Search Results

Search found 1180 results on 48 pages for 'clock'.

Page 12/48 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • Can't connect to WIFI after sleep Ubuntu 14.04

    - by user3380404
    After an upgrade over a previous version to Ubuntu 14.04 I have problems with connecting to WiFi. After suspending it won't reconnect to any existing network unless I restart the laptop. sudo lshw -C network: *-network description: Ethernet interface product: 82567LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:27:13:b4:d3:58 capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.3.2-k firmware=1.8-3 latency=0 link=no multicast=yes port=twisted pair resources: irq:45 memory:fc200000-fc21ffff memory:fc225000-fc225fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:c6:6b:c8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-29-generic firmware=8.83.5.1 build 33692 ip=10.0.1.160 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:48 memory:f4200000-f4201fff

    Read the article

  • Could not apply stored configuration for monitors

    - by Hernantz
    Well this happened when I upgraded to Natty. Not only seems I can't change my resolution to higher than 1024x768 but it appears at the left and using only 70% of the monitor's width. I tried logging in but in ubuntu classic mode, and i was able to change it, but that trick did not work anymore. (May this be a compiz problem?) Anyways, here is my /var/log/Xorg.0.log http://pastebin.com/Ew4wwLab and lspci -nn | grep VGA: 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) I tried using xrandr for adding manually a resolution of 1280x1768 but without luck. Here is the xrandr output Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) TV1 disconnected (normal left inverted right x axis y axis) 1280x1024 (0xc6) 109.0MHz h: width 1280 start 1368 end 1496 total 1712 skew 0 clock 63.7KHz v: height 1024 start 1027 end 1034 total 1063 clock 59.9Hz

    Read the article

  • 64 bit Ubuntu sees half my RAM

    - by koehn
    This is on my AMD FX(tm)-4100 Quad-Core Processor (according to /proc/cpuinfo) on a machine with two 4GB RAM DIMMs. BIOS shows 8GB RAM installed. Any help would be appreciated. RAM: Extreme Performance Sector 5 G Series 8GB DDR3-1333 (PC3-1066) Enhanced Latency Dual Channel Desktop Memory Kit (Two 4GB Memory Modules) MB: GA-78LMT-S2P Socket AM3+ 760G mATX AMD Motherboard CPU: FX 4100 Black Edition 3.6GHz Quad-Core Socket AM3+ Boxed Processor Here's what the software says: $ free total used free shared buffers cached Mem: 3515100 3293656 221444 0 19260 2670352 -/+ buffers/cache: 604044 2911056 Swap: 3650556 90916 3559640 $ uname -a Linux mythbuntu 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux From lshw: *-memory description: System Memory physical id: 20 slot: System board or motherboard size: 4GiB *-bank:0 description: DIMM 1066 MHz (0.9 ns) product: None vendor: None physical id: 0 serial: None slot: A0 size: 2GiB width: 64 bits clock: 1066MHz (0.9ns) *-bank:1 description: DIMM 1066 MHz (0.9 ns) product: None vendor: None physical id: 1 serial: None slot: A1 size: 2GiB width: 64 bits clock: 1066MHz (0.9ns)

    Read the article

  • Wireless not working with an Atheros AR9285

    - by Neeraj
    I recently installed Ubuntu 12.04 and found my wireless card is not detected by OS. I tired to detect it by network manager but still it is not get output of the required command: toor@Linux:~$ sudo lshw -class network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:9e:22:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=124.123.227.84 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:f2400000-f243ffff ioport:2000(size=128) *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f2500000-f250ffff and toor@Linux:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no Please let me know what more info is required to resolve it.

    Read the article

  • C-states and P-states : confounding factors for benchmarking

    - by Dave
    I was recently looking into a performance issue in the java.util.concurrent (JUC) fork-join pool framework related to particularly long latencies when trying to wake (unpark) threads in the pool. Eventually I tracked the issue down to the power & scaling governor and idle-state policies on x86. Briefly, P-states refer to the set of clock rates (speeds) at which a processor can run. C-states reflect the possible idle states. The deeper the C-state (higher numerical values) the less power the processor will draw, but the longer it takes the processor to respond and exit that sleep state on the next idle to non-idle transition. In some cases the latency can be worse than 100 microseconds. C0 is normal execution state, and P0 is "full speed" with higher Pn values reflecting reduced clock rates. C-states are P-states are orthogonal, although P-states only have meaning at C0. You could also think of the states as occupying a spectrum as follows : P0, P1, P2, Pn, C1, C2, ... Cn, where all the P-states are at C0. Our fork-join framework was calling unpark() to wake a thread from the pool, and that thread was being dispatched onto a processor at deep C-state, so we were observing rather impressive latencies between the time of the unpark and the time the thread actually resumed and was able to accept work. (I originally thought we were seeing situations where the wakee was preempting the waker, but that wasn't the case. I'll save that topic for a future blog entry). It's also worth pointing out that higher P-state values draw less power and there's usually some latency in ramping up the clock (P-states) in response to offered load. The issue of C-states and P-states isn't new and has been described at length elsewhere, but it may be new to Java programmers, adding a new confounding factor to benchmarking methodologies and procedures. To get stable results I'd recommend running at C0 and P0, particularly for server-side applications. As appropriate, disabling "turbo" mode may also be prudent. But it also makes sense to run with the system defaults to understand if your application exhibits any performance sensitivity to power management policies. The operating system power management sub-system typically control the P-state and C-states based on current and recent load. The scaling governor manages P-states. Operating systems often use adaptive policies that try to avoid deep C-states for some period if recent deep idle episodes proved to be very short and futile. This helps make the system more responsive under bursty or otherwise irregular load. But it also means the system is stateful and exhibits a memory effect, which can further complicate benchmarking. Forcing C0 + P0 should avoid this issue.

    Read the article

  • Ask the Readers: The Two-Step Login Verification Process – Security Boost or Just Another Hassle?

    - by Asian Angel
    Google recently introduced a new optional two-step login verification process for Google accounts to help increase account security. What we would like to know this week is if you think this will really help improve account security, should be implemented by others in addition to Google, or would simply add a new layer of hassle to using your accounts Latest Features How-To Geek ETC How To Remove People and Objects From Photographs In Photoshop Ask How-To Geek: How Can I Monitor My Bandwidth Usage? Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Stop Believing TV’s Lies: The Real Truth About "Enhancing" Images The Legend of Zelda – 1980s High School Style [Video] Suspended Sentence is a Free Cross-Platform Point and Click Game Build a Batman-Style Hidden Bust Switch Make Your Clock Creates a Custom Clock for your Android Homescreen Download the Anime Angels Theme for Windows 7 CyanogenMod Updates; Rolls out Android 2.3 to the Less Fortunate

    Read the article

  • Symbol of VPNanytime is not shown anymore after upgrading from Ubuntu 11.04 to 11.10

    - by Aufwind
    Usually when I start VPN anytime (by calling a certain url in firefox) in Ubuntu 11.10 I saw a little "green symbol with a yellow lock in front of it" for the VPN anytime client near the clock. If I wanted to quit the VPN connection I just clicked on this symbol and hit logout/quit. Today I upgraded to Ubuntu 11.10 and the VPN connection works here fine too. But the symbol near the clock is not shown anymore. Is this a bug or do I have to set this up manually? And is there a way to quit the client perhaps by terminal? Currently I just do a restart, when I want the vpn connection terminated and that's kind uncomfortable. :-) Thanks for any suggestions!

    Read the article

  • Inspiron 5720 unclaimed hardware

    - by Chelios
    I have two unclaimed devices in my Dell Inspiron 5720: *-display UNCLAIMED description: 3D controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) *-serial UNCLAIMED description: SMBus product: 7 Series/C210 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 04 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1614000-f16140ff ioport:efa0(size=32) What are these devices and what drivers do I need for them? Thanks!

    Read the article

  • How to make Devilspie Make an Applet be "silent" but then openable

    - by Kendor
    Am using gnome-shell with 11.10. I have two panel based applets (Toggl and Gnome Alarm Clock) that I run at startup. The issue is that they start as Windows, and I'd like them to start "silently" but still be able to recall their interface when I need them. I installed Devilspie and gDevilspie which properly "close" the applets after starting them, but there's a "Catch 22." Because of the "close" behavior, they can never be opened again as long as the Devilspie daemon is running.. Is there a way around this? An example of the rule I'm using is this: ( if ( begin ( is ( application_name ) "alarm-clock-applet" ) ) ( begin ( close ) ( println "match" ) ) )

    Read the article

  • Which DB should I use for my newbie program?

    - by knijo
    I'm really new to programming, and I need some advice. I'm currently working on a very simple program to maintain a list of users at a company, as well as their clock in and clock out info. I would like to make this application easy to distribute (on a cd probably), and I'm looking for advice on which database to use for storing my data. My application is implemented using java and swing. A friend recommended MySQL, but I don't want to go installing the db server on every computer the application is installed on. Another friend recommended Access. Any tips would be greatly appreciated

    Read the article

  • Bomb timer adventure game win32 c++ [on hold]

    - by user3491746
    I'm working on an adventure game in win32 and opengl for my 2nd year university project for class. I am pretty much finished my game but I'm stuck on the concept of how to program a timer which outputs hh : mm : ss -- but which countdown, not up. I've made a clock which counts up using vector matrices and the segxseg matrix algorithm but I cannot figure out how to make a clock (it can be simple even text using wsprintf) that counts down in that format. Can anyone possible give me an example or some literature that I can read on how to do this? Please dont suggest for me to use another environment, I've already been working here for 2 months on this game, and I'm pretty much done so i'm at no point to switch over. Can anyone show me how I can take a shot at this component of my project? Thanks a bunch! Anything that I can get is appreciated.

    Read the article

  • How to Use Google Chrome as Your Default PDF Reader (the Easy Way)

    - by The Geek
    If you’re anything like 99% of everybody, you have some sort of PDF viewing software installed on your PC—but did you realize that you can use Google Chrome to view PDFs from your PC? It’s easy! We’re showing off how to do this in Windows, but theoretically it would work for OS X or Linux as well. If you’ve tried it, let us know in the comments Latest Features How-To Geek ETC How to Use Google Chrome as Your Default PDF Reader (the Easy Way) How To Remove People and Objects From Photographs In Photoshop Ask How-To Geek: How Can I Monitor My Bandwidth Usage? Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Final Man vs. Machine Round of Jeopardy Unfolds; Watson Dominates The Legend of Zelda – 1980s High School Style [Video] Suspended Sentence is a Free Cross-Platform Point and Click Game Build a Batman-Style Hidden Bust Switch Make Your Clock Creates a Custom Clock for your Android Homescreen Download the Anime Angels Theme for Windows 7

    Read the article

  • Why is the superblock last mount time in the future?

    - by user69541
    Future time: Since installing Ubuntu 12.04, I regularly have to fun fsck and reset my clock because it shows a 'future time' : Err.Msg. "superblock last mount time is in the future by less than a day, probably due to hardware clock being incorrectly set." FIXED. According to what I have read, it looks like I'm in the right place to get an answer. Following are my feeble attempts to rectify this annoyance: mjh@mjh-desktop:~$ sudo service ntp start [sudo] password for mjh: ntp: unrecognized service mjh@mjh-desktop:~$ mjh@mjh-desktop:~$ sudo apt-get install update Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package update mjh@mjh-desktop:~$ sudo service ntp start ntp: unrecognized service mjh@mjh-desktop:~$ Suggestions? Matthew

    Read the article

  • HW resources for the device driver [closed]

    - by VladimirLenin
    Need to provide memory and IRQ resources to the Linux kernel in order to bring up the CAN controller. Have no idea how to get them. Below is the structure I need to fill in. This structure I have taken for example, this is for the Run-Time Clock, but I need for CAN controller. Both are on the same board, and there are constants for RT Clock (and all other devices), but not for my CAN chip. When looking at the subject chip driver's code (sp_probe() function), I see it needs the same type resources. struct resource tegra_rtc_resources[] = { [0] = { .start = ???, .end = ???, .flags = IORESOURCE_MEM, }, [1] = { .start = ???, .end = ???, .flags = IORESOURCE_IRQ, }, };

    Read the article

  • Distorted choppy audio in Precise

    - by Misery
    After installing Precise on my PC, some problems with soud occure. While using Lucid there were no problems. The sound is choppy and distorted in low tones range. As I absolutely have no experience in setting/testing and doing anything with Audo Devices I need help even to diagnose the problem. update: sudo lshw -c multimedia *-multimedia description: Audio device product: Radeon X1200 Series Audio Controller vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 5.2 bus info: pci@0000:01:05.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=snd_hda_intel latency=32 resources: irq:19 memory:fdafc000-fdafffff *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=snd_hda_intel latency=32 resources: irq:16 memory:fe024000-fe027fff update 2: It has something to do with the volume. If the audio is quiet it is not choppy, if the sound is loud then it begins to be choppy. Regards, Misery

    Read the article

  • What is the point in using real time?

    - by bobobobo
    I understand that using real time frame elapses (which should vary between 16-17ms on average) are provided by a lot of frameworks. GetTimeElapsedSinceLastFrame, and it gives you the wall clock time. But should we use this information in basic physics simulation? It looks to me to be a bad idea. Say there is a slight lag on the machine, for whatever reason (say a virus scanner starts up). The calculations all jump, and there is no need for this. Why not use a virtual second and ignore wall clock time? For gameplay on the level of Commander Keen, shouldn't you always use the virtual second and not real-time? (Besides stopwatch timing for race games) I don't see a need to use real time and not a fixed 16ms time step.

    Read the article

  • How to synchronize the ball in a network pong game?

    - by Thaars
    I’m developing a multiplayer network pong game, my first game ever. The current state is, I’ve running the physic engine with the same configurations on the server and the clients. The own paddle movement is predicted and get just confirmed by the authoritative server. Is a difference detected between them, I correct the position at the client by interpolation. The opponent paddle is also interpolated 200ms to 100ms in the past, because the server is broadcasting snapshots every 100ms to each client. So far it works very well, but now I have to simulate the ball and have a problem to understanding the procedure. I’ve read Valve’s (and many other) articles about fast-paced multiplayer several times and understood their approach. Maybe I can compare my ball with their bullets, but their advantage is, the bullets are not visible. When I have to display the ball, and see my paddle in the present, the opponent in the past and the server is somewhere between it, how can I synchronize the ball over all instances and ensure, that it got ever hit by the paddle even if the paddle is fast moving? Currently my ball’s position is simply set by a server update, so it can happen, that the ball bounces back, even if the paddle is some pixel away (because of a delayed server position). Until now I’ve got no synced clock over all instances. I’m sending a client step index with each update to the server. If the server did his job, he sends the snapshot with the last step index of each client back to the clients. Now I’m looking for the stored position at the returned step index and compare them. Do I need a common clock to sync the ball? EDIT: I've tried to sync a common clock for the server and all clients with a timestamp. But I think it's better to use an own stepping instead of a timestamp (so I don't need to calculate with the ping and so on - and the timestamp will never be exact). The physics are running 60 times per second and now I use this for keeping them synchronized. Is that a good way? When the ball gets calculated by each client, the angle after bouncing can differ because of the different position of the paddles (the opponent is 200ms in the past). When the server is sending his ball position, velocity and angle (because he knows the position of each paddle and is authoritative), the ball could be in a very different position because of the different angles after bouncing (because the clients receive the server data after 100ms). How is it possible to interpolate such a huge difference? I posted this question some days ago at stackoverflow, but got no answer yet. Maybe this is the better place for this question.

    Read the article

  • Check if the vector is behind another or maybe opposite directions?

    - by Gilson
    I'm doing a network game and on the client side, i interpolate the client position with the server sent extrapolated position. The client has its own physics simulation wich is corrected by the server in steps. The problem is when it laggs and i 'kick' the ball, the server gets a delayed message and sends me the position backwards of the client position wich makes the ball goes back and forth. I want to ignore those and maybe compensate that on the server, not sure though. The problem is the clock difference on those case are 0.07ms or 0.10 ms wich isn't that high to ignore the message i guess. When i get the server position, i extrapolate with the clock interval * serverBallVelocity Can i check if my new ball server position is behind my actual ball vector position? I tried to use the dot product after normalized the two vectors to check if they are opposite but it ain't working properly. Any suggestions on checking that?

    Read the article

  • disable intel gpu in ubuntu 12.04

    - by small_potato
    I am wondering if there is anything to disable the intel gpu on ubuntu 12.04. I want to be able to setup dual monitor using nvidia-settings. It seems the intel gpu is used for display as suggested by sudo lshw -c display the output is *-display description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:c0000000-c0ffffff memory:90000000-9fffffff memory:a0000000-a1ffffff ioport:4000(size=128) memory:a2000000-a207ffff *-display description: VGA compatible controller product: Haswell Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:c2000000-c23fffff memory:b0000000-bfffffff ioport:5000(size=64) I have a lenovoY410 with GT750M. It seems there is no way to turn off the intel gpu in bios either. Help please. Thanks.

    Read the article

  • Html 5 &ndash; new size units

    - by Norgean
    There are some new size units with CSS 3, which allows you to resize elements relative to the viewport size. They are vw, vh, vmin (that’s vm in IE), and perhaps vmax. (Viewport width, height, smaller of the two, larger of the two.) 8vw is 8% of the viewport width – or 205 pixels on my 2560 screen. I created a tiny demo clock which sizes the elements so that it uses the whole screen. Clock – in Norwegian, but it’s the source that is interesting… Bug: Resize does not work. Tested for IE 9 & 10 and Chrome. Firefox and Safari: does not work.

    Read the article

  • Service with intents not working. Help needed

    - by tristan202
    I need help in making my click intents work. I used to have them in my appwidgetprovider, but decided to move them into a service, but I am having trouble getting it to work. Below is the entire code from my intentservice: public class IntentService extends Service { static final String ACTION_UPDATE = "android.tristan.widget.digiclock.action.UPDATE_2"; private final static IntentFilter sIntentFilter; public int layoutID = R.layout.clock; int appWidgetIds = 0; static { sIntentFilter = new IntentFilter(); } @Override public IBinder onBind(Intent intent) { return null; } @Override public void onStart(Intent intent, int startId) { super.onStart(intent, startId); } @Override public void onCreate() { super.onCreate(); registerReceiver(onClickTop, sIntentFilter); registerReceiver(onClickBottom, sIntentFilter); Log.d("DigiClock IntentService", "IntentService Started."); } @Override public void onDestroy() { super.onDestroy(); unregisterReceiver(onClickTop); unregisterReceiver(onClickBottom); } private final BroadcastReceiver onClickTop = new BroadcastReceiver() { @Override public void onReceive(Context context, Intent intent) { if(intent.getAction().equals("android.tristan.widget.digiclock.CLICK")) { PackageManager packageManager = context.getPackageManager(); Intent alarmClockIntent = new Intent(Intent.ACTION_MAIN).addCategory(Intent.CATEGORY_LAUNCHER); String clockImpls[][] = { {"HTC Alarm Clock", "com.htc.android.worldclock", "com.htc.android.worldclock.WorldClockTabControl" }, {"Standar Alarm Clock", "com.android.deskclock", "com.android.deskclock.AlarmClock"}, {"Froyo Nexus Alarm Clock", "com.google.android.deskclock", "com.android.deskclock.DeskClock"}, {"Moto Blur Alarm Clock", "com.motorola.blur.alarmclock", "com.motorola.blur.alarmclock.AlarmClock"} }; boolean foundClockImpl = false; for(int i=0; i<clockImpls.length; i++) { String vendor = clockImpls[i][0]; String packageName = clockImpls[i][1]; String className = clockImpls[i][2]; try { ComponentName cn = new ComponentName(packageName, className); ActivityInfo aInfo = packageManager.getActivityInfo(cn, PackageManager.GET_META_DATA); alarmClockIntent.setComponent(cn); foundClockImpl = true; } catch (NameNotFoundException e) { Log.d("Error, ", vendor + " does not exist"); } } if (foundClockImpl) { Vibrator vibrator = (Vibrator) context.getSystemService(Context.VIBRATOR_SERVICE); vibrator.vibrate(50); final RemoteViews views = new RemoteViews(context.getPackageName(), layoutID); views.setOnClickPendingIntent(R.id.TopRow, PendingIntent.getActivity(context, 0, new Intent(context, DigiClock.class).setFlags(Intent.FLAG_ACTIVITY_NEW_TASK), PendingIntent.FLAG_UPDATE_CURRENT)); AppWidgetManager.getInstance(context).updateAppWidget(intent.getIntArrayExtra(AppWidgetManager.EXTRA_APPWIDGET_IDS), views); alarmClockIntent.setFlags(Intent.FLAG_ACTIVITY_NEW_TASK); context.startActivity(alarmClockIntent); } } } }; private final BroadcastReceiver onClickBottom = new BroadcastReceiver() { @Override public void onReceive(Context context, Intent intent) { if(intent.getAction().equals("android.tristan.widget.digiclock.CLICK_2")) { PackageManager calendarManager = context.getPackageManager(); Intent calendarIntent = new Intent(Intent.ACTION_MAIN).addCategory(Intent.CATEGORY_LAUNCHER); String calendarImpls[][] = { {"HTC Calendar", "com.htc.calendar", "com.htc.calendar.LaunchActivity" }, {"Standard Calendar", "com.android.calendar", "com.android.calendar.LaunchActivity"}, {"Moto Blur Calendar", "com.motorola.blur.calendar", "com.motorola.blur.calendar.LaunchActivity"} }; boolean foundCalendarImpl = false; for(int i=0; i<calendarImpls.length; i++) { String vendor = calendarImpls[i][0]; String packageName = calendarImpls[i][1]; String className = calendarImpls[i][2]; try { ComponentName cn = new ComponentName(packageName, className); ActivityInfo aInfo = calendarManager.getActivityInfo(cn, PackageManager.GET_META_DATA); calendarIntent.setComponent(cn); foundCalendarImpl = true; } catch (NameNotFoundException e) { Log.d("Error, ", vendor + " does not exist"); } } if (foundCalendarImpl) { Vibrator vibrator = (Vibrator) context.getSystemService(Context.VIBRATOR_SERVICE); vibrator.vibrate(50); final RemoteViews views2 = new RemoteViews(context.getPackageName(), layoutID); views2.setOnClickPendingIntent(R.id.BottomRow, PendingIntent.getActivity(context, 0, new Intent(context, DigiClock.class).setFlags(Intent.FLAG_ACTIVITY_NEW_TASK), PendingIntent.FLAG_UPDATE_CURRENT)); AppWidgetManager.getInstance(context).updateAppWidget(intent.getIntArrayExtra(AppWidgetManager.EXTRA_APPWIDGET_IDS), views2); calendarIntent.setFlags(Intent.FLAG_ACTIVITY_NEW_TASK); context.startActivity(calendarIntent); } } }; }; ;}; What am I doing wrong here?

    Read the article

  • which grabber is good enough to get 1000fps?

    - by user261002
    I have two framegrabber with a fast camera (1800+ fps). can anybody who understand the hardware, explain to me which of the following grabbers can help me more to grab 1000fps ? here are the the features of the two grabbers : Inspecta-5 Full Camera Link® Version: · Support for line scan and area cameras. · Video data rate of up to 660 Mbytes/sec. · PCI – X bus interface for 64 Bit data width and 66 MHz clock frequency. · PCI bus interface for 32 Bit data width and 33 MHz clock frequency. · 2 Gigabyte Onboard Memory for fast video streams. · Four opt coupled input- output ports for external trigger and encoder signals. · 528 Mbytes/sec. maximum data rate on the PCI–X Bus. · SDK for Windows 2000/XP SILICONSOFTWARE V-Series Camera Link : “microEnable IV VD4-CL” · Camera Pixel Clock Support 85 MHz · Area Scan Cameras 32k * 64k max. image size · Line Scan Cameras 64k max. image width · Acquisition Buffer: 512 MB DDR-RAM · Sustainable Transfer Rate (max.) 850 MBytes/sec. · microEnable SDK for Windows XP/Vista/ 7/ Linux

    Read the article

  • Project Euler #290 in python, hint please

    - by debragail
    This solution is grossly inefficient. What am I missing? #!/usr/bin/env python #coding: utf-8 import time from timestrings import * start = time.clock() maxpower = 18 count = 0 for i in range(0, 10 ** maxpower - 1): if i % 9 == 0: result1 = list(str(i)) result2 = list(str(137 * i)) sum1 = 0 for j in result1: sum1 += int(j) sum2 = 0 for j in result2: sum2 += int(j) if sum1 == sum2: print (i, sum1) count += 1 finish = time.clock() print ("Project Euler, Project 290") print () print ("Answer:", count) print ("Time:", stringifytime(finish - start))

    Read the article

  • g++ SSE intrinsics dilemma - value from intrinsic "saturates"

    - by Sriram
    Hi, I wrote a simple program to implement SSE intrinsics for computing the inner product of two large (100000 or more elements) vectors. The program compares the execution time for both, inner product computed the conventional way and using intrinsics. Everything works out fine, until I insert (just for the fun of it) an inner loop before the statement that computes the inner product. Before I go further, here is the code: //this is a sample Intrinsics program to compute inner product of two vectors and compare Intrinsics with traditional method of doing things. #include <iostream> #include <iomanip> #include <xmmintrin.h> #include <stdio.h> #include <time.h> #include <stdlib.h> using namespace std; typedef float v4sf __attribute__ ((vector_size(16))); double innerProduct(float* arr1, int len1, float* arr2, int len2) { //assume len1 = len2. float result = 0.0; for(int i = 0; i < len1; i++) { for(int j = 0; j < len1; j++) { result += (arr1[i] * arr2[i]); } } //float y = 1.23e+09; //cout << "y = " << y << endl; return result; } double sse_v4sf_innerProduct(float* arr1, int len1, float* arr2, int len2) { //assume that len1 = len2. if(len1 != len2) { cout << "Lengths not equal." << endl; exit(1); } /*steps: * 1. load a long-type (4 float) into a v4sf type data from both arrays. * 2. multiply the two. * 3. multiply the same and store result. * 4. add this to previous results. */ v4sf arr1Data, arr2Data, prevSums, multVal, xyz; //__builtin_ia32_xorps(prevSums, prevSums); //making it equal zero. //can explicitly load 0 into prevSums using loadps or storeps (Check). float temp[4] = {0.0, 0.0, 0.0, 0.0}; prevSums = __builtin_ia32_loadups(temp); float result = 0.0; for(int i = 0; i < (len1 - 3); i += 4) { for(int j = 0; j < len1; j++) { arr1Data = __builtin_ia32_loadups(&arr1[i]); arr2Data = __builtin_ia32_loadups(&arr2[i]); //store the contents of two arrays. multVal = __builtin_ia32_mulps(arr1Data, arr2Data); //multiply. xyz = __builtin_ia32_addps(multVal, prevSums); prevSums = xyz; } } //prevSums will hold the sums of 4 32-bit floating point values taken at a time. Individual entries in prevSums also need to be added. __builtin_ia32_storeups(temp, prevSums); //store prevSums into temp. cout << "Values of temp:" << endl; for(int i = 0; i < 4; i++) cout << temp[i] << endl; result += temp[0] + temp[1] + temp[2] + temp[3]; return result; } int main() { clock_t begin, end; int length = 100000; float *arr1, *arr2; double result_Conventional, result_Intrinsic; // printStats("Allocating memory."); arr1 = new float[length]; arr2 = new float[length]; // printStats("End allocation."); srand(time(NULL)); //init random seed. // printStats("Initializing array1 and array2"); begin = clock(); for(int i = 0; i < length; i++) { // for(int j = 0; j < length; j++) { // arr1[i] = rand() % 10 + 1; arr1[i] = 2.5; // arr2[i] = rand() % 10 - 1; arr2[i] = 2.5; // } } end = clock(); cout << "Time to initialize array1 and array2 = " << ((double) (end - begin)) / CLOCKS_PER_SEC << endl; // printStats("Finished initialization."); // printStats("Begin inner product conventionally."); begin = clock(); result_Conventional = innerProduct(arr1, length, arr2, length); end = clock(); cout << "Time to compute inner product conventionally = " << ((double) (end - begin)) / CLOCKS_PER_SEC << endl; // printStats("End inner product conventionally."); // printStats("Begin inner product using Intrinsics."); begin = clock(); result_Intrinsic = sse_v4sf_innerProduct(arr1, length, arr2, length); end = clock(); cout << "Time to compute inner product with intrinsics = " << ((double) (end - begin)) / CLOCKS_PER_SEC << endl; //printStats("End inner product using Intrinsics."); cout << "Results: " << endl; cout << " result_Conventional = " << result_Conventional << endl; cout << " result_Intrinsics = " << result_Intrinsic << endl; return 0; } I use the following g++ invocation to build this: g++ -W -Wall -O2 -pedantic -march=i386 -msse intrinsics_SSE_innerProduct.C -o innerProduct Each of the loops above, in both the functions, runs a total of N^2 times. However, given that arr1 and arr2 (the two floating point vectors) are loaded with a value 2.5, the length of the array is 100,000, the result in both cases should be 6.25e+10. The results I get are: Results: result_Conventional = 6.25e+10 result_Intrinsics = 5.36871e+08 This is not all. It seems that the value returned from the function that uses intrinsics "saturates" at the value above. I tried putting other values for the elements of the array and different sizes too. But it seems that any value above 1.0 for the array contents and any size above 1000 meets with the same value we see above. Initially, I thought it might be because all operations within SSE are in floating point, but floating point should be able to store a number that is of the order of e+08. I am trying to see where I could be going wrong but cannot seem to figure it out. I am using g++ version: g++ (GCC) 4.4.1 20090725 (Red Hat 4.4.1-2). Any help on this is most welcome. Thanks, Sriram.

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >