Search Results

Search found 2692 results on 108 pages for 'ts gateway'.

Page 12/108 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • Fortigate Remote VPN : no matching gateway for new request

    - by Kedare
    I am trying to configure a Fortigate 60C to act as an IPSec endpoint for remote VPN. I configured it like this : SCR-F0-FGT100C-1 # diagnose vpn ike config vd: root/0 name: SCR-REMOTEVPN serial: 7 version: 1 type: dynamic mode: aggressive dpd: enable retry-count 3 interval 5000ms auth: psk dhgrp: 2 xauth: server-auto xauth-group: VPN-group interface: wan1 distance: 1 priority: 0 phase2s: SCR-REMOTEVPN-PH2 proto 0 src 0.0.0.0/0.0.0.0:0 dst 0.0.0.0/0.0.0.0:0 dhgrp 5 replay keep-alive dhcp policies: none Here is the configuration: config vpn ipsec phase1-interface edit "SCR-REMOTEVPN" set type dynamic set interface "wan1" set dhgrp 2 set xauthtype auto set mode aggressive set proposal aes256-sha1 aes256-md5 set authusrgrp "VPN-group" set psksecret ENC xxx next config vpn ipsec phase2-interface edit "SCR-REMOTEVPN-PH2" set keepalive enable set phase1name "SCR-REMOTEVPN" set proposal aes256-sha1 aes256-md5 set dhcp-ipsec enable next end But when I try to connect from a remote device (I tested with an Android Phone), the phone fail to connect and the fortinet return this error : 2012-07-20 13:08:51 log_id=0101037124 type=event subtype=ipsec pri=error vd="root" msg="IPsec phase 1 error" action="negotiate" rem_ip=xxx loc_ip=xxx rem_port=1049 loc_port=500 out_intf="wan1" cookies="xxx" user="N/A" group="N/A" xauth_user="N/A" xauth_group="N/A" vpn_tunnel="N/A" status=negotiate_error error_reason=no matching gateway for new request peer_notif=INITIAL-CONTACT I tried searching on the web, but i did not find anything revelant to this. Do you have any idea of what can be the problem ? I tried many combinaisons of settings on the fortigate without success..

    Read the article

  • Routing static IP traffic on a Comcast Business Class IP Gateway (SMCD3G-CCR)

    - by Jakobud
    We are in the process of replacing our firewall, which is currently the only thing connected to our Comcast Business Class modem. Comcast gives us 5 static IP addresses. Currently, all traffic to all 5 static IPs goes directly to the existing firewall. Eventually, obviously all traffic will goto the new firewall, once the old firewall is removed from the network. But in the meantime, as we will have two firewalls plugged into the same Comcast modem, I need to route certain traffic to the new firewall instead of the old one. The firewall switchover is going to be slow and gradual as I am testing it, so I can't simply unplug the existing firewall and plug in the new one. So my question is, how do I tell the modem to route all traffic that goes to a specific IP to goto the new firewall instead of the old one? I've logged into the web interface for the modem, but the available options aren't very clear. There is a 1-to-1 NAT option (which I can't seem to get the interface for it to work properly) but I also see a "Static Routing" section. I always understood Static Routing to refer to routing data within the LAN though, so I'm not sure if that's what I'm looking for or not. Keep in mind, I'm not looking to do simple port forwarding. I'm wanting 100% of traffic to certain public static IPs to go to the specified connected firewall (I'll deal with service policies there). The modem is an SMC SMCD3G-CCR and is labeled as a Comcast Business Class Business IP Gateway. Any help or direction would be greatly appreciated.

    Read the article

  • Route return traffic to correct gateway depending on service

    - by Marnix van Valen
    On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

    Read the article

  • Nginx 502 Bad Gateway: It just won't stop

    - by David
    I have the same problem that most people seem to have with Nginx: 502 bad gateway errors. They are intermittent but typically happen more than once per session, which means my users are probably running into it nearly every time they use the app. I've tried adjusting fastcgi_buffers and fastcgi_buffer_size (in both directions) to no avail. I've tried various other things with the configuration file but nothing seems to work. Here's my config (note that I've stripped away most of the things I've tried, since they didn't work and I didn't want to bloat the file with a bunch of un-related directives): server { root /usr/share/nginx/www/; index index.php; # Make site accessible from http://localhost/ server_name localhost; # Pass PHP scripts to PHP-FPM location ~ \.php { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; } # Lock the site location / { auth_basic "Administrator Login"; auth_basic_user_file /usr/share/nginx/.htpasswd; } # Hide the password file location ~ /\. { deny all; } client_max_body_size 8M; } I'm running a small Rackspace cloud server, which should be plenty for handling an app with a small user base...

    Read the article

  • RD Gateway reporting features/capabilities

    - by Don
    We have just implemented RD Gateway for our own department in preparation for a push to the whole agency for telecommuting. It is all setup and working great, but I was trying to figure out how best to go about monitoring/reporting of users. I see third party software out there that will do it, but is there anything built-in or via powershell/scripting that I could use that would give me a report of the daily activity of users? Something to say, "User A connected at this time, was on for this long, sent/received this much data"? Basically some of the same stuff you can see in event viewer. Ideally I'd like to be able to have this setup so that once a day it emails me with the daily usage for when a supervisor asks about if their person is actually working (or at least online sending and receiving x amount of data), I'll have some metrics to give them. I realize that actual work output is relevant and more of a managerial issue, but I would like to be able to offer as much as I can from my end when asked. Thoughts? Thanks!

    Read the article

  • Win/Bios showing wrong RAM in Gateway Netbook?

    - by Ael
    I've seen similar problems, but this seems slightly unique, maybe... I have a Gateway LT21 netbook, Win7. I've upgraded RAM from 1gb to 2gb. It didn't work. So I updated to the latest Bios 1.25, then it worked. 2gb was recognized in the Bios and in Windows. Every was fine. Now today it seemed slow and, to my surprise, both the Bios and Win show only 1gb. :/ I've run memory diagnostic, no error. I entered bios and hit Exit and Save. Still 1gb. I took out the ram, put it back. Still 1gb. :/ CPU-Z shows 2048mb/2gb of RAM. Further testing: if i put in the old 1gb ram, turn on, then put in the new 2gb ram again, the Bios and Win show 2gb of ram. BUT, once restarted at all (even from Bios) it seems to go back to showing incorrect 1gb ram again. :// (There are very few options in the bios, none appear memory-related.) Any ideas?

    Read the article

  • One Windows Domain workstation can ping gateway but gets no internet access

    - by dindeman
    One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

    Read the article

  • OpenVPN Clients using server's connection (with no default gateway)

    - by Branden Martin
    I wanted an OpenVPN server so that I could create a private VPN network for staff to connect to the server. However, not as planned, when clients connect to the VPN, it's using the VPN's internet connection (ex: when going to whatsmyip.com, it's that of the server and not the clients home connection). server.conf local <serverip> port 1194 proto udp dev tun ca ca.crt cert x.crt key x.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 9 client.conf client dev tun proto udp remote <srever> 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert x.crt key x.key ns-cert-type server comp-lzo verb 3 Server's route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 69.64.48.0 * 255.255.252.0 U 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 Server's IP Tables Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-proftpd tcp -- anywhere anywhere multiport dports ftp,ftp-data,ftps,ftps-data fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-proftpd (1 references) target prot opt source destination RETURN all -- anywhere anywhere Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- anywhere anywhere My goal is that clients can only talk to the server and other clients that are connected. Hope I made sense. Thanks for the help!

    Read the article

  • phpMyAdmin causes php-fpm worker to restart (502 Bad Gateway)

    - by rndbit
    I am trying to set up a test site for myself. Everything works fine except phpMyAdmin. php installation loads my test site scripts, they work fine, however trying to load phpMyAdmin i get 502 Bad Gateway error. Judging from logs (that are not too helpful) it seems that php-fpm worker is crashing each time phpmyadmin is being accessed. No clue how or why.. Does anyone have any idea? nginx log: *3 recv() failed (104: Connection reset by peer) while reading response header from upstream, And php-fpm log: [07-Jun-2012 14:19:51] WARNING: [pool www] child 32179 exited on signal 11 (SIGSEGV) after 3.217902 seconds from start [07-Jun-2012 14:19:51] NOTICE: [pool www] child 32351 started My nginx conf: user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; fastcgi_buffers 8 16k; fastcgi_buffer_size 32k; include /etc/nginx/conf.d/*.conf; server { listen 443 ssl; listen 80; server_name testsite.net www.testsite.net; ssl on; ssl_certificate /var/www/html/admin/ssl/certificate.pem; ssl_certificate_key /var/www/html/admin/ssl/privatekey.pem; ssl_session_timeout 1m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5:!kEDH; ssl_prefer_server_ciphers on; access_log off; location ~ \.php$ { root /var/www/html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include /etc/nginx/fastcgi_params; } location / { root /var/www/html; index index.php; } } } php.ini is standard, with cgi.fix_pathinfo=0 php-fpm.conf: include=/etc/php-fpm.d/*.conf [global] pid = /var/run/php-fpm/php-fpm.pid error_log = /var/log/php-fpm/error.log log_level = notice php-fpm.d/www.conf: [www] listen = 127.0.0.1:9000 listen.allowed_clients = 127.0.0.1 user = nginx group = nginx pm = dynamic pm.max_children = 10 pm.start_servers = 1 pm.min_spare_servers = 1 pm.max_spare_servers = 10 slowlog = /var/log/php-fpm/www-slow.log php_flag[display_errors] = on php_admin_value[error_log] = /var/log/php-fpm/www-error.log php_admin_flag[log_errors] = on

    Read the article

  • 502 Bad Gateway with nginx + apache + subversion + ssl (SVN COPY)

    - by theplatz
    I've asked this on stackoverflow, but it may be better suited for serverfault... I'm having a problem running Apache + Subversion with SSL behind an Nginx proxy and I'm hoping someone might have the answer. I've scoured google for hours looking for the answer to my problem and can't seem to figure it out. What I'm seeing are "502 (Bad Gateway)" errors when trying to MOVE or COPY using subversion; however, checkouts and commits work fine. Here are the relevant parts (I think) of the nginx and apache config files in question: Nginx upstream subversion_hosts { server 127.0.0.1:80; } server { listen x.x.x.x:80; server_name hostname; access_log /srv/log/nginx/http.access_log main; error_log /srv/log/nginx/http.error_log info; # redirect all requests to https rewrite ^/(.*)$ https://hostname/$1 redirect; } # HTTPS server server { listen x.x.x.x:443; server_name hostname; passenger_enabled on; root /path/to/rails/root; access_log /srv/log/nginx/ssl.access_log main; error_log /srv/log/nginx/ssl.error_log info; ssl on; ssl_certificate server.crt; ssl_certificate_key server.key; add_header Front-End-Https on; location /svn { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; set $fixed_destination $http_destination; if ( $http_destination ~* ^https(.*)$ ) { set $fixed_destination http$1; } proxy_set_header Destination $fixed_destination; proxy_pass http://subversion_hosts; } } Apache Listen 127.0.0.1:80 <VirtualHost *:80> # in order to support COPY and MOVE, etc - over https (443), # ServerName _must_ be the same as the nginx servername # http://trac.edgewall.org/wiki/TracNginxRecipe ServerName hostname UseCanonicalName on <Location /svn> DAV svn SVNParentPath "/srv/svn" Order deny,allow Deny from all Satisfy any # Some config omitted ... </Location> ErrorLog /var/log/apache2/subversion_error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/subversion_access.log combined </VirtualHost> From what I could tell while researching this problem, the server name has to match on both the apache server as well as the nginx server, which I've done. Additionally, this problem seems to stick around even if I change the configuration to use http only.

    Read the article

  • php-fpm or nginx: bad gateway

    - by John Tate
    I'm getting a bad gateway error all the sudden for a site. I didn't change the configuration for the site, I just added a new server config where I put them under /etc/nginx/servers and it stopped working. The new server works, and there is no conflict between the php-fpm listen addresses. server { listen 80; server_name obfuscated.onion; location = / { root /var/www/sites/obfuse; index index.php; } location / { root /var/www/sites/obfuse; index index.php; if (!-f $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } if (!-d $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } } error_page 404 /index.php; location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { root /var/www/sites/obfuse; access_log off; expires 30d; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/sites/obfuse$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param PATH_INFO $fastcgi_script_name; include fastcgi_params; } } There is nothing unusual in php-fpm's log even when I raised the level to debug. [24-Jun-2013 09:10:37.357943] DEBUG: pid 6756, fpm_scoreboard_init_main(), line 40: got clock tick '100' [24-Jun-2013 09:10:37.358950] DEBUG: pid 6756, fpm_event_init_main(), line 333: event module is kqueue and 1 fds have been reserved [24-Jun-2013 09:10:37.358978] NOTICE: pid 6756, fpm_init(), line 83: fpm is running, pid 6756 [24-Jun-2013 09:10:37.359009] DEBUG: pid 6756, main(), line 1832: Sending "1" (OK) to parent via fd=5 [24-Jun-2013 09:10:37.389215] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 22288 started [24-Jun-2013 09:10:37.391343] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 21911 started [24-Jun-2013 09:10:37.391914] DEBUG: pid 6756, fpm_event_loop(), line 362: 5776 bytes have been reserved in SHM [24-Jun-2013 09:10:37.391941] NOTICE: pid 6756, fpm_event_loop(), line 363: ready to handle connections [24-Jun-2013 09:10:38.393048] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:39.403032] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:40.413070] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 I don't know why this has started happening, but the logs are not telling me anything. Please ask for more information than this, you'll probably need it.

    Read the article

  • Optimize "not in" query

    - by Vasu
    Please help optimize this query: SELECT ts.SiteId, COUNT(ts.SiteId) AS Count FROM ts WHERE ts.SiteId not in (SELECT ts.SiteId FROM ts WHERE ts.uniqueid = 'xxx') GROUP BY ts.SiteId ORDER BY Count DESC

    Read the article

  • Nginx + Nagios : 502 Bad gateway

    - by MrROY
    I have a fully new install nagios, but I can't access to it. Here's my Nginx config: server{ listen 80; server_name 61.148.45.10; # blahblah # Nagios Monitoring location /nagios3/ { proxy_pass http://127.0.0.1:80; } } Nagios is installed step by step(From this Linode guide): sudo apt-get install -y nagios3 Then I try to visit http://ip-address/nagios3/, but it shows 502 bad gateway. How do I deal with this ? This is my /var/log/syslog: Oct 25 14:18:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;1;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:19:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;1;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:19:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;2;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:20:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;2;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:20:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;3;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;3;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:21:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;HARD;4;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server nagios3: SERVICE NOTIFICATION: root;localhost;Disk Space;WARNING;notify-service-by-email;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server postfix/pickup[24474]: 4F89F394034C: uid=109 from=<nagios> Oct 25 14:21:17 my-server postfix/cleanup[27756]: 4F89F394034C: message-id=<20131025062117.4F89F394034C@my-server> Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: from=<nagios@[email protected]>, size=594, nrcpt=1 (queue active) Oct 25 14:21:17 my-server postfix/local[27758]: 4F89F394034C: to=<root@localhost>, relay=local, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: removed Oct 25 14:22:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;HARD;4;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server nagios3: SERVICE NOTIFICATION: root;localhost;HTTP;WARNING;notify-service-by-email;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server postfix/pickup[24474]: 219CA3940381: uid=109 from=<nagios> Oct 25 14:22:07 my-server postfix/cleanup[27756]: 219CA3940381: message-id=<20131025062207.219CA3940381@my-server> Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: from=<nagios@[email protected]>, size=605, nrcpt=1 (queue active) Oct 25 14:22:07 my-server postfix/local[27758]: 219CA3940381: to=<root@localhost>, relay=local, delay=0.12, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: removed Oct 25 14:39:01 my-server CRON[28242]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) And there're lot of 127.0.0.1 visit in nginx log, but I actually visit from a external ip: 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36"

    Read the article

  • 502 Bad Gateway - nginx

    - by ADH2
    I am randomly receiving 502 Bad Gateway error pages - I can reproduce this issue by modifying hosting plans in plesk 11 and in the same time refreshing a page for a minute or two. When I get the 502 error page all I have to do is refresh the browser and the page refreshes properly. i am using centos 6 this it from todays log (/var/log/nginx/error.log): 2012/12/04 10:52:07 [error] 21272#0: *545 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: 82.77.68.111, server: likeit-craiova.ro, request: "GET / HTTP/1.1", upstream: "http://195.254.135.113:7080/", host: "likeit-craiova.ro" this is the nginx config (/etc/nginx/nginx.conf) #user nginx; worker_processes 1; #error_log /var/log/nginx/error.log; #error_log /var/log/nginx/error.log notice; #error_log /var/log/nginx/error.log info; #pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; proxy_buffer_size 128k; proxy_buffers 4 256k; proxy_busy_buffers_size 256k; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #tcp_nodelay on; #gzip on; #gzip_disable "MSIE [1-6]\.(?!.*SV1)"; server_tokens off; include /etc/nginx/conf.d/*.conf; } fastcgi config file (/etc/nginx/fastcgi.conf): fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; fastcgi parameters config (/etc/nginx/fastcgi_params): fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param HTTPS $https if_not_empty; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # PHP only, required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; alsow i'm getting this on a shared hosting server, on one of the domains: Unable to generate the web server configuration file on the host because of the following errors: nginx: [warn] duplicate MIME type "text/html" in /etc/nginx/nginx.conf:45 nginx: [emerg] open() "/var/www/vhosts/partydayandnight.ro/statistics/logs/proxy_access_log" failed (24: Too many open files) nginx: configuration file /etc/nginx/nginx.conf test failed Please resolve the errors in web server configuration templates and generate the file again. why is this appearing and what troubles may it cause? what can i do to get this errors fixed? thank you!

    Read the article

  • Default gateway is in different subnet. How to configure in RHEL6.2

    - by Dmytro Leonenko
    I have two subnets routed to my server from ISP. I have only one gateway ip. The gateway is on the same VLAN as my IP address. For example netowrk 1 is 1.0.0.0/24 and network 2 is 2.0.0.0/24. Both are routed to eth0 by my ISP. Gateway is 1.0.0.1. My host ip is 2.0.0.1/24 (eth0) So I can configure default gateway manually with ip route add default dev eth0 ip route add default via 1.0.0.1 and then internet connection works properly. How do I configure it in /etc/sysconfig/network-scripts/ifcfg-eth0 ? I tried to set GATEWAY=1.0.0.1 but it doesn't work. Tried to set GATEWAY and GATEWAYDEV in /etc/sysconfig/network and it does only what first command from listing above do.

    Read the article

  • How can I redirect HTTPS(S) traffic to anothr gateway?

    - by PsyStyle
    I have a network like 192.168.0.0/15 with the default gateway set to 192.168.0.1. Al the workstations of the network use this gateway for all kind of accesses to the Internet. Now I am testing a new Internet connection with another provider and for this I am using a second gateway on the same subnet with 192.168.0.2 as IP address. I want to redirect only HTTP and HTTPS traffic to this second gateway without touching the address of the default gateway set inside every workstation. How can I accomplish this task? What I have to change inside the first's gateway firewall configuration or routes? I tried with a dnat like DNAT loc:192.168.0.1 loc:192.168.0.2 tcp 80 but nothing worked. I use Shorewall for simplicity in configuration but I can understand even theorical answers which I will try to adapt to my case

    Read the article

  • How can I redirect HTTP(S) traffic to another gateway?

    - by PsyStyle
    I have a network like 192.168.0.0/15 with the default gateway set to 192.168.0.1. All the workstations of the network use this gateway for all kind of accesses to the Internet. Now I am testing a new Internet connection with another provider and for that I'm using a second gateway on the same subnet with 192.168.0.2 as IP address. I want to redirect only HTTP and HTTPS traffic to this second gateway keeping untouched the address of the default gateway set inside every workstation. How can I accomplish this task? What I have to change inside the first's gateway firewall configuration or routes? I tried with a DNAT like: DNAT loc:192.168.0.1 loc:192.168.0.2 tcp 80 but nothing worked. I use Shorewall for simplicity in configuration but I can understand even theorical answers which I will try to adapt to my case.

    Read the article

  • C# HttpWebResponse Error 502 Bad Gateway

    - by Sten Koning
    So i'm using this class to POST on a webpage. The server i'm trying to POST to gives me a 502 Bad Gateway error. I think it has something to do with the user agent. I've already added my firefox user agent to the request but it seems to lose it on the response. I've tried using google and found some other articles on this like this one: Error 502 (Bad Gateway) when sending a request with HttpWebRequest over SSL but I don't know how to fix it since im not that good at c#. Greetings, Sten.

    Read the article

  • Default IPv6 route on debian squeeze does not come up after boot

    - by Georg Bretschneider
    I have a problem with my default IPv6 route not coming up after boot on a Debian Squeeze system. This is my config (/etc/network/interfaces): # Loopback device: auto lo iface lo inet loopback iface lo inet6 loopback # device: br0 auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 88.198.62.xx broadcast 88.198.62.63 netmask 255.255.255.224 gateway 88.198.62.33 up route add -net 88.198.62.32 netmask 255.255.255.224 gw 88.198.62.33 br0 iface br0 inet6 static address 2a01:4f8:131:10x::2 netmask 64 gateway 2a01:4f8:131:100::1 up route -A inet6 add 2a01:4f8:131:100::1/59 dev br0 My inet comes up alright, but I have to exec the route command manually after boot to make IPv6 work. Otherwise I can't even reach my gateway. This is the output of ip -6 route show after boot: 2a01:4f8:131:10x::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 unreachable fe80::/64 dev lo proto kernel metric 256 error -101 mtu 16436 advmss 16376 hoplimit 4294967295 fe80::/64 dev br0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 I already tried it with: up ip -6 route add 2a01:4f8:131:100::1 dev br0 up ip -6 route add default via 2a01:4f8:131:100::1 dev br0 in /etc/network/interfaces, but with the same results. If I execute those commands manually on my shell, everything starts working nicely. And yes, I tried with post-up instead of up, too. Only other changes I made was to activate ip forwarding for IPv6, because I want to run some LXC containers on that system.

    Read the article

  • Two DHCP interfaces asigned to two default gateways to OS

    - by user140600
    I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

    Read the article

  • How to integrate cardinalcommerce authentication processing in a flash and Asp.net project?

    - by Krishnan
    Our Asp.net//Flash team doing a shopping cart project. We are integrating First Data Alternative payment gateway. Shopping cart items are selected through flash and our asp.net team taking the data from flash and integrating the first data alternative payment. We have already integrated first data payment gateway. Now we want to integrate First Data Alternative payment gateway. Please help our team to do so

    Read the article

  • Efficiently select top row for each category in the set

    - by VladV
    I need to select a top row for each category from a known set (somewhat similar to this question). The problem is, how to make this query efficient on the large number of rows. For example, let's create a table that stores temperature recording in several places. CREATE TABLE #t ( placeId int, ts datetime, temp int, PRIMARY KEY (ts, placeId) ) -- insert some sample data SET NOCOUNT ON DECLARE @n int, @ts datetime SELECT @n = 1000, @ts = '2000-01-01' WHILE (@n>0) BEGIN INSERT INTO #t VALUES (@n % 10, @ts, @n % 37) IF (@n % 10 = 0) SET @ts = DATEADD(hour, 1, @ts) SET @n = @n - 1 END Now I need to get the latest recording for each of the places 1, 2, 3. This way is efficient, but doesn't scale well (and looks dirty). SELECT * FROM ( SELECT TOP 1 placeId, temp FROM #t WHERE placeId = 1 ORDER BY ts DESC ) t1 UNION ALL SELECT * FROM ( SELECT TOP 1 placeId, temp FROM #t WHERE placeId = 2 ORDER BY ts DESC ) t2 UNION ALL SELECT * FROM ( SELECT TOP 1 placeId, temp FROM #t WHERE placeId = 3 ORDER BY ts DESC ) t3 The following looks better but works much less efficiently (30% vs 70% according to the optimizer). SELECT placeId, ts, temp FROM ( SELECT placeId, ts, temp, ROW_NUMBER() OVER (PARTITION BY placeId ORDER BY ts DESC) rownum FROM #t WHERE placeId IN (1, 2, 3) ) t WHERE rownum = 1 The problem is, during the latter query execution plan a clustered index scan is performed on #t and 300 rows are retrieved, sorted, numbered, and then filtered, leaving only 3 rows. For the former query three times one row is fetched. Is there a way to perform the query efficiently without lots of unions?

    Read the article

  • How to open an iPhone compatible M3U file on Windows?

    - by user1158667
    This is how the M3U file looks like: #EXTM3U #EXT-X-STREAM-INF:PROGRAM-ID=1,BANDWIDTH=1400000 http://maskedip/http_livestr.str?r=true&id=mbit-test&k=testkey #EXT-X-STREAM-INF:PROGRAM-ID=1,BANDWIDTH=900000 http://maskedip/http_livestr.str?r=true&id=test&k=testkey #EXT-X-STREAM-INF:PROGRAM-ID=1,BANDWIDTH=450000 http://maskedip/http_livestr.str?r=true&id=mobile-test&k=testkey #EXT-X-STREAM-INF:PROGRAM-ID=1,CODECS="mp4a.40.2",BANDWIDTH=64000 http://maskedup/http_livestr.str?r=true&id=test-audio&k=testkey Clicking on http://maskedip/http_livestr.str?r=true&id=mbit-test&k=testkey then returns another M3U file in this format: #EXTM3U #EXT-X-TARGETDURATION:10 #EXT-X-MEDIA-SEQUENCE:1361 #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1361.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1362.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1363.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1364.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1365.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1366.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1367.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1368.ts #EXTINF:10, http://maskedip/http_ls/testkey/mbit-test1/1369.ts Anyways, VLC won't recognize it. How can I play this on the PC?

    Read the article

  • What are some reputable merchant account providers for high risk payment web sites?

    - by GregH
    I am helping to set up an online cigar web site. However, it has become a real pain to take payments online since tobacco is considered a "high-risk" item and nobody will provide a merchant account to process the payments. It looks like there are companies that specialize in high-risk merchant accounts. I was wondering if anybody could recommend a high-risk merchant account and payment processing provider?

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >