Search Results

Search found 3985 results on 160 pages for 'hd dvd'.

Page 124/160 | < Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >

  • Ubuntu 12.04 installation on GPT + RAID going into grub rescue

    - by Proy
    I have two 2TB disks. I am installing Ubuntu 12.04 using the alternate version of the server cd. On the partitioning page I have done my partitioning as follows /dev/sda1 - 32 MB - bios_grub /dev/sda2 - 50 GB -raid device /dev/sda3 - 8 GB -raid device /dev/sda4 - Balance full GB - raid device /dev/sdb1 - 32 MB - bios_grub /dev/sdb2 - 50 GB -raid device /dev/sdb3 - 8 GB -raid device /dev/sdb4 - Balance full GB - raid device After this I have setup raid devices /dev/md0 for /(/dev/sda2 + /dev/sdb2) for / ext4 /dev/md1 for swap( /dev/sda3 + /dev/sdb3)for swap /dev/md2 for /home(/dev/sda4 + /dev/sdb4)for /home ext4 The installation finishes it shows that it is installing grub to /dev/sda and /dev/sdb. But once the system reboots it falls into grub rescue mode. on doing ls I can not see the md devices only hd once. I also tried booting into rescue mode with the install cd and doing grub-install /dev/sda and /dev/sdb. What am I doing wrong ? Why is grub2 not detecting the raid revices ? UPDATE: I just did the same steps with Ubuntu 10.04 and it worked perfectly fine. I wiped out the RAID and partitions and everything and did it from scratch. I think the issue is with Ubuntu 12.04 and the way it partitions 2 TB disks

    Read the article

  • Making a game with responsive resolution

    - by alexandervrs
    I am making a game, however I wish for it to be resolution agnostic. My target resolution i.e. where things look as intended is 1600 x 900. My ideas are: Make the HUD stay fixed to the sides no matter what resolution, use different size for HUD graphics under a certain resolution and another under a certain large one. Use large HD sprites/backgrounds which are a power of 2, so they scale nicely. Use the player's native resolution. Scale the game area (not the HUD) to fit (resulting zooming in some and cropping the game area sides if necessary for widescreen, no stretch), but always fill the screen. Have a min and max resolution limit for small and very large displays where you will just change the resolution(?) or scale up/down to fit. What I am a bit confused though is what math formula I would use to scale the game area correctly based on the resolution no matter the aspect ratio, fully fit in a square screen and with some clip to the sides for widescreen. Pseudocode would help as well. :)

    Read the article

  • Can't install Ubuntu, black screen after install

    - by Tyrone
    I tried several times, but wasn't able to make it work. I tried all recent types of Ubuntu but it didn't work. Then I tried acpi=off at the beginning of the installation. In this way I could finish the installation. But after the restart Ubuntu didn't work. Only a black screen appeared. Before that I tried it on the VirtualBox and it work. By the way my system is the following: (I use windows 7 currently) Processor AMD Athlon II P320 (2,1 GHz, second-level cache 2 ? 512 KB, HT 1600 MHz bus) Chipset AMD M880G + SB850 Memory Dual Channel, 3 GB DDR3-1066 Wide Screen 15.6 “high-definition (1366 ? 768) c LED-backlit, AU Optronics B156XW02 Video Card AMD Radeon HD 4250, from 336 MB video buffer in memory, support for DirectX 10.1 and UVD Sound system: HDA-codec IDT 92HD81B1X AMD HDMI Audio Hard drive WDC WD3200BEVT-75A23T0 (298 GB, 5400 RPM, SATA 2.0) Optical Drive: DVD ± RW Optiarc AD-7585H Communication tools Fast Ethernet (10/100 Mbit / c) Realtek RTL8102E/RTL8103E WiFi 802.11a/b/g Broadcom BCM4310 Bluetooth 2.1 + EDR Card reader Memory Card Reader 7-in-1 with support for SD / SDHC / MMC / MS / xD, and derivatives Interfaces / ports 3 USB 2.0 1 eSATA + USB 2.0 15-pin video connector VGA HDMI RJ-45 Ethernet 10/100 Mbit / c 2 analog mini-jack: a microphone / headphone jack for a Kensington lock slot AC adapter Battery Li-Ion 6-cell capacity of 4400 mA ? h (10,8, 48 W ? hr) AC power adapter 65 Watt Additional equipment integrated web-camera (1.3 mega pixels)

    Read the article

  • How to Get a Smartphone-Style Word Suggestion on Windows

    - by Zainul Franciscus
    Have you ever wished that you can type faster and better in Windows ? Then you’re in luck, because today we’ll show you how to get a smartphone’s word suggestion in Windows. To accomplish that, you need to install AI Type, a software that gives word suggestion when you write in Windows.  AI Type not only fulfils our gratification to have a smartphone-style word suggestion for Windows,  AI Type also improves our writings by suggesting word according to its context. It  will also try to match words according to the  probability in which other users may have used it. Installing AI Type is a breeze; Just download the installer from AI Type website, run the executable, fill in a registration form, and you’re all set to use AI Type for your daily writing. Once you’re done with the installation, AI Type appears on your system tray. Latest Features How-To Geek ETC Macs Don’t Make You Creative! So Why Do Artists Really Love Apple? MacX DVD Ripper Pro is Free for How-To Geek Readers (Time Limited!) HTG Explains: What’s a Solid State Drive and What Do I Need to Know? How to Get Amazing Color from Photos in Photoshop, GIMP, and Paint.NET Learn To Adjust Contrast Like a Pro in Photoshop, GIMP, and Paint.NET Have You Ever Wondered How Your Operating System Got Its Name? Sync Blocker Stops iTunes from Automatically Syncing The Journey to the Mystical Forest [Wallpaper] Trace Your Browser’s Roots on the Browser Family Tree [Infographic] Save Files Directly from Your Browser to the Cloud in Chrome and Iron The Steve Jobs Chronicles – Charlie and the Apple Factory [Video] Google Chrome Updates; Faster, Cleaner Menus, Encrypted Password Syncing, and More

    Read the article

  • What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?

    - by Denja
    Hi Linux Community, I find my self struggling with the ever slow and buggy windoze OS once again. It's Time to change with the Ubuntu 10.10 64bit as a really faster Operating System. My Hard Disk laptop as a RECOVERY and HP_TOOLS partition they are both Primary. I Have the System Recovery DVD for Windows 64bit should anything happen. Here's the layout I used with windows before: * (C:) Windows 7 system partition NTFS - 284,89GB (Primary,Boot,Pagefile,Dump) * HP_TOOLS system partition FAT32 - 99MB (Primary) * (D:) RECOVERY partition NTFS - 12,90GB (Primary) * SYSTEM partition NTFS 199MB (Primary) Here's the layout I want to make based on your answers * (C:) Windows 7 system partition NTFS - 60GB (Primary) (sda1) * (D:) Windows DATA partition (user files) NTFS - 120GB(Primary)(sda2);wanna share with Linux * Linux root Ext4 - 100GB (Primary)(sda3) (Ubuntu 10.10 64bit) * Linux swap swap- RAM size, 3GB (sda4) * Linux root Ext3- 15,9GB (Extended)(sda5) (OpenSuse or Puppy) Here is my New Ubuntu 10.10 64bit layout in use now: * SYSTEM partition NTFS 199MB (Primary) (sda1) **Partition 1 does not end on cylinder boundary.(?)** * (C:) Windows 7 system partition NTFS - 90GB (Primary) (sda2) * (D:) Windows 7 RECOVERY partition NTFS - 12,90GB (Primary) (sda3) * Linux system partition EXTENDED - 195GB (Logical) * Linux root Ext4- 10GB (Extended) (sda5) * Linux home Ext3- 185GB (Extended) (sda6) I didn't know if I could wipe all previous partitions when i installed Ubuntu because of the RECOVERY partition so I just made the space for my extended partition by deleting the HP_TOOLS (Fat32). By doing this I managed to make and successfully install Ubuntu 64 but I couldn't actually make the partition for the swap or a third Linux OS. Question 1: What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?? Thank you in advance for your advises and suggestions and Happy New Year to All!!

    Read the article

  • Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

    - by Tim
    Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

    Read the article

  • Unity3d web player fails to load textures

    - by José Franco
    I'm having a problem with Unity3d Web Player. I have developed a project and succesfully deployed it in a web app. It works with absolutely no problem on my PC. This app is to be installed on two identical machines. I have installed them in both and it only works properly in one. The issue I have is on a computer it fails to properly load the models and textures, so the game runs but instead of the models I can only see black rectangles on a blue background. It has the same problem with all browsers and I get no errors either by the player or by JavaScript. The only difference between these computers is that one that has the problem is running on Windows 8.1 and the other one on Windows 8 only. Could this be the cause of the issue? It works fine on my computer with Windows 8.1. However both of the other computers have specs that are significantly lower than mine. I have already searched everywhere and it seems that it has to do with the individual games, however I think it may have to do with the computer itself because it runs properly in the other two. The specs on the computes I'm installing the app on are as follows: Intel Celeron 1.40 GHz, 2GB RAM, Intel HD Graphics If anybody could point me in the right direction I would be very grateful I forgot to mention, I'm running Unity Web player 4.3.5 and the version on the other two computers is 4.5.0

    Read the article

  • Ubuntu 12.04LTS stuck at login mouse and keyboard not responding

    - by user169954
    I have Ubuntu 12.04LTS installed on a dual-booted machine (i5 dual core 8G ram) and it's been working fine, but today for some reason when I logged out and tried to log back in it is stuck at the login page, i.e. the mouse and the keyboard are not responding. The mouse is stuck at the top left corner of my screen, and I can do nothing but to turn the machine off. (I have been using logitech wireless mouse and keyboard.) I can not access the virtual console (Alt-F1 or Cntrl-Alt-F1) either! Here is what I have tried so far: Verified it is not a H/W problem since the mouse and keyboard work fine with windows7 Booted with ubuntu installation dvd and ran trial mode and mouse and keyboard worked fine. Tried bypassing the login screen by booting into recovery mode and editing tty1.conf, but to no avail. I moved .Xauthority .profile and .bashrc from my $HOME to another location so my login would proceed completely by system defaults. But this did not help From recovery mode commandline used to dpkg-reconfigure to switch between gdm and lightgdm. This did not help either. By the way, when in recovery mode as root from command line I mount the filesystem, all apps work fine. Python is Ok, octave is ok, vi is ok etc. I have a feeling if I could only bypass the login screen, and automatically get into the desktop, I will be ok. But I haven't been able to accomplish this either. I desperately need help please. Thank you in advance. Update: So I tried to switch to lightdm by dpkg-configure lightdm. This at least brings me up to the classical linux commandline login prompt but without a gui. Should I install startx? Should I install ubuntu-desktop?

    Read the article

  • Ubuntu crashes with menu bar launcher freeze during software centre use

    - by UbunUser
    I recently reinstalled Ubuntu 12.04 LTS on a Dell Studio 1588 64-bit and ran into crashes as I was installing some software on the software centre. Before this, I had display/screen problems that I needed to fix so I will briefly describe that in case it has any connection to the crashes. The problem was of screen crash/flickering (related to ATI Mobility Radeon HD 5400x) when trying to adjust brightness and so I followed guidance from an earlier chain (question 131967) to (a) use jockey to install fglrx update driver (deactivate experimental beta driver) and (b) edit grub to add acpi_backlight=vendor dell_laptop.backlight=0 The crashes that happened (twice, while software centre was just finishing installation in the background) was that all tabs (on open Firefox window) stayed open along with cursor control with mousepad but all menu bars disappeared completely along with the launcher and the keyboard also turned unresponsive. So there seemed to be no way to close windows or shut down the computer except for a forced hard shut down of the system using the start button. This is very similar to Questions #167540 and #298843, which seem to be closed. Why is this happening? Is there some update or fix I need to make? Thanks!

    Read the article

  • How do I get my graphic card to work properly?

    - by Lucas
    I been having some problems with my graphic card for a time now. But I had enough when I did'nt get Oil Rush to work on my HP Pavilion g6. The system has suggested hardware drivers for me, but the first time I installed them they pretty much fucked up the graphics. After some time I managed to get the computere to work properly (I thought) again. When the game did'nt work I tried to the hardware drivers for the graphic card anyway. First of all there was to possible choices insted of one, as the last time I installed the drivers (when it did'nt work out so good). The choices are: ATI/AMDs proprietary video drivers FGLRX (update for edition) and Proprietary FGLRX-video drivers for ATI/AMD I realized the drivers probebly are pretty much the same, so I tried the first one. But this did'nt work. Instead I was asked to "Look in to /usr/var/log/jockey.log". This did'nt helped me much. Instead I choiced the other one, wich was installed and after reboot there where some changes. First of all there was a lot more details for Unity that was'nt there before and some shortkeys are now working that did'nt before (like Ctrl + T and the Prt Sc-button). But overall everything doesn't work as it used to. Like when you browse between the workspaces it doesn't look the same. To get to the point: it doesn't work well right now even if I got some things better and now will not Oil Rush (as I mentioned in the beginning) even start. SO! Can someone give me any advice with this? I'm stuck. Can't manage to see whats wrong right now. Any help? My graphic card is AMD Radeon HD 6470M.

    Read the article

  • I am having trouble booting 12.04 keyboard and little man in circle appears and then nothing

    - by Rich J.
    I have a new system (ASUS 990FX mother board, 2 western dig drives, 32 gb memory, an ASUS nvidia video card (GeForce GTX560), and an ASUS DVD Burner (24B1ST)) I am struggling to get the 12.04 cd to work. I have been able to see the little man inside a circle and a graphic of a keyboard? with an == sign between them. Is this is a clue? What does it mean? After that the mauve screen with keyboard and little man in circle goes away. I get a dark background and underline cursor... even hear some work being done reading the rom.... but nothing appears on the screen. I haven't even got to the point where the graphic card is displaying improperly... it is just not displaying anything. If any kind soul has an idea about how to proceed, I am all ears. BTW, I have posted the issue to ASUS... waiting for reply.

    Read the article

  • Touchpad right click doesn't work on HP Envy 14 beats

    - by jdrageme01
    I have Ubuntu 12.04 lts 64 bits on my HP envy 14 beats. When I try to click with the right click button it doesn't work. Only works click in the touchpad directly and with usb mouse. 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) 00:01.1 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0105] (rev 09) 00:01.2 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0109] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) 00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 05) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series] [1002:6741] 09:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) 0a:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) 0b:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04)

    Read the article

  • No boot or grub file after using ls command

    - by Poke Moke
    I had xubuntu installed, i believe version 12.04 and then tried to dual boot with backbox. It worked from the flash drive but upon installing it onto the hard drive, I could no longer boot backbox. I decided I would just clear my OS and put just backbox on the hard drive and only have a single boot. To do this, I erased my boot file completely which led to my current position. I am put into the grub rescue prompt. I can't do a system restore, I can't boot with anything I might try including puppy linux and a boot rescue, and I've looked up the commands and I've tried to fix this. I can do ls, I find the correct hd but then I'm stuck as I don't have a boot or grub folder. The command is typed as: ls (hd1,msdos1)/ and listed is ./ ../ lost+found/ etc/ media/ bin/ dev/ home/ lib/ mnt/ opt/ proc/ root/ run/ sbin/ selinux/ srv/ sys/ tmp/ usr/ var/ initrd.img vmlinuz cdrom/ apfolder initrd.img.old vmlinuz.old (not sure if it's initrd or init rd.img. as it wraps around the screen there.) I've seen commands regarding boot or grub if they are seen but as listed, they aren't there. Any ideas?

    Read the article

  • Battery is drained too quickly

    - by LucaB
    I'm getting really low battery life under ubuntu, not even close to windows. I tried powertop, and I saw that my laptop is consuming in idle nearly 20 watts (a bit more). I tried to install laptop-mode-tools, change "good" into "bad" in powertop, but nothing changes. I see that I have the the HD audio output device which is running at 100% every time. Could this be the problem? This is a report from powertop. The battery reports a discharge rate of 22.8 W The estimated remaining time is 33 minutes Summary: 381.8 wakeups/second, 0.0 GPU ops/second and 0.0 VFS ops/sec Usage Events/s Category Description 3.2 ms/s 182.7 Timer tick_sched_timer 100.0% Device Audio codec hwC0D3: Intel 7.9 ms/s 25.1 Process /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background no 1.9 ms/s 24.2 Interrupt [6] tasklet(softirq) 2.9 ms/s 23.2 Process /usr/lib/chromium-browser/chromium-browser --type=zygote 8.1 ms/s 20.3 Process /usr/lib/unity/unity-panel-service 0.7 ms/s 17.4 Timer hrtimer_wakeup 4.2 ms/s 12.6 Process unity-2d-panel 604.4 µs/s 9.7 Process syndaemon -i 2.0 -K -R -t 149.7 µs/s 9.7 kWork ieee80211_iface_work 0.8 ms/s 8.7 Process metacity 19.5 ms/s 1.0 Process powertop 3.0 ms/s 6.8 Process //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session 699.0 µs/s 6.8 Process /usr/lib/thunderbird/thunderbird 4.3 ms/s 4.8 Process gnome-terminal 658.9 µs/s 2.9 Interrupt [1] timer(softirq) 75.1 µs/s 2.9 kWork iwl_bg_run_time_calib_work 163.8 µs/s 1.9 Process /usr/lib/accountsservice/accounts-daemon 70.6 µs/s 1.9 Process [ksoftirqd/2] 25.8 µs/s 1.9 Process [ksoftirqd/0] 1.0 ms/s 1.0 Process /usr/bin/python /usr/sbin/powernapd 408.2 µs/s 1.0 Process unity-2d-shell 189.8 µs/s 1.0 Process /usr/lib/chromium-browser/chromium-browser 124.4 µs/s 1.0 Process /usr/lib/unity-lens-applications/unity-applications-daemon 113.3 µs/s 1.0 Process /usr/lib/gnome-settings-daemon/gnome-settings-daemon 112.0 µs/s 1.0 Process nautilus -n 104.9 µs/s 1.0 Process /usr/lib/gvfs/gvfsd-trash --spawner :1.2 /org/gtk/gvfs/exec_spaw/0 77.5 µs/s 1.0 Process /usr/lib/x86_64-linux-gnu/colord/colord 75.6 µs/s 1.0 Process /usr/lib/gvfs/gvfs-gdu-volume-monitor 75.0 µs/s 1.0 Interrupt [53] i915 74.9 µs/s 1.0 Process /usr/lib/gvfs/gvfs-afc-volume-monitor What should I do to make the battery consumption lower?

    Read the article

  • ATI Radeon 5800 series dual monitor unity not 3D accelerated

    - by Victor S
    When I had a single monitor setup, without Xinerama, with my current setup of Ubuntu 11.10, ATI 5800 series card, Unity showed transparencies, shadows, etc. (although graphics was reported as 'Standard' in the control/settings panel). Having switched to a dual monitor setup, dell 24" UltraSharp and a smaller Acer monitor, Unity shows only as 2d, even though I'm not loggin in to that display manager. WebGL performance is very sluggish, I'm getting the impression that the processor is doing all the work and the card isn't even accessible even though the drivers are installed (from the ubuntu repository, I did not compile custom drivers). Any tips on how to enable full 3D accelerationn and video card support. Here is my xorg.conf file: Section "Monitor" Identifier "0-DFP3" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1680x1050" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-DFP4" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1920x1200" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-0" Device "amdcccle-Device[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-1" Device "amdcccle-Device[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Module" Load "glx" EndSection Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[1]-0" 0 0 Screen "amdcccle-Screen[1]-1" 1920 0 EndSection Section "Device" Identifier "amdcccle-Device[1]-0" Driver "fglrx" Option "Monitor-DFP4" "0-DFP4" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "amdcccle-Device[1]-1" Driver "fglrx" Option "Monitor-DFP3" "0-DFP3" BusID "PCI:1:0:0" Screen 1 EndSection Section "ServerFlags" Option "Xinerama" "on" EndSection More info: fglrxinfo display: :0 screen: 0 OpenGL vendor string: ATI Technologies Inc. OpenGL renderer string: ATI Radeon HD 5800 Series OpenGL version string: 4.1.11005 Compatibility Profile Context

    Read the article

  • How to debug suspend?

    - by mlissner
    I've been using Ubuntu for about five years now, and I still can't make it suspend when I want to. It's quite irritating that I can program up a storm, hack the machine in numerous other ways, and yet, and yet when I try to make it suspend or debug suspend, I fail miserably. I need help. Where do I begin to find the problem? What do I do to fix it? I'm placing a bounty on this, because I've literally lost hours of my life to this problem, and leaving my computer on ALL the time is terrible. The symptoms: Pressing suspend brings my computer to a state where it has a blinking cursor, the fans are running, it seems that the HD has turned off (I think), and I can't do anything to bring it back from this state (short of a hard reboot). Possibly related: My fans stay on even after a shutdown, and even then, I have to press the power button for five seconds before I can start it up again. I don't know what logs to look at to debug the problem, and I imagine they'd get nuked on reboot anyway. Please, please help. This drives me completely nuts, and I've been living with it for over a year.

    Read the article

  • How to fix Java problem installing Matlab 2012a (64-bit) in Ubuntu 12.04 (64 bit)?

    - by Sabyasachi
    I am trying to install Matlab 2012a (64-bit) in Ubuntu 12.04LTS (64-bit). I have installed Java 7. My Java version is: sabyasachi@sabyasachi-ubuntu:~/Downloads/R2012a_UNIX$ java -version java version "1.7.0_05" Java(TM) SE Runtime Environment (build 1.7.0_05-b05) Java HotSpot(TM) 64-Bit Server VM (build 23.1-b03, mixed mode I am getting the following error while installing Matlab: sabyasachi@sabyasachi-ubuntu:~/Downloads/R2012a_UNIX$ ./install Preparing installation files ... Installing ... /tmp/mathworks_18824/sys/java/jre/glnxa64/jre/bin/java: error while loading shared libraries: libjli.so: cannot open shared object file: No such file or directory Finished How can I fix this problem? When I use -v (verbose) option I am getting the following: sabyasachi@sabyasachi-ubuntu:~/Downloads/R2012a_UNIX$ sudo ./install -v Preparing installation files ... -> DVD = /home/sabyasachi/Downloads/R2012a_UNIX -> ARCH = glnxa64 -> DISPLAY = :0 -> TESTONLY = 0 -> JRE_LOC = /tmp/mathworks_26521/sys/java/jre/glnxa64/jre -> LD_LIBRARY_PATH = /tmp/mathworks_26521/bin/glnxa64 Command to run: /tmp/mathworks_26521/sys/java/jre/glnxa64/jre/bin/java -splash:"/home/sabyasachi/Downloads/R2012a_UNIX/java/splash.png" -Djava.ext.dirs=/tmp/mathworks_26521/sys/java/jre/glnxa64/jre/lib/ext:/tmp/mathworks_26521/java/jar:/tmp/mathworks_26521/java/jarext:/tmp/mathworks_26521/java/jarext/axis2/:/tmp/mathworks_26521/java/jarext/guice/:/tmp/mathworks_26521/java/jarext/webservices/ com/mathworks/professionalinstaller/Launcher -root "/home/sabyasachi/Downloads/R2012a_UNIX" -tmpdir "/tmp/mathworks_26521" Installing ... /tmp/mathworks_26521/sys/java/jre/glnxa64/jre/bin/java: error while loading shared libraries: libjli.so: cannot open shared object file: No such file or directory Finished sabyasachi@sabyasachi-ubuntu:~/Downloads/R2012a_UNIX$

    Read the article

  • Screen doesn't turn back on after resume on a Lenovo Thinkpad T420

    - by Wojtek
    Every time I suspend my notebook (Lenovo Thinkpad T420 - Intel HD graphic card) on Oneiric Ocelot 11.10 and turn it back on, the screen is black. The backlight is on and the system itself loads fine, but the display somehow doesn't get back. The first time after a fresh reboot the screen isn't black, it is mostly white/light-gray and it looks a bit like a distorted image. The pixels fade in until it gets almost completely light-gray. I've got a workaround for this: I switch to the first terminal (CTRL+ALT+F1) and back to X (CTRL+ALT+F7). In most cases that helps. Sometimes, when there's still a problem, I log in on the first terminal and run "unity --reset". Then go back to X - this helps always. I can tell that the system comes back, because I can log in with my fingerprint reader (or wait a bit and put in the password) "blindly", then do the workaround - I am logged in after the screen comes back. So it's only the display that is not working. Any help or advice where to look would be appreciated.

    Read the article

  • xorg-edgers PPA with llvmpipe breaks AMD APU system

    - by linux_RRT
    I've read before where this had happened to another user with the same system... I was running Ubuntu 12.04 LTS with Kernel 3.2.0.29 and decided to give xorg-edgers a try. I purged fglrx* and xorg* before beginning. I upgraded with sudo apt-get upgrade -d The system downloaded and installed 109MB worth of data to the system, including llvmpipe which I am very unfamiliar with, and Kernel 3.5.0.11. The system was then rebooted to finalize the upgrade. The system boots to a black screen and then tells me "The system is running in low-graphics mode". Did I miss a step in the install? Or do the newest open-source drivers just not work with my hardware? I realize this hardware (APU) is some of the newer development. I dropped to command via the fallback menu and attempted to boot lightdm as root, but the system hangs in 'Configuring kernel parameters' at Starting initializes zram swaping. ...and then it just sits there. The other thing that concerns me is the output at the top of the screen that says: could not write bytes: Broken pipe Does llvmpipe work for this type of system? To be clear the system is: MSI x370-206us Laptop Radeon HD 6320 AMD e450 APU 1.67ghz dual-core Any help would be much appreciated. Like I said, I'm pretty sure I followed the right order of operations for the install procedure, but I was curious if anyone with similar hardware had experienced anything similar.

    Read the article

  • Install Mac OS Lion on Macbook with existing Ubuntu 12.04 dual boot

    - by kash
    I don't usually create my own questions, because I can find what I need through other people's questions. However, this one doesn't seem to be anywhere, except in one place where someone is talking about not using Apple hardware. So here it goes. I am using Apple hardware. I have a MacBook 1,1 with Intel Core2Duo running Ubuntu Precise Pangolin flawlessly. I never considered starting with Mac OSx and dual-booting because I never liked Mac OS. Now that I'm realizing that the only way I'm going to be able to run my DAW (Reaper) nicely and use a Firewire recording interface is to run Mac OSx, I'm considering it again. I want to go the opposite direction of most people and install Mac OSx next to an existing Ubuntu installation and have a boot menu with refit. I've installed refit in Ubuntu and I've converted the .dmg file for Mac OS Lion to a .iso file. Now, should I mount the .iso in Ubuntu and run it there, or burn a DVD and restart? I'm trying to gauge how to do this without hurting my existing Ubuntu installation. I will of course keep looking for existing answers in the meantime.

    Read the article

  • How to install Ubuntu 12.04.1 in EFI mode with Encrypted LVM?

    - by g0lem
    I'm trying to properly install Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with the alternate install CD ".iso" on a lenovo Thinkpad X220. Default Hard Disk (with a pre-installed version of Windows 7) has been replaced with a brand new SSD. The UEFI BIOS of the lenovo Thinkpad X220 is set to "UEFI Boot only" & "USB UEFI BIOS Support" is enabled (I'm using an external USB DVD reader to perform Ubuntu installation). The BIOS is a Phoenix SecureCore Tiano, BIOS version is 8DET56WW (1.26). The attempts below are made with the UEFI BIOS settings described above. Here's what I've tried so far: Boot on a live GParted CD Create a GPT partition table Create a FAT32 partition for UEFI System, set the partition to "EF00" type ("boot" flag) Leave remaining space unformated Boot on Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with alternate CD: Perform the install with network updates enabled Use manual partitioning FAT32 partition created with GParted is used as "EFI System partition" Remaining space is set to be used as "Physical volume for LVM" Then "Configure encrypted volumes" using the previous "Physical volume for LVM" as the encrypted container, passphrase is setup. "Configure the Logical Volume Manager" creating a volume Group using the encrypted container /dev/mapper/sda2_crypt Creation of the Logical Volumes "Create logical volume", choosing the previously created volume Group Assign a mount point and file system to the Logical volumes : LV-root for / LV-var for /var LV-usr for /usr LV-usr-local for /usr/local LV-swap for swap LV-home for /home NOTE: /tmp would be in RAM only using TMPFS Bootloader step: neither my ESP partition (/dev/sda1, /dev/sda or MBR) seems to be the right place for GRUB, I get the following message (X suffix is for demonstration only): unable to install grub in /dev/sdaX Executing 'grub-install /dev/sdaX' failed This is a fatal error. Finish installation without the Bootloader & Reboot The system doesn't start, there's no EFI/GRUB menu at startup. What are the steps to perform a clean and working installation of Ubuntu 12.04.1 Precise Pangolin, 64bit version in U(EFI) mode using the encrypted LUKS + LVM scheme described above?

    Read the article

  • 11.10 liveCD black screen

    - by Shaun Killingbeck
    Attempting to install/try ubuntu 11.10 on my new laptop, using a liveCD (and tried USB). I get the purple screen (with the man/keyboard at the bottom) and after that the screen flashes bright white before going black. Ubuntu continues to load in the background, with login sound etc but the screen is off. I have tried as many different solutions as I could find including: using nomodestep, xforcevesa, i915.modeset=0 in boot options (seperately): varying consequences, but either I end up at a blinking cursor with no prompt, a command line (startx fails: no screen found), or the original blank screen again Tried booting from VirtualBox - it crashes at the same place the screen would go blank when using a CD/USB tried 11.04: I don't have this problem BUT when trying to install, I get a ubi-partman error 141 (possibly down to the three partitions that came on my laptop... not sure why HP needed there own separate partition for HP Tools...) Model: HP Pavillion DV6 6B08SA Processor: AMD Quad-Core A6-3410MX APU with Radeon HD 6545G2 Dual Graphics (1.6 GHZ 4 MB L2 cache ) Chipset: AMD RS880M Any help would be greatly appreciated. I just want to be able to partition the drive and install Ubuntu. I'm assuming the issue is graphics card related, although I have no confirmation of that. I have caught a glimpse of some output to do with pulseaudio and [fail], but I can't imagine why that would cause a screen problem and the sound definitely works anyway.

    Read the article

  • Problem graphics with ATI Radeon x1270 (RS690M) on Ubuntu 12.04

    - by Giuseppe Della Corte
    I'm Italian and so I apologize for my English! I'm a beginner to Ubuntu and I tried it on my desktop PC and it's fantastic, fast and fun! I decided to try it on my netbook Packard Bell DOT M/A and this is the configuration: AMD Athlon L110 1.2GHz 2GB of RAM ATI Radeon x1270 (RS690M) 150GB Hard Disk I installed Ubuntu 12.04 with Wubi (dualboot Windows 7 + Ubuntu 12.04), because the netbook does not have a DVD player! During the installation everything is OK, after it was installed I see mistakes in the graphical display! I see objects that are seen in different colors and moving (buttons, mouse pointer, text bar ... etc ...) At one point came not to see anything, such as this screenshot: The drivers are open, that is already installed in Ubuntu. Windows 7 video card runs fine, can run well Aero (transparent window effects), I can watch movies in HD and play some games with the Catalyst drivers from AMD. Now I ask a favor, you can help me solve this problem? Is there a fix for this driver or drivers different on the Internet? Thanks for your attention, good bye!

    Read the article

  • How do I debug an overheating problem?

    - by Tab
    Hello guys. I have a problem with my Laptop (Dell Inspiron 1564 Core i5 4GB Ram VGA ATI Mobility Radeon HD 4300 running Ubuntu 10.10 32bit). It shuts down abruptly without even a lag in the application I am working with before shutdown. I think it's overheating problem. Actually the laptop is hot all the time when I am running Ubuntu. When I switch back to windows, even with intense load it won't shutdown or show any problem as long as I keep proper ventilation (when the air openings are blocked it does the same). Actually on Ubuntu i don't usually do things that need much CPU power, usually surfing internet, coding web pages and sometimes playing with python and ruby. I am not enabling desktop effects so no GPU load except the normal GNOME gui. Now as I am writing the Processor load in the panel monitor applet is 0%, Memory 11% by programs, 22% by cache. And i have CPU Frequency monitor for each of the 4 cores set to 1.20 Ghz (the lowest possible value, i am not sure if this applet does really limit CPU usage). Running sensors in terminal gave me temp1: +26.8°C (crit = +100.0°C) temp2: +0.0°C (crit = +100.0°C) hddtemp /dev/sda at the terminal gave me /dev/sda: WDC WD3200BEVT-75ZCT2: 46°C All that fine but the laptop is Really hot i can feel it in the keyboard, mouse pad is painful to touch, and the fan is always spinning. I am also placing 2 small fans running on USB under the laptop right now and the laptop is lifted over the fans so it's well ventilated. When I am running windows it doesn't get that hot except when there is a really big load on the CPU and this is keeping me away from using Linux for everyday tasks. Actually I don't care much for speed as I can deal with low speed it's not going to shutdown abruptly. So please if you can help me and tell me what are the possible causes, where should I start ?

    Read the article

  • Ubuntu 12.04 Freezes at Bootup

    - by Ryan Yu
    I have an Acer Aspire One Model AO722, that has a dual-boot configuration with Windows 7 Home Premium and Ubuntu 12.04. Processor: AMD C-50, 1.00GHz 2.00GB ram, 64-bit, AMD Radeon HD 6250 Graphics. I installed Ubuntu two days ago, and since then, loading it has been sporadic. Windows 7 still loads just fine, but Ubuntu will sometimes freeze. First time I booted Ubuntu up, it ran no problem. Worked with it for half an hour, then shut down the computer. The second time I booted it up, it froze after ten minutes when I was trying to set up Thunderbird. Third time, same thing. Fourth time, it froze about 5 minutes after bootup when I was trying to connect to my wifi. Fifth time, it ran no problems for about 5~ hours. Then, three consecutive times I've restarted (what is it, the 6th, 7th, and 8th times?) it has gotten to the login screen, I've entered my password, all the text on the page disappears as if its going to load my desktop, and it freezes. A minute ago when I booted Ubuntu up for the 9th time, it loaded the desktop fine. Who knows if it'll crash soon; probably, though. Any ideas?

    Read the article

< Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >