Search Results

Search found 906 results on 37 pages for 'andy levesque'.

Page 12/37 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • 'Relaunching tuncfg' keeps showing up in my console

    - by Andy
    I was scanning my Mac OS X with sophos antivirus and opened the console. I see this over and over again. How do I tell whatever it is to stop trying to launch tuncfg? I recently reinstalled my operating system because I accidentally messed up some key library for using the terminal when trying to install macruby. 3/13/11 11:27:32 PM com.hamachix.tuncfgd[856] /usr/sbin/tuncfgrelaunch: line 8: tuncfg:: command not found 3/13/11 11:28:32 PM com.hamachix.tuncfgd[865] Relaunching tuncfg 3/13/11 11:28:32 PM com.hamachix.tuncfgd[865] /usr/sbin/tuncfgrelaunch: line 8: tuncfg:: command not found 3/13/11 11:29:32 PM com.hamachix.tuncfgd[875] Relaunching tuncfg 3/13/11 11:29:32 PM com.hamachix.tuncfgd[875] /usr/sbin/tuncfgrelaunch: line 8: tuncfg:: command not found

    Read the article

  • How to erase a SSD to restore factory performance in Linux?

    - by Andy B
    Due to big performance issues with an mdraid-1 array I'd like to pull down from the array one of the devices (Samsung 840 Pro), erase it to restore factory performance and re-add it to the array. The reason I want to do this to one of the SSDs is because the poor performance seems to be related to one specific SSD out of the two (although they are the same brand, model and firmware ver). But how do I erase a SSD from Linux? I mention that hdparm indicates that both drives are frozen at this time. Maybe because they are part of an md array? Thanks in advance!

    Read the article

  • what determines the bios you can use

    - by andy
    I have a Compaq sr5710f with a MCP61PM-HM (Iris8) motherboard and loaded a Geforce6100sm-m bios on to it. It works fine and opened up some options, but I want to give my comp am3 socket support. So my question is if I go looking for a bios that will do that for me what do I need to pay attention to. Is it only the chip set which is geforce 6150se nforce 405 or are there more things I should be looking at. If anyone thinks they might know a bios that will help me out that would be good to. I am looking for a retail bios though. I do not want to load any of the experimental ones you can find on the net. Also I would need it to support ddr2 800 ram, and would like to keep am2 support to. I know my bios is data that is downloaded onto my motherboard, or for lack of a better word a program. I am currently running a bios that is not for my motherboard, so I know it can be done. What I need is what do I need to pay attention to when looking for compatible bios programs, that is not for my motherboard.

    Read the article

  • Configuring ejabberd on ubuntu ami of amazon ec2

    - by andy
    This is my first experience with ejabberd. Spare me if I miss anything. I have installed ejabberd server on ubuntu 12.04 AMI on Amazon EC2. I have successfully installed the server, added the admin user and host in the config file and opened up reqd ports (5222, 5223, 5269, 5280). Now I tried to login the web admin interface using the admin user id and password. I could log in, BUT I could only see one section, Virtual Hosts. No Control Lists, Access rules, Nodes and Statistics Menu items on the left. Also, when I click Virtual Hosts Menu item, the page that comes up does not show anything. Here are the screenshots

    Read the article

  • Dynamically loading chef recipies from URLs

    - by andy
    I'm deploying a web app on AWS. I intend to use chef to build AMIs which I'll then put into production. I want to have Chef monitor a URL stored in simpleDB. The URL would point to a tarball in S3. There would be different URLs, one for a config tarball, one for a code tarball. When I update the URL in simpleDB, I want chef to spot this and pull in and apply the configs/deploy the code. Is this possible? Has anything like this been done before or would I need to roll my own code? I think Chef can monitor URLs, but how would be the best way of getting it to load that URL from simpleDB?

    Read the article

  • microsoft mouse and keyboard center doesn't show my mouse

    - by Andy
    as part of a recent windows update, the irritating and intrusive intellipoint microsoft mouse software now seems to have been replaced by the even more irritating and intrusive "microsoft mouse and keyboard center[sic]" I am left handed and need to switch the left and right mouse buttons round. the option to do this has disappeared from the mouse control panel, to be replaced by a link which opens up said mouse and keyboard center. this in turn is a window which allows me to change settings on the keyboard but does not have any way to control mouse settings any hints would be very welcome. this is driving me nuts.

    Read the article

  • Dual DVI external monitors from laptop using HDMI

    - by Andy Evans
    I know there may be a few questions similar to this, but my question is regarding specific hardware configuration. I have an Asus U52f laptop with an HDMI out that I currently use to drive my 24" DVI external monitor. My question is I found an HDMI - dual DVI splitter here and was wanting to know is has anyone tried this type of configuration or would the Matrox DualHead2Go be a better solution.

    Read the article

  • Internet Explorer 8 Viewing PDF files vs saving them

    - by Andy Evans
    I have a user asking about viewing PDF files in Internet Explorer. When she clicks the file link on a website, IE prompts her to save the file, which she then has to open to read. What she's not seeing in the prompt is the ability to open the file without having to save it, or, just opening the PDF automatically. She and a few others are having the same problem, while a majority of the user do not have this problem. All of the users have IE 8 and Adobe Reader 9 installed. I've verified that Adobe Reader's "Display PDF in browser" option is enabled. What else should I check?

    Read the article

  • How can I join non-consecutive partitions on internal hard disk?

    - by Andy
    I recently installed a new, larger hard disk in my PC at work (the office wouldn't spring for an upgrade for my 75GB disk, so I brought my own 2TB disk in from home). I managed to clone the original drive using CloneZilla, but now I have a 75GB partition on my new drive, followed by a 300MB partition, followed by a 1794.65GB of unallocated space. What I want is to add the unallocated space to the 75GB partition, thereby maximizing my C: drive. However, when I right-click on the C: partition, the option to "Extend Volume" is grayed out. How do I get all my fancy new extra space to be part of my C: drive? I also tried booting with GParted, but I get the same deal - cannot adjust the C: drive because there's no contiguous space.

    Read the article

  • PHP displays blank white page even with all error reporting enabled

    - by Andy Shinn
    I am trying to debug a broken page in a Drupal application and am having a hard time getting PHP to spit anything useful out. I have the following set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On error_log = /var/log/php/php_error.log I have a file showing me phpinfo() which confirms these variables are set correctly for the environment. I have increased memory_limit to 256M (which should be more than enough). Yet, the only indication I get is a status 500 code in the apache access log and a blank white page from PHP. The Apache virtual host has LogLevel set to debug and the error log only outputs: [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 0 to 2 : URL /index.php, referer: http://ec2-174-129-192-237.compute-1.amazonaws.com/admin/reports/updates [Sat Jun 16 20:03:03 2012] [error] [client 173.8.175.217] File does not exist: /var/www/favicon.ico [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 42 to 44 : URL /favicon.ico The PHP error log outputs nothing at all. kernel and syslog show nothing related to Apache or PHP. I have also tried installing suphp and checking its log just confirms the user is executing correctly: [Sat Jun 16 20:02:59 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 [Sat Jun 16 20:05:03 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 This is on Ubuntu 12.04 x86_64 with the following PHP modules: ii php5 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.3.10-1ubuntu3.1 command-line interpreter for the php5 scripting language ii php5-common 5.3.10-1ubuntu3.1 Common files for packages built from the php5 source ii php5-curl 5.3.10-1ubuntu3.1 CURL module for php5 ii php5-gd 5.3.10-1ubuntu3.1 GD module for php5 ii php5-mysql 5.3.10-1ubuntu3.1 MySQL module for php5 So, what am I missing here? Why no error reporting?

    Read the article

  • ffmpeg: video file played OK on Ubuntu, but no sound on XP

    - by Andy Le
    I created a video clip using ffmpeg (vcodec: mpeg2video, acodec: AC3 5.1). The file can be played normally on Ubuntu, but when I play it on an XP machine, there is no sound. I can play AC3 files and other movies with AC3 sound. I already tried many codec packs and many players. When I compare the MediaInfo tab of the Properties window of the file with another playable movie, I see that the Audio Identifier of the audio stream in my file is 0x80 while it is 0x02 in the other movie. So I guess that's why players on XP can't recognize the audio codec. When I use an MKV container instead of MPEG (still mpeg2video codec), then the result is OK on both Ubuntu and XP (with the correct Audio ID). I really need MPEG though. Any idea? This is the command I used: ~/ffmpeg/ffmpeg/ffmpeg -loop_input \ -t 97 -r 30000/1001 -i v%4d.tga -i final.ac3 \ -vcodec mpeg2video -qscale 1 -s 400x400 -r 30000/1001 \ -acodec copy -y out6.mpeg 2 This is the output of mediainfo (on Ubuntu): General Complete name : out6.mpeg Format : MPEG-PS File size : 6.86 MiB Duration : 1mn 37s Overall bit rate : 593 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@Main Format settings, BVOP : No Format settings, Matrix : Default Format_Settings_GOP : M=1, N=12 Duration : 1mn 37s Bit rate mode : Variable Bit rate : 122 Kbps Width : 400 pixels Height : 400 pixels Display aspect ratio : 1.000 Frame rate : 29.970 fps Resolution : 8 bits Colorimetry : 4:2:0 Scan type : Progressive Bits/(Pixel*Frame) : 0.025 Stream size : 1.41 MiB (21%) Audio ID : 128 (0x80) Format : AC-3 Format/Info : Audio Coding 3 Duration : 1mn 36s Bit rate mode : Constant Bit rate : 448 Kbps Channel(s) : 6 channels Channel positions : Front: L C R, Side: L R, LFE Sampling rate : 44.1 KHz Stream size : 5.18 MiB (75%)

    Read the article

  • Solaris TCP/IP performance tuning

    - by Andy Faibishenko
    I am trying to tune a high message traffic system running on Solaris. The architecture is a large number (600) of clients which connect via TCP to a big Solaris server and then send/receive relatively small messages (.5 to 1K payload) at high rates. The goal is to minimize the latency of each message processed. I suspect that the TCP stack of the server is getting overwhelmed by all the traffic. What are some commands/metrics that I can use to confirm this, and in case this is true, what is the best way to alleviate this bottleneck? PS I posted this on StackOverflow originally. One person suggested snoop and dtrace. dtrace seems pretty general - are there any additional pointers on how to use it to diagnose TCP issues?

    Read the article

  • Server reboots every 4.5-5.5 minutes...

    - by Andy
    Hi, I've recently installed a server in colocation, and my server is rebooting every 4.5-5.5 minutes. Regardless of the OS I run, it reboots. I have all ECC memory in the server, so it should correct errors if there is a bad bit in the memory, right? It's weird because it always happens about 4.5-5.5 minutes after bootup. My motherboard is a Supermicro X8DTL-iF. I read on a blog that another person had the problem, and supermicro recommended to do a BIOS update. Is this the right course of action?

    Read the article

  • Various problems with software raid1 array built with Samsung 840 Pro SSDs

    - by Andy B
    I am bringing to ServerFault a problem that is tormenting me for 6+ months. I have a CentOS 6 (64bit) server with an md software raid-1 array with 2 x Samsung 840 Pro SSDs (512GB). Problems: Serious write speed problems: root [~]# time dd if=arch.tar.gz of=test4 bs=2M oflag=sync 146+1 records in 146+1 records out 307191761 bytes (307 MB) copied, 23.6788 s, 13.0 MB/s real 0m23.680s user 0m0.000s sys 0m0.932s When doing the above (or any other larger copy) the load spikes to unbelievable values (even over 100) going up from ~ 1. When doing the above I've also noticed very weird iostat results: Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 1589.50 0.00 54.00 0.00 13148.00 243.48 0.60 11.17 0.46 2.50 sdb 0.00 1627.50 0.00 16.50 0.00 9524.00 577.21 144.25 1439.33 60.61 100.00 md1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 md2 0.00 0.00 0.00 1602.00 0.00 12816.00 8.00 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 And it keeps it this way until it actually writes the file to the device (out from swap/cache/memory). The problem is that the second SSD in the array has svctm and await roughly 100 times larger than the second. For some reason the wear is different between the 2 members of the array root [~]# smartctl --attributes /dev/sda | grep -i wear 177 Wear_Leveling_Count 0x0013 094% 094 000 Pre-fail Always - 180 root [~]# smartctl --attributes /dev/sdb | grep -i wear 177 Wear_Leveling_Count 0x0013 070% 070 000 Pre-fail Always - 1005 The first SSD has a wear of 6% while the second SSD has a wear of 30%!! It's like the second SSD in the array works at least 5 times as hard as the first one as proven by the first iteration of iostat (the averages since reboot): Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 10.44 51.06 790.39 125.41 8803.98 1633.11 11.40 0.33 0.37 0.06 5.64 sdb 9.53 58.35 322.37 118.11 4835.59 1633.11 14.69 0.33 0.76 0.29 12.97 md1 0.00 0.00 1.88 1.33 15.07 10.68 8.00 0.00 0.00 0.00 0.00 md2 0.00 0.00 1109.02 173.12 10881.59 1620.39 9.75 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.41 0.01 3.10 0.02 7.42 0.00 0.00 0.00 0.00 What I've tried: I've updated the firmware to DXM05B0Q (following reports of dramatic improvements for 840Ps after this update). I have looked for "hard resetting link" in dmesg to check for cable/backplane issues but nothing. I have checked the alignment and I believe they are aligned correctly (1MB boundary, listing below) I have checked /proc/mdstat and the array is Optimal (second listing below). root [~]# fdisk -ul /dev/sda Disk /dev/sda: 512.1 GB, 512110190592 bytes 255 heads, 63 sectors/track, 62260 cylinders, total 1000215216 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00026d59 Device Boot Start End Blocks Id System /dev/sda1 2048 4196351 2097152 fd Linux raid autodetect Partition 1 does not end on cylinder boundary. /dev/sda2 * 4196352 4605951 204800 fd Linux raid autodetect Partition 2 does not end on cylinder boundary. /dev/sda3 4605952 814106623 404750336 fd Linux raid autodetect root [~]# fdisk -ul /dev/sdb Disk /dev/sdb: 512.1 GB, 512110190592 bytes 255 heads, 63 sectors/track, 62260 cylinders, total 1000215216 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003dede Device Boot Start End Blocks Id System /dev/sdb1 2048 4196351 2097152 fd Linux raid autodetect Partition 1 does not end on cylinder boundary. /dev/sdb2 * 4196352 4605951 204800 fd Linux raid autodetect Partition 2 does not end on cylinder boundary. /dev/sdb3 4605952 814106623 404750336 fd Linux raid autodetect /proc/mdstat root # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdb2[1] sda2[0] 204736 blocks super 1.0 [2/2] [UU] md2 : active raid1 sdb3[1] sda3[0] 404750144 blocks super 1.0 [2/2] [UU] md1 : active raid1 sdb1[1] sda1[0] 2096064 blocks super 1.1 [2/2] [UU] unused devices: Running a read test with hdparm root [~]# hdparm -t /dev/sda /dev/sda: Timing buffered disk reads: 664 MB in 3.00 seconds = 221.33 MB/sec root [~]# hdparm -t /dev/sdb /dev/sdb: Timing buffered disk reads: 288 MB in 3.01 seconds = 95.77 MB/sec But look what happens if I add --direct root [~]# hdparm --direct -t /dev/sda /dev/sda: Timing O_DIRECT disk reads: 788 MB in 3.01 seconds = 262.08 MB/sec root [~]# hdparm --direct -t /dev/sdb /dev/sdb: Timing O_DIRECT disk reads: 534 MB in 3.02 seconds = 176.90 MB/sec Both tests increase but /dev/sdb doubles while /dev/sda increases maybe 20%. I just don't know what to make of this. As suggested by Mr. Wagner I've done another read test with dd this time and it confirms the hdparm test: root [/home2]# dd if=/dev/sda of=/dev/null bs=1G count=10 10+0 records in 10+0 records out 10737418240 bytes (11 GB) copied, 38.0855 s, 282 MB/s root [/home2]# dd if=/dev/sdb of=/dev/null bs=1G count=10 10+0 records in 10+0 records out 10737418240 bytes (11 GB) copied, 115.24 s, 93.2 MB/s So sda is 3 times faster than sdb. Or maybe sdb is doing also something else besides what sda does. Is there some way to find out if sdb is doing more than what sda does? UPDATE Again, as suggested by Mr. Wagner, I have swapped the 2 SSDs. And as he thought it would happen, the problem moved from sdb to sda. So I guess I'll RMA one of the SSDs. I wonder if the cage might be problematic. What is wrong with this array? Please help!

    Read the article

  • How to access a port via OpenVpn only

    - by Andy M
    I've set up an openvpn server alongside an apache website that can only be accessed on port 8100 on the same machine. My /etc/openvpn/server.conf file looks like this: port 1194 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/server.crt key ./easy-rsa2/keys/server.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem # Diffie-Hellman parameter server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt # make sure clients can still connect to the internet push "redirect-gateway def1 bypass-dhcp" keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 Now I tried to let only clients connected to the vpn network access the website on apache via port 8100. So I defined a few iptables rules: #!/bin/sh # My system IP/set ip address of server SERVER_IP="192.168.0.2" # Flushing all rules iptables -F iptables -X # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP # Allow incoming access to port 8100 from OpenVPN 10.8.0.1 iptables -A INPUT -i tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # outgoing http iptables -A OUTPUT -o tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT Now when I connect to the server from my client computer and try to access the website on 192.168.0.2:8100, my browser can't open it. Will I have to forward traffic from tun0 to eth0? Or is there anything else I'm missing?

    Read the article

  • Create account for service

    - by Andy
    I am configuring a new server. The server is running Hudson that is going to copy some files from this server to another. The other server is a virtual machine. Both running Windows Server 2012. Hudson is started on server A with log on as "Local System". When I come to the copy phase it says "Access denied". Changing the log on to "Administrator" works. However, I guess this is bad. I do not have much experience with user management. I tried to create a own hudson account on both servers A and B. I tried to log on as hudson account in the service-management but it doesn't start. How would you create an account for this particular service that has access to the shared folder on server B and can be used to start the service on server A? I guess I need two accounts with same username and password on server A and server B? The folder on Server B is shared with everyone and the guest account is enabled.

    Read the article

  • Windows 8 Fails to install with corrupted graphics

    - by Andy
    I am trying to install Windows 8 Pro Upgrade via the download method on an older PC (07-08). It is a Dell Dimension E521 but it has been upgraded with a 3.0 Ghz Dual Core AMD Processor, 120 GB SSD, and 4 GB of RAM. The Windows 8 upgrade assistant did not detect any issues or concerns with upgrading other than I don't have DVD software installed. The system install Windows 8 but on the first boot, corrupt graphics are present. Eventually, the monitor will go into sleep mode and then roll back to Windows 7 Pro X64 which runs fine. I wouldn't be upset over not being able to install Windows 8, but I already paid for the software since I thought there would be no issues upgrading. The Graphics card in the system is the Geforce 7300LE and it has the latest NVidia drivers for Windows 7 loaded. I saw this solution which is similar to my problem: Corrupt graphics during Windows 8 installation However, I have downloaded Windows 8 and I am not sure how to go about modifying the install that resides somewhere on the hard drive. Thanks in advance for any assistance.

    Read the article

  • How to prevent asymmetric routing with multiple eBGP routers?

    - by Andy Shinn
    I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

    Read the article

  • Map a drive to root of a server (\\sever) in Vista

    - by Andy T
    Hi, In Win XP, I can very easily map a network drive to the root of my NAS server. I browse to it in Explorer (\192.168.1.70), choose "Map Network Drive", choose the drive letter, done. In Vista, this does not seem possible. I have to go "Map Network Drive" from 'Computer', then enter the address, but it will only let me map to specific shares (sub-folders off of the server root) and NOT to the server root share. Since my NAS has built-in shares (music, photo, video, etc.) then I would have to have drive letters for all of these, which I absolutely don't want. Can anyone tell me - how come I can easily map to the server root from XP, but not in Vista? Is there something fundamentally different in the networking across the two OS's? Or do I just need to do things a different way? Hope someone can help. Thanks, AT

    Read the article

  • How can I debug Cisco Firewall ASA "Dispatch Unit" very high CPU utilisation from ASDM?

    - by Andy
    I have recently had my first firewall installed so I am very new to this whole situation. I am finding that Dispatch unit is becoming overloaded and it would appear to be the reason I get serious bouts of lag on my server. The firewall has had little configuration apart from me blocking all the ports in "Access Rules" and allowing only the ones the server needs and from where it needs them. I guess what I am after is assistance with locating the issues causing "Dispatch Unit" to take up all the CPU Regards --Edit-- With ASDM statistics I found that packets inbound (peak of 70-100k/sec from <1k/sec normal), traffic inbound (peak of 40-50kbits/sec from <1kbits/sec normal) and CPU all peak at the same time so I am pretty sure it is an attack of some sort but as a beginner with ASA I am not sure how to resolve

    Read the article

  • How do I count the times each number appears in columns of numbers?

    - by Andy C.
    I am sure this must be easy, but I am inexperienced. About the best way to think of my problem is to think of it as trying to sort and then count lottery numbers. To stay simple, let's do a Pick 3 game. Let's look at 10 drawings. I would split each drawn number into a separate column: DATE BALL#1 BALL#2 BALL#3 3/1 1 3 5 3/2 3 7 8 3/3 2 2 1 3/4 5 7 6 3/5 2 3 1 3/6 0 5 9 3/7 3 7 0 3/8 6 8 4 3/9 2 4 3 3/10 7 1 2 I would like to be able to build formulas into cells that would tell me how many times each number appeared overall, and how many times each number appeared in the position it occurred. Like this (using the above example): Number Overall Count Ball#1 Count Ball#2 Count Ball#3 Count 0 2 1 0 1 1 4 1 1 2 (That is, The number zero appears twice overall, and came up once as the first number drawn; zero times as the middle ball; and once as the third ball. Likewise, the number 1 was drawn four times in our 10-day period. It was the first ball once, the second ball once and the third ball twice.) And so on. All help appreciated. I have access to Excel and Microsoft Works, or of course if there is a Google Docs way to handle this All thanks for any help.

    Read the article

  • USB Hub powers down in sleep mode on Win 7 64

    - by Andy B
    This question has been asked before but not answered. I would like the USB hub to remain on in sleep so I can wake up the laptop from an external keyboard and mouse. I have set all the device drivers by unchecking allow this device to be powered down and disabled selective suspend in control panel but the hub still powers down. If I plug a keyboard or mouse directly in to the PC they remain powered and wake the computer its only when they are connected through the hub there is a problem. I have another PC running Win 7 32. If I set this up in exactly the same way the hub remains powered in sleep. Both PC's are Toshiba Satellites with multi-core celerons but one runs Win 7 32 the other Win 7 64. BIOS settings are the same. Any help would be appreciated even confirmation that this is a feature of Win 7 64.

    Read the article

  • How to set up a DNS name server to always resolve to a constant IP address for every request

    - by Andy Higgins
    I am looking for a simple DNS name server set up to always return the same IP address no matter what the request is. The reason for this is we are a domain registrar and when a domain is first registered we need it to have valid name servers (and don't want to have to first create name server records before registering a domain). We will then subsequently change the name server records after the domain has been registered. I assume this is possible to do with bind but was wondering if there might be a simpler solution available using one of the more light weight name servers out there? Any suggestions on how to accomplish this in a simple manner will be appreciated.

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >