Search Results

Search found 6346 results on 254 pages for 'turn a'.

Page 122/254 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• Network based on Netgear FVS318 extremely slow

  - by Fentible

  A network I maintain uses an FVS318 as a router, with a separate switch. Communication within the network is slow. Out to the internet is even slower. As it stands there is one patch from the FVS to the switch and no other devices directly connected to the FVS because any that are run so slowly they might as well not be connected to the network. Swapping in a bog-standard home router dramatically increases network speed, but that's not a viable solution because some of the enterprise features of the FVS are required. There are quite a few complaints about this on the Netgear forum, but Netgear support have not been forthcoming with any help - so I turn to you all: any ideas?

  Read the article

• Firestarted Blocking DHCP?

  - by Chiggins

  Alright so on my Ubuntu laptop I get a wireless internet signal, and then distribute it to a switch where my other computers are connected. I also have Firestarter installed on the laptop. I have a problem where the only way that one of my client computers try to get an IP and such from my laptop, it can't because Firestarter is blocking it somehow. I have to stop the firewall in Firestarter, then connect from a client. It connects right away, then I turn Firestarter back on. In the preferences there is an option in "Firewall" called "Start/restart firewall on DHCP lease", but if I have that checked or not doesn't make a difference. So, what can I do to fix this? Its kinda annoying to have to do this whenever I have to connect to the internet. Thanks!

  Read the article

• What protocols will/are ISPs use for IPv6 deployment?

  - by rbeede

  Currently ISPs deal out addresses via DHCP for IPv4 dynamic (single) addresses. What protocol will/are ISPs going to use for IPv6 when they can hand a customer an entire /64 (or /48 if they are nice) block? DHCPv6, RA? For ISPs that support true end-to-end IPv6 will they provide gateway devices (similar to cable modem or true DSL bridges for example) that receive border information for that specific customer? I'm just trying to get an idea of how your common residential service customer will have to configure things in an IPv6 Internet (whenever that comes). Will it be something customers are expected to statically configure on their home wireless router? Today with IPv4 I do it like this: Modem (bridge) passes public IPv4 obtained via DHCPv4 from ISP to second device (wireless router). It in turn has its own DHCPv4 service it provides on the internal lan.

  Read the article

• How to keep the Alt-Tab menu on the second monitor in Ubuntu?

  - by D Connors

  I'm running the latest Ubuntu version on my laptop, and every day when I arrive at my office I turn on the laptop and plug everything on. That includes a monitor that happens to be larger than the laptop's monitor. I always do my work on the desktop monitor, so I'd like for the Alt-Tab menu to always pop-up on this one. Instead, it's configured to pop-up whichever monitor the mouse is on (which makes sense, but doesn't work for me). Anybody know a way to change that?

  Read the article

• What is the cost of running a desktop machine at home?

  - by vinc

  How much does it (roughly) cost to leave my personal home computer running 24/7 for a year? I'm not doing anything unusual; I run a webserver for myself, surf the web, write some code. I don't have any specific specs. So for example there might be the cost of electricity, internet connection, and possibly some other factors that I've overlooked. I'm trying to decide whether it would be a good idea to turn off my computer when I'm asleep and not using it. Is the cost negligible, maybe 1 USD per day, something in between or more?

  Read the article

• How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• Is there a way to permanently remove highlighting from editable areas within a protected word docume

  - by CT

  Is there a way to permanently remove highlighting from editable areas within a protected word document? This is in relation to a previous question I had on locking portions of a Word Document located here: http://superuser.com/questions/143860/can-i-lock-or-make-uneditable-portions-of-a-word-document Using this solution, any editable area is highlighted. You can uncheck the Highlight editable area box within the Protect Document bar but if you save and reopen the area is highlighted again. The document is on a network drive. If another user were to open the document it would also be highlighted. Is there anyway to permanently turn this highlighting off so that when a user accesses the document from the network they do not see this highlighting? Using Word 2007.

  Read the article

• Is there anything essential to check before powering on a self-built PC for the first time?

  - by Nick F

  I've just put together a computer for the first time. I've found plenty of info online that covered the construction, but now I'm ready - I think - to power it up I'm wondering if there are any checks that I can do to be sure that the machine is safe and ready to turn on. What are the things (if any) that I absolutely must make sure of before turning on? Just to be clear, I'm sure there are many things I could get wrong that would mean the computer won't work properly, but only a few that might cause serious damage. It's really the latter I'm asking for.

  Read the article

• Skype prevents computer from idling?

  - by Corey Sarnia

  When using Skype, it prevents the computer from idling, going into sleep mode and turning the monitor off. I notice on my laptop if I use a tool like Monitor Off to manually turn my monitor off, after about a minute, the monitor will come back on as if Skype has pressed a key or moved my mouse to exit out of that idle state. This also prevents other programs (such as Pidgin) from going idle as well, so it looks like I'm online 24/7... even though it should be going idle after 5 minutes of inactivity. Is there a way to circumvent this behavior in Skype?

  Read the article

• Homegroup sharing problems

  - by soandos

  I can see other people in my homegroup and their folders, but when I click on those folders, I cannot see the contents (no error message, just nothing happens). The other people in the Homegroup can see me just fine, and my files In addition, I cannot see the files that they have under the network tab, though they can all see each others stuff. What could be the issue? The homegroup has already be created and recreated numerous times. Perhaps unrelated, but I am unable to turn off password protected sharing.

  Read the article

• How can I open a port in OS X 10.6?

  - by Ian

  Mine is MacBook Air, so I cannot plug to the modem directly. And I do want to turn my firewall off. How can I specify to open a port, like port 56789 in Mac OS 10.6.8? I know in old Mac OS, there is a option for me to specify a custom port. But I cannot find it in OS X 10.6.8. In System Preferences / Security / Firewall, I only can allow an APPLICATION to access a new port. However, now I'm programming, using a new port. So, it seems not suitable for me. So, can I simply open a port instead of using an Application to open a port?

  Read the article

• How can I prevent JungleDisk/MacOS X (10.6) creating a local volume for a removed external drive?

  - by Rew

  Ok, here is situation: I use JungleDisk to sync an online folder on to a external drive connected to my Mac. If I right click Finder, click Go to Folder... then type /Volumes/ I see the drive linked here. Once I remove the external drive, an actual folder is created here in the name of the external drive, JungleDisk continues to copy files to this folder, rather than stop. Is this a feature of Mac OS X? Can I turn if off? After I re-connect my external drive, the link to the drive is appended with a 1 (so if I called the drive SpareDrive it becomes SpareDrive 1 as the newly created folder is called SpareDrive. I realise my explanation isn't very clear, but anyone understand this, and knows how to prevent it happening please let me know. PS: I have a low reputation as I don't use this often, I tend to use stackoverflow, but will check back here for answers.

  Read the article

• Defrag/TRIM settings for hybrid hard drive?

  - by Joel Coehoorn

  I recently acquired a momentus XT hybrid hard drive. This is a tradition spinning HDD with a small SSD portion for frequently used files. Normally, you are not supposed to defrag SSDs, as it does not help performance and can significantly reduce the life of the drive. But you do need to defrag an HDD to keep good performance. So where does that leave us for hybrid drives? Do I need to turn off defragging in Windows to preserve the SSD portion? Is the on-disk controller smart enough to handle defragging correctly? Is there some utility I need to set it up that I missed? Additionally, for SSDs you normally want to check for and enable TRIM support... but this makes no sense for a HDDs. Where does that leave us for hybrid drives? Should I try to enable TRIM or not?

  Read the article

• Can Grub be configured to remember the last OS you booted into?

  - by Matthew

  I typically have 2-3 OSes in my boot menu: Ubuntu 10.04 Windows 7 [Sometimes, a third option, such as Ubuntu 10.04 Netbook] If I am in an OS other than the default choice (Windows 7 in this case), and I reboot, Grub boots into Ubuntu 10.04. This shouldn't happen--when I reboot in Windows 7, I want to stay in Windows 7. Is there any way to configure Grub to remember my last choice, and boot into that? Alternatively, it would be even better if Grub only did this when I rebooted (not when I first turn the computer on). I realize this may not be possible, so I'd be happy with simple last-choice-remembering.

  Read the article

• Computer temporarily freezes and then resumes

  - by trizicus

  This happens on ALL operating systems (7, Ubuntu, etc.). What happens is everything for 1-3 seconds becomes unresponsive, I then hear what sounds like my other internal hard drive 'spinning up', and then viola everything is responsive again. Note: Already ran SMART tests, no issues at all. I think issue is that the HDD spins down and when need it gets 'turned-on' (OS settings turn off HDD's after 20 mins of inactivity) and because my pagefile is on the other HDD it causes OS to temporarily freeze. Need more tips, and insight. Thanks More info: Running Quad CPU, 4GB RAM, Intel SSD, GT 240.

  Read the article

• Can't Remote into Windows Server

  - by Brian

  Hello, I have a Dell server wired into the router. I was able to connect to it with my laptop (laptop is wireless) before my router died. My verizon router went kaput, and I got everything else back up and running on the wireless network other than the remoting in feature, even though I can access the server through windows explorer just fine. Any ideas why? What do I need to check? UPDATE: Interesting scenario, Network Discovery is off; I turn it on and save, but for some reason, even after that, network discovery is turning itself off... no idea why that is happening? Thanks.

  Read the article

• Turning a (dual boot) Ubuntu 9 into a virtual machine

  - by xain

  I have a dual boot box (Ubuntu 9 and Vista) and I'm about to upgrade Vista to Win 7. Being Ubuntu my main development environment, I'd like to use it as it is from the new environment via VirtualBox or VMWare. I know tools like clonezilla that backup entire drives; in my case, the linux partitions are distributed between several disks which in turn contain both linux and windows data. My intention is to use some backup tool (like Clonezilla if it fits) that allows me to ONLY backup the linux partitions distributed in several disks. Any hints ? Thanks in advance.

  Read the article

• Motherboard or Processor Problem

  - by bradlis7

  My computer is broken, but I'm having trouble narrowing down the issue. I replaced the power supply, because I assumed that was the issue, but it has the same problem. The issue started with my computer starting the fans and running, but it didn't get to the BIOS screen for about 10 seconds. Now it refuses to do anything when the power button is pressed, except when I turn off the machine and take the processor out for 10-20 seconds, then put it back in, I came hit the power button immediately, and the fans start for 1/2 second, and quit. Does this sound like a is a processor or motherboard issue? I removed all components, so I know that the issue is with one of these two things.

  Read the article

• problem on expand network using a router

  - by Jose

  I have a Netgear FS605 v3 router, and i'm trying to expand my network. The router is connected to the cable modem with cat5 cable. I have 2 laptop connected to the router but i'm only able to get internet connectivity in one. The first laptop i turn on, get the signal and the other one will show no connectivity. I have restarted all the devices many times but no luck. Can somebody explain me how to get this solved. Thanks.

  Read the article

• Hide unauthorized folders from view in webdav

  - by eric.s

  We have a Windows server running webdav. When a Mac connects to it they see the folders they do not have access to as a blacked out folder, and then the folders they do have access to as folders. This does not happen when a client using Linux or Windows connects. All users connect with their domain account credentials. I may not be searching properly to get the information I am looking for, so I turn here. Is this an issue that I should be researching on the Mac side, or ask our network team to be looking into settings on the server?

  Read the article

• Hard disk failure. Can I recover my "move"d folders?

  - by Doug

  I am in the process of moving all my files from an old laptop to new one. I just moved 11gb of data from my old laptop to a hard drive (external) and then upon moving it out to the new hard drive, the hard drive is getting a CRC (Data Error (Cyclic Redundancy Check). Now I am looking for a solution to recover the files that I moved on my old laptop (not the external). I understand they they are just marked for potential overwriting to free up space. I was getting ready to test out GetDataBack, but it says to install it on a healthy windows and use the recover-needed drive as an external. However, I don't want to turn off my computer without first getting the okay since it is in a "moved" state. Please help! What can I do to recover the Moved files. I haven't touched the computer since it has been moved. What can I use to recover them?

  Read the article

• Lost current user (shutdown/logoff) widget after upgrading to Ubuntu 10.04

  - by xyzman

  I've upgraded to 10.04 from 9.10. Everything went fine until I've rebooted. After reboot, I've received some message about status panel and being sleepy, dismissed it. However, I haven't seen the user widget on Gnome Panel since that. This image shows which widget I'm talking about. If some one has any ideas about how it's called properly, please share. http://img237.imageshack.us/img237/8274/sampleyu.jpg Anyway, the question is, how do I turn this panel (and ability to shut my system down without resorting to console) back?

  Read the article

• From where can I get "Python Launcher" for Mac OS X Lion?

  - by Phil

  I use a macbook (air) with OS X Lion on it. I have Python 2.7 installed already but I can't seem to find a "Python Launcher.app" anywhere on the system. I tried installing with with pip but it couldn't find anything to fetch. I tried searching on Google to find a downloader but my search yielded no results (for downloading). Where can I get this app? I have a folder with 20+ subfolders of GUI examples which in turn contain anywhere from 3 to 5 subfolders. I don't want to go through each within the terminal, would much rather launch these .py scrips from the finder. Thank you for your help.

  Read the article

• Smoothwall: How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• Increase Volume of an MKV Video from Linux Terminal

  - by The How-To Geek

  I've got a large amount of .MKV video files which seem to all play at a very low volume - I end up having to turn the TV up all the way to hear them, which is really irritating when I switch to another channel and wake the dead because it's so loud. What I'm looking for is a command-line method to increase the volume (so I can run it on all of them quickly) that would hopefully work regardless of the audio codec in use in the particular file. (I don't mind hard-coding the output audio though). For reference, I'm using Ubuntu 9.04 on my server, and the files are being played back with Boxee on a Mac Mini, but the volume problem is the same on Windows too.

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >