Search Results

Search found 3850 results on 154 pages for 'tech ref'.

Page 118/154 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Solaris 10: cannot ping to/from server

  - by anurag kohli

  All, I have a Solaris 10 server which is not reachable by IP (ie can't ping to/from the server). I believe I have the default route setup correctly. See below: # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.62.100 netmask ffffff00 broadcast 192.168.62.255 ether 0:14:4f:b1:9b:30 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.62.0 192.168.62.100 U 1 40 bge0 224.0.0.0 192.168.62.100 U 1 0 bge0 default 192.168.62.1 UG 1 0 127.0.0.1 127.0.0.1 UH 1 4 lo0 # # cat /etc/defaultrouter 192.168.62.1 I have verified layer1 and layer 2 are up on the switchport, and that it's on the correct VLAN. I have also checked the default gateawy (192.168.62.1) is in fact reachable since I can ping it from my PC: Pinging 192.168.62.1 with 32 bytes of data: Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=3ms TTL=254 Reply from 192.168.62.1: bytes=32 time=6ms TTL=254 I'm at a loss as to what is wrong. I would highly appreciated your assistance. Thank you very much.

  Read the article

• Trouble cloning a Macbook Pro hard drive

  - by Mirko Froehlich

  I am trying to upgrade the 250GB hard drive in my MacBook Pro (early 2008 model) to a 750GB drive. I have connected the new drive via an external USB enclosure. The drive is recognized fine, I can format it, etc. However, every time I try to clone the drive, I am getting Input/Output errors. Before the clone operation, I have verified both the internal and the external drive using Disk Utility, and they both check out fine. After the clone operation, the external drive shows multiple "Invalid node structure" errors: I have tried two approaches for cloning the drive: Using Disk Utility, by starting from the OSX install DVD Using Carbon Copy Cloner The outcome is the same in both cases. The Carbon Copy Cloner logs show a handful of the following types of errors: rsync: mkstemp "<... an external filename ...>" failed: Input/output error (5) rsync: stat "<... an external filename ...>" failed: Input/output error (5) The actual files affected seem to be different across different runs of the application. Before the last run, I used Disk Utility to (once more) reformat the external drive and explicitly overwrite it with zeros, but this made no difference. I also tried running a surface scan in Tech Tool Pro overnight. It got about 2/3 of the way through before I had to disconnect the drive (had to take my MacBook Pro to work), but so far it didn't report any bad blocks. Assuming it scans the drive in the same order in which blocks would be allocated during actual use, it seems like if bad blocks were to blame for the clone failures, they should have been found already (given that the source drive is only 250GB). As a last attempt, I may try SuperDuper as well, although my understanding is that it uses the same underlying rsync approach as Carbon Copy Cloner, so it's unlikely to perform any better. Are there any other things I should try before I send the drive in for a replacement? Could these problems be caused by my internal drive, even though it works fine and checks out fine in Disk Utility?

  Read the article

• Investigating a potential CPU failure

  - by Jernej

  On a Ubuntu server that I am using for computations I have recently observed that some CPU extensive programs (GUROBI,CPLEX) often segfault. Being in correspondence with tech support of the respective programs I was suggested that it may be a hardware issue. The administrator of the server performed a detailed memtest and it turned out that the RAM modules appear to be fine. Hence I've used the tool mprime to test the CPU and the following two lines appear multiple times durring the execution of the stress tests: [Worker #4 Oct 18 18:47] FATAL ERROR: Rounding was 0.498046875, expected less than 0.4 [Worker #4 Oct 18 18:47] Hardware failure detected, consult stress.txt file. The stress.txt file in itself is not very verbose about what could be the cause of this error so I would like to ask whether anyone here happens to know what could be the cause of this issue? Is there some other test I could perform to nail the problem even further? The temperature of the system (and all cores) was fine during the entire stress test (+69.0°C (high = +80.0°C, crit = +98.0°C)) the CPU in question is a Intel Core i7-2600K CPU @ 3.40GHz and is not overclocked or modified in any way. Also what is interesting that if I run mprime to only stress the CPU all tests pass fine. The error is only triggered when I let mprime stress the CPU+RAM.

  Read the article

• Moving Zend Framework 2 from apache to nginx

  - by Aleksander

  I would like to move site that uses Zend Framework 2 from Apache to Nginx. The problem is that site have 6 modules, and apache handles it by aliases defined in httpd-vhosts.conf, #httpd-vhosts.conf <VirtualHost _default_:443> ServerName localhost:443 Alias /develop/cpanel "C:/webapps/develop/mil_catele_cp/public" Alias /develop/docs/tech "C:/webapps/develop/mil_catele_tech_docs/public" Alias /develop/docs "C:/webapps/develop/mil_catele_docs/public" Alias /develop/auth "C:/webapps/develop/mil_catele_auth/public" Alias /develop "C:/webapps/develop/mil_web_dicom_viewer/public" DocumentRoot "C:/webapps/mil_catele_homepage" </VirtualHost> in httpd.conf DocumentRoot is set to C:/webapps. Sites are avialeble at for example localhost/develop/cpanel. Framework handles further routing. In Nginx I was able to make only one site available by specifing root C:/webapps/develop/mil_catele_tech_docs/public; in server block. It works only because docs module don't depend on auth like others, and site was at localhost/. In next attempt: root C:/webapps; location /develop/auth { root C:/webapps/develop/mil_catele_auth/public; try_files $uri $uri/ /develop/mil_catele_auth/public/index.php$is_args$args; } Now as I enter localhost/develop/cpanel it gets to correct index.php but can't find any resources (css,js files). I have no Idea why reference paths in browswer's GET requsts changed to https://localhost/css/bootstrap.css form https://localhost/develop/auth/css/bootstrap.css as it was on apache. This root directive seems not working. Nginx handles php by using fastCGI location ~ \.(php|phtml)?$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param APPLICATION_ENV production; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } I googled whole day, and found nothing usefull. Can someone help me make this configuration work like on Apache?

  Read the article

• Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

  - by Patrick

  While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

  Read the article

• Websockets Server with Fault-Tolerance and Durable Message Store

  - by smitchell360

  I am starting to experiment with websockets. Does anyone know of a websockets server (open source or paid) that provides a durable store of the websocket "channel"? All of the examples that I have found do not address durability -- if a websockets server goes down, all "channel" data is lost. Services such as Pusher do not really discuss whether they address the durability issue (and I have not received a response from tech support yet). Happy to roll my own, but would rather not reinvent the wheel. EDIT: I'm not looking for websockets 101 information. That is readily available and understood. I'm looking for a server (open source or paid) that supports websockets and has a durable store for the websocket data so that, in the event that a server fails, a new server can take over where the original one left off. Two main purposes: 1. support failover scenarios contemplated by the websockets Network Working Group http://tools.ietf.org/html/draft-ibc-websocket-dns-srv-02#section-5.1 (most importantly so that missed messages are sent when a client connects to a failover server) 2. support scenarios where new subscribers must receive all past messages that were published. Of course this can be handled at the application layer...but that is not what I am looking for. EDIT So, after some research the following installed options seem to be the most robust: Kaazing Migratory Migratory (http://migratory.ro) Hosted services that seem "real" Pusher (great API but no history feature yet) PubNub (has history) All of the above services have graceful fallback to other communication methods if websockets are not available. I was not able to find any open source that provided "out of the box" clustering, fail-over, and a durable message store to play back history. There are some projects that may serve as good starting points, but not exactly what I am looking for.

  Read the article

• ISA 2000 and COD MW2 Steam

  - by twlichty

  OK, so maybe not the "proper use" of network resources, but we enjoy the odd COD game during lunch hours. When we played COD4, we had a dedicated server setup at the back of the server room. With MW2, we need to be able to connect to steam to be able to play multi-player. I've found this support article here: https://support.steampowered.com/kb%5Farticle.php?ref=8571-GLVN-8711 Which outlines all the ports I need to open. I went through and created the following rules in ISA 2000 (I'm stuck with 2000 for now). Protocol Definition: Steam Primary connection: Port 27000, UDP, Send Receive Secondary Connection: Port range 27001-27030 Send Receive Protocol Definition: Steam TCP In Primary connection: 27014, TCP, Inbound Secondary Connection: Port range: 27015-27050, Inbound Protocol Definition: Steam 4380 Primary connection: 4380, UDP, Send Receive When I start steam on my local workstation (I did add an exception to the Vista Firewall to allow steam), the steam client sits on "Updating Steam" for 5 minutes then errors out with: You must connect to the internet first. Any ideas? I assume I missed something. Thanks for your help.

  Read the article

• Dell Dimension 8400 Startup error

  - by Michael

  Hello all, thanks first for taking the time to read this and possibly help me...... now I am pretty decent of a computer tech...but not enough. I am having an issue with my computer which is running windows xp and as I mentioned it is a dell Dimension 8400. as soon as I power the system up the fan goes into hyper drive (spins like crazy and is very loud) then the start up screen with dell comes up and the loading bar gets stuck on the process of "Bios Revision A00" and never loads beyound that. I have read alot about it and think that the main problem was that it can not locate the file (which does have an updated version) I think it is A09. I can not enter safe mode, Bios mode or anything. I do have the file on my other computer and I was wondering if there is a way that I can use a usb flash drive (as I have read on other sites) to create a bootable MS-Dos diskette but I am failing at creating as such....is this possible? or is there anything else I can do? I tried to remove the battery from the system for about 10 minutes while it was completely unplug and tried then to reboot it and go into the bios menu but the same thing keeps happening....can anyone help me :-(

  Read the article

• Tripwire help Required

  - by ramaperumal

  I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

  Read the article

• Does a mini PCIe SSD fit into a Acer Aspire One?

  - by Narcolapser

  Question: What, if any, mini PCIe SSDs fit into the mini PCIe slot of the Acer Aspire one AOD250? Info: I have an Aspire One and I've been considering loading it with an SSD. The mini PCIe drives fascinate me and so I want to try that approach. Also they tend to be cheaper and not much slower. (at least not on Read time which matters more for a netbook) But I've heard that some times computers don't support certain mini PCIe cards. And I was wondering if anyone knew about the Aspire One? I tried asking Acer tech support, but they didn't know jack and spent the whole time informing that I would have to support my Ubuntu install on my own, which I was. Anyway. Rant Aside, I'm looking at this drive: http://www.newegg.com/Product/Product.aspx?Item=N82E16820183252 It states it is exclusively for the Eee PC. now does that mean It was designed for the Eee PC but will work in my netbook. or is something going to go wrong? (like right now my concern is it physically not fitting.) Any information would be appreciated. o7

  Read the article

• Debian/Ubuntu - No network connection

  - by leviathanus

  I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

  Read the article

• Recommendation on remote access setup for accessing customer systems

  - by gregmac

  I'm looking for a product recommendation (open or commercial) that will allow remote access to customer sites for tech support purposes. We need to be able to gain access to help troubleshoot problems on servers. Currently end up using anything from RDP on public IP, to various VPNs that clients happen to have, to webex-type sessions that require lots of interaction from both sides to get things working. This often means a problem that could take 10 minutes to solve takes an extra 30+ minutes messing around trying to get a connection up. There are multiple customer sites, which should NOT have access to each other. At each site, there is anywhere from 1 to 8 servers (Windows 2003 or 2008) that need to be accessed. Support connection to machines even if they're behind a firewall/router with no public IP Be able to selectively allow/deny access from customer site. Customer site should not be able to connect outbound to anywhere else (our systems, or other customer sites) Support multiple users from our end If not a VPN connection (where RDP could be used over top), should support: Remote desktop access, including copy/paste File transfers Preferably would have some way to list all remote systems, showing online/offline. Anyone have any suggestions?

  Read the article

• DXVA and ATI.... what am I missing?

  - by Shiki

  ATI Radeon HD3650 ffdshow (the one comes with CCCP 2010-10 AND the latest from Free-codecs site) Catalyst 10.12 Latest DirectX, Windows 7 HP x64 If I try to play it simply, the player (mpc-hc) won't use the acceleration. If I disable checks, I get artifacts. Back then it worked perfectly with my Intel and ATI too (Lenovo ThinkPad T500, switchable graphics). This only appeared recently. What should I do? What am I missing? If possible, I don't really want to downgrade drivers (waaa ATI drivers s.ck ... sorry but.. honestly), because the older one got a buggy DP driver so my external display gets a totally wrong resolution. Info about the media file: Video: Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Codec ID : V_MPEG4/ISO/AVC Writing library : x264 core 88 r1462 7fcffde Encoding settings : cabac=1 / ref=8 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=8 / psy=1 / psy_rd=0.80:0.20 / mixed_ref=1 / me_range=24 / chroma_me=1 / trellis=2 / 8x8dct=1 / cqm=0 / deadzone=21,11 / fast_pskip=1 / chroma_qp_offset=-3 / threads=3 / sliced_threads=0 / nr=0 / decimate=1 / mbaff=0 / constrained_intra=0 / bframes=8 / b_pyramid=2 / b_adapt=2 / b_bias=0 / direct=3 / wpredb=1 / wpredp=2 / keyint=250 / keyint_min=25 / scenecut=40 / intra_refresh=0 / rc_lookahead=40 / rc=crf / mbtree=1 / crf=16.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / ip_ratio=1.40 / aq=1:1.00 The sample file I'm testing at the moment: [Coalgirls]_Kiddy_Girl-and_01_(1920x1080_Blu-Ray_FLAC)_[91428679].mkv (I tried many x264 files, no use.) Artifacts

  Read the article

• Dell XPS 15 L502X hard drive Partition

  - by Mohan Gajula

  I have a situation here. I got my new Dell XPS 15 Laptop. The configuration of hard drive is as below : Volume 1: (OEM Partition): 133MB Volume 2: OS (C:): 685.25 GB Volume 3: Recovery : 13.25 GB Now, I am trying to re-partition my C Drive to have a C: drive with 100 GB and a new drive with 585 GB. Earlier, I tried using the Windows 7 Disk Management to shrink and extend the volume. That lead to the OS and hard drive not working. Dell Tech support tried to fix the issue, but they were not able to fix the issue online. Later a Dell Technician arrived my place, and replaced the hard drive with a new hard drive. Please help me re-partition the C: Drive with 100 GB, and new D drive with 585 GB. I don't want to lose my Recovery Partition. SOLUTION As Suggested by KCotreau below , I have done exactly. I have resized the C drive to 100 GB. And then applied the changes. Windows got restarted. On the boot screen, the partition was taking place. It took around 30 mins ( approx. ). Once after restart, I can see my C drive is 100 GB. Now opened the Easeus again. And created a new partition for the free space ( 585 GB ) this took 10 seconds to create. Here goes the screenshot after partitioning. Thanks to KCotreau. You are amazing.

  Read the article

• Creating Routes using the second NIC in the box

  - by Aditya Sehgal

  OS: Linux I need some advice on how to set up the routing table. I have a box with two physical NIC cards eth0 & eth1 with two associated IPs IP1 & IP2 (both of the same subnet). I need to setup a route which will force all messages from IP1 towards IP3 (of the same subnet) to go via IP2. I have a raw socket capture program listening on IP2 (This is not for malicious use). I have set up the routing table as Destination Gateway Genmask Flags Metric Ref Use Iface IP3 IP2 255.255.255.255 UGH 0 0 0 eth1 If I try to specify eth0 while adding the above rule, I get an error "SIOCADDRT: Network is unreachable". I understand from the manpage of route that if the GW specified is a local interface, then that would be use as the outgoing interface. After setting up this rule, if i do a traceroute (-i eth0), the packet goes first to the default gateway and then to IP3. How do I force the packet originating from eth0 towards IP3 to first come to IP2. I cannot make changes to the routing table of the gateway. Please suggest.

  Read the article

• Massive Memory Leaks?

  - by Mads

  Hi, I seem to have huge memory leaks, which are confusing me. I'm running fusion 3.1 / Windows 7 on Snow Leopard. It's a clean install with all upgrades applied. I've given fusion 8GB on a 14GB machine. I've installed VS2008 & Eclipse in Windows 7. Nothing unusual. Inside Task Manager in Windows 7, my memory footprint stays reasonable, at <2GB. But in OSX, Activity Monitor shows the footprint of vmware-vmx to be much larger. It starts at 2 GB, which seems fine, but whenever I'm actually doing anything in Windows, vmware-vmx's footprint grows at a few MB per second. After 20 mins or so it's using ~10GB and everything grinds to a halt. Throughout this, Task Manager still says I'm only using 2GB. And whatever I do in windows seems to increase vmware-vmx's memory footprint. Even closing down an application seems to make it go up. So is this par for the course in fusion? I was previously using parallels 3 / Vista under Leopard, and it worked fine. I'd assumed my new fusion config would work better, but this makes it completely unusable. (And apparently I can't even ask tech support unless I buy a support package...) Any advice much appreciated. Thanks

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• How to send email from home ip when the email server isn't a designated outbound mail server allocated to BT Retail customers [on hold]

  - by Mr Shoubs

  (I am sys admin!) I can receive email, but when I try to send an email from my home office via our work email server I get the following reply: Your message did not reach some or all of the intended recipients. Subject: Test Sent: 19/08/2014 17:02 The following recipient(s) cannot be reached: 'Joe Blogs' on 19/08/2014 17:02 Server error: '554 5.7.1 Service unavailable; Client host [my-ip-here] blocked using zen.spamhaus.org; http://www.spamhaus.org/query/bl?ip=my-ip-here' I went to that URL and it says the following: Ref: PBL231588 81.152.0.0/13 is listed on the Policy Block List (PBL) Outbound Email Policy of BT Retail for this IP range: It is the policy of BT Retail that unauthenticated email sent from this IP address should be sent out only via the designated outbound mail server allocated to BT Retail customers. Please consult the following URL for details on how to configure your email client appropriately. http://btybb.custhelp.com/cgi-bin/btybb.cfg/php/enduser/cci/bty_adp.php?p_sid=fPnV4zhj&p_faqid=6876 Removal Procedure Removal of IP addresses within this range from the PBL is not allowed by the netblock owner's policy. Going to this URL just says: This site has been disabled for the time being. Does anyone know what I should do to allow me to send emails from my home ip - the site suggests I can configure my email client? (note that I have configured the client to use smtp authentication)

  Read the article

• Small store infrastructure - where to begin?

  - by KevinM1

  It looks like my older brother is about to change jobs - from lawyer to shooting range proprietor - and since I'm the family 'computer guy' I have the task of coming up with and setting up the in-store equipment. Only problem, I don't know how to start or where to look. I'm a web programmer, not an IT specialist. To that end, I figured I should ask the pros. Users: 3 (myself, my brother, and his business partner) Equipment: 1 Windows (likely 7) desktop for POS software, 1 Windows desktop/laptop for backroom use (bookkeeping, etc.) Other: ?? I'm looking for a reliable and, well, idiot-proof way to handle backups. Neither my brother nor his business partner are tech savvy (A web browser, email, MS Word and Excel are about the extent of their knowledge), so I need something they can handle. On-site would be preferable to off-site, given my brother's hesitance to have sensitive business data be handled by an outside source. I'm also looking for a small on-site server. I estimate that, at most, only 2-3 users will need access. A linux solution would keep costs down, but I'm concerned about Windows <- linux interoperability. Would the store security cameras' storage be handled by the security company, or would we have to stream that data to our own server? I know from my own experience with personal security that the company gives/loans a recording device to the home owner, but I'm not sure about business security. I know this sounds like a shopping list, and it's pretty vague. I wish I could give more detail, but between my own ignorance and things not being 100% nailed down on the business end, I'm a bit stuck. At the very least I'd like a nudge - links on a place to start, what to look for, things I need to think about, etc. - for this endeavor. Thanks.

  Read the article

• Setup Firefox to save .pages as .zip automatically

  - by Mike Dtrick

  What do I want to do? I would like Firefox to save files with the .pages extension as .zip files automatically. Scenario You are browsing through your emails and you notice your friend just sent you an email with a file attached (a .pages in this example). Unfortunately, you have a laptop that runs Windows. Your friend continues to send tons of emails with .pages files attached and you are tired of manually saving the files as a .zip file. Ultimately, you would like Firefox to be set up so that the download/file manager recognizes the .pages extension and automatically converts it to a .zip file. What have I done? I have saved files manually by selecting save as "All Files" and setting the extension to .zip. I've gone through Firefox and their documentation and have not found anything on how to complete this task. Why am I doing this? To save time (only a few seconds, not the main reason). I would like to setup a simple solution that "converts" a file automatically without having to recall steps on how to achieve the task manually (for clients who aren't exactly tech savvy). So that clients with Windows can access the files. IMPORTANT NOTE: I am not trying to save the web page, rather an Apple document equivalent to Microsoft Word. UPDATE: The really easy method would be to save one file, right click it, choose properties and open all .pages files up with WinRAR (or any other program that extracts files from a compressed folder). For the sake of learning, I am going to "neglect" this method and continue to do some research on Firefox add-ons. I would still like to have Firefox or the download manager to do the bulk of the work for converting the file.

  Read the article

• Unable to ping gateway via bridge nic

  - by Ara

  I'm trying to install KVM on Ubuntu 12.04 server. We have multiple nic on this server of which we primarily use eth0. The server network runs fine(i'm able to ping gateway, ping dns server and ping servers on internet) with eth0 /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local I installed bridge-utils and configured br0 as below /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off Post which i'm able to ping servers on the same ip range 192.168.22.2-254 except for 192.168.22.1 (which is the gateway) also i'm not able to ping any other servers. I'm not able to ping this machine from network. The output for route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.22.1 0.0.0.0 UG 100 0 0 br0 192.168.22.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 I've been struggling with this issue for past 5 days, would be of help if anyone can point me in the right direction to fix this issue. Thanks in advance

  Read the article

• EMC VNX iSCSI setup - unsure about SP/port assignment

  - by pauska

  We have a new VNX5300 waiting to get configured, and I need to plan out the network infrastructure before the EMC tech arrives. It has 4x1gbit iSCSI per SP (8 ports in total), and I'd like to get the most out of the performance until we jump over to 10gig iSCSI. From what I can read from the docs - the recommendation is to use only two ports per SP, with 1 active and 1 passive. Why is this? It seems kind of pointless to have quad-port i/o-modules and then recommend to not use more than two of them? Also - I'm a bit unsure about the zoning. The best practices guide state that you should separate each port on each SP from each other on different logical networks. Does this mean that I have to create 4 logical networks to be able to use all 8 ports? It also gives the following example: Does this mean that A0 and B0 should sit on the same physical switch aswell? Won't this make all traffic go on one switch (if both A1 and B1 are passive)? Edit: Another brainpuzzle I don't get it - each host (as in server) should not have more iSCSI bandwidth available than the storage processor. What on earth does this matter? If serverA have 1gbit and serverB have 100mbit, then the resulting bandwith between them is 100mbit. How can this result in some kind of oversubscription? Edit4: Wait, what. Active and passive ports? The VNX runs in a ALUA configuration with asymmetrical active/active.. there shouldn't be any passive ports, only preferred ones..

  Read the article

• Issues using gmail with google apps and external domain

  - by Jonathan Kelly

  I have recently tried to use gmail through google apps as my main email client, but I'm experiencing a few different problems. I am managing the domain (conjunktiondesign.co.uk) through 123reg.co.uk but it is hosted through fasthosts.co.uk. I transfered the domain to 123reg as fasthosts did not allow me to change the MX records myself. I followed the setup instructions step by step on google apps and changed the MX records as they told me to. My email was now working perfectly but my website was down and I was getting the following error: The dnsserver returned: No DNS records I have a friend that is using the same system as me (ie. Externally hosted domain and google apps mail) and I changed my 123reg details to the same that he had (as his was working perfectly - both email and website). I changed my name servers to point to fasthosts, rather than 123reg and I added an A record called '@' pointing to fasthosts IP address. I also created another A record called 'www' pointing to fasthosts IP address. After I did this, my website worked almost immediately but I have only realised that since changing it my email is now down. I have not received anything since Saturday. I am a web designer and would consider myself fairly tech savvy, but I have no idea about A records, CNAME's and all the things I have been messing about with! What I ultimately need is someone to help me get my email and website working at the same time, rather than one being down when the other is OK. I seem only able to get one or the other working. I have now changed the name servers back to 123reg in an attempt to get my email back as it is more important than my website at this stage. Any help is much appreciated. Thanks.

  Read the article

• Sharing a folder with Nautilus and NTFS external drive gets errors

  - by TheLQ

  I am trying to share a folder in Lubuntu over a network that's on an external NTFS drive. Due to the system that I have (rotating backup disks) this is probably the second time that the drive would of been mounted. Its manually mounted with a simple (for example) mount /dev/sdb1 /media/BACKUP On an internal NTFS disk I have successfully setup a network share and can access it. However on the external disk I can't from any other Windows computer. When setting up the share Nautilus said that it needs to change the other's permissions to allow for other users to write. However afterwords its still blank. Changing it to Read and Write just changes back to blank. Chowning the entire /media folder recursively and trying didn't work. Running PCManFM as root and changing didn't work. Adding "public=yes" to smb.conf and restarting didn't work. I'm out of idea's on what to do. What's weird is that it worked just fine on an internal NTFS disk, so why not the external one? Any solutions need to be able to managed inside of a gui (preferably Nautilus) as the person managing the machine isn't as tech savvy. Thanks

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >