Search Results

Search found 61623 results on 2465 pages for 'data storage'.

Page 118/2465 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

  • Dell VRTX - slow cluster shared storage

    - by NorbyTheGeek
    I have a brand new Dell VRTX box set up as a Failover Cluster running HA Hyper-V virtual machines. This is my first time setting up clustering, and my first time with one of these boxes, so I'm sure I've missed something. The virtual machines are experiencing high disk latency and bad performance when accessing their VHD(x) files located on a Cluster Shared Volume. The VRTX has 10 x 900 GB 10K SAS drives in RAID 6 configuration, and the VRTX has the redundant Shared PERC 8 controllers. Both blades have full access to the virtual disks. There are two M520 blades installed, each with 128 GB RAM. MPIO is configured for the PERC 8 controllers. Operating system on the blades is Server 2012 (NOT R2). The RAID 6 array is split into a small (8 GB) volume for cluster quorum witness and a large (6.5 TB) volume for a Cluster Shared Volume (mounted on the nodes as C:\ClusterStorage\Volume1) An example of slow disk access: logging into a Server 2012 VM and having Server Manager come up automatically. Disk access goes to 100%, with write speeds at 20 MB or so, read speeds of 500 KB or so, and Average Response Time of over 1000 ms, sometimes spiking at 4000-5000 ms or so. It's the latency that really worries me. Is there something specific I should look at in my configuration? It doesn't seem to matter whether I use VHD or VHDX, dynamic or static.

    Read the article

  • Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

    - by Casey
    I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

    Read the article

  • Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

    - by braveterry
    I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

    Read the article

  • Files missing after copying from one sdcard to another using Ubuntu 12.04

    - by Abhi Kandoi
    I have two Kingston sdcards 8GB and 32GB. The 8GB for HTC Sensation and 32GB for my Tablet (Chinese). I soon ran out of space on my phone and decided to swap the data between the sdcards. I copied the data of 32GB sdcard to my PC(with Ubuntu 12.04) deleted everything on the 32GB sdcard and copied data from the 8GB sdcard to the other sdcard. At last I copied the data from my PC to the 8GB sdcard(before this I deleted everything that was on it before). Now the problem is that the 8GB sdcard has the data exactly the same, but the 32GB sdcard has some missing data. All my photos(not copied or posted on Facebook) and Songs are lost. Please help as to what I can do to get my data back? I have Android Revolution HD (ICS 4.0.3) on my rooted HTC Sensation (India). I suspect it has something to do with my data loss.

    Read the article

  • Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

    - by Casey
    I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

    Read the article

  • iSCSI connection timing out on ESX 3.5 against a NetApp storage appliance

    - by Jesse1973
    I get a timeout on iSCSI on different ESX hosts (3.5) at different times. It is puzzling, as both the ESX hosts as windows and other guests are experiencing timeouts. The iSCSI network is segregated on a private network. Here is an export of vmkiscsid.log from last night: 2010-02-10-12:30:38: iscsid: an InitiatorAlias= is required, but was not found in /etc/vmware/vmkiscsid/initiatorname.iscsi 2010-02-10-12:30:38: iscsid: LogLevel = 0 2010-02-10-12:30:38: iscsid: LogSync = 0 2010-02-10-12:30:42: iscsid: Login Success: iqn.1992-08.com.netapp:sn.101197719,default,192.168.73.2,3260,2001, 0x1 2010-02-10-12:30:42: iscsid: connection1:0 is operational now 2010-02-16-02:03:35: iscsid: Kernel reported iSCSI connection 1:0 error (1008) state (3) 2010-02-16-02:03:39: iscsid: connection1:0 is operational after recovery (2 attempts) 2010-02-16-04:02:27: iscsid: Kernel reported iSCSI connection 1:0 error (1008) state (3) 2010-02-16-04:02:32: iscsid: connection1:0 is operational after recovery (2 attempts) Should i edit the timeout value on the ESX host for iSCSI? This may work around the problem but will not solve it.

    Read the article

  • Custom SNMP Cacti Data Source fails to update

    - by Andrew Wilkinson
    I'm trying to create a custom SNMP datasource for Cacti but despite everything I can check being correct, it is not creating the rrd file, or updating it even when I create it. Other, standard SNMP sources are working correctly so it's not SNMP or permissions that are the problem. I've created a new Data Query, which when I click on "Verbose Query" on the device screen returns the following: + Running data query [10]. + Found type = '3' [SNMP Query]. + Found data query XML file at '/volume1/web/cacti/resource/snmp_queries/syno_volume_stats.xml' + XML file parsed ok. + missing in XML file, 'Index Count Changed' emulated by counting oid_index entries + Executing SNMP walk for list of indexes @ '.1.3.6.1.2.1.25.2.3.1.3' Index Count: 8 + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.1' value: 'Physical memory' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.3' value: 'Virtual memory' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.6' value: 'Memory buffers' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.7' value: 'Cached memory' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.10' value: 'Swap space' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.31' value: '/' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.32' value: '/volume1' + Index found at OID: '.1.3.6.1.2.1.25.2.3.1.3.33' value: '/opt' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.1' results: '1' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.3' results: '3' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.6' results: '6' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.7' results: '7' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.10' results: '10' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.31' results: '31' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.32' results: '32' + index_parse at OID: '.1.3.6.1.2.1.25.2.3.1.3.33' results: '33' + Located input field 'index' [walk] + Executing SNMP walk for data @ '.1.3.6.1.2.1.25.2.3.1.3' + Found item [index='Physical memory'] index: 1 [from value] + Found item [index='Virtual memory'] index: 3 [from value] + Found item [index='Memory buffers'] index: 6 [from value] + Found item [index='Cached memory'] index: 7 [from value] + Found item [index='Swap space'] index: 10 [from value] + Found item [index='/'] index: 31 [from value] + Found item [index='/volume1'] index: 32 [from value] + Found item [index='/opt'] index: 33 [from value] + Located input field 'volsizeunit' [walk] + Executing SNMP walk for data @ '.1.3.6.1.2.1.25.2.3.1.4' + Found item [volsizeunit='1024 Bytes'] index: 1 [from value] + Found item [volsizeunit='1024 Bytes'] index: 3 [from value] + Found item [volsizeunit='1024 Bytes'] index: 6 [from value] + Found item [volsizeunit='1024 Bytes'] index: 7 [from value] + Found item [volsizeunit='1024 Bytes'] index: 10 [from value] + Found item [volsizeunit='4096 Bytes'] index: 31 [from value] + Found item [volsizeunit='4096 Bytes'] index: 32 [from value] + Found item [volsizeunit='4096 Bytes'] index: 33 [from value] + Located input field 'volsize' [walk] + Executing SNMP walk for data @ '.1.3.6.1.2.1.25.2.3.1.5' + Found item [volsize='1034712'] index: 1 [from value] + Found item [volsize='3131792'] index: 3 [from value] + Found item [volsize='1034712'] index: 6 [from value] + Found item [volsize='775904'] index: 7 [from value] + Found item [volsize='2097080'] index: 10 [from value] + Found item [volsize='612766'] index: 31 [from value] + Found item [volsize='1439812394'] index: 32 [from value] + Found item [volsize='1439812394'] index: 33 [from value] + Located input field 'volused' [walk] + Executing SNMP walk for data @ '.1.3.6.1.2.1.25.2.3.1.6' + Found item [volused='1022520'] index: 1 [from value] + Found item [volused='1024096'] index: 3 [from value] + Found item [volused='32408'] index: 6 [from value] + Found item [volused='775904'] index: 7 [from value] + Found item [volused='1576'] index: 10 [from value] + Found item [volused='148070'] index: 31 [from value] + Found item [volused='682377865'] index: 32 [from value] + Found item [volused='682377865'] index: 33 [from value] AS you can see it appears to be returning the correct data. I've also set up data templates and graph templates to display the data. The create graphs for a device screen shows the correct data, and when selecting one row can clicking create a new data source and graph are created. Unfortunately the data source is never updated. Increasing the poller log level shows that it appears to not even be querying the data source, despite it being used? What should my next steps to debug this issue be?

    Read the article

  • update all the servers through one virtual servers using Storage are network virtual machine

    - by Mr.Calm
    Using UBUNTU and Virtal Box by Oracle, and Using this script to start nginx in Virtual Box, and placing it in Virtual box inside~/init.d #!/bin/bash ### BEGIN INIT INFO # Provides: Testinit # Required-Start: # Required-Stop: # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Start daemon at boot time # Description: Enable service provided by daemon. ### END INIT INFO # RETVAL=0; start() { CurrentTime=$(date +%d/%m/%Y"-"%I:%M:%S) ./usr/local/nginx/sbin/nginx echo "Current Time:"$CurrentTime>>/home/server/Desktop/NginxLogs.txt echo "!Starting nginx!" >>/home/server/Desktop/NginxLogs.txt Like this i want to write auto script (setup.sh file) and place that script in all virtual boxes inside my system, for example 8 virtual boxes and in all Virtual boxes NGINX is installed. Now, The thing is i am facing problem when i want change something in setup.sh i have to go to each and every virtual box, or Communicate each Virtual machine through SSH from my main machine. i am thinking to write another script (ex: Update.sh),and inside that script we give one path of file which is saved and recently edited in main machine (ex: DummySetup.sh). as soon as i run that script all the setup.sh files which are saved in each virtual machines should update the change or replace contents with DummySetup.sh's contents. Hope this is possible thing. Help would be appreciated.Thanking you

    Read the article

  • Remote Desktop failed logon event 4625 not logging correctly on 2008 Terminal Services server

    - by Zone12
    When I use the new remote desktop with ssl and try to log on with bad credentials it logs a 4625 event as expected. The problem is, it doesn't log the ip address, so I can't block malicious logons in our firewall. The event looks like this: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-Security-Auditing" Guid="{00000000-0000-0000-0000-000000000000}" /> <EventID>4625</EventID> <Version>0</Version> <Level>0</Level> <Task>12544</Task> <Opcode>0</Opcode> <Keywords>0x8010000000000000</Keywords> <TimeCreated SystemTime="2012-04-13T06:52:36.499113600Z" /> <EventRecordID>467553</EventRecordID> <Correlation /> <Execution ProcessID="544" ThreadID="596" /> <Channel>Security</Channel> <Computer>ontheinternet</Computer> <Security /> </System> <EventData> <Data Name="SubjectUserSid">S-1-0-0</Data> <Data Name="SubjectUserName">-</Data> <Data Name="SubjectDomainName">-</Data> <Data Name="SubjectLogonId">0x0</Data> <Data Name="TargetUserSid">S-1-0-0</Data> <Data Name="TargetUserName">notauser</Data> <Data Name="TargetDomainName">MYSERVER-PC</Data> <Data Name="Status">0xc000006d</Data> <Data Name="FailureReason">%%2313</Data> <Data Name="SubStatus">0xc0000064</Data> <Data Name="LogonType">3</Data> <Data Name="LogonProcessName">NtLmSsp</Data> <Data Name="AuthenticationPackageName">NTLM</Data> <Data Name="WorkstationName">MYSERVER-PC</Data> <Data Name="TransmittedServices">-</Data> <Data Name="LmPackageName">-</Data> <Data Name="KeyLength">0</Data> <Data Name="ProcessId">0x0</Data> <Data Name="ProcessName">-</Data> <Data Name="IpAddress">-</Data> <Data Name="IpPort">-</Data> </EventData> </Event> It seems because the logon type is 3 and not 10 like the old rdp sessions, the ip address and other information is not stored. The machine I am trying to connect from is on the internet and not on the same network as the server. Does anyone know where this information is stored (and what other events are generated with a failed logon)? Any help will be much appreciated.

    Read the article

  • Reverse proxy setup for distributed storage

    - by vise
    I have 4 file servers that I want to access under a single mount point from another server. This server has a web application that should serve content from the mounted point. I think I can achieve this with glusterfs. Considering that the file servers have fairly powerful hardware, I want to install a webserver on each of them and serve those files via a reverse proxy. Any thoughts on how I may be able to do so?

    Read the article

  • Can't install SB750 RAID drivers in Windows 7 for two additional storage drives

    - by jf46
    Mobo: ASUS M4A79XTD, 790X/SB750 OS: Windows 7 x64 I currently have SATA 1-4 set to RAID and SATA 5-6 set to IDE. I have an SSD connected to SATA5 with Windows 7 installed on it, and that works fine. I also have configured a RAID 1 array of two 1TB HDDs, connected to SATA 1 and 2. These don't show up in Windows, and I'm having trouble getting the RAID driver installed. I even tried booting from the Windows DVD and repairing or installing Windows, but when I navigated to the relevant .sys files on my motherboard's driver CD, Windows setup told me that the files in question weren't relevant to my hardware. To be clear: I'm not trying to install Windows on a RAID. I have Windows installed on a separate disk on a separate SATA controller. I just want to get the SB750 RAID drivers installed so that the Windows disk utility can see my RAID 1 array, which is composed of two other disks. Do I need to wipe my SSD and reinstall Windows to get the RAID driver installed? That seems kind of ridiculous, and given what I described above, I'm not even sure it would work. Any help or guidance would be appreciated - thanks! Edit: Also, I've copied the driver files from the mobo CD into system32 and rebooted, no luck. Then I changed HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStorV\Start from 3 to 0, and that didn't work either.

    Read the article

  • Windows 7 explorer always crashes, opens small "Personalized Settings" window

    - by Ian Sellar
    My Windows 7 desktop PC, built by me, started acting very weird in the last couple of days. I use it quite often, about half of the time through TeamViewer. Explorer would crash and restart randomly, almost always through TeamViewer. This made me suspect that TeamViewer was the problem but I have reproduced it with and without TeamViewer several times. The only way I can seem to get the problem not to occur is by booting into Safe Mode. I have used CCleaner and Malwarebytes to make sure it wasn't a registry error or malware causing the problem, and I have tried the fix in the seemly related issue here as well every other fix I have found online including removing security updates KB980408 and KB2926765 as well as using "sfc /scannow" and a bunch of other things I can't remember. More recently when I try to start explorer it is popping up a small window that says "Personalized Settings" on the top, but is completely empty and crashes instantly. The only way I can get it to disappear is to kill the explorer.exe process. I wish I could take a screenshot but I can't seem to open paint or even find the exe. I have tried restarting it, I have tried starting it while the personalized settings window was open. I have come up with two lists of processes the first is the list of active processes when I boot into safe mode and explorer seems to work fine. The second is the list of processes that I can narrow it down to in normal boot and still replicate the problem. There is one process that I can't seem to close. NisSrv.exe which is describes as "Microsoft Network Realtime Inspection Service". When I try to close the process NisSrv.exe it says "The operation could not be completed. Access is denied." When I try to close the related service it gives the same message. Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 2,660 K smss.exe 304 Services 0 1,196 K csrss.exe 408 Services 0 4,156 K wininit.exe 444 Services 0 4,608 K csrss.exe 452 Console 1 8,700 K services.exe 492 Services 0 7,700 K winlogon.exe 524 Console 1 5,756 K lsass.exe 536 Services 0 10,644 K lsm.exe 544 Services 0 4,316 K svchost.exe 652 Services 0 8,976 K MsMpEng.exe 804 Services 0 40,696 K explorer.exe 1332 Console 1 85,220 K ctfmon.exe 1376 Console 1 3,680 K dllhost.exe 1624 Console 1 8,656 K chrome.exe 1408 Console 1 98,504 K WmiPrvSE.exe 2352 Services 0 6,472 K chrome.exe 1744 Console 1 65,116 K taskmgr.exe 372 Console 1 14,948 K cmd.exe 2776 Console 1 2,960 K conhost.exe 1816 Console 1 3,580 K tasklist.exe 2308 Console 1 5,868 K And the list of processes I have narrowed it down to. Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 2,808 K smss.exe 316 Services 0 1,216 K csrss.exe 484 Services 0 4,532 K wininit.exe 596 Services 0 4,604 K csrss.exe 604 Console 1 23,676 K services.exe 652 Services 0 11,344 K lsass.exe 668 Services 0 12,692 K lsm.exe 676 Services 0 4,464 K MsMpEng.exe 972 Services 0 68,436 K winlogon.exe 168 Console 1 7,784 K svchost.exe 496 Services 0 19,140 K NisSrv.exe 3176 Services 0 808 K svchost.exe 1684 Services 0 11,260 K taskmgr.exe 4524 Console 1 20,696 K cmd.exe 4764 Console 1 7,224 K conhost.exe 4772 Console 1 6,916 K sublime_text.exe 2340 Console 1 45,012 K dllhost.exe 4476 Console 1 8,736 K tasklist.exe 3796 Console 1 5,768 K WmiPrvSE.exe 1768 Services 0 6,344 K Here is the event data xml from event viewer for the error I am getting. <EventData> <Data>explorer.exe</Data> <Data>6.1.7601.17567</Data> <Data>4d672ee4</Data> <Data>vrfcore.dll</Data> <Data>6.3.9600.16384</Data> <Data>5215f8f5</Data> <Data>80000003</Data> <Data>0000000000003a00</Data> <Data>12e4</Data> <Data>01cfb84fa70f89dc</Data> <Data>C:\Windows\system32\explorer.exe</Data> <Data>C:\Windows\SYSTEM32\vrfcore.dll</Data> <Data>e5957093-2442-11e4-9f8a-94de806ed9cb</Data> </EventData> I was looking through the eventvwr log again and I found this, possibly related <EventData> <Data>runonce.exe</Data> <Data>6.1.7601.17514</Data> <Data>4ce7a253</Data> <Data>MSVCR100.dll</Data> <Data>10.0.40219.325</Data> <Data>4df2bcac</Data> <Data>c0000005</Data> <Data>000000000003c145</Data> <Data>670</Data> <Data>01cfb8dabbd85942</Data> <Data>C:\Windows\system32\runonce.exe</Data> <Data>C:\Windows\system32\MSVCR100.dll</Data> <Data>fa6f82b9-24cd-11e4-80a8-94de806ed9cb</Data> </EventData> And the general error details Faulting application name: Explorer.EXE, version: 6.1.7601.17567, time stamp: 0x4d672ee4 Faulting module name: vrfcore.dll, version: 6.3.9600.16384, time stamp: 0x5215f8f5 Exception code: 0x80000003 Fault offset: 0x0000000000003a00 Faulting process id: 0xc38 Faulting application start time: 0x01cfb84e5e852c5f Faulting application path: C:\Windows\Explorer.EXE Faulting module path: C:\Windows\SYSTEM32\vrfcore.dll Report Id: 9dc19e6d-2441-11e4-9f8a-94de806ed9cb Another probably unrelated error that I seem to be getting pretty often. Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. My explorer tab in Autoruns seen below along with the error when I try to uncheck something. I should add that I seem to be able to disable shell extensions with ShellExView but I still can't get explorer to start correctly. EXPLORER SHELL UPDATE - See screenshot below I can access the explorer right click menu through a file manager I downloaded called NexusFile, but still no luck starting explorer. Another round of errors that I am getting regarding Windows Search Service The search service has detected corrupted data files in the index {id=4700}. The service will attempt to automatically correct this problem by rebuilding the index. Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) followed by The Windows Search Service is being stopped because there is a problem with the indexer: The catalog is corrupt. Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801 and The plug-in in <Search.JetPropStore> cannot be initialized. Context: Windows Application, SystemIndex Catalog Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) and The gatherer object cannot be initialized. Context: Windows Application, SystemIndex Catalog Details: The content index catalog is corrupt. (HRESULT : 0xc0041801) (0xc0041801) and The Windows Search Service cannot load the property store information. Context: Windows Application, SystemIndex Catalog Details: The content index database is corrupt. (HRESULT : 0xc0041800) (0xc0041800) WER Log http://pastebin.com/WXKGDT4Q I'll add information as I remember it or people request it.

    Read the article

  • Resize partition of Windows 7 running on VirtualBox with dynamically allocated storage

    - by Nicolas Raoul
    I run Windows 7 inside VirtualBox. I resized the disk of Windows 7 from 25 GB to 50 GB: VBoxManage modifyhd Windows\ 7\ Pro.vdi --resize 50000 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% PROBLEM: I can' grow the partition, neither with Windows 7 itself nor with GParted: It looks like VirtualBox does not tell the client OS about the new size. What additional step is necessary?

    Read the article

  • Storage (EBS) attached to my EC2 instance reporting files on two devices at once

    - by Philip Isaacs
    I have on EC2 instance with two attached EBS drives. One drive /dev/sda1 is mounted on / The second /dev/sda2 is mounted on /var2 So here's what's strange. Whenever I add any files to /var2 the it is also reporting that the / device is also filling up. As if they are the same device. It's so strange. So if I were to save a 10 mb file to a directory on /var2. Both / and /var2 use 10 mb of space up. Is this bizarre?

    Read the article

  • What is your favorite password storage tool?

    - by Marcel Levy
    Aside from personal passwords, I'm always juggling a number of project-specific passwords, including those for network, web and database authentication. Some authentication can be managed with ssh keys and the like, but everywhere I've worked I also faced the need for the management of passwords that need to be available to a number of different people. So what do you use, either for personal or team-based password management? Personally I'd like to hear about cross-platform tools, but I'm sure other people would be satisfied with Windows-only solutions. I know the stackoverflow podcast tackled this issue in #7 and #9, but I'm hoping we can come up with the definitive answer here. Update: Even though this question was asked before its sibling site existed, you should probably add your two cents to the more active question over at superuser, which is a more appropriate venue for this.

    Read the article

  • Best way to attach 96 tb to workstation

    - by user994179
    I'm running a workstation with dual xeon 5690's (12 physical/24 logical cores), 192 gb of ram (ie, maxed-out), Windows 7 64bit, 5 slots for adapter cards, and 1 tb of internal storage, with 5 more internal bays available. I have an app that creates data files totaling about 88 tbs. These are written once every 14 months, and the rest of the time the app only needs to read them; and 95% of the reads are sequential reads of huge chunks of data. I have some control over how big the individual files are, but ideally they would be between 5 and 8 tbs. The app will be reading from only one drive at a time, and the nature of the data is such that if (when) a drive dies I can restore the data to a new disk from tape. While it would be nice to be able to use the fastest drive/controllers available, at this point size matters more than speed. After doing lots of reading, I am leaning toward buying a bunch of cheap 2tb drives and putting them into a bunch of cheap enclosures. All this stuff is going into my home office, so I need to avoid the raised floor/refrigerated approach. My questions: Is the cheap drive/enclosure solution the best one for this situation? Given the nature of the app and the way the data is used, does RAID make sense? If so, which one? For huge sequential reads, would Usb 3.0 and eSata be a wash performance-wise? For each slot available on the workstation, can I hook up an enclosure that can hold multiple drives? Or is it one controller per drive? If I can have multiple drives on one controller, am I essentially splitting the bandwidth (throughput)? For example, if I have a 12 bay enclosure, is the throughput of the controller reduced by a factor of 12? Are there any Windows 7 volume/drive/capacity limits I should be aware of? Thanks

    Read the article

  • Not enough storage is available to process this command

    - by Mohit
    I am getting this error on almost all of the operations on a Windows 7 pro 32 bit machine. By operations I mean anything I do. Update a repo from subversion. Access a local IIS Site. Copy a big folder. Run an installer.and sometime if I try again. It get solved. I think there is something wrong wit windows7 . I searched around and found posts suggesting to increase IRPStackSize value in registry I did that no Luck. I am using Microsoft Security Essentials Version: 1.0.1961.0 as my antivirus package Once this errors starts popping up. I have to restart and then in after some random time. It starts showing up again. Any help is appreciated. I am losing lot of my time in restarting my system or retrying again and again.

    Read the article

  • Thoughts on home NAS server

    - by user826955
    I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

    Read the article

  • CDN Rerouting on 404 (file not yet in synch with original storage)

    - by Alan Ristic
    Here is the problem. I've setup my app(on EC2) to store uploaded images directly on Amazon S3. I'd like to be able to serve static files(cdn) from my 'home' server so I wrote script that does sync from S3. But there is a window of (at least) one minute in synch. Now I see two solutions on the problem of pics not been available on 'home' server here: 1.I write script on EC2 (where the app resides) to fetch from DB pics that have status of "not-yet-synch", which is default state when user uploads picture. The script then does a ping to picture and if it gets OK response, updates DB from "not-yet-synch" to "synch". 2.Prefered solution would be to let apache (in this case) redirect request for an image if it sees 404 (e.g. doesent find image requested) to S3. This way I wouldn't need script from solution 1. So what approach do you suggest I take in solving this redundancy problem? Or what is practice in production environments? To further clarify; I'd like so serve images first from 'home' server, if that fails serve them from S3. Tnx, Alan

    Read the article

  • Plug and Go NAS Storage

    - by graham.reeds
    My wife and I are separating. One of the things we need to extricate is the media we have accumulated over the years. So I am looking for a NAS solution that is a) relatively low-cost, b) reliable and c) easy for a non-geek to use (I don't want to be tech support). All it needs to do is hold our iTunes library, photos, course work and maybe some movies and TV shows that I currently have. She will be connecting via her Netbook. I have seen this thread but the reviews on Amazon aren't particularly favourable. Due to the need for simplicity, WHS and FreeNAS are none-starters. I need redundancy as if a single drive system was to die then she would lose her course work and photos. Is the ReadyNAS the only real solution out there?

    Read the article

  • Excel: What formula combines this data into one COUNT amount?

    - by Mike
    I have 30 colleagues who are answering questions over 3 time periods. Each has their own Excel workbook with the questions, and over the year they update it. I collate their worksheets into one master worksheet, but now need to combine their answers into a simple table. The questions, the time periods and then a COUNT of how many answered it. For example: I need a table that shows me how many people (not the persons name at this point) answered question 10 in time period 2. I can't use a database before someone mentions it ;). Many thanks Mike.

    Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >