tcp port - Page 121 - Developer IT

How to connect 2 routers (Asmax and D-link)

- by piobyz

I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

Read the article

Not getting IP from ISP on Multicast Network

- by Johan Nielsen

Im having an odd issue with my ISP (COMX.dk) I have a managed access gateway box (Telsay) with three 8P8C ports for use with Internet and Ip-Tv (respectively on different VLANS (so does my ISP tell me)) To utilize a port you will need to register your device's mac address through an online interface. You will then get your device paired with a static ip. I am using one port actively and I have registered another device (router). The router is configured to listen for an active dhcpd on the network. When my router get a lease I get a private ip 192.168.2.2 (not the one bound to my mac) which is odd! I unconnected my router from the gateway and connected my laptop directly. Same thing happened - I was given a private address. I did a port scan on the gateway and found port 80 to be open and browsed to the ip. I was then presented with a management interface of a Belkin wireless router (HMMM!!!!) <--by the way, not my gear At this point I called the ISP to let them know of my issue/findings - Only to be replied "Well, we cant see any rogue dhcp servers" (thinking to myself, well I can) I then decided that it could be fun to try the other port of my gateway, only to experience the same. So I reconnected my router and used the remaining port to make an observer(wireshark promic etc.) I am able to see my router trying to discover a dhcp server but I can also see my ISP's IGMP and PIMv2 packages just repeating the same pattern. Hello...Hello...Hello :) So I called them again, only to get the same response, "we dont see any rogue dhcp's...we cant see the host you are talking to (mac address of the Belkin router)...you are definitively connected through wireless?!?(no im not, no such thing as a wireless wire - i thought to myself)" My questions is, What is going on? (besides from what im reporting here) What am I seeing that the don't? What can I tell them in order for them to resolve mine/their issue?

Read the article

HP dv6910 laptop no longer recognizes wireless adapter, dvd drive, and one usb port. What can I do about this?

- by Joan H.

In the last 3 weeks, my not even 3 year old HP laptop (vista) just seems to be failing. First, one of the usb ports stopped working. Next, the dvd drive all of a sudden was not recognized as even existing, so it is now useless. And as of today, I no longer seem to have a wireless adapter on my laptop. It doesn't show up in device manager, same as the dvd drive. I can connect to the internet by ethernet cable, but not wirelessly. It worked fine last night; now it doesn't even exist! I have tried a 'hard reset' I read about on HP's forum- no help. I am not sure what else to try. I read about the USB wifi dongle in another response, but I already have maxed our my usb ports even though I have bought a USB hub since the one port failed. Plus, I'd like my laptop to just work like it's supposed to instead of being jerry rigged with usb hubs, external dvd drives, and wifi dongles etc. Any ideas?

Read the article

How to play WAV file through Network Paging Interface

- by BGM

In our building we have a Viking Paging ZPI-4 Interface for our intercom. The interface receives data from our Asterisk Phone system via a Cisco SPA112 Port Adapter which has it's own IP address on the network and converts digital into analog. Asterisk plays the "5" tone and then allows the user's voice to commence over the connection. Now, what I want to do is to play a wav file over this Viking Paging device using the Cisco Port Adapter. I know how to get Asterisk to do it, but I want to do this without Asterisk. I want some kind of program that can talk to the Cisco Port Adapter and then transmit the wav file into the Viking Paging Device. What kind of program do I need to get or make? Now, I found this link if it helps anyone with ideas. I also found this information, but I'm not sure how to apply it. I also found this, but it involves an arduino. However, I already have the analog-to-digital convertor, and the Viking will handle sending sound over the paging speakers. I just need to know how to send the wav file to the Viking via the Port Adapter. So far, I know my wav file should be formatted as 8bit mono, and I need to send the "5" tone to open the Viking Pager's channel. [update] I am trying to figure out if I can use VLC player to stream to the ipaddress of the Port Adapter. So far I'm not having success with that, and don't even know if it will work. Windows Media Player has a streaming option too. I am thinking that since the Cisco Port Adapter thinks it is a sort of phone, that the only way this can be done is via SIP.

Read the article

Simple vLAN setup

- by Logan Bissonnette

I have a basic lab environment set up to try and get 2 vLANs working in hyper-v. I have the following equipment 1 hyper-v server 1 Desktop PC 1 Managed Switch (d-link DES-3052P) 1 cheap router (DI-604) My end goal is to have 1 VM and the desktop on one vLAN with internet, and 1 VM on a separate vLAN with internet access. I am having troubles getting an internet connection to both vLANs. The switch does not have the ability to have asynchronous vLANs. This is my switch configuration Port 1 - Trunk Port - Connected to router Port 2 - Trunk Port - Connected to hyper-v Server Port 3 - Access Port- Connected to Desktop Within hyper-v I have 1 switch and 2 VMs. When the VMs are set up to use vlan ID 1, everything works fine. As soon as a VM is set up to use vlan ID 2, they lose all network connection and cannot communicate with the router anymore. I believe this is because the router is not vLAN aware. Can anyone help me with what settings need to be set up on my switch? I believe I want an egress rule so traffic leaving towards the router is untagged, is that right? If not, any ideas or hints as to what needs to be set up?

Read the article

esx5 debian VM vlan setup

- by Kstro21

i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

Read the article

use ssh tunnel with phpmyadmin

- by JohnMerlino

I been using ssh tunnel to bypass firewall of remote mysql server. On my Ubuntu 12.04 installation, it works via the terminal and it works when using a program called mysql workbench. However, that program freezes often and I want to try phpmyadmin as an alternative. However, I cannot connect to remote server using ssh tunnel on phpmyadmin, albeit I can connect locally. These are the steps I've tried: 1) Open a tunnel, listening on localhost:3307 and forwarding everything to xxx.xxx.xxx.xxx:3306 (used 3307 because MySQL on my local machine uses the default port 3306): ssh -L 3307:localhost:3306 [email protected] So now I have the port for tunnel open and I have my local mysql installation default port: $ netstat -tln Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3307 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN ... 2) Now I can easily connect to remote server via localhost using the terminal: $ mysql -u user.name -p -h 127.0.0.1 -P 3307 Notice that I expicitly identify 3307 as the port, so traffic forwards to the remote server, and hence it logs me in to the remote server. Unfortunately, the localhost/phpmyadmin local login interface doesn't allow you to specify a port option. So I modify the config-db.php file and change the $dbport variable to 3307, under the impression that the phpmyadmin interface will now work with port 3307: $ sudo vim /etc/phpmyadmin/config-db.php $dbport='3307'; Then I restart the mysql server. Unfortunately, it didn't work. When I use the remote credentials to login, it gives me error: #1045 Cannot log in to the MySQL server

Read the article

C# listview add items

- by Eyla

Greetings, I have a method to capture packets. after capturing I want to add each packet as a row in listview in runting time so as soon as I capture packet I want to add it to the list view. the problem that when I use items.Add() I will get overload argument error. please advice!! here is my code: private void packetCapturingThreadMethod() { Packet packet = null; int countOfPacketCaptures = 0; while ((packet = device.GetNextPacket()) != null) { packet = device.GetNextPacket(); if (packet is TCPPacket) { TCPPacket tcp = (TCPPacket)packet; myPacket tempPacket = new myPacket(); tempPacket.packetType = "TCP"; tempPacket.sourceAddress = Convert.ToString(tcp.SourceAddress); tempPacket.destinationAddress = Convert.ToString(tcp.DestinationAddress); tempPacket.sourcePort = Convert.ToString(tcp.SourcePort); tempPacket.destinationPort = Convert.ToString(tcp.DestinationPort); tempPacket.packetMessage = Convert.ToString(tcp.Data); packetsList.Add(tempPacket); string[] row = { packetsList[countOfPacketCaptures].packetType, packetsList[countOfPacketCaptures].sourceAddress, packetsList[countOfPacketCaptures].destinationAddress, packetsList[countOfPacketCaptures].sourcePort, packetsList[countOfPacketCaptures].destinationPort, packetsList[countOfPacketCaptures].packetMessage }; try { listView1.Items.Add(packetsList[countOfPacketCaptures].packetType, packetsList[countOfPacketCaptures].sourceAddress, packetsList[countOfPacketCaptures].destinationAddress, packetsList[countOfPacketCaptures].sourcePort, packetsList[countOfPacketCaptures].destinationPort, packetsList[countOfPacketCaptures].packetMessage) ; countOfPacketCaptures++; lblCapturesLabels.Text = Convert.ToString(countOfPacketCaptures);} catch (Exception e) { } } else if (packet is UDPPacket) { UDPPacket udp = (UDPPacket)packet; myPacket tempPacket = new myPacket(); tempPacket.packetType = "UDP"; tempPacket.sourceAddress = Convert.ToString(udp.SourceAddress); tempPacket.destinationAddress = Convert.ToString(udp.DestinationAddress); tempPacket.sourcePort = Convert.ToString(udp.SourcePort); tempPacket.destinationPort = Convert.ToString(udp.DestinationPort); tempPacket.packetMessage = Convert.ToString(udp.Data); packetsList.Add(tempPacket); string[] row = { packetsList[countOfPacketCaptures].packetType, packetsList[countOfPacketCaptures].sourceAddress, packetsList[countOfPacketCaptures].destinationAddress, packetsList[countOfPacketCaptures].sourcePort, packetsList[countOfPacketCaptures].destinationPort, packetsList[countOfPacketCaptures].packetMessage }; try { dgwPacketInfo.Rows.Add(row); countOfPacketCaptures++; lblCapturesLabels.Text = Convert.ToString(countOfPacketCaptures); } catch (Exception e) { } } } }

Read the article

LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

- by Andy Shinn

I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 mirrors. The problem I am running in to is that there are duplicate slots for the 2 chassis (the slots list twice and only go from 0 to 27). All the drives also show the same enclosure ID (ID 36). However, MegaCLI -encinfo lists the 2 enclosures correctly (ID 36 and ID 65). My question is, why would this happen? Is there an option I am missing to use 2 enclosures effectively? This is blocking me rebuilding a drive that failed in slot 11 since I can only specify enclosure and slot as parameters to replace a drive. When I do this, it picks the wrong slot 11 (device ID 46 instead of device ID 19). Adapter #1 is the LSI 9285-8e, adapter #0 (which I removed due to space limitations) is the onboard LSI. Adapter information: Adapter #1 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS 9285-8e Serial No : SV12704804 FW Package Build: 23.1.1-0004 Mfg. Data ================ Mfg. Date : 06/30/11 Rework Date : 00/00/00 Revision No : 00A Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 5.25.00_4.11.05.00_0x05040000 WebBIOS Version : 6.1-20-e_20-Rel Preboot CLI Version: 05.01-04:#%00001 FW Version : 3.140.15-1320 NVDATA Version : 2.1106.03-0051 Boot Block Version : 2.04.00.00-0001 BOOT Version : 06.253.57.219 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 005b SubVendorId : 1000 SubDeviceId : 9285 Host Interface : PCIE ChipRevision : B0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5003048000ee8e7f 1 5003048000ee8a7f 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b0038f9210 BBU : Present Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 70 degree Celcius Settings ================ Current Time : 18:24:36 3/13, 2012 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : Disabled Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 887 MB Device Present ================ Virtual Drives : 28 Degraded : 0 Offline : 0 Physical Devices : 59 Disks : 56 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : No Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : Yes Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : Yes Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : None ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00 Enclosure information: # /opt/MegaRAID/MegaCli/MegaCli64 -encinfo -a1 Number of enclosures on adapter 1 -- 3 Enclosure 0: Device ID : 36 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port B Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 65 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11820 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 48 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 1: Device ID : 65 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port A Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 36 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11760 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 47 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 2: Device ID : 252 Number of Slots : 8 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 1 Number of Physical Drives : 0 Status : Normal Position : 1 Connector Name : Unavailable Enclosure type : SGPIO Failed in first Inquiry commnad FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : Unavailable Inquiry data : Vendor Identification : LSI Product Identification : SGPIO Product Revision Level : N/A Vendor Specific : Exit Code: 0x00 Now, notice that each slot 11 device shows an enclosure ID of 36, I think this is where the discrepancy happens. One should be 36. But the other should be on enclosure 65. Drives in slot 11: Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 5, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 48 WWN: Sequence Number: 11 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : YES Device Firmware Level: A5C0 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8a53 Connected Port Number: 1(path0) Inquiry Data: MJ1311YNG6YYXAHitachi HDS5C3030ALA630 MEAOA5C0 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 19, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 19 WWN: Sequence Number: 4 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : NO Device Firmware Level: A580 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8e53 Connected Port Number: 0(path0) Inquiry Data: MJ1313YNG1VA5CHitachi HDS5C3030ALA630 MEAOA580 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Update 06/28/12: I finally have some new information about (what we think) the root cause of this problem so I thought I would share. After getting in contact with a very knowledgeable Supermicro tech, they provided us with a tool called Xflash (doesn't appear to be readily available on their FTP). When we gathered some information using this utility, my colleague found something very strange: root@mogile2 test]# ./xflash.dat -i get avail Initializing Interface. Expander: SAS2X36 (SAS2x36) 1) SAS2X36 (SAS2x36) (50030480:00EE917F) (0.0.0.0) 2) SAS2X36 (SAS2x36) (50030480:00E9D67F) (0.0.0.0) 3) SAS2X36 (SAS2x36) (50030480:0112D97F) (0.0.0.0) This lists the connected enclosures. You see the 3 connected (we have since added a 3rd and a 4th which is not yet showing up) with their respective SAS address / WWN (50030480:00EE917F). Now we can use this address to get information on the individual enclosures: [root@mogile2 test]# ./xflash.dat -i 5003048000EE917F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00EE917F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 5003048000E9D67F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00E9D67F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 500304800112D97F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:0112D97F Enclosure Logical Id: 50030480:0112D97F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 Did you catch it? The first 2 enclosures logical ID is partially masked out where the 3rd one (which has a correct unique enclosure ID) is not. We pointed this out to Supermicro and were able to confirm that this address is supposed to be set during manufacturing and there was a problem with a certain batch of these enclosures where the logical ID was not set. We believe that the RAID controller is determining the ID based on the logical ID and since our first 2 enclosures have the same logical ID, they get the same enclosure ID. We also confirmed that 0000007F is the default which comes from LSI as an ID. The next pointer that helps confirm this could be a manufacturing problem with a run of JBODs is the fact that all 6 of the enclosures that have this problem begin with 00E. I believe that between 00E8 and 00EE Supermicro forgot to program the logical IDs correctly and neglected to recall or fix the problem post production. Fortunately for us, there is a tool to manage the WWN and logical ID of the devices from Supermicro: ftp://ftp.supermicro.com/utility/ExpanderXtools_Lite/. Our next step is to schedule a shutdown of these JBODs (after data migration) and reprogram the logical ID and see if it solves the problem. Update 06/28/12 #2: I just discovered this FAQ at Supermicro while Google searching for "lsi 0000007f": http://www.supermicro.com/support/faqs/faq.cfm?faq=11805. I still don't understand why, in the last several times we contacted Supermicro, they would have never directed us to this article :\

Read the article

What is "Disable class based route addition" good for?

- by id.roppert.dejroppert

In the advanced TCP/IP settings of a VPN connection, i found a checkbox labeled with "Disable class based route addition". The checkbox is only enabled as long as "Use default gateway on remote network" is switched off. What is "Disable class based route addition" good for? Detailed instructions to find the settings: Open Properties of VPN connection Go to Networking tab Open Properties of "Internet Protocol Version 4 (TCP/IPv4)" (and/or TCP/IPv6) Click "Advanced..." Button Change to "IP Settings" tab Here you can find the checkboxes mentioned above

Read the article

Handshake violation when trying to access one website

- by Miguel

I have a TZ 190 Wireless Enhanced with SonicOS Enhanced 4.2.1.0-20e. Yesterday, people could access without any problems a bank website wich uses HTTPS. Today, it is imposible to access only that website, every other ones works without problems. When checking the log message filtering to my IP only, this is what appears and I suspect is the cause of this problem, because all other websites are working: Priority: Notice Category: Network Access Message: TCP handshake violation detected; TCP connection dropped Source: X.Y.Z.3, 51997, LAN (admin) Destination: 200.14.232.18, 443, WAN Notes: Handshake Timeout Where X.Y.Z.3 is my local IP. I've tried to change TCP Settings under Firewall option, and activated this options with no success: Enforce strict TCP compliance with RFC 793 and RFC 1122 and Enable TCP checksum enforcement I've also tried to find the MTU and at first I got: Packet needs to be fragmented but DF set But when I lower the value of ping -f -l to 1468 I got: Request timeout. Also I deactivate CFS in lan and wan zones. Nothing works. Can you please help me? Any Ideas?

Read the article

Openvpn plugin openvpn-auth-ldap does not bind to Active Directory

- by Selivanov Pavel

I'm trying to configure OpenVPN with openvpn-auth-ldap plugin to authorize users via Active Directory LDAP. When I use the same server config without plugin option, and add client config with generated client key and cert, connection is successful, so problem is in the plugin. server.conf: plugin /usr/lib/openvpn/openvpn-auth-ldap.so "/etc/openvpn-test/openvpn-auth-ldap.conf" port 1194 proto tcp dev tun keepalive 10 60 topology subnet server 10.0.2.0 255.255.255.0 tls-server ca ca.crt dh dh1024.pem cert server.crt key server.key #crl-verify crl.pem persist-key persist-tun user nobody group nogroup verb 3 mute 20 openvpn-auth-ldap.conf: <LDAP> URL ldap://dc1.domain:389 TLSEnable no BindDN cn=bot_auth,cn=Users,dc=domain Password bot_auth Timeout 15 FollowReferrals yes </LDAP> <Authorization> BaseDN "cn=Users,dc=domain" SearchFilter "(sAMAccountName=%u)" RequireGroup false # <Group> # BaseDN "ou=groups,dc=mycompany,dc=local" # SearchFilter "(|(cn=developers)(cn=artists))" # MemberAttribute uniqueMember # </Group> </Authorization> Top-level domain in AD is used by historical reasons. Analogue configuration is working for Apache 2.2 in mod-authzn-ldap. User and password are correct. client.conf: remote server_name port 1194 proto tcp client pull remote-cert-tls server dev tun resolv-retry infinite nobind ca ca.crt ; with keys - works fine #cert test.crt #key test.key ; without keys - by password auth-user-pass persist-tun verb 3 mute 20 In server log there is string PLUGIN_INIT: POST /usr/lib/openvpn/openvpn-auth-ldap.so '[/usr/lib/openvpn/openvpn-auth-ldap.so] [/etc/openvpn-test/openvpn-auth-ldap.conf]' which indicates, that plugin failed. I can telnet to dc1.domain:389, so this is not network/firewall problem. Later server says TLS Error: TLS object -> incoming plaintext read error TLS handshake failed - without plugin it tryes to do usal key authentification. server log: Tue Nov 22 03:06:20 2011 OpenVPN 2.1.3 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Oct 21 2010 Tue Nov 22 03:06:20 2011 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Nov 22 03:06:20 2011 PLUGIN_INIT: POST /usr/lib/openvpn/openvpn-auth-ldap.so '[/usr/lib/openvpn/openvpn-auth-ldap.so] [/etc/openvpn-test/openvpn-auth-ldap.conf]' intercepted=PLUGIN_AUTH_USER_PASS_VERIFY|PLUGIN_CLIENT_CONNECT|PLUGIN_CLIENT_DISCONNECT Tue Nov 22 03:06:20 2011 Diffie-Hellman initialized with 1024 bit key Tue Nov 22 03:06:20 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue Nov 22 03:06:20 2011 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Nov 22 03:06:20 2011 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:20 2011 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:20 2011 TLS-Auth MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:06:20 2011 Socket Buffers: R=[87380->131072] S=[16384->131072] Tue Nov 22 03:06:20 2011 TUN/TAP device tun1 opened Tue Nov 22 03:06:20 2011 TUN/TAP TX queue length set to 100 Tue Nov 22 03:06:20 2011 /sbin/ifconfig tun1 10.0.2.1 netmask 255.255.255.0 mtu 1500 broadcast 10.0.2.255 Tue Nov 22 03:06:20 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:06:20 2011 GID set to nogroup Tue Nov 22 03:06:20 2011 UID set to nobody Tue Nov 22 03:06:20 2011 Listening for incoming TCP connection on [undef] Tue Nov 22 03:06:20 2011 TCPv4_SERVER link local (bound): [undef] Tue Nov 22 03:06:20 2011 TCPv4_SERVER link remote: [undef] Tue Nov 22 03:06:20 2011 MULTI: multi_init called, r=256 v=256 Tue Nov 22 03:06:20 2011 IFCONFIG POOL: base=10.0.2.2 size=252 Tue Nov 22 03:06:20 2011 MULTI: TCP INIT maxclients=1024 maxevents=1028 Tue Nov 22 03:06:20 2011 Initialization Sequence Completed Tue Nov 22 03:07:10 2011 MULTI: multi_create_instance called Tue Nov 22 03:07:10 2011 Re-using SSL/TLS context Tue Nov 22 03:07:10 2011 Control Channel MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:07:10 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:07:10 2011 Local Options hash (VER=V4): 'c413e92e' Tue Nov 22 03:07:10 2011 Expected Remote Options hash (VER=V4): 'd8421bb0' Tue Nov 22 03:07:10 2011 TCP connection established with [AF_INET]10.0.0.9:47808 Tue Nov 22 03:07:10 2011 TCPv4_SERVER link local: [undef] Tue Nov 22 03:07:10 2011 TCPv4_SERVER link remote: [AF_INET]10.0.0.9:47808 Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS: Initial packet from [AF_INET]10.0.0.9:47808, sid=a2cd4052 84b47108 Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS_ERROR: BIO read tls_read_plaintext error: error:140890C7:SSL routines:SSL3_GET_CLIENT_CERTIFICATE:peer did not return a certificate Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS Error: TLS object -> incoming plaintext read error Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS Error: TLS handshake failed Tue Nov 22 03:07:11 2011 10.0.0.9:47808 Fatal TLS error (check_tls_errors_co), restarting Tue Nov 22 03:07:11 2011 10.0.0.9:47808 SIGUSR1[soft,tls-error] received, client-instance restarting Tue Nov 22 03:07:11 2011 TCP/UDP: Closing socket client log: Tue Nov 22 03:06:18 2011 OpenVPN 2.1.3 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Oct 22 2010 Enter Auth Username:user Enter Auth Password: Tue Nov 22 03:06:25 2011 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Nov 22 03:06:25 2011 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Nov 22 03:06:25 2011 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:25 2011 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:25 2011 Control Channel MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:06:25 2011 Socket Buffers: R=[87380->131072] S=[16384->131072] Tue Nov 22 03:06:25 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:06:25 2011 Local Options hash (VER=V4): 'd8421bb0' Tue Nov 22 03:06:25 2011 Expected Remote Options hash (VER=V4): 'c413e92e' Tue Nov 22 03:06:25 2011 Attempting to establish TCP connection with [AF_INET]10.0.0.2:1194 [nonblock] Tue Nov 22 03:06:26 2011 TCP connection established with [AF_INET]10.0.0.2:1194 Tue Nov 22 03:06:26 2011 TCPv4_CLIENT link local: [undef] Tue Nov 22 03:06:26 2011 TCPv4_CLIENT link remote: [AF_INET]10.0.0.2:1194 Tue Nov 22 03:06:26 2011 TLS: Initial packet from [AF_INET]10.0.0.2:1194, sid=7a3c2a0f bd35bca7 Tue Nov 22 03:06:26 2011 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Tue Nov 22 03:06:26 2011 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funston/CN=Fort-Funston_CA/[email protected] Tue Nov 22 03:06:26 2011 Validating certificate key usage Tue Nov 22 03:06:26 2011 ++ Certificate has key usage 00a0, expects 00a0 Tue Nov 22 03:06:26 2011 VERIFY KU OK Tue Nov 22 03:06:26 2011 Validating certificate extended key usage Tue Nov 22 03:06:26 2011 ++ Certificate has EKU (str) TLS Web Server Authentication, expects TLS Web Server Authentication Tue Nov 22 03:06:26 2011 VERIFY EKU OK Tue Nov 22 03:06:26 2011 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funston/CN=server/[email protected] Tue Nov 22 03:06:26 2011 Connection reset, restarting [0] Tue Nov 22 03:06:26 2011 TCP/UDP: Closing socket Tue Nov 22 03:06:26 2011 SIGUSR1[soft,connection-reset] received, process restarting Tue Nov 22 03:06:26 2011 Restart pause, 5 second(s) ^CTue Nov 22 03:06:27 2011 SIGINT[hard,init_instance] received, process exiting Does anybody know how to get openvpn-auth-ldap wirking?

Read the article

SQL Server 08 Express error when connecting to localhost - "Timeout expired". Works with ::1 or 127

- by Adam A

EDIT New info: Navigating to localhost:1434 in Chrome gives me an "ERR_EMPTY_RESPONSE", while other ports give me an "Oops! This link appears to be broken". So it seems to binding ok there? So here's my setup so far: I've configured Windows Firewall to allow TCP on 1433 and UDP on 1434. I've set up SQL Server to use any IP on Port 1433 (using the SQL Server Configuration Manager). My hosts file contains the default entries ("127.0.0.1 localhost" and "::1 localhost"). I sometimes have a debug session of Visual Web Developer running a webserver, but it's on a specific port (localhost:5XXXX). What I've tried: I CAN ping localhost in a cmd prompt. I CAN connect to the database through SSMS if I specify 127.0.0.1 or ::1 as the server name. I CAN'T connect to the database through SSMS (or ADO.NET) if I specify localhost as the server name. I've tried both Windows and SQL Authentication The error I get is the standard Can't connect to localhost. Additional Information -- Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft Sql Server) Other considerations: Stopping the Visual Web Developer web server from the taskbar doesn't affect the sql problem. The SQL error log says that it's listening on some piped name url at start up (I don't see how this would affect localhost but not 127.0.0.1 though). I could probably just use 127.0.0.1 everywhere, but it scares me that localhost isn't working and I'd like to figure out why. I'm not much of a networking or sql server guy so I'm stuck. If you want me to try anything to help diagnose just put it in a comment and I'll give it a go. Netstat results: Setting SDK environment relative to C:\Program Files\Microsoft SDKs\Windows\v6.1 Targeting Windows Server 2008 x86 DEBUG C:\Program Files\Microsoft SDKs\Windows\v6.1netstat -ano | findstr 1434 UDP 0.0.0.0:1434 *:* 6868 UDP [::]:1434 *:* 6868 C:\Program Files\Microsoft SDKs\Windows\v6.1netstat -ano | findstr 1433 TCP 0.0.0.0:1433 0.0.0.0:0 LISTENING 2268 TCP 127.0.0.1:1433 127.0.0.1:50758 ESTABLISHED 2268 TCP 127.0.0.1:50758 127.0.0.1:1433 ESTABLISHED 5008 TCP [::]:1433 [::]:0 LISTENING 2268 TCP [::1]:1433 [::1]:51202 ESTABLISHED 2268 TCP [::1]:1433 [::1]:51616 ESTABLISHED 2268 TCP [::1]:51202 [::1]:1433 ESTABLISHED 5008 TCP [::1]:51616 [::1]:1433 ESTABLISHED 5008 C:\Program Files\Microsoft SDKs\Windows\v6.1 SQL Server Log File: In case it helps 2010-01-30 12:58:59.01 Server Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) 2010-01-30 12:58:59.01 Server (c) 2005 Microsoft Corporation. 2010-01-30 12:58:59.01 Server All rights reserved. 2010-01-30 12:58:59.01 Server Server process ID is 2268. 2010-01-30 12:58:59.01 Server System Manufacturer: 'Dell Inc.', System Model: 'Inspiron 1545'. 2010-01-30 12:58:59.01 Server Authentication mode is MIXED. 2010-01-30 12:58:59.02 Server Logging SQL Server messages in file 'c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\Log\ERRORLOG'. 2010-01-30 12:58:59.02 Server This instance of SQL Server last reported using a process ID of 7396 at 1/30/2010 12:57:38 PM (local) 1/30/2010 5:57:38 PM (UTC). This is an informational message only; no user action is required. 2010-01-30 12:58:59.02 Server Registry startup parameters: -d c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\DATA\master.mdf -e c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\Log\ERRORLOG -l c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\DATA\mastlog.ldf 2010-01-30 12:58:59.02 Server SQL Server is starting at normal priority base (=7). This is an informational message only. No user action is required. 2010-01-30 12:58:59.02 Server Detected 2 CPUs. This is an informational message; no user action is required. 2010-01-30 12:58:59.08 Server Using dynamic lock allocation. Initial allocation of 2500 Lock blocks and 5000 Lock Owner blocks per node. This is an informational message only. No user action is required. 2010-01-30 12:58:59.17 Server Node configuration: node 0: CPU mask: 0x00000003 Active CPU mask: 0x00000003. This message provides a description of the NUMA configuration for this computer. This is an informational message only. No user action is required. 2010-01-30 12:58:59.30 spid7s Starting up database 'master'. 2010-01-30 12:58:59.41 spid7s Recovery is writing a checkpoint in database 'master' (1). This is an informational message only. No user action is required. 2010-01-30 12:58:59.67 spid7s FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'SQLEXPRESS'. 2010-01-30 12:58:59.92 spid7s SQL Trace ID 1 was started by login "sa". 2010-01-30 12:58:59.94 spid7s Starting up database 'mssqlsystemresource'. 2010-01-30 12:58:59.95 spid7s The resource database build version is 10.00.2531. This is an informational message only. No user action is required. 2010-01-30 12:59:00.82 spid7s Server name is 'DELL\SQLEXPRESS'. This is an informational message only. No user action is required. 2010-01-30 12:59:00.83 Server A self-generated certificate was successfully loaded for encryption. 2010-01-30 12:59:00.84 Server Server is listening on [ 'any' 1433]. 2010-01-30 12:59:00.84 Server Server is listening on [ 'any' 1433]. 2010-01-30 12:59:00.84 spid10s Starting up database 'model'. 2010-01-30 12:59:00.85 Server Server local connection provider is ready to accept connection on [ \\.\pipe\SQLLocal\SQLEXPRESS ]. 2010-01-30 12:59:00.86 Server Server local connection provider is ready to accept connection on [ \\.\pipe\MSSQL$SQLEXPRESS\sql\query ]. 2010-01-30 12:59:00.86 Server Dedicated administrator connection support was not started because it is disabled on this edition of SQL Server. If you want to use a dedicated administrator connection, restart SQL Server using the trace flag 7806. This is an informational message only. No user action is required. 2010-01-30 12:59:00.87 Server The SQL Server Network Interface library could not register the Service Principal Name (SPN) for the SQL Server service. Error: 0x54b, state: 3. Failure to register an SPN may cause integrated authentication to fall back to NTLM instead of Kerberos. This is an informational message. Further action is only required if Kerberos authentication is required by authentication policies. 2010-01-30 12:59:00.87 spid7s Informational: No full-text supported languages found. 2010-01-30 12:59:00.87 Server SQL Server is now ready for client connections. This is an informational message; no user action is required. 2010-01-30 12:59:00.91 spid7s Starting up database 'msdb'. 2010-01-30 12:59:01.21 spid10s Clearing tempdb database. 2010-01-30 12:59:02.78 spid10s Starting up database 'tempdb'. 2010-01-30 12:59:03.30 spid13s The Service Broker protocol transport is disabled or not configured. 2010-01-30 12:59:03.30 spid13s The Database Mirroring protocol transport is disabled or not configured. 2010-01-30 12:59:03.31 spid7s Recovery is complete. This is an informational message only. No user action is required. 2010-01-30 12:59:03.31 spid13s Service Broker manager has started.

Read the article

Cisco ASA (Client VPN) to LAN - through second VPN to second LAN

- by user50855

We have 2 site that is linked by an IPSEC VPN to remote Cisco ASAs: Site 1 1.5Mb T1 Connection Cisco(1) 2841 Site 2 1.5Mb T1 Connection Cisco 2841 In addition: Site 1 has a 2nd WAN 3Mb bonded T1 Connection Cisco 5510 that connects to same LAN as Cisco(1) 2841. Basically, Remote Access (VPN) users connecting through Cisco ASA 5510 needs access to a service at the end of Site 2. This is due to the way the service is sold - Cisco 2841 routers are not under our management and it is setup to allow connection from local LAN VLAN 1 IP address 10.20.0.0/24. My idea is to have all traffic from Remote Users through Cisco ASA destined for Site 2 to go via the VPN between Site 1 and Site 2. The end result being all traffic that hits Site 2 has come via Site 1. I'm struggling to find a great deal of information on how this is setup. So, firstly, can anyone confirm that what I'm trying to achieve is possible? Secondly, can anyone help me to correct the configuration bellow or point me in the direction of an example of such a configuration? Many Thanks. interface Ethernet0/0 nameif outside security-level 0 ip address 7.7.7.19 255.255.255.240 interface Ethernet0/1 nameif inside security-level 100 ip address 10.20.0.249 255.255.255.0 object-group network group-inside-vpnclient description All inside networks accessible to vpn clients network-object 10.20.0.0 255.255.255.0 network-object 10.20.1.0 255.255.255.0 object-group network group-adp-network description ADP IP Address or network accessible to vpn clients network-object 207.207.207.173 255.255.255.255 access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any source-quench access-list outside_access_in extended permit icmp any any unreachable access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit tcp any host 7.7.7.20 eq smtp access-list outside_access_in extended permit tcp any host 7.7.7.20 eq https access-list outside_access_in extended permit tcp any host 7.7.7.20 eq pop3 access-list outside_access_in extended permit tcp any host 7.7.7.20 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq https access-list outside_access_in extended permit tcp any host 7.7.7.21 eq 5721 access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient any access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient object-group group-adp-network access-list acl-vpnclient extended permit ip object-group group-adp-network object-group group-inside-vpnclient access-list PinesFLVPNTunnel_splitTunnelAcl standard permit 10.20.0.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 10.20.1.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 host 207.207.207.173 access-list inside_nat0_outbound_1 extended permit ip 10.20.1.0 255.255.255.0 host 207.207.207.173 ip local pool VPNPool 10.20.1.100-10.20.1.200 mask 255.255.255.0 route outside 0.0.0.0 0.0.0.0 7.7.7.17 1 route inside 207.207.207.173 255.255.255.255 10.20.0.3 1 crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 288000 crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set reverse-route crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto map outside_dyn_map 20 match address acl-vpnclient crypto map outside_dyn_map 20 set security-association lifetime seconds 28800 crypto map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto isakmp identity address crypto isakmp enable outside crypto isakmp policy 20 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 group-policy YeahRightflVPNTunnel internal group-policy YeahRightflVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 vpn-tunnel-protocol IPSec password-storage disable pfs disable split-tunnel-policy tunnelspecified split-tunnel-network-list value acl-vpnclient default-domain value YeahRight.com group-policy YeahRightFLVPNTunnel internal group-policy YeahRightFLVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 10.20.0.7 vpn-tunnel-protocol IPSec split-tunnel-policy tunnelspecified split-tunnel-network-list value YeahRightFLVPNTunnel_splitTunnelAcl default-domain value yeahright.com tunnel-group YeahRightFLVPN type remote-access tunnel-group YeahRightFLVPN general-attributes address-pool VPNPool tunnel-group YeahRightFLVPNTunnel type remote-access tunnel-group YeahRightFLVPNTunnel general-attributes address-pool VPNPool authentication-server-group WinRadius default-group-policy YeahRightFLVPNTunnel tunnel-group YeahRightFLVPNTunnel ipsec-attributes pre-shared-key *

Read the article

SQL Server 08 Express error when connecting to localhost - "Timeout expired". Works with ::1 or 127.0.0.1

- by Adam A

EDIT New info: Navigating to localhost:1434 in Chrome gives me an "ERR_EMPTY_RESPONSE", while other ports give me an "Oops! This link appears to be broken". So it seems to binding ok there? So here's my setup so far: I've configured Windows Firewall to allow TCP on 1433 and UDP on 1434. I've set up SQL Server to use any IP on Port 1433 (using the SQL Server Configuration Manager). My hosts file contains the default entries ("127.0.0.1 localhost" and "::1 localhost"). I sometimes have a debug session of Visual Web Developer running a webserver, but it's on a specific port (localhost:5XXXX). What I've tried: I CAN ping localhost in a cmd prompt. I CAN connect to the database through SSMS if I specify 127.0.0.1 or ::1 as the server name. I CAN'T connect to the database through SSMS (or ADO.NET) if I specify localhost as the server name. I've tried both Windows and SQL Authentication The error I get is the standard Can't connect to localhost. Additional Information -- Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft Sql Server) Other considerations: Stopping the Visual Web Developer web server from the taskbar doesn't affect the sql problem. The SQL error log says that it's listening on some piped name url at start up (I don't see how this would affect localhost but not 127.0.0.1 though). I could probably just use 127.0.0.1 everywhere, but it scares me that localhost isn't working and I'd like to figure out why. I'm not much of a networking or sql server guy so I'm stuck. If you want me to try anything to help diagnose just put it in a comment and I'll give it a go. Netstat results: Setting SDK environment relative to C:\Program Files\Microsoft SDKs\Windows\v6.1 Targeting Windows Server 2008 x86 DEBUG C:\Program Files\Microsoft SDKs\Windows\v6.1netstat -ano | findstr 1434 UDP 0.0.0.0:1434 *:* 6868 UDP [::]:1434 *:* 6868 C:\Program Files\Microsoft SDKs\Windows\v6.1netstat -ano | findstr 1433 TCP 0.0.0.0:1433 0.0.0.0:0 LISTENING 2268 TCP 127.0.0.1:1433 127.0.0.1:50758 ESTABLISHED 2268 TCP 127.0.0.1:50758 127.0.0.1:1433 ESTABLISHED 5008 TCP [::]:1433 [::]:0 LISTENING 2268 TCP [::1]:1433 [::1]:51202 ESTABLISHED 2268 TCP [::1]:1433 [::1]:51616 ESTABLISHED 2268 TCP [::1]:51202 [::1]:1433 ESTABLISHED 5008 TCP [::1]:51616 [::1]:1433 ESTABLISHED 5008 C:\Program Files\Microsoft SDKs\Windows\v6.1 SQL Server Log File: In case it helps 2010-01-30 12:58:59.01 Server Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) 2010-01-30 12:58:59.01 Server (c) 2005 Microsoft Corporation. 2010-01-30 12:58:59.01 Server All rights reserved. 2010-01-30 12:58:59.01 Server Server process ID is 2268. 2010-01-30 12:58:59.01 Server System Manufacturer: 'Dell Inc.', System Model: 'Inspiron 1545'. 2010-01-30 12:58:59.01 Server Authentication mode is MIXED. 2010-01-30 12:58:59.02 Server Logging SQL Server messages in file 'c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\Log\ERRORLOG'. 2010-01-30 12:58:59.02 Server This instance of SQL Server last reported using a process ID of 7396 at 1/30/2010 12:57:38 PM (local) 1/30/2010 5:57:38 PM (UTC). This is an informational message only; no user action is required. 2010-01-30 12:58:59.02 Server Registry startup parameters: -d c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\DATA\master.mdf -e c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\Log\ERRORLOG -l c:\Program Files\Microsoft SQL Server\MSSQL10.SQLEXPRESS\MSSQL\DATA\mastlog.ldf 2010-01-30 12:58:59.02 Server SQL Server is starting at normal priority base (=7). This is an informational message only. No user action is required. 2010-01-30 12:58:59.02 Server Detected 2 CPUs. This is an informational message; no user action is required. 2010-01-30 12:58:59.08 Server Using dynamic lock allocation. Initial allocation of 2500 Lock blocks and 5000 Lock Owner blocks per node. This is an informational message only. No user action is required. 2010-01-30 12:58:59.17 Server Node configuration: node 0: CPU mask: 0x00000003 Active CPU mask: 0x00000003. This message provides a description of the NUMA configuration for this computer. This is an informational message only. No user action is required. 2010-01-30 12:58:59.30 spid7s Starting up database 'master'. 2010-01-30 12:58:59.41 spid7s Recovery is writing a checkpoint in database 'master' (1). This is an informational message only. No user action is required. 2010-01-30 12:58:59.67 spid7s FILESTREAM: effective level = 0, configured level = 0, file system access share name = 'SQLEXPRESS'. 2010-01-30 12:58:59.92 spid7s SQL Trace ID 1 was started by login "sa". 2010-01-30 12:58:59.94 spid7s Starting up database 'mssqlsystemresource'. 2010-01-30 12:58:59.95 spid7s The resource database build version is 10.00.2531. This is an informational message only. No user action is required. 2010-01-30 12:59:00.82 spid7s Server name is 'DELL\SQLEXPRESS'. This is an informational message only. No user action is required. 2010-01-30 12:59:00.83 Server A self-generated certificate was successfully loaded for encryption. 2010-01-30 12:59:00.84 Server Server is listening on [ 'any' 1433]. 2010-01-30 12:59:00.84 Server Server is listening on [ 'any' 1433]. 2010-01-30 12:59:00.84 spid10s Starting up database 'model'. 2010-01-30 12:59:00.85 Server Server local connection provider is ready to accept connection on [ \\.\pipe\SQLLocal\SQLEXPRESS ]. 2010-01-30 12:59:00.86 Server Server local connection provider is ready to accept connection on [ \\.\pipe\MSSQL$SQLEXPRESS\sql\query ]. 2010-01-30 12:59:00.86 Server Dedicated administrator connection support was not started because it is disabled on this edition of SQL Server. If you want to use a dedicated administrator connection, restart SQL Server using the trace flag 7806. This is an informational message only. No user action is required. 2010-01-30 12:59:00.87 Server The SQL Server Network Interface library could not register the Service Principal Name (SPN) for the SQL Server service. Error: 0x54b, state: 3. Failure to register an SPN may cause integrated authentication to fall back to NTLM instead of Kerberos. This is an informational message. Further action is only required if Kerberos authentication is required by authentication policies. 2010-01-30 12:59:00.87 spid7s Informational: No full-text supported languages found. 2010-01-30 12:59:00.87 Server SQL Server is now ready for client connections. This is an informational message; no user action is required. 2010-01-30 12:59:00.91 spid7s Starting up database 'msdb'. 2010-01-30 12:59:01.21 spid10s Clearing tempdb database. 2010-01-30 12:59:02.78 spid10s Starting up database 'tempdb'. 2010-01-30 12:59:03.30 spid13s The Service Broker protocol transport is disabled or not configured. 2010-01-30 12:59:03.30 spid13s The Database Mirroring protocol transport is disabled or not configured. 2010-01-30 12:59:03.31 spid7s Recovery is complete. This is an informational message only. No user action is required. 2010-01-30 12:59:03.31 spid13s Service Broker manager has started.

Read the article

IP6tables blocks INPUT? can't connect with youtube API

- by klaas

I thought to have a simple ipv6 firewall, but it turned out to be hell. Somehow I really can't connect with any ipv6 from my machine unless I set INPUT Policy to ACCEPT. Below my current ip6tables ip6tables -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all anywhere anywhere state RELATED,ESTABLISHED ACCEPT ipv6-icmp anywhere anywhere ACCEPT tcp anywhere anywhere tcp dpt:http ACCEPT tcp anywhere anywhere tcp dpt:https Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination If I try to connect with any ipv6 adres it doesn't work? telnet gdata.youtube.com 80 Trying 2a00:1450:4013:c00::76... OR telnet gdata.youtube.com 443 Trying 2a00:1450:4013:c00::76... When I set: ip6tables -P INPUT ACCEPT It works.. but then.. well then everything is open? what is going on? Help?

Read the article

Linux Kernel Packet Forwarding Performance

- by Bob Somers

I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

Read the article

OpenBSD configuration: Client unable to mount via NFS using Berkeley Automounter (amd)

- by Rilindo

What I am trying to do is to have my openBSD client (OpenBSD 4.9) auto mount a Linux NFS file system (Scientific Linux 6.1). So far, I am not sure if it is configured correctly. To get things out of the way, I am able to mount nfs manually: # mount_nfs -T -3 192.168.15.100:/exports /mnt # ls -la /mnt total 52 drwxr-xr-x 7 root wheel 4096 Oct 4 22:42 . drwxr-xr-x 16 root wheel 512 Nov 26 16:33 .. drwxrwxr-x 5 _sndio _sndio 4096 Oct 31 21:58 centos drwxr-xr-x 15 root wheel 4096 Nov 6 09:17 home drwxr-xr-x 5 root wheel 4096 Oct 31 21:27 sl drwxr-xr-x 3 root wheel 4096 Nov 19 16:02 sles drwxr-xr-x 17 503 503 4096 Nov 10 17:37 users # So connectivity is not an issue, as far as I can tell. As per man page, the following is configured in /etc/amd/auto.home: /defaults type:=nfs;sublink:=${key};opts:=rw,soft,intr,vers=3,proto=tcp * rhost:=192.168.15.100;rfs:=/exports In turn, /etc/amd/master is configured as such: # cat /etc/amd/master /exports amd.home Upon reboot, I can it see mount, but curiously enough, instead of the hostname: amd:24490 0 0 0 100% /exports From what I understand, amd acts a little different from FreeBSD. Still, I tried to see if I it can automount. Nope: ksh: cd: /exports/users - Resource temporarily unavailable # cd /exports/192.168.15.100/host/users ksh: cd: /exports/192.168.15.100/host/users - Resource temporarily unavailable A search in google doesn't help too much - it seems that automounting NFS with OpenBSD is not something that is usually done. Other than this, information is fairly sparse. I can, of course, always mount is permanently, but I tend to be a bit anal on convention, so no for now. :) Some direction would be appreciation. (And oh, in case you are a wondering, I tried FreeBSD way of using amd and that hasn't worked out - although I wouldn't mind an explanation of the difference between how FreeBSD implements and how OpenBSD implements it) UPDATE: After re-writing the map file several times, I got as far as actually communicating with the NFS server with this configuration: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,tcp,resvport However, for some reason, it seems that amd will only default to NFS version 2 over udp: # tcpdump dst kerberos tcpdump: listening on pcn0, link-type EN10MB tcpdump: WARNING: compensating for unaligned libpcap packets 20:38:28.558385 openbsd.monzell.com.856 > kerberos.monzell.com.sunrpc: udp 100 20:38:28.559154 openbsd.monzell.com.856 > kerberos.monzell.com.892: udp 96 20:38:30.592761 openbsd.monzell.com.856 > kerberos.monzell.com.nfsd: xid 0x22000000 (NFSv2) 40 null 20:38:33.558107 arp reply openbsd.monzell.com is-at 52:54:00:52:8f:66 I tried various options of forcing it to try to mount as nfsv3 such as: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport or: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,vers=-3,proto=tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport Nothing yet still. Curious enough, OpenBSD mounts defaults to version 3, so I am not sure why it would start with version in amd. What would be the correct options to pass?

Read the article

Virtual Network Interface and NAT disables localhost access for MySQL and Apache

- by Interarticle

I'm running an Ubuntu Server 12.04, and recently I configured it to do NAT for my laptop. Since the server has only one NIC, I followed instructions online to create a virtual network device (eth0:0) that has a LAN IP address, then further configured iptables and UFW to allow internet sharing. However, just a few days ago, I discovered that one of the PHP pages hosted on the server failed for no apparent reason. A little digging revealed that the MySQL server started refusing connections from localhost. The same happened with a page (PhpMyAdmin) that was configured to be accessible only from localhost (in Apache2). The error, as shown by $mysql --protocol=tcp -u root -p looks like ERROR 1130 (HY000): Host '<host name of eth0>' is not allowed to connect to this MySQL server However, the funny thing is, I configured the mysql server to allow root access from localhost (only). Moreover, the mysql server listens only on 127.0.0.1:3306, as shown by: sudo netstat -npa | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 1029/mysqld which means that the connection could have only come from 127.0.0.1 (Note that MySQL is working because I can still connect to it via unix domain sockets) In effect, it seems that all tcp connections originating from 127.0.0.1 to 127.0.0.1 appear to any local daemon to come from the eth0 IP address. Indeed, apache2 allowed me to access PhpMyAdmin after I added allow <eth0 IP address>. The following are my network configurations (redacted): /etc/hosts: 127.0.0.1 localhost 211.x.x.x <host name of eth0> <server name> #IPv6 Defaults follows .... /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 211.x.x.x netmask 255.255.255.0 gateway 211.x.x.x dns-nameservers 8.8.8.8 # dns-* options are implemented by the resolvconf package, if installed dns-search xxxxxxx.com hwaddress ether xx:xx:xx:xx:xx:xx auto eth0:0 iface eth0:0 inet static address 192.168.57.254 netmask 255.255.254.0 broadcast 192.168.57.255 network 192.168.57.0 /etc/ufw/sysctl.conf: #Uncommented the following lines net/ipv4/ip_forward=1 net/ipv6/conf/default/forwarding=1 /etc/default/ufw: DEFAULT_FORWARD_POLICY="ACCEPT" #Changed DROP to ACCEPT /etc/init/internet-sharing.conf (upstart script I wrote), section pre-start script: iptables -A FORWARD -o eth0 -i eth0:0 -s 192.168.57.22 -m conntrack --ctstate NEW -j ACCEPT iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE Note again that my problem here is that programs cannot access localhost tcp services, from the server itself, and that access is blocked because the services have access control allowing only 127.0.0.1. I have no problem connecting (as in TCP connections) to services via tcp, even if the services listen only on 127.0.0.1. I do NOT want to connect to the services from another computer.

Read the article

wireshark does not show any http traffic

- by hayat

fMy pc is running windows XP. I have been trying to capture http traffic but if apply following filters, the wireshark gives results not required http result: it only show ssdp traffic http (!udp) result: it does not show any thing http (!http contains ssdp) result: it does not show any thing http && tcp result: it does not show any thing http (!udp.dstport == 1900) result: it does not show any thing tcp result: it shows tcp traffic but i cannot reach to my required http messages please guide what may be the problem, as the same thing is happening when i run it on a different OS (windows7) on my laptop

Read the article

OpenBSD configuration: Client unable to automount via NFS using amd

- by Rilindo

What I am trying to do is to have my openBSD client (OpenBSD 4.9) auto mount a Linux NFS file system (Scientific Linux 6.1). So far, I am not sure if it is configured correctly. To get things out of the way, I am able to mount nfs manually: # mount_nfs -T -3 192.168.15.100:/exports /mnt # ls -la /mnt total 52 drwxr-xr-x 7 root wheel 4096 Oct 4 22:42 . drwxr-xr-x 16 root wheel 512 Nov 26 16:33 .. drwxrwxr-x 5 _sndio _sndio 4096 Oct 31 21:58 centos drwxr-xr-x 15 root wheel 4096 Nov 6 09:17 home drwxr-xr-x 5 root wheel 4096 Oct 31 21:27 sl drwxr-xr-x 3 root wheel 4096 Nov 19 16:02 sles drwxr-xr-x 17 503 503 4096 Nov 10 17:37 users # So connectivity is not an issue, as far as I can tell. As per man page, the following is configured in /etc/amd/auto.home: /defaults type:=nfs;sublink:=${key};opts:=rw,soft,intr,vers=3,proto=tcp * rhost:=192.168.15.100;rfs:=/exports In turn, /etc/amd/master is configured as such: # cat /etc/amd/master /exports amd.home Upon reboot, I can it see mount, but curiously enough, instead of the hostname: amd:24490 0 0 0 100% /exports From what I understand, amd acts a little different from FreeBSD. Still, I tried to see if I it can automount. Nope: ksh: cd: /exports/users - Resource temporarily unavailable # cd /exports/192.168.15.100/host/users ksh: cd: /exports/192.168.15.100/host/users - Resource temporarily unavailable A search in google doesn't help too much - it seems that automounting NFS with OpenBSD is not something that is usually done. Other than this, information is fairly sparse. I can, of course, always mount is permanently, but I tend to be a bit anal on convention, so no for now. :) Some direction would be appreciation. (And oh, in case you are a wondering, I tried FreeBSD way of using amd and that hasn't worked out - although I wouldn't mind an explanation of the difference between how FreeBSD implements and how OpenBSD implements it) UPDATE: After re-writing the map file several times, I got as far as actually communicating with the NFS server with this configuration: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,tcp,resvport However, for some reason, it seems that amd will only default to NFS version 2 over udp: # tcpdump dst kerberos tcpdump: listening on pcn0, link-type EN10MB tcpdump: WARNING: compensating for unaligned libpcap packets 20:38:28.558385 openbsd.monzell.com.856 > kerberos.monzell.com.sunrpc: udp 100 20:38:28.559154 openbsd.monzell.com.856 > kerberos.monzell.com.892: udp 96 20:38:30.592761 openbsd.monzell.com.856 > kerberos.monzell.com.nfsd: xid 0x22000000 (NFSv2) 40 null 20:38:33.558107 arp reply openbsd.monzell.com is-at 52:54:00:52:8f:66 I tried various options of forcing it to try to mount as nfsv3 such as: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport or: /defaults type:=nfs;rhost:=kerberos.monzell.com;rfs:=/exports;\ sublink:=${key};opts:=rw,nodev,nosuid,soft,intr,vers=-3,proto=tcp,resvport * ${host}==${rhost};type:=nfs;fs:=${rfs};opts:=rw,nodev,nosuid,soft,intr,vers=3,proto=tcp,resvport Nothing yet still. Curious enough, OpenBSD mounts defaults to version 3, so I am not sure why it would start with version in amd. What would be the correct options to pass?

Read the article

Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

- by David Brown

Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

Read the article

Varnish "FetchError no backend connection" error

- by clueless-anon

Varnishlog: 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1340829925 1.0 12 SessionOpen c 79.124.74.11 3063 :80 12 SessionClose c EOF 12 StatSess c 79.124.74.11 3063 0 1 0 0 0 0 0 0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1340829928 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1340829931 1.0 12 SessionOpen c 108.62.115.226 46211 :80 12 ReqStart c 108.62.115.226 46211 467185881 12 RxRequest c GET 12 RxURL c / 12 RxProtocol c HTTP/1.0 12 RxHeader c User-Agent: Pingdom.com_bot_version_1.4_(http://www.pingdom.com/) 12 RxHeader c Host: www.mysite.com 12 VCL_call c recv lookup 12 VCL_call c hash 12 Hash c / 12 Hash c www.mysite.com 12 VCL_return c hash 12 VCL_call c miss fetch 12 FetchError c no backend connection 12 VCL_call c error deliver 12 VCL_call c deliver deliver 12 TxProtocol c HTTP/1.1 12 TxStatus c 503 12 TxResponse c Service Unavailable 12 TxHeader c Server: Varnish 12 TxHeader c Content-Type: text/html; charset=utf-8 12 TxHeader c Retry-After: 5 12 TxHeader c Content-Length: 418 12 TxHeader c Accept-Ranges: bytes 12 TxHeader c Date: Wed, 27 Jun 2012 20:45:31 GMT 12 TxHeader c X-Varnish: 467185881 12 TxHeader c Age: 1 12 TxHeader c Via: 1.1 varnish 12 TxHeader c Connection: close 12 Length c 418 12 ReqEnd c 467185881 1340829931.192433119 1340829931.891024113 0.000051022 0.698516846 0.000074035 12 SessionClose c error 12 StatSess c 108.62.115.226 46211 1 1 1 0 0 0 256 418 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1340829934 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1340829937 1.0 netstat -tlnp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 3086/nginx tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 1915/varnishd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1279/sshd tcp 0 0 127.0.0.2:25 0.0.0.0:* LISTEN 3195/sendmail: MTA: tcp 0 0 127.0.0.2:6082 0.0.0.0:* LISTEN 1914/varnishd tcp 0 0 127.0.0.2:9000 0.0.0.0:* LISTEN 1317/php-fpm.conf) tcp 0 0 127.0.0.2:3306 0.0.0.0:* LISTEN 1192/mysqld tcp 0 0 127.0.0.2:587 0.0.0.0:* LISTEN 3195/sendmail: MTA: tcp 0 0 127.0.0.2:11211 0.0.0.0:* LISTEN 3072/memcached tcp6 0 0 :::8080 :::* LISTEN 3086/nginx tcp6 0 0 :::80 :::* LISTEN 1915/varnishd tcp6 0 0 :::22 :::* LISTEN 1279/sshd /etc/nginx/site-enabled/default server { listen 8080; ## listen for ipv4; this line is default and implied listen [::]:8080 default ipv6only=on; ## listen for ipv6 root /usr/share/nginx/www; index index.html index.htm index.php; # Make site accessible from http://localhost/ server_name localhost; location / { # First attempt to serve request as file, then # as directory, then fall back to index.html try_files $uri $uri/ /index.html; } location /doc { root /usr/share; autoindex on; allow 127.0.0.2; deny all; } location /images { root /usr/share; autoindex off; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /usr/share/nginx/www; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.2:9000; fastcgi_index index.php; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # #location ~ /\.ht { # deny all; #} } /etc/nginx/sites-enabled/www.mysite.com.vhost server { listen 8080; server_name www.mysite.com mysite.com.net; root /var/www/www.mysite.com/web; if ($http_host != "www.mysite.com") { rewrite ^ http://www.mysite.com$request_uri permanent; } index index.php index.html; location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } # Deny all attempts to access hidden files such as .htaccess, .htpasswd, .DS_Store (Mac). location ~ /\. { deny all; access_log off; log_not_found off; } location / { try_files $uri $uri/ /index.php?$args; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; location ~* \.(jpg|jpeg|png|gif|css|js|ico)$ { expires max; log_not_found off; } location ~ \.php$ { try_files $uri =404; include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.2:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } include /var/www/www.mysite.com/web/nginx.conf; location ~ /nginx.conf { deny all; access_log off; log_not_found off; } } /etc/varnish/default.vcl # This is a basic VCL configuration file for varnish. See the vcl(7) # man page for details on VCL syntax and semantics. # # Default backend definition. Set this to point to your content # server. # backend default { .host = "127.0.0.2"; .port = "8080"; # .connect_timeout = 600s; #.first_byte_timeout = 600s; # .between_bytes_timeout = 600s; # .max_connections = 800; Note: uncommenting the last four options at default.vcl made no difference. cat /etc/default/varnish # Configuration file for varnish # # /etc/init.d/varnish expects the variables $DAEMON_OPTS, $NFILES and $MEMLOCK # to be set from this shell script fragment. # # Should we start varnishd at boot? Set to "yes" to enable. START=yes # Maximum number of open files (for ulimit -n) NFILES=131072 # Maximum locked memory size (for ulimit -l) # Used for locking the shared memory log in memory. If you increase log size, # you need to increase this number as well MEMLOCK=82000 # Default varnish instance name is the local nodename. Can be overridden with # the -n switch, to have more instances on a single server. INSTANCE=$(uname -n) # This file contains 4 alternatives, please use only one. ## Alternative 1, Minimal configuration, no VCL # # Listen on port 6081, administration on localhost:6082, and forward to # content server on localhost:8080. Use a 1GB fixed-size cache file. # # DAEMON_OPTS="-a :6081 \ # -T localhost:6082 \ # -b localhost:8080 \ # -u varnish -g varnish \ # -S /etc/varnish/secret \ # -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" ## Alternative 2, Configuration with VCL # # Listen on port 6081, administration on localhost:6082, and forward to # one content server selected by the vcl file, based on the request. Use a 1GB # fixed-size cache file. # DAEMON_OPTS="-a :80 \ -T 127.0.0.2:6082 \ -f /etc/varnish/default.vcl \ -S /etc/varnish/secret \ -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" If you need any other info let me know. I am all out of clue as to whats the problem.

Read the article

JBOSS 7.1 started hanging after 6 months of deployment

- by PVR

My application is been live from 6 months. The application is host on jboss 7.1 server. From last few days I am finding numerous problem of hanging of jboss server. Though I restart the jboss server again, it does not invoke. I need to restart the server machine itself. Can anyone please let me know what could be the cause of these problems and the workable resolutions or any suggestion ? Kindly dont degrade the question as I am facing a lot problems due to this hanging issue. Also for the information, the application is based on Java, GWT, Hibernate 3. Please find the standalone.xml file in case if it helps. <extensions> <extension module="org.jboss.as.clustering.infinispan"/> <extension module="org.jboss.as.configadmin"/> <extension module="org.jboss.as.connector"/> <extension module="org.jboss.as.deployment-scanner"/> <extension module="org.jboss.as.ee"/> <extension module="org.jboss.as.ejb3"/> <extension module="org.jboss.as.jaxrs"/> <extension module="org.jboss.as.jdr"/> <extension module="org.jboss.as.jmx"/> <extension module="org.jboss.as.jpa"/> <extension module="org.jboss.as.logging"/> <extension module="org.jboss.as.mail"/> <extension module="org.jboss.as.naming"/> <extension module="org.jboss.as.osgi"/> <extension module="org.jboss.as.pojo"/> <extension module="org.jboss.as.remoting"/> <extension module="org.jboss.as.sar"/> <extension module="org.jboss.as.security"/> <extension module="org.jboss.as.threads"/> <extension module="org.jboss.as.transactions"/> <extension module="org.jboss.as.web"/> <extension module="org.jboss.as.webservices"/> <extension module="org.jboss.as.weld"/> </extensions> <system-properties> <property name="org.apache.coyote.http11.Http11Protocol.COMPRESSION" value="on"/> <property name="org.apache.coyote.http11.Http11Protocol.COMPRESSION_MIME_TYPES" value="text/javascript,text/css,text/html,text/xml,text/json"/> </system-properties> <management> <security-realms> <security-realm name="ManagementRealm"> <authentication> <properties path="mgmt-users.properties" relative-to="jboss.server.config.dir"/> </authentication> </security-realm> <security-realm name="ApplicationRealm"> <authentication> <properties path="application-users.properties" relative-to="jboss.server.config.dir"/> </authentication> </security-realm> </security-realms> <management-interfaces> <native-interface security-realm="ManagementRealm"> <socket-binding native="management-native"/> </native-interface> <http-interface security-realm="ManagementRealm"> <socket-binding http="management-http"/> </http-interface> </management-interfaces> </management> <profile> <subsystem xmlns="urn:jboss:domain:logging:1.1"> <console-handler name="CONSOLE"> <level name="INFO"/> <formatter> <pattern-formatter pattern="%d{HH:mm:ss,SSS} %-5p [%c] (%t) %s%E%n"/> </formatter> </console-handler> <periodic-rotating-file-handler name="FILE"> <formatter> <pattern-formatter pattern="%d{HH:mm:ss,SSS} %-5p [%c] (%t) %s%E%n"/> </formatter> <file relative-to="jboss.server.log.dir" path="server.log"/> <suffix value=".yyyy-MM-dd"/> <append value="true"/> </periodic-rotating-file-handler> <logger category="com.arjuna"> <level name="WARN"/> </logger> <logger category="org.apache.tomcat.util.modeler"> <level name="WARN"/> </logger> <logger category="sun.rmi"> <level name="WARN"/> </logger> <logger category="jacorb"> <level name="WARN"/> </logger> <logger category="jacorb.config"> <level name="ERROR"/> </logger> <root-logger> <level name="INFO"/> <handlers> <handler name="CONSOLE"/> <handler name="FILE"/> </handlers> </root-logger> </subsystem> <subsystem xmlns="urn:jboss:domain:configadmin:1.0"/> <subsystem xmlns="urn:jboss:domain:datasources:1.0"> <datasources> <datasource jndi-name="java:jboss/datasources/ExampleDS" pool-name="ExampleDS" enabled="true" use-java-context="true"> <connection-url>jdbc:h2:mem:test;DB_CLOSE_DELAY=-1</connection-url> <driver>h2</driver> <security> <user-name>sa</user-name> <password>sa</password> </security> </datasource> <drivers> <driver name="h2" module="com.h2database.h2"> <xa-datasource-class>org.h2.jdbcx.JdbcDataSource</xa-datasource-class> </driver> </drivers> </datasources> </subsystem> <subsystem xmlns="urn:jboss:domain:deployment-scanner:1.1"> <deployment-scanner path="deployments" relative-to="jboss.server.base.dir" scan-interval="5000"/> </subsystem> <subsystem xmlns="urn:jboss:domain:ee:1.0"/> <subsystem xmlns="urn:jboss:domain:ejb3:1.2"> <session-bean> <stateless> <bean-instance-pool-ref pool-name="slsb-strict-max-pool"/> </stateless> <stateful default-access-timeout="5000" cache-ref="simple"/> <singleton default-access-timeout="5000"/> </session-bean> <pools> <bean-instance-pools> <strict-max-pool name="slsb-strict-max-pool" max-pool-size="20" instance-acquisition-timeout="5" instance-acquisition-timeout-unit="MINUTES"/> <strict-max-pool name="mdb-strict-max-pool" max-pool-size="20" instance-acquisition-timeout="5" instance-acquisition-timeout-unit="MINUTES"/> </bean-instance-pools> </pools> <caches> <cache name="simple" aliases="NoPassivationCache"/> <cache name="passivating" passivation-store-ref="file" aliases="SimpleStatefulCache"/> </caches> <passivation-stores> <file-passivation-store name="file"/> </passivation-stores> <async thread-pool-name="default"/> <timer-service thread-pool-name="default"> <data-store path="timer-service-data" relative-to="jboss.server.data.dir"/> </timer-service> <remote connector-ref="remoting-connector" thread-pool-name="default"/> <thread-pools> <thread-pool name="default"> <max-threads count="10"/> <keepalive-time time="100" unit="milliseconds"/> </thread-pool> </thread-pools> </subsystem> <subsystem xmlns="urn:jboss:domain:infinispan:1.2" default-cache-container="hibernate"> <cache-container name="hibernate" default-cache="local-query"> <local-cache name="entity"> <transaction mode="NON_XA"/> <eviction strategy="LRU" max-entries="10000"/> <expiration max-idle="100000"/> </local-cache> <local-cache name="local-query"> <transaction mode="NONE"/> <eviction strategy="LRU" max-entries="10000"/> <expiration max-idle="100000"/> </local-cache> <local-cache name="timestamps"> <transaction mode="NONE"/> <eviction strategy="NONE"/> </local-cache> </cache-container> </subsystem> <subsystem xmlns="urn:jboss:domain:jaxrs:1.0"/> <subsystem xmlns="urn:jboss:domain:jca:1.1"> <archive-validation enabled="true" fail-on-error="true" fail-on-warn="false"/> <bean-validation enabled="true"/> <default-workmanager> <short-running-threads> <core-threads count="50"/> <queue-length count="50"/> <max-threads count="50"/> <keepalive-time time="10" unit="seconds"/> </short-running-threads> <long-running-threads> <core-threads count="50"/> <queue-length count="50"/> <max-threads count="50"/> <keepalive-time time="100" unit="seconds"/> </long-running-threads> </default-workmanager> <cached-connection-manager/> </subsystem> <subsystem xmlns="urn:jboss:domain:jdr:1.0"/> <subsystem xmlns="urn:jboss:domain:jmx:1.1"> <show-model value="true"/> <remoting-connector/> </subsystem> <subsystem xmlns="urn:jboss:domain:jpa:1.0"> <jpa default-datasource=""/> </subsystem> <subsystem xmlns="urn:jboss:domain:mail:1.0"> <mail-session jndi-name="java:jboss/mail/Default"> <smtp-server outbound-socket-binding-ref="mail-smtp"/> </mail-session> </subsystem> <subsystem xmlns="urn:jboss:domain:naming:1.1"/> <subsystem xmlns="urn:jboss:domain:osgi:1.2" activation="lazy"> <properties> <property name="org.osgi.framework.startlevel.beginning"> 1 </property> </properties> <capabilities> <capability name="javax.servlet.api:v25"/> <capability name="javax.transaction.api"/> <capability name="org.apache.felix.log" startlevel="1"/> <capability name="org.jboss.osgi.logging" startlevel="1"/> <capability name="org.apache.felix.configadmin" startlevel="1"/> <capability name="org.jboss.as.osgi.configadmin" startlevel="1"/> </capabilities> </subsystem> <subsystem xmlns="urn:jboss:domain:pojo:1.0"/> <subsystem xmlns="urn:jboss:domain:remoting:1.1"> <connector name="remoting-connector" socket-binding="remoting" security-realm="ApplicationRealm"/> </subsystem> <subsystem xmlns="urn:jboss:domain:resource-adapters:1.0"/> <subsystem xmlns="urn:jboss:domain:sar:1.0"/> <subsystem xmlns="urn:jboss:domain:security:1.1"> <security-domains> <security-domain name="other" cache-type="default"> <authentication> <login-module code="Remoting" flag="optional"> <module-option name="password-stacking" value="useFirstPass"/> </login-module> <login-module code="RealmUsersRoles" flag="required"> <module-option name="usersProperties" value="${jboss.server.config.dir}/application-users.properties"/> <module-option name="rolesProperties" value="${jboss.server.config.dir}/application-roles.properties"/> <module-option name="realm" value="ApplicationRealm"/> <module-option name="password-stacking" value="useFirstPass"/> </login-module> </authentication> </security-domain> <security-domain name="jboss-web-policy" cache-type="default"> <authorization> <policy-module code="Delegating" flag="required"/> </authorization> </security-domain> <security-domain name="jboss-ejb-policy" cache-type="default"> <authorization> <policy-module code="Delegating" flag="required"/> </authorization> </security-domain> </security-domains> </subsystem> <subsystem xmlns="urn:jboss:domain:threads:1.1"/> <subsystem xmlns="urn:jboss:domain:transactions:1.1"> <core-environment> <process-id> <uuid/> </process-id> </core-environment> <recovery-environment socket-binding="txn-recovery-environment" status-socket-binding="txn-status-manager"/> <coordinator-environment default-timeout="300"/> </subsystem> <subsystem xmlns="urn:jboss:domain:web:1.1" default-virtual-server="default-host" native="false"> <connector name="http" protocol="HTTP/1.1" scheme="http" socket-binding="http"/> <virtual-server name="default-host" enable-welcome-root="false"> <alias name="localhost"/> <alias name="nextenders.com"/> </virtual-server> </subsystem> <subsystem xmlns="urn:jboss:domain:webservices:1.1"> <modify-wsdl-address>true</modify-wsdl-address> <wsdl-host>${jboss.bind.address:127.0.0.1}</wsdl-host> <endpoint-config name="Standard-Endpoint-Config"/> <endpoint-config name="Recording-Endpoint-Config"> <pre-handler-chain name="recording-handlers" protocol-bindings="##SOAP11_HTTP ##SOAP11_HTTP_MTOM ##SOAP12_HTTP ##SOAP12_HTTP_MTOM"> <handler name="RecordingHandler" class="org.jboss.ws.common.invocation.RecordingServerHandler"/> </pre-handler-chain> </endpoint-config> </subsystem> <subsystem xmlns="urn:jboss:domain:weld:1.0"/> </profile> <interfaces> <interface name="management"> <inet-address value="${jboss.bind.address.management:127.0.0.1}"/> </interface> <interface name="public"> <inet-address value="${jboss.bind.address:127.0.0.1}"/> </interface> <interface name="unsecure"> <inet-address value="${jboss.bind.address.unsecure:127.0.0.1}"/> </interface> </interfaces> <socket-binding-group name="standard-sockets" default-interface="public" port-offset="${jboss.socket.binding.port-offset:0}"> <socket-binding name="management-native" interface="management" port="${jboss.management.native.port:9999}"/> <socket-binding name="management-http" interface="management" port="${jboss.management.http.port:9990}"/> <socket-binding name="management-https" interface="management" port="${jboss.management.https.port:9443}"/> <socket-binding name="ajp" port="8009"/> <socket-binding name="http" port="80"/> <socket-binding name="https" port="443"/> <socket-binding name="osgi-http" interface="management" port="8090"/> <socket-binding name="remoting" port="4447"/> <socket-binding name="txn-recovery-environment" port="4712"/> <socket-binding name="txn-status-manager" port="4713"/> <outbound-socket-binding name="mail-smtp"> <remote-destination host="localhost" port="25"/> </outbound-socket-binding> </socket-binding-group>

Read the article

Block Google requests to 16k using pf firewall

- by atmosx

I'd like to block access to Google search using PF after the threshold of 17500 requests (connection established) in 24h, from a host running FreeBSD 9. What I came up with, after reading pf-faq is this rule: pass out on $net proto tcp from any to 'www.google.com' port www flags S/SA keep state (max-src-conn 200, max-src-conn-rate 17500/86400) NOTE: 86400 are 24h in seconds. The rule should work, but PF is smart enough to know that www.google.com resolves in 5 different IPs. So my pfctl -sr output gives me this: pass out on vte0 inet proto tcp from any to 173.194.44.81 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.82 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.83 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.80 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) pass out on vte0 inet proto tcp from any to 173.194.44.84 port = http flags S/SA keep state (source-track rule, max-src-conn 200, max-src-conn-rate 17500/86400, src.track 86400) PF creates 5 different rules, 1 for each IP that Google resolves. However I have the sense - without being 100% sure, I didn't had the chance to test it - that the number 17500/86400 applies for each IP. If that's the case - please confirm - then it's not what I want. In pf-faq there's another option called source-track-global: source-track This option enables the tracking of number of states created per source IP address. This option has two formats: + source-track rule - The maximum number of states created by this rule is limited by the rule's max-src-nodes and max-src-states options. Only state entries created by this particular rule count toward the rule's limits. + source-track global - The number of states created by all rules that use this option is limited. Each rule can specify different max-src-nodes and max-src-states options, however state entries created by any participating rule count towards each individual rule's limits. The total number of source IP addresses tracked globally can be controlled via the src-nodes runtime option. I tried to apply source-track-global in the above rule without success. How can I use this option in order to achieve my goal? Any thoughts or comments are more than welcome since I'm an amateur and don't fully understand PF yet. Thanks

Search Results

Search found 12283 results on 492 pages for 'tcp port'.

Page 121/492 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128 | Next Page >

- by piobyz

- by Johan Nielsen

- by Joan H.

- by BGM

- by Logan Bissonnette

- by Kstro21

- by JohnMerlino

- by Eyla

- by Andy Shinn

- by id.roppert.dejroppert

- by Miguel

- by Selivanov Pavel

- by Adam A

- by user50855

- by Adam A

- by klaas

- by Bob Somers

- by Rilindo

- by Interarticle

- by hayat

- by Rilindo

- by David Brown

- by clueless-anon

- by PVR

- by atmosx

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128 | Next Page >