Search Results

Search found 1193 results on 48 pages for 'cisco pix'.

Page 12/48 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Balancing internal services using a Cisco CSS 11501

  - by Ladadadada

  First, the background to the problem: I have a Cisco CSS11501 that I am using to load balance a few web servers. These web servers have two network interfaces, one internal and one external and we are sending the requests to the internal interface. We have the CSS configured to do NAT because our webservers need to see the client's IP address. Because the TCP packets hit the webservers with a source address on the Internet, the webserver tries to send the packet back to the client over the external interface and not through the load balancer. In order to stop these requests being sent back out to the Internet via the external interface, we added a routing rule on these boxes so that all traffic with a source address on the internet will use the load balancer as the gateway. This part works fine. What I would also like to to is use the CSS as a load balancer for internal services such as our MySQL slaves. When I do this, I run into a similar problem; the TCP connection goes from the web server to the load balancer and then from the load balancer to the MySQL slave but the CSS spoofs a source address of the original webserver. The MySQL slave then tries to send the response directly to the webserver via the internal network and not via the load balancer. The ideal solution would be to tell the CSS not to do source address spoofing on the internal network and only do it for requests originating on the Internet. Is this possible ? Failing that, is there a way of directing the load balanced traffic back through the load balancer while keeping the other traffic (say SSH) purely on the internal network ? Is there another way of using the CSS11501 to load balance internal services ?

  Read the article

• AnyConnect SSL VPN split tunneling for a single website?

  - by Daniel Lucas

  We have a Cisco ASA 5510. We use split tunneling for AnyConnect SSL VPN clients. All internal addresses are tunnelled. Everything else is routed through the client's own internet connection. We use a SaaS service that only responds to requests when they come from one of our own public IP addresses. Because of this, VPN users are unable to access it currently. Is there a way to specify that a specific website should be tunneled and all others should not? NOTE: Worst case we will use a web bookmark on the clientless portal to tranlate through our network, but I'd like to see if the above is possible first.

  Read the article

• NAT confusion regarding cisco ASA5510

  - by LonelyLonelyNetworkN00b

  I'm setting up my first cisco firewalls. A little information first:I have two asa5510 setup in a working active/standby pair. From my ISP i have two public subnets. A /29 and a /26. On my DMZ interface i have the /26 configured. On my WAN Interface i have configured the /29 IPs. My isp routes the /26 via the /29 primary IP. I'm running ASA 8.2. I've turned NAT-Control off, because i don't want to use nat for for other than some internal interfaces. In essence i don't want to use NAT unless i specify it. I have a internal interface with the network of 192.168.100.0/24. I've tried setting up nat limke this: nat (inside) 1 192.168.100.0 255.255.255.0 global (WAN) 1 interface I was under the impression that this would let connections that was going from 192.168.100.0/24 and out the WAN interface to be Port-Address-translated. I'm not getting this to work for some reason. Inside interface has security level of 100, and wan has security level of 0.

  Read the article

• Cisco IOS BVI ACL: Only allow established UDP

  - by George Bailey

  Related: Cisco IOS ACL: Don't permit incoming connections just because they are from port 80 I know we can use the established keyword for TCP.. but what can we do for UDP (short of replacing a Bridge or BVI with a NAT)? Answer I found out what "UDP has no connection" means. DNS uses UDP for example.. named (DNS server) is lisenting on port 53 nslookup (DNS client) starts listening on some random port and sends a packet to port 53 of the server and notes the source port in that packet. nslookup will retry 3 times if necessary. Also the packets are so small that it does not have to worry about them coming in the wrong order. If nslookup receives a response on that port that comes from the servers IP and port then it stops listening. If the server tried to send two responses (for example a response and a response to the retry) then the server would not care if either of them made it because the client has the job to retry. In fact.. unless ICMP 3/3 packet gets through the server would not know about a failure. This is different from TCP where you get connection closed or timed out errors. DNS allows for an easy retry from the client as well as small packets.. so UDP is an excellent choice because it is more efficient. In UDP you would see nslookup sends request named sends answer In TCP you would see nslookup's machine sends SYN named's machine sends SYN-ACK nslookup's machine sends ACK and the request named's machine sends the response That is much more than is necessary for a tiny DNS packet

  Read the article

• Clarification for setting up SSH terminal access on Cisco IOS

  - by Matt Malesky

  I'm attempting to set up SSH on a Cisco 2811 and having some difficulties. The first step to this should be running crypto key generate rsa I seem to be missing this though: better#crypto key generate rsa ^ % Invalid input detected at '^' marker. better# Furthermore, the only available commands I have in the crypto key namespace are lock and unlock, which seem to indicate a locked keypair (for which I don't know the password): better#crypto key ? lock Lock a keypair. unlock Unlock a keypair. better#crypto key unlock ? rsa RSA keys better#crypto key unlock rsa %% Please enter the passphrase: %% Unlocking failed. . better# More or less, I'm asking what exactly this might mean, and if I actually do have certificates already here (used router)? Otherwise, how can I solve this? It's my first time configuring this feature, but I definitely believe it's part of my IOS. Speaking of my IOS, I'm running the image c2800nm-advsecurityk9-mz.124-24.T6.bin I'll also note that I have my hostname and ip domain-name configured. I'll also give you a dir flash: below if it's at all of use: better#dir flash: Directory of flash:/ 2 -rw- 2748 Jul 27 2009 14:03:52 +00:00 sdmconfig-2811.cfg 3 -rw- 931840 Jul 27 2009 14:04:10 +00:00 es.tar 4 -rw- 1505280 Jul 27 2009 14:04:32 +00:00 common.tar 5 -rw- 1038 Jul 27 2009 14:04:46 +00:00 home.shtml 6 -rw- 112640 Jul 27 2009 14:05:00 +00:00 home.tar 7 -rw- 1697952 Jul 27 2009 14:05:26 +00:00 securedesktop-ios-3.1.1.45-k9.pkg 8 -rw- 415956 Jul 27 2009 14:05:46 +00:00 sslclient-win-1.1.4.176.pkg 9 -rw- 38732900 Dec 8 2011 06:28:56 +00:00 c2800nm-advsecurityk9-mz.124-24.T6.bin 64016384 bytes total (20598784 bytes free) better#

  Read the article

• Cisco BVI: Claiming IP addresses

  - by cjavapro

  I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• ASA5500 series logging for management interface in transparent mode

  - by ANervousTwitch

  i have a cisco asa5520 in transparent mode. the interface is on the same subnet as some windows machines, which are generating a lot of broadcast traffic that is filling up the logs. is there any way to have it not log that its blocking those packets? its a bunch of these messages: "through-the-device packet to from management-only network is denied: udp src..." im also seeing some of those zeroconf requests that id like to drop logging for. i tried to just put a rule on the management interface, but apparently thats not allowed.

  Read the article

• Cisco IOS ACL: Don't permit incoming connections just because they are from port 80

  - by cjavapro

  I am going much based on my memory and I may not be correct on all of this. On a Cisco 851 (IOS) that uses a BVI or a bridge-route (the servers on the inside are configured with static and public IP addresses). I would apply two access lists (both end with deny ip any any log) on FastEthernet4 (the WAN port). There would be one for FA4 in and another for FA4 out. FA4 out would have a line like access-list 110 permit 98.76.54.0 0.0.0.255 gt 1023 any eq http I think this means from 98.76.54.* with a from port of at least 1024 can connect to any other machine with a destination port 80. So, then I have to allow the response to the HTTP connection. FA4 in would have a line like access-list 120 permit any eq http 98.76.54.0 0.0.0.255 gt 1023 Now the problem with that is that anybody on the outside can set their from port to port 80 and then connect to any inside port that is at least 1024. How do we prevent this and require the incoming data to be a response to the outgoing data.

  Read the article

• Cisco Call Manager adding 7945's

  - by Will

  Hello we currently have a call manager settup (older we are working on upgrading it) but for now we are looking to add 7945 IP phones. We currently have 7960's all over the place, but we can't get these new anymore. Here is the info about our call manager ace.dll 5.2.5.0 CCM4.1(3) aced.dll CCM4.1(3) AdministrativeReportingTool.exe 4.1(0.45) 4.1(3)sr4d Apache Tomcat 4.1 CCM4.1(3) ASTIsapi.dll 3.3.2.0 4.1(3)sr4d AudioTranslator.exe 4.0.0.3 CCM4.1(3) Aupair.exe 4.1.3.10472 4.1(3)sr4d AupairChangeNotify.dll 4.1.0.11 CCM4.1(3) AuthFilt.dll 4.0.0.0 4.1(3)sr4d AVVIDCustomerDirectoryConfigurationPlugin.exe 4.1.0.17(0) CCM4.1(3) bootp.exe 2.0.2.2 CCM4.1(3) BulkAdministrationTool.exe 5.1(4c) 4.1(3)sr4d CallBackService.exe 3.3.2.3 4.1(3)sr4d ccm.exe 4.1.3.17472 4.1(3)sr4d CcmPerfMon.dll 4.1(3)sr4d CCNTEST.EXE CCM4.1(3) cdpintf.dll 4.0.0.0 CCM4.1(3) Cisco CallManager 4.1(3)sr4d 4.1(3)sr4d One of the admins recommenced downloading a device pack, which we did. However when we ran it on the call manager server it gave the error "unable to read script" Any recommendations on how to get these phones working with our Call Manager? Thank you.

  Read the article

• Cisco configuration for public library internet

  - by AlternateZ

  I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

  Read the article

• Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

  - by Brandon Bearden

  Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

  Read the article

• Cisco AnyConnect VPN client - prevent connecting as work network

  - by Opmet

  From Windows 7 I'm using "Cisco AnyConnect Secure Mobility Client 3.0" to connect to our corporate network. Every time I establish the VPN connection Windows will set the type as "work network". I don't want this. So I go to "network and sharing center" and manually / interactively change it to "public network". But I have to repeat it for every new VPN connection. Is there any way to make Windows remember / persist this configuration? Can it be configured in the VPN client? Do our IT admins need to change something at server end? Motivation: A "work network" per default uses different firewall settings that allows for stuff like "network discovery" and "file shares". But I just need "remote desktop" (mstsc). Additional info: Our IT admins claimed this would be Windows default behaviour and there was nothing we could do about it: Windows would always initiate a VPN connection as "work network". Based on this statement I assume this is a "general" issue and went ahead posting here (at superuser.com).

  Read the article

• Cisco 7206vxr cpu reducing

  - by naimson

  I have a 7206VXR (NPE-G2) . At the rate of 140 kpps i gain 80% of cpu . So i looking for ways how to reduce it? So i want to turn off netflow(but don't want to this,monitoring is highly important for me), but it will give me only 10-20% ? At this moment with 84kpps i have 58% sh processes cpu sorted give me this. PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 109 163534600 537236763 304 35.38% 32.83% 16.85% 0 IP Input 67 829396 52280 15864 0.15% 0.01% 0.00% 0 Per-minute Jobs 68 5542736 3053476 1815 0.15% 0.18% 0.16% 0 Per-Second Jobs 51 635852 1116315 569 0.07% 0.03% 0.02% 0 Net Background 329 120396 4607274 26 0.07% 0.00% 0.00% 0 EIGRP-IPv4 Hello 105 50508 95032488 0 0.07% 0.05% 0.05% 0 IPAM Manager 6 4068580 476916 8531 0.00% 0.07% 0.05% 0 Check heaps 7 7768 3634 2137 0.00% 0.00% 0.00% 0 Pool Manager 8 0 1 0 0.00% 0.00% 0.00% 0 DiscardQ Backgro 10 8 708 11 0.00% 0.00% 0.00% 0 WATCH_AFS 5 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers 12 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea 9 0 2 0 0.00% 0.00% 0.00% 0 Timers 11 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio 13 296 610532 0 0.00% 0.00% 0.00% 0 IPC Event Notifi 16 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager 17 3584 2980311 1 0.00% 0.00% 0.00% 0 IPC Periodic Tim 4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN 19 0 1 0 0.00% 0.00% 0.00% 0 IPC Process leve 20 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager 21 96 174453 0 0.00% 0.00% 0.00% 0 IPC Check Queue 14 4 50890 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach 3 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ 24 756 305371 2 0.00% 0.00% 0.00% 0 IPC Keep Alive M 25 2340 610561 3 0.00% 0.00% 0.00% 0 IPC Loadometer 22 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat RX Cont 15 0 1 0 0.00% 0.00% 0.00% 0 IPC Session Serv 18 1620 2980310 0 0.00% 0.00% 0.00% 0 IPC Deferred Por 29 0 1 0 0.00% 0.00% 0.00% 0 Exception contro sh run(greped): http://pastie.org/5483194 Hardware: c7200p-adventerprisek9-mz.151-4.M1.bin Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 2xxxxxxx MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2 6 slot VXR midplane, Version 2.1

  Read the article

• Poor upload/download speed on 2 x ADSL lines into a Cisco 2621XM

  - by 2020mobile

  Hi, Sorry never been on this site before so I apologise if not the right section or even forum. I have users complaining of very slow internetn connectivity on site and have checked with our ISP who have said that the line is testing at 8mb. We have 2 x BT lines that have our ISP broadand on them. Both lines go into a Cisco 2600 series router that then has a PIX firewall off that. Connectivity is successful just gone really slow and unable to download anything. Config is below: version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ROUTER-ADSL-INTERNET ! logging buffered 16384 informational enable secret xxx enable password xxx ! username xxx username xxx clock summer-time UK recurring last Sun Mar 1:00 last Sun Oct 1:00 aaa new-model ! ! aaa authentication login default local aaa authorization exec default local aaa session-id common ip subnet-zero no ip source-route ! ! ! ip audit notify log ip audit po max-events 100 no ip bootp server ip name-server 213.208.106.212 no mpls ldp logging neighbor-changes no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! ! ! ! ! ! ! interface ATM0/0 description 01270 111111 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/0 ip address 82.133.32.9 255.255.255.248 shutdown speed 100 full-duplex no cdp enable ! interface ATM0/1 description 01270 222222 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/1 ip address 217.146.115.49 255.255.255.240 duplex auto speed auto no cdp enable ! interface Dialer0 ip address 217.146.115.250 255.255.255.248 encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap callin ppp chap hostname [email protected] ppp chap password 7 xxxxx ppp multilink ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! no logging trap access-list 10 permit 217.146.115.50 access-list 10 permit 82.133.32.10 access-list 10 deny any access-list 22 permit 217.146.115.50 access-list 22 permit 217.206.239.86 access-list 22 permit 82.133.32.10 access-list 22 deny any dialer-list 1 protocol ip permit no cdp run ! ! snmp-server community xxxxxx RO 10 snmp-server enable traps tty radius-server authorization permit missing Service-Type ! ! ! ! ! ! line con 0 exec-timeout 5 0 password 7 xxxxxx line aux 0 no exec line vty 0 4 access-class 22 in exec-timeout 5 0 password 7 xxxxxx transport input telnet ssh transport output none line vty 5 15 password 7 xxxxxx transport input telnet ssh ! ntp clock-period 17180095 ntp server 130.88.200.98 ! ! end Now my knowledge is very limited but ISP have said that while the lines are bonded each needs a seperate login as they've recently changed their L2TP router and that enforces the use of seperate logins - when the lines were configured we were given two logins. So, my question is what changes do I need to make to the config in order to get this working? it was ok before their change and I do have another login :- 01270 111111 - [email protected] 01270 222222 - [email protected] Apologies for the long email and thanks for taking the time to read it. Any more info I can provide please let me know. Thanks,

  Read the article

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• Cisco ASA SSL VPN options?

  - by JonH

  Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

  Read the article

• Configuring Wireless on Cisco 851W

  - by Aequitarum Custos

  Either a powersurge or something caused our router's configuration to get wiped, and our last backup was before the wireless network was setup. We have not been able to reconfigure the wireless since then, so was curious if anyone here would be able to determine what configuration is needed. We are using a Cisco 851W running 12.4(15)T9 We would like to use WPA encryption, and have it on the same network as the rest of the office network. Config file is below: User Access Verification Building configuration... Current configuration : 3857 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname BOB ! boot-start-marker boot-end-marker ! enable secret 5 ********************* ! no aaa new-model ! ! dot11 syslog no ip source-route ! ! ip cef no ip bootp server ip domain name BOB.com ip name-server 61.11.1.1 ip name-server 61.11.1.2 ! ! ! username BOBB privilege 15 password 7 ************************* ! ! archive log config hidekeys ! ! ip tcp synwait-time 10 ! ! ! interface FastEthernet0 no cdp enable ! interface FastEthernet1 no cdp enable ! interface FastEthernet2 no cdp enable ! interface FastEthernet3 no cdp enable ! interface FastEthernet4 description WAN Connection$ETH-WAN$ ip address 61.11.1.14 255.255.254.0 ip nat outside ip virtual-reassembly duplex auto speed auto no cdp enable ! interface Dot11Radio0 no ip address shutdown ! encryption mode ciphers tkip speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.20 ip access-group Guest-ACL in no cdp enable ! interface Vlan1 description Internal Network ip address 192.168.2.60 255.255.255.0 ip nat inside ip nat enable ip virtual-reassembly ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 61.11.2.14 ! ip http server no ip http secure-server ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended Guest-ACL deny ip any 192.0.0.0 0.0.0.255 permit ip any any ! access-list 1 permit 192.0.0.0 0.0.0.255 access-list 100 remark SDM_ACL Category=2 access-list 100 permit ip 192.0.0.0 0.0.0.255 any no cdp run ! control-plane ! !

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• CISCO Tapi with julmar atapi [closed]

  - by uma

  can we use julmar atapi for accessing cisco tapi/call manager functions?.. Is it a correct way to find solution. How to use cisco tapi with in .net application. Give me any sample code... Thanks in advance.. Sorry for the question with incomplete information. My requirement is, develop the interface for CUCM V8.6 (cisco unified call manager) with asp.net application. we need to communicate with CUCM to get the information about call details and force the user to enter authendication code. i got the information from web is, need C++ wrapper to access Tapi. Julmar Atapi is a free wrapper to access the Tapi. Our client need is , to use CISCO Tapi . My Question is , how to access CISCO Tapi from .Net Application. What is the Requirement? Is Julmar Atapi used to access CISCO Tapi? i want to use cisco FAC(Forced Authorization code) function. how to access this function from my application. Thanks in advance.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Cisco 800 series won't forward port

  - by sam

  Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime service password-encryption no service dhcp ! hostname QUESTMOUNT ! logging buffered 16386 informational logging rate-limit 100 except warnings no logging console no logging monitor enable secret 5 -removed- ! username administrator secret 5 -removed- username manager secret 5 -removed- clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 3:00 aaa new-model ! ! aaa authentication login default local aaa authentication login userlist local aaa authentication ppp default local aaa authorization network grouplist local aaa session-id common ip subnet-zero no ip source-route no ip domain lookup ip domain name quest.local ! ! no ip bootp server ip inspect name firewall tcp ip inspect name firewall udp ip inspect name firewall cuseeme ip inspect name firewall h323 ip inspect name firewall rcmd ip inspect name firewall realaudio ip inspect name firewall streamworks ip inspect name firewall vdolive ip inspect name firewall sqlnet ip inspect name firewall tftp ip inspect name firewall ftp ip inspect name firewall icmp ip inspect name firewall sip ip inspect name firewall fragment maximum 256 timeout 1 ip inspect name firewall netshow ip inspect name firewall rtsp ip inspect name firewall skinny ip inspect name firewall http ip audit notify log ip audit po max-events 100 ip audit name intrusion info list 3 action alarm ip audit name intrusion attack list 3 action alarm drop reset no ftp-server write-enable ! ! ! ! crypto isakmp policy 1 authentication pre-share ! crypto isakmp policy 2 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group staff key 0 qS;,sc:q<skro1^, domain quest.local pool vpnclients acl 106 ! ! crypto ipsec transform-set tr-null-sha esp-null esp-sha-hmac crypto ipsec transform-set tr-des-md5 esp-des esp-md5-hmac crypto ipsec transform-set tr-des-sha esp-des esp-sha-hmac crypto ipsec transform-set tr-3des-sha esp-3des esp-sha-hmac ! crypto dynamic-map vpnusers 1 description Client to Site VPN Users set transform-set tr-des-md5 ! ! crypto map cm-cryptomap client authentication list userlist crypto map cm-cryptomap isakmp authorization list grouplist crypto map cm-cryptomap client configuration address respond crypto map cm-cryptomap 65000 ipsec-isakmp dynamic vpnusers ! ! ! ! interface Ethernet0 ip address 192.168.0.254 255.255.255.0 ip access-group 102 in ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated ip access-group 101 in no ip redirects no ip unreachables ip nat outside ip inspect firewall out ip audit intrusion in encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username -removed- password 7 -removed- ppp ipcp dns request crypto map cm-cryptomap ! ip local pool vpnclients 192.168.99.1 192.168.99.254 ip nat inside source list 105 interface Dialer0 overload ip nat inside source static tcp 192.168.0.2 444 interface Dialer0 444 ip nat inside source static tcp 192.168.0.51 9000 interface Dialer0 9000 ip nat inside source static udp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 25 interface Dialer0 25 ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ip http server no ip http secure-server ! ip access-list logging interval 10 logging 192.168.0.2 access-list 1 remark The local LAN. access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.0.0 access-list 2 remark Where management can be done from. access-list 2 permit 192.168.0.0 0.0.0.255 access-list 3 remark Traffic not to check for intrustion detection. access-list 3 deny 192.168.99.0 0.0.0.255 access-list 3 permit any access-list 101 remark Traffic allowed to enter the router from the Internet access-list 101 permit ip 192.168.99.0 0.0.0.255 192.168.0.0 0.0.0.255 access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit tcp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit tcp host 120.136.2.22 any eq 1433 access-list 101 permit tcp host 123.100.90.58 any eq 1433 access-list 101 permit udp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit udp host 120.136.2.22 any eq 1433 access-list 101 permit udp host 123.100.90.58 any eq 1433 access-list 101 permit tcp any any eq 444 access-list 101 permit tcp any any eq 9000 access-list 101 permit tcp any any eq smtp access-list 101 permit udp any any eq non500-isakmp access-list 101 permit udp any any eq isakmp access-list 101 permit esp any any access-list 101 permit tcp any any eq 1723 access-list 101 permit gre any any access-list 101 permit tcp any any eq 22 access-list 101 permit tcp any any eq telnet access-list 102 remark Traffic allowed to enter the router from the Ethernet access-list 102 permit ip any host 192.168.0.254 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 105 remark Traffic to NAT access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 106 remark User to Site VPN Clients access-list 106 permit ip 192.168.0.0 0.0.0.255 any dialer-list 1 protocol ip permit ! line con 0 no modem enable line aux 0 line vty 0 4 access-class 2 in transport input telnet ssh transport output none ! scheduler max-task-time 5000 ! end any ideas? :)

  Read the article

• Cisco 881 losing NAT NVI translation config after reload

  - by MasterRoot24

  This is a weird one, so I'll try to explain in as much detail as I can so I'm giving the whole picture. As I've mentioned in my other questions, I'm in the process of setting up a new Cisco 881 as my WAN router and NAT firewall. I'm facing an issue where NAT NVI rules that I have configured are not enabled after a reload of the router, regardless of the fact that they are present in the startup-config. In order to clarify this a little, here's the relevant section of my current running-config: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 ...and here's the mappings 'in action': Router1#show ip nat nvi translations | include --- tcp <WAN IP>:25 192.168.1.x:25 --- --- tcp <WAN IP>:80 192.168.1.x:80 --- --- tcp <WAN IP>:143 192.168.1.x:143 --- --- tcp <WAN IP>:443 192.168.1.x:443 --- --- tcp <WAN IP>:587 192.168.1.x:587 --- --- tcp <WAN IP>:993 192.168.1.x:993 --- --- tcp <WAN IP>:1723 192.168.1.x:1723 --- --- ...and here's proof that the mappings are saved to startup-config: Router1#show startup-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 However, look what happens after a reload of the router: Router1#reload Proceed with reload? [confirm]Connection to router closed by remote host. Connection to router closed. $ ssh joe@router Password: Authorized Access only Router1>en Password: Router1#show ip nat nvi translations | include --- Router1# Router1#show ip nat translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Here's proof that the running config should have the mappings setup as NVI: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 At this point, the mappings are not working (inbound connections from WAN on the HTTP/IMAP fail). I presume that this is because my interfaces are using ip nat enable for use with NVI mappings, instead of ip nat inside/outside. So, I re-apply the mappings: Router1#configure ter Router1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router1(config)#ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 Router1(config)#ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 Router1(config)#ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 Router1(config)#ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 Router1(config)#ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 Router1(config)#ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 Router1(config)#ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 Router1(config)#end ... then they show up correctly: Router1#show ip nat nvi translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Router1#show ip nat translations | include --- Router1# ... furthermore, now from both WAN and LAN, the services mapped above now work until the next reload. All of the above is required every time I have to reload the router (which is all too often at the moment :-( ). Here's my full current config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip access-group 101 in ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 access-list 101 permit udp 193.x.x.0 0.0.0.255 any eq 5060 access-list 101 deny udp any any eq 5060 access-list 101 permit ip any any ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end I'd appreciate it greatly if anyone can help me find out why these mappings are not setup correctly using the saved config after a reload.

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >