Search Results

Search found 7204 results on 289 pages for 'almost dead'.

Page 115/289 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Dell Latitude E4300 TouchPad - Odd Behavior

  - by Cade Roux

  I'm seeing some intermittent behavior on the touchpad. First it wasn't working at all. Then during restart, for a little while it seemed like the buttons attached to the joystick and external mouse were both swapped left/right. Then I went in to the dell touchpad control and disabled the touchpad and re-enabled it and nothing happened. Then a short while after disabling the joystick the touch pad started working. So I restarted to see if it would keep the settings and before login, the touchpad appeared to work, then after login it stopped working for a few minutes while login continued. Then after the login was almost completed it started to work again. It appeared to have retained the settings for the disabled joystick. It seems like perhaps there are conflicting mouse drivers trying to simultaneously or similar. This doesn't seem normal for the touchpad to be disabled for so long after login. What steps should I take to ensure the drivers are right?

  Read the article

• Missing disk space in Windows XP

  - by Jørn Schou-Rode

  On my mother's Lenovo laptop, Windows XP claims that the hard drive is almost full. According to the properties window, 52.7 out of 55.2 GB is in use: By deleting temp files from Internet Explorer, System Restore, Recycle bin, Windows Update, System Cleanup, I managed to free up about one GB. That's still 50 GB in use, which still is a lot more than I expected. Hence, I gave good old WinDirStat a spin, and here's the output: It might be hard to read here, but the first line says that the total amount of disk space in use on drive C is 24.3 GB. So Windows claims usage of 52.7 GB and WinDirStat can only account for 24.3 GB. Where is the other half of that disk space being used? I hope someone has an answer, or some tricks or tips to do further research. UPDATE: The laptop in question has an SSD hard drive. I am aware that these disk (at least the earlier ones) have a limited life-time. Could the symptoms described be caused by wear and tear on the SSD?

  Read the article

• Firefox 3.6 performance increase tricks.......

  - by metal gear solid

  I use many Add-ons which helps me in Web development so i can't uninstall those addons. and usually I keep open lots of tabs in Firefox. And almost always keep Firefox on on my system. I use default profile only I always keep every addons and firefox itself updated. I found some addons to reduce memory use on Firefox addons site , but user reviews were not good for them still Is there any tested tricks to increase performance and reduce memory use of Firefox 3.6, which really works?

  Read the article

• How to set the IP address in a customized OpenWRT compilation

  - by Berdus

  I have been struggling today customizing OpenWRT. I checkout the stable using SVN, "make menuconfig" to customize the image, "make" it and run it on a router. Almost all my modifications work, except for the (Seemingly trivial) task of changing the default 192.168.1.1 address. I tried numerous files (scripts as well as config files) but I can't seem to change it (I can change it for a brief moment after boot using the "preinit" file, but after a few seconds it reverts to default). I suspect I should be setting it in the /etc/network file, but modifications there seem to be overwritten during boot. Maybe it has something to do with the br-lan interface? Does anybody have some thoughts on the subject? Thanks!

  Read the article

• Looking for something like Google's Picasa [closed]

  - by Skizz

  I almost like Picasa, but there are two issues that irk me and I wondered if anyone knew of an application that does what Picasa does but without the following problems: Network drives. Picasa is hopeless with network drives. Ideally, I'd like photos to be stored remotely and thumbnail databases to be stored locally with a client-server set-up to update client databases. The main aim is to get updates propagated to clients efficently, reduce network bandwidth and have quick browsing on the client. It needs to be snappy when used over a wireless network. This is just a minor point but the folder view looks awful, especially when it uses those tiny thumbnails. (Also, what is it with folders being drawn vertically. Having spent years looking at folders orientated horizontally, turning them on their side looks so wrong.)

  Read the article

• SEAGATE Barracuda 7200.11 HDD not running

  - by Dane411

  After a huge research, I'm stuck at the beggining of getting my HDD data back. Whats happening to me is that in the moment when I plug the power wire to my external 1TB SEAGATE Barracuda 7200.11 ST31000333AS HDD Fw LC15, it makes the sound like it's spinning to almost full speed and then shuts down and spins up again, and so on. It's well known that those HDDs have a bad firmware that someday randomly fails. There are like 2 main problems identified, BSY (busy) state, and LBA0 error. Last time I connected it to power nothing happened, it didnt try to start at all, is it that so called bricked state? I guess my HDDs error is the first one, but I dont really know if what I described is that BSY state or not, neither I know how to check it. How could I know it? Thank you so much!

  Read the article

• How do you manage updates without a staging environment: CentOS 6.3

  - by Gregg Leventhal

  I am managing about 20 servers, many of them virtual. They are almost all different purpose, and none are clustered. I have a distributed LAMP stack, a few application servers, some build servers, a few KVM hosts. They are CentOS 6.3 mostly with a few Ubuntu (unfortunately). I don't have the resources to setup a staging environment where I can have duplicates of my machines and test updates before rolling them out. I am taking file backups. What I want to know is how you are approaching backing up your Linux systems. I assume you don't just do yum update, but then how are you choosing the packages worthy of updating? When (if ever) are you updating the kernel, etc.. How do you test updates without a staging environment? Snapshot and hope for the best?

  Read the article

• Which free IMAP-supporting webmail would you recommend?

  - by Razor

  Considering a machine with IIS 7.5/PHP 5.2/asp.net and mysql/MSSQL available, which webmail would you pick? Don't think it's relevant but the mail server is installed on localhost, and is hmailserver. If it's one using asp.net it'd be a bonus, but PHP is ok as well and probably offers more choices. "Client side" look and feel definitely needed, flash/silverlight/ajax not a problem. I have also seen this question, but being asked almost 2years ago and being focused on php webmails, I thought that some better option could've been released in the meantime.

  Read the article

• Can't access files on external drive after reformatting Macbook Pro

  - by Peter Wells

  I recently had to reformat my Macbook Pro, and imported my account and settings from Time Machine via the Migration Assistant. Everything on the Mac itself is fine, but now I don't have permission to access almost everything on my external drive. A number of folders have the little red 'no access' sign on them and I can't rename or move anything. Looking at the info for these files, it appears that access rights were attached only to my old user account. Is there some way to reassign these files and folders to my new user account? Thanks.

  Read the article

• What happens to a Windows Dynamic Drive

  - by GruffTech

  In my windows (Windows 7) I have two primary logical volumns, One is on a SSD harddrive for my operating system and installed software, and my other is a Dynamic volume for my stored media. (I do alot of work with HD footage) I have all my media on the original DV tapes for backup purposes, just having them all available on my harddrive at all times is a major convience for me, well worth the few hundred dollar investment those 2TB drives were. Anyway, Long story short is my windows install has become problematic and I want to reformat windows. Does this, or will this effect my dynamic drive in any way? I've got almost 3 TB of video on there and i really dont want to re-import all my DV tapes.

  Read the article

• Apache htaccess with mod_expires Not Working for certain directories

  - by keyboarddrummer

  I have a Joomla site that I am trying to enable caching using mod_expires. I have the .htaccess in the root of the site and have added the options as found on the page http://www.pactsoftware.nl/tools/joomla-optimization.html Using the PageSpeed extension in Chrome, prior to adding this in my .htaccess, my site scores a 55 (Caching is at the top, and lists a lot of images, CSS, and JS files). After these directives, it scores 70, with caching in the yellow, but still lists some image files (some are two directories deep and the rest are four). I checked for any other .htaccess files in the Joomla root, but none are between those folders and the root. It is almost as if htaccess only works in that one directory, not the subfolders. I have tried putting a .htaccess in each affected subdirectory, but it does not work. Does anyone have any ideas?

  Read the article

• How I can fix the "Display Driver has stopped responding and has recovered"?

  - by Vitor Rangel

  I'm using a GeForce GTX 580, with Windows 7 64-bit. The driver version of the GTX is 301.42. The problem happens after a few minutes, when I'm playing specifc games. It won't happen in all games - And I don't have any idea why these games doesn't work. The games that doesn't work: Battlefield 3, Civilization V, Sniper Elite V2. The games that work: Mass Effect 3, Crysis 2, Team Fortress 2, Left 4 Dead 2, Skyrim, L.A. Noire. As you can see, it's not a problem of "The games that demand more stop working". I've tryed updating the driver of the graphics-card, the bios of the motherboard, even formated my computer (It was needing it) and instaled every driver in the last version possible. This problem happens since I bought my graphics-card, 6 months ago. After a few minutes, from 10 to 20, the pixels in the monitor become strange, with random colors and effects, like it was broken. Then, everything goes black, and the message appears "Display Driver has stopped responding and has recovered". After that, I need to close the game and start again. I am not overclocking, and my temperature never goes higher than 70ºC.

  Read the article

• How to set TV-out options under Linux of an Geforce 9600 GT video card

  - by polemon

  I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

  Read the article

• Video converters don't work anymore after reinstalling Windows

  - by tassiekev

  A few days ago, I decided to reinstall Windows 7 as my HD partition seemed to be nearly full and things were slowing down. I'd been using Handbrake almost exclusively to convert TV recordings and used Freemake on occasion. Following the reinstall, I can't get either to work: Handbrake says it's encoding for about 2 seconds and then says it's finished, but there are no converted files of any size. Freemake just says 'Conversion Error' and won't go any further. As an experiment I tried two programs that I don't normally use, VideoReDo & Any Video Converter. Both worked fine. Anyone got any clues?

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

• Exchange 2010 Hub Transport Role Fails - Registry Keys Missing?

  - by DKNUCKLES

  I've inherited an attempted Exchange 2010 implementation from a colleague that apparently failed. I've almost managed to bring it back from the dead, but the Hub Transport role fails to install with the following error [10/06/2012 02:30:44.0119] [2] Beginning processing Set-LocalPermissions -Feature:'Bridgehead' [10/06/2012 02:30:44.0166] [2] [ERROR] Unexpected Error [10/06/2012 02:30:44.0166] [2] [ERROR] The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0182] [2] Ending processing Set-LocalPermissions [10/06/2012 02:30:44.0182] [1] The following 1 error(s) occurred during task execution: [10/06/2012 02:30:44.0182] [1] 0. ErrorRecord: The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0182] [1] 0. ErrorRecord: System.ArgumentException: The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.GetTargetRegistryKey(XmlNode targetNode) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.ChangePermissions[TTarget,TSecurity,TAccessRule,TRights](XmlNode targetNode, Dictionary`2 rightsDictionary, GetTarget`1 getTarget, GetOrginalPermissionsOnTarget`2 getOrginalPermissionsOnTarget, SetPermissionsOnTarget`2 setPermissionsOnTarget, CreateAccessRule`2 createAccessRule, AddAccessRule`2 addAccessRule, RemoveAccessRuleAll`1 removeAccessRuleAll) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetPermissionsOnCurrentLevel[TTarget,TSecurity,TAccessRule,TRights](XmlNode permissionSetNode, String targetType, Dictionary`2 rightsDictionary, GetTarget`1 getTarget, GetOrginalPermissionsOnTarget`2 getOrginalPermissionsOnTarget, SetPermissionsOnTarget`2 setPermissionsOnTarget, CreateAccessRule`2 createAccessRule, AddAccessRule`2 addAccessRule, RemoveAccessRuleAll`1 removeAccessRuleAll) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetPermissionsOnCurrentLevel(XmlNode permissionSetNode) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetFeaturePermissions(String feature) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.InternalProcessRecord() [10/06/2012 02:30:44.0197] [1] [ERROR] The following error was generated when "$error.Clear(); Set-LocalPermissions -Feature:"Bridgehead" " was run: "The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE".". [10/06/2012 02:30:44.0197] [1] [ERROR] The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0197] [1] [ERROR-REFERENCE] Id=BridgeheadLocalPermissionsComponent___2e2dbc2a97cb4429bc2074edc50bedbd Component=EXCHANGE14:\Current\Release\Shared\Datacenter\Setup [10/06/2012 02:30:44.0197] [1] Setup is stopping now because of one or more critical errors. [10/06/2012 02:30:44.0197] [1] Finished executing component tasks. [10/06/2012 02:30:44.0244] [1] Ending processing Install-BridgeheadRole I've been unable to find any documentation on how to resolve this issue. Any help would be appreciated.

  Read the article

• Tweaks to make Cleartype better at high resolutions?

  - by ULTRA_POROV

  Cleartype is great when displaying small text (say 10-16px). However when you display something above 20px it starts looking like mud. Just compare it to Photoshop. Photoshop rendering at small size is not very impressive, too blurry. But if you compare it at 20px, Photoshop wins all the time. Cleartype looks jaggy around the edges, almost like there is no Cleartype at all. Can this be fixed, or is it just the way Cleartype is?

  Read the article

• How do I make a Windows virtual machine replicate to another datacenter/cloud?

  - by zippy

  We have a Windows 2008 VM running IIS and SQL Server Express (it's an all-in-one web application). We need to have another copy at our secondary datacenter site. What is the best way to do this? It doesn't have to be running all the time but it has to have almost the latest copy of the current VM. I took a look at VMWare Fault Tolerance and after the heart attack at the price I starting looking for another solution. If need be I wouldn't mind copying it over to a cloud VM provider, if I can find one that lets me copy my own VMs up and start them up without any conversion process.

  Read the article

• Download databasename.bak file

  - by Jordon

  I have downloaded databasename.bak file from my hosting company, when i tried to restore that DB file in SQL server 2008 it is keep on giving me following error. The media family on device 'C:\go4sharepoint_1384_8481.bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE HEADERONLY is terminating abnormally. (Microsoft SQL Server, Error: 3241) According to this error and from following link http://www.sqlcoffee.com/Troubleshooting047.htm It is clear that either file i am downloading is corrupt or it is getting corrupted on the way? Any idea, why I am keep on receiving this error? I tried almost all ways but unable to fix this problem, please help me.

  Read the article

• How to set default permissions for automounted FAT drives in Ubuntu

  - by piman

  I've got many FAT32 drives that I'd like to mount in Ubuntu such that they have permission mode 700 for directories and 600 for all other files. By default, they have 755 for all files, which is not particularly useful since almost no non-directories should be executable, and it screws up version control repos hosted on the drives. "Back in the day" I would have had the drives listed in /etc/fstab with the umask/dmask I want and there was no such thing as a default. These days, drives automount under their volume names. Which is great, except now I have no idea how to set the default. I have tried changing the /system/storage/default_options/vfat/mount_options gconf key with no apparently effect. It was 077 initially but the mounted drive reflected a default of 022; changing it and re-inserting the drives resulted in the files still having permission bits of 755.

  Read the article

• Delay before booting with laptop

  - by Priednis

  I have almost the same problem as in Delay before booting? My computer is a practically new (couple months) Lenovo X200 Tablet (System Model 7449FXG). So when I press the power button, the indicator light that means "computer is on" turns on, but nothing else happens for about 5 mins, after that the computer starts booting normally. The same happens also on restart. And no USB or any other device for that matter is plugged in to the computer. And at the delay time the monitor is blank - actually not on at all.

  Read the article

• Links break in IE9 when using Wordpress plugins in non Wordpress Page

  - by mouli

  I have a site that uses SEF URLs and htaccess RewriteRules to serve up the pages. This has worked fine for several years until the arrival of IE9. Now it appears that the links are not being rewritten and the site is dead in the water. I have tried different compatabilty modes, to no avail, and I've played with the Rewrite Rules over and over, tried different doctypes and a few other browser settings. I agree that it cannot in theory be a browser specific problem if the problem is with the htaccess file but this site works in IE8, firefox and chrome. I have run the rewriterule through a validator and it looks fine. Any ideas would be appreciated as I am running out of ideas. The site is www.marlboroughsounds.co.nz a sample link is http://www.marlboroughsounds.co.nz/walking/freedom-walk-queen-charlotte-track/4dfw and the rewrite rule thats not working looks like this: RewriteRule ^walking/.*/([a-z0-9_]*)/?$ /walking.php?act_code=$1 [L] The link fails and it serves up a browser 404 page, not even the custom 404 I have for the site. Any ideas would be much appreciated as I am stumped.

  Read the article

• Is the Zune HD's audio card better or worse than the iPod touch's?

  - by MatthewThepc

  Firstly, if this is the wrong site to ask this question I apologize, but I didn't see one for "music players" on the stack exchange website :) After reading a few people online say that music playing from a Zune HD sounds better to them than that on an iPod touch, I was wondering whether there's any truth to that? From what I can tell, the Zune HD uses a Wolfson Microelectronics WM8352, while the first-generation iPod Touch (which the Zune HD was competing with) used a Wolfson Microelectronics WM8758BG, and newer models use the Cirrus Logic CS4398 and CS42L61. Which ones are better (to make the question less subjective, let's say in terms of quality, range, & accuracy of output)? Admittedly, I have almost no idea how everything compares and works together, but it would seem to me that, just by looking at the version numbers, the iPod has been better since it's launch. Is there anything else that effects sound quality? Thanks!

  Read the article

• Windows 7: How to prevent Windows from caching my desktop wallpaper

  - by rmartz

  I have a service running that renders a changing wallpaper every 5 minutes or so, and replaces the current image file with the new one automatically (That is to say, new image but same filename). On Linux, the change is detected almost automatically, and so I have the most current wallpaper. However, on my Windows 7 machine (Which syncs the image with my Linux machine over Dropbox), it appears to cache the wallpaper from the last time I manually set the wallpaper. The image never changes, even if I restart. Is there a way to make Windows detect the file change, or periodically refresh the wallpaper cache? I'd like to avoid third-party apps if at all possible.

  Read the article

• rsync doesn't use delta transfer on first run

  - by ockzon

  I'm trying to synchronize a large local directory (with a batch file using rsync 3.0.7 on Cygwin, Windows 7 x64, 30k files, 200gb size) to a remote server (Debian x64 with kernel 2.6, rsyncd 3.0.7) over a slow internet connection (90kbyte/s upload). I know almost all files are identical and I verified that using md5sum locally and remotely. However when executing rsync from my local machine every file gets transferred completely for the first time. When I terminate the batch file after a few transfers and run it again then the already transferred files are skipped. But as soon as it gets to a file not yet transferred it uploads the file as a whole again instead of noticing that the checksum is the same locally and remotely. The batch file calling rsync looks like this (backslashes and line brakes added here for readability): c:\cygwin\bin\rsync.exe --verbose --human-readable --progress --stats \ --recursive --ignore-times --password-file pwd.txt \ /cygdrive/d/ftp/data/ \ rsync://[email protected]:33400/data/ | \ c:\cygwin\bin\tee.exe --append rsync.log I experimented using the following parameters in varying combinations but that didn't help either: --checksum --partial --partial-dir=/tmp/.rsync-partial --compress

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >