy an MSI via the Group Policy in Active Directory. But these are the errors I'm getting in the System event log after logging in: The assignment of application XStandard from policy install failed. The error was : %%1274 The removal of the assignment of application XStandard from policy install failed. The error was : %%2 Failed to apply changes to software installation settings. The installation of software deployed through Group Policy for this user has been delayed until the next logon because the changes must be applied before the user logon. The error was : %%1274 The Group Policy Client Side Extension Software Installation was unable to apply one or more settings because the changes must be processed before system startup or user logon. The system will wait for Group Policy processing to finish completely before the next startup or logon for this user, and this may result in slow startup and boot performance. When I reboot and log in again I simply get the same messages about needing to perform the update before the next logon. I'm on a Windows Vista 32-bit laptop. I'm rather new to deploying via group policy so what other information would be helpful in determining the issue? I tried a different MSI with the same results. I'm able to install the MSI using the command line and msiexec when logged into the computer, so I know the MSI is working ok at least.

  Read the article

• Merge LVM Partition with unallocated Space

  - by David

  I have a linux hard drive with three areas: /dev/hda1 - ext3 boot partition (20 MB) /dev/hda2 - lvm2 main partition (6 GB) unpartitioned space - 12 GB I would like to merge the unpartitioned space into the lvm2 partition known as /dev/hda2. I tried using GParted, but it does not support lvm2. What commands or utilities could I use to add the unpartitioned space to hda2 without losing my existing data?

  Read the article

• Powershell import-module webadministration

  - by David

  Every time I execute this command invoke-command -computername REMOTEPC -scriptblock { import-module WebAdministration; new-item "$env:systemdrive\inetpub\testsite" -type directory; New-WebSite -Name TestSite -Port 81 -PhysicalPath "$env:systemdrive\inetpub\testsite" } I get the following error Invalid class string (Exception from HRESULT: 0x800401F3 (CO_E_CLASSSTRING)) + CategoryInfo : NotSpecified: (:) [Get-ChildItem], COMException + FullyQualifiedErrorId : System.Runtime.InteropServices.COMException,Microsoft.PowerShell.Commands.GetChildItemCommand The website is created successfully as far as I can see. The following command gives the same error when enumerating the testsite Invoke-Command -computername REMOTEPC { import-module webadministration; dir -path IIS:\Sites\ } Name ID State Physical Path Bindings PSComputerName Default Web Site 1 Started http *:80: REMOTEPC Invalid class string (Exception from HRESULT: 0x800401F3 (CO_E_CLASSSTRING)) + CategoryInfo : NotSpecified: (:) [Get-ChildItem], COMException + FullyQualifiedErrorId : System.Runtime.InteropServices.COMException,Microsoft.PowerShell.Commands.GetChildItemCo mmand Any suggestions would be appreciated

  Read the article

• How can I delete virtual networks from command line?

  - by David Cobb

  I have Hyper-V Server 2008 R2 (without GUI) running at my colo for a week. I was connected via RDP and could use the menu interface and command line. I figured out how to connect Hyper-V Manager from my Win7 laptop (THANK YOU HVREMOTE!), and created and installed my VM. I created a virtual network that didn't work (no connectivity from my VM) so I created another using different settings, and now have lost access to the Hyper-V host. No ping, no RDP. Since I don't have console access, I cannot troubleshoot. I believe if I deleted the Virtual Networks I'd regain access, but I need a command line instruction for this, that the staff onsite could enter to accomplish this. I find no help anywhere obvious (MSDN, etc), the keywords are too general. Can anyone refer me to simple steps how to do this over command line or with the menu based interface on the console?

  Read the article

• OS X random, jumpy dragging behavior

  - by Chris

  This problem has been going on since I got 10.7, and is persisting or even getting worse since I updated to Mavricks. The best way to describe it is thru an example- Let's say I'm working in Safari. Everything is working fine. Then, I'll switch to another app by clicking on it's window, for example, I'll click on Messages to shoot back a reply. When I click back to Safari, keyboard and mouse inputs don't work! The only way I can regain control of the app (Safari) is by clicking on the apps top bar, which then causes the app to jump left or right. If I'm in Messages and I switch back to Safari by clicking said top bar, it works fine. Same with switching back and forth using command-tab. I've narrowed the problem down to this - the first app (Safari, in this example) is, for some reason, deciding that I'm in the process of dragging the window around. This could be just an oddly persistent glitch in my system, but has anyone else seen this before? Perhaps a misplaced default write... somewhere along the line? Update A PRAM reset did absolutely nothing

  Read the article

• Databases supporting parallel processing across multiple servers

  - by David

  I need a database engine that can utilize multiple servers for processing a single SQL query in parallel. So far I know that this is possible with the some engines, though none of them are feasible for me either because of pricing or missing features. The engines currently known to me are: MS SQL (enterprise) DB2 (enterprise) Oracle (enterprise) GridSQL Greenplum

  Read the article

• Emails going to Junk for Hotmail recipients

  - by David George

  We send daily mass emails to our customers (~30,000+ emails per day). We have problems with Hotmail users receiving our emails. Sometimes the email goes to the Junk folder, but often it will got to their inbox, but the content is blocked so the user sees a message saying "This email was blocked and may be dangerous". If an email is sent to GMAIL it is usually not blocked, but it does show up as from "Uknown" instead of the company. Please be advised I've done the following: 1. No RBLs Checked on - http://multirbl.valli.org/ 2. We do have SPF records published 3. We do have reverse DNS setup 4. Our company even signed up for the Junk Mail Reports Program at Hotmail Here is a sample header, I've noticed the X-SID-Result and the X-AUTH-Result both FAIL every time at Hotmail: X-Message-Delivery: Vj0xLjE7dXM9MDtsPTA7YT0wO0Q9MTtTQ0w9MQ== X-Message-Status: n:0 X-SID-Result: Fail X-AUTH-Result: FAIL X-Message-Info: JGTYoYF78jFqAaC29fBlDlD/ZI36+S6WoFmkQN10UxWFe1xLHhP+rDthGRZM87uHYM926hUBS+s0q46Yx9y6jdurhN6fx0bK Received: from privatecompany.com ([WanIPAddress]) by col0-mc3-f30.Col0.hotmail.com with Microsoft SMTPSVC(6.0.3790.4675); Wed, 5 May 2010 08:41:27 -0700 X-AuditID: ac10fe93-000013bc00000534-46-4be191a1618e Received: from INTERNAL-Email-SERVER([InternalIPAddress]) by privatecompany.com with Microsoft SMTPSVC(6.0.3790.4675); Wed, 5 May 2010 11:41:21 -0400 From: Private Company, Inc.<[email protected]> To: [email protected] Message-Id: <[email protected]> Subject: Date: Wed, 5 May 2010 11:42:46 -0400 MIME-Version: 1.0 Reply-To: [email protected] Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: 8bit X-Brightmail-Tracker: AAAAAA== Return-Path: [email protected] X-OriginalArrivalTime: 05 May 2010 15:41:27.0837 (UTC) FILETIME=[6D06E4D0:01CAEC69]

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >