Search Results

Search found 6622 results on 265 pages for 'match'.

Page 125/265 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

• Too much free space on FreeNAS - ZFS

  - by Guillaume

  I have a FreeNAS server with 3 x 2 To disks in raidz1. I would expect to have about 4 To of space available. When I run zpool list I get: [root@freenas] ~# zpool list NAME SIZE USED AVAIL CAP HEALTH ALTROOT main_volume 5.44T 3.95T 1.49T 72% ONLINE /mnt I was expecting a size of 4 To. Also, used space as reported by zpool list does not match what's reported by du: [root@freenas] ~# du -sh /mnt/main_volume/ 2.6T /mnt/main_volume/ There are quite a few things that I dont yet completely understand about ZFS. But at the moment I am mostly worried that I misconfigured my system and that I dont have any storage redundancy. How can I make sure I did not do an horrible mistake ... For the sake of completeness, here is the output of zpool status: [root@freenas] ~# zpool status pool: main_volume state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM main_volume ONLINE 0 0 0 raidz1 ONLINE 0 0 0 gptid/d8584e45-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d8f7df30-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d9877cc3-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 errors: No known data errors

  Read the article

• ffmpeg add two audio streams to video

  - by Tossin Hausen

  I tried this: ffmpeg -i /sdcard/video/transcode/video.avi -map 0:0,0 -i /sdcard/video/transcode/first.mp3 -map 1:0,1 -i /sdcard/video/transcode/second.mp3 -map 2:0,2 -acodec copy -vcodec py /sdcard/video/transcode/Output.avi to add two audio streams to one video file. But ffmpeg says the number of mappings should match the number of output streams. What is wrong here? I'm trying to work with an Android build of FFmepg "ffmpeg for android beta". "Does not work" means that this uncommunicative Android build of FFmpeg just stops without giving any error message. The -codec copy option does not work with this build. Now I tried the same set of files with the FFmpeg called command line tool that comes with Ubuntu 10. Something (can't say where it is from). The -codec copy option does not work with this FFmpeg too. Here the complete output: m30x:~/movie/Film$ ffmpeg -i input.avi -i first.mp3 -i second.mp3 -map 0 -map 1 -map 2 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x93cfd10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Input #2, mp3, from 'second.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #2.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Number of stream maps must match number of output streams Merging only one audio stream with the video stream works with Ubuntu and Android version of FFmpeg. Here the complete output: ffmpeg -i input.avi -i first.mp3 -map 0 -map 1 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x9bfad10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Output #0, avi, to 'output.avi': Stream #0.0: Video: mpeg4, yuv420p, 576x432, q=2-31, 90k tbn, 25 tbc Stream #0.1: Audio: libmp3lame, 22050 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding frame= 6157 fps=6156 q=-1.0 size= 31667kB time=246.28 bitrate=1053.3kbits/s Do you have an idea why it does not work with two audio streams? By the way, ffmpeg -i input_with_first_audio_stream.avi -i second.mp3 -acodec copy -vcodec copy output_two_audio_streams.avi -newaudio works with both versions of ffmpeg that I use, but the first audio stream is played too fast (x10 or more), while the second audio stream is played correct. Many thanks in advance and sorry for my unconventional question and outdated versions of ffmpeg. But I am a lamer and it is not so easy for me to compile from the source (especially for the Android version). I will try to compile an up to date version of ffmpeg with Ubuntu, but I don't have much free time.

  Read the article

• Setup dhcpd without gateway on purpose

  - by MBober

  I have an XP machine with two network interfaces. One is connected to my company's network (and the Internet). The other is a very local network which connects some hardware with my PC. Both the hardware and my XP machine's second network interface obtain configuration from a dhcpd running on Ubuntu in a virtual machine on my XP machine. I entered some dummy gateway in /etc/dhcp3/dhcpd.conf like 192.168.3.1 which does not match any existing device just to get dhcpd started. The problem is that my XP machine now tries to route Internet traffic through 192.168.3.1 in most of the cases which, of course, results in an error. Is there any way to set up dhcpd in a way that the clients know that there is no gateway in this network? By the way: setting the gateway manually in XP is off the table because this needs administrator privileges which I don't have.

  Read the article

• How to redirect (or Alias) jump page with Apache

  - by Meltemi

  I'm not an Apache expert but need to make a small change to a web server. We are introducing a "jump page" URL that is different from a primary URL (for tracking reasons). /productA/index.html /productA/jump_index.html Basically i want to log that jump_index.html was requested and then return index.html. I don't want the client to wait 8 seconds or so for a redirect. How should we be handling this? Simply symlink (or alias) the file in the filesystem? Use mod_alias Alias Match (if so how exactly)? something better still? Edit: mod_rewrite in httpd.conf: <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_METHOD} ^TRACE RewriteRule .* - [F] </IfModule>

  Read the article

• NFS share access - Permission denied

  - by rgngl

  I'm trying to share a directory on my NAS device(WD Mybook WE) with NFS to another machine on my local network. The directory on the NAS device looks like this: drwxr-x--- 15 git git 4096 Nov 17 01:05 git/ And id's of the user git on the NAS device is like this: [root@myhost DataVolume]# id git uid=505(git) gid=505(git) I played with many different parameters in the /etc/exports file and this is what I got there currently: /DataVolume/git 192.168.0.20(async,rw,no_root_squash,no_subtree_check) On the client side I have the user git and group git with the same id's to match the ones on the server. user@myclient:~$ id git uid=505(git) gid=505(git) groups=505(git) I mount the directory with: sudo mount myhost:/DataVolume/git -t nfs git/ and the mounted directory looks like: drwxr-x--- 15 git git 4096 Nov 17 01:05 git After these steps I can't seem to cd to that directory with any user, including git and root. I am getting a Permission denied error. Thanks in advance for any help.

  Read the article

• PHP Kohana CentOS 5

  - by Undefined

  Trying to deploy a Kohana based project in CentOS 5. Installed PHP 5.3.1 but still getting the following error. Warning: preg_match() [function.preg-match]: Compilation failed: this version of PCRE is not compiled with PCRE_UTF8 support at offset 0 in /usr/local/apache2/htdocs/icarus/system/core/utf8.php on line 30 Fatal error: PCRE has not been compiled with UTF-8 support. See PCRE Pattern Modifiers for more information. This application cannot be run without UTF-8 support. in /usr/local/apache2/htdocs/icarus/system/core/utf8.php on line 38 Trying since last 2 days, i upgraded my PHP from 5.1 to 5.3 but still getting the same error.The problem as per me is that the PCRE module of PHP in phpinfo() says is of sep 2004. Below is the actual line PCRE Library Version 5.0 13-Sep-2004 Can anyone tell me how to upgrade it or wats the solution to the problem. Thanks.

  Read the article

• ft_stopword_file not picked up

  - by Alex Holsgrove

  I have a VPS server with a company called Webfusion. I want to remove some or all of the FULLTEXT stopwords because some specific words needs to be searchable with my DB content. I opened /etc/mysql/my.cnf and added the line ft_stopword_file="". I restarted the mysql service, ran a repair table and then tried my MATCH query with no success. I ran SHOW VARIABLES LIKE 'ft_%' and it simply shows (built-in) next to the stopword file. I am running WAMP on my workstation, and whilst I realise this isn't configured the same as a commercial VPS, the above method worked just fine. Couple someone please offer some guidance?

  Read the article

• One PC, 4 iOS Devices, 4 iCloud Accounts?

  - by Eric J.

  I have one PC running iTunes, my iPhone, and one iPod for each of three kids. Ideally I would like the iPhone to use my iCloud account and each iPod to use an iCloud account specific to each kid. According to Apple: You can ... use one Apple ID for iCloud services and another Apple ID for store purchases However, the method described Enter the Apple ID you want to use for iCloud in Control Panel Network and Internet iCloud. Enter the Apple ID you want to use for Store purchases (including iTunes in the Cloud and iTunes Match) in iTunes iTunes Store. would require that all iOS devices share the same iCloud account if they use iTunes on the same PC. Short of having one PC per family member, is there a method to use different iCloud accounts on each iOS device?

  Read the article

• Web-based (intranet / non-hosted) timesheet / project tracking tools

  - by warren

  I realize some similar questions have been asked along these lines before, but from reading-through them today, it appears they don't match my use case. I am looking for a web-based, non-hosted time and project tracking tool. I've downloaded Collabtive so far, but am looking for other suggestions, too. My list of requirements: runs on standard LAMP stack non-hosted (ie, there is an option to download and run it on a local server) not a desktop/single-user application easy-to-use - my audience is a mix of technical and non-technical folks easy to maintain - when time for upgrading comes, I'd really like to not have to rebuild the app (a la ./configure ; make ; make install) needs to support multiple users free-form project additions: we don't have a central project management authority (users should be able to add whatever they're working on, not merely from a drop-down) Does anyone here have experience with such tools? It doesn't have to be free.. but free is always nice :)

  Read the article

• Bad disks in ancient server

  - by Joel Coel

  I have a 1998-era Netware 3.12 server that runs everything on our campus: general ledger, purchasing, payroll, student information, grades, you name it. The server has an Adaptec RAID controller with two volumes: RAID 1, 2 17GB scsi disks, Seagate ST318417W RAID 5, 3 4GB scsi disks, 2 Seagate ST34573W and 1 ST34572W. We are currently in the early stages of a project to replace this system, but you don't just jump into a new system like that and so I need to keep this server running until at least November 2011. This week we had not one but two hard drives fail. Thankfully they are from different volumes and we're able to keep running for the moment, but given the close nature of these failures I have serious doubts that I'll be able to avoid catastrophic failure from this server through the November target as is without restoring the RAID redundancy — it'll only take one more drive failure anywhere and I'm completely hosed. We are fortunate enough to have exact match "spares" lying around for both drives, but the spares are in unknown condition. I tried swapping just them in, but the RAID controller isn't smart enough to handle this and it renders the system unbootable. As for the RAID controller itself, there is utility I can get into during POST via a Ctrl-A shortcut, but I can't do much useful from there. To actually manage volumes I must first boot in to Netware, at which point I can use CI/O Array Management Software Version 2.0 to actually look at volume information. I suspect that the normal way to manage things is to boot from a special floppy with the controller software on it, but that floppy is long gone. Going through the options in the RAID software, I think the only supported way to replace a disk in an existing RAID volume is to physically add the disk, boot up and configure it as a "spare" for a volume, force the volume to use the spare to replace an existing down disk (and at this point I'm only guessing) so that the down disk becomes the spare, repair the volume, remove the spare from the volume, and then shut down and remove the disk. Then start all over for the other failed disk. All this amounts to a lot of downtime, assuming I can even make it work and that my spares are any good. As for finding reliable spares, I have no clue where to even begin looking to find a new 4GB scsi drive, or even which exact scsi system I'm looking for, as it's gone through a few different iterations over time. Another option is to migrate this to a virtual machine (hyper-v), but all previous attempts we've made in this area have failed to get very far. When this machine was installed I was just graduating from high school, and so it requires lower level knowledge of netware and dos than I ever developed, or if I did have since forgotten (I'm not exactly a dos neophyte, either). Part of my problem is this is a high-use server, and taking it down for a few days to figure things out isn't gonna fly very well. As for the question, I'm looking for anything that might be helpful in this situation: a recommendation on a place to find good spares from this era, personal experience repairing RAID volumes using a similar controller or building a hyper-v vm from an old netware server, a line on a floppy with better software for the RAID controller, recommendation on a good Novell consultant in Nebraska that would be able to put things right, a whole other option I haven't considered yet, etc. Update: For backups, we have good (recently verified via restore) backups of the data only -- nothing for the software that actually runs things. Update 2: Just a progress report that I currently have a working Netware 3.12 install in VMWare Virtual Server 2.0, thanks largely to the guide I found here: http://cerbulescubogdan.blogspot.com/2010/11/novell-netware-312-on-vmware.html The next steps are preparing empty netware volumes to match the additional volumes on my existing server, taking a dump of everything on the C:\ drive and netware volumes on my existing server, and figuring out from that information what modules need added to netware, installing my licenses (we do still have that disk, if it's any good), and moving data over. I have approval to bring the server down for a week after the first of the year (sadly not before), so, aside from creating empty volumes, the rest of the work will have to wait until then. Final Update (Jan 5, 2011): I was able to get spares working in both raid arrays without data loss this week. Both are now listed by the controller as "FAULT TOLLERANT" (yay!). I was also able to build on the progress from my last update and now have a functional "spare" server in VMWare Server 2.0. The spare can run and use our erp software, but I can't put it into production because I can't (yet) print from that box (and I have no idea why). Even so, this VM will do in a pinch if I have no other choice, and between it and the repaired RAID arrays I'm comfortable pushing on until I can junk the machine in November.

  Read the article

• How is this modsec rule getting triggered?

  - by BipedalShark

  I made a GET request to the URL, http://domain.tld/test/docs/index.php?create_table=1&step=2 and got a 403 response code. It turns out this modsec rule is getting triggered: Access denied with code 403 (phase 2). Pattern match "(?:ogg|gopher|zlib|(?:ht|f)tps?)\:/" at ARGS:gltr_redir. [file "/opt/mod_security/10_asl_rules.conf"] [line "827"] [id "340153"] [rev "22"] [msg "Generic PHP code injection protection via ARGS 3"] [severity "CRITICAL"] I would assume ARGS refers to GET/POST data, but there's no gltr_redir in the query string. And, being a GET request, there's obviously no POST data. So how is this rule being triggered?

  Read the article

• Reverse DNS (PTR) for Email

  - by user3169495

  We are hosting our website (http://www.redappleapartments.com) with a hosting company in Sweden. And we are using godaddy as our email provider. So, our smtp servers are smtp.europe.secureserver.net mailstore1.europe.secureserver.net Our website sends plenty of emails to our customers and we are sending via godaddy (using SMTP authentication). Some of the emails are never delivered to the recipients. And sometimes we see such warning: The hostname in the SMTP greeting does not match the reverse DNS (PTR) Can somebody out there suggest how we can solve this problem?

  Read the article

• Excel macro: Replace enitre cell contents; replace 1 but not 10, 11, 21 etc

  - by user65678

  I need to replace a large amount of numbers with words in an Excel spreadsheet. Eg: 1 = hello 12 = goodbye 4 = cat etc. I can do it with the standard search and replace, but i have a large list to work through (about 240 number/word combos), so i figured i would use a macro. I have this: Sub findreplacer() For Each mycell In Range("A1:A1000") mycell.Replace What:="1", Replacement:="hello" mycell.Replace What:="12", Replacement:="goodbye" mycell.Replace What:="4", Replacement:="cat" Next End Sub But it replaces the 1 in 12 so the cell reads hello2 instead of goodbye. How can i make it just affect cells that only contain the specific number, the way 'match entire cell contents' works? Any help appreciated.

  Read the article

• cannot connect to MS FTP 7.5 on Windows 2008 on Amazon EC2 instance

  - by minerj

  I have just installed the MS FTP 7.5 upgrade on my Windows 2008 Server (Service Pack 2) running on an Amazon EC2 instance. In the FTP Firewall Support settings for the server in IIS Manager I have set up the passive port range 45001 - 45005 and also set the External Firewall IP address to match the assigned Amazon Elastic IP address. Using the AWS Console I changed the Security Group for the server to allow access to the server through ports 21 and 45001 through 45005. Using an FTP client (either the command line FTP client or Windows Explorer) on the Amazon server I can connect to the FTP server but I cannot connect with an external FTP client. When I checked to see which ports were open on the server using Shields Up it shows that port 21 is open but ports 45001 to 45005 are closed. I assume I'm missing something. Any help greatly appreciated.

  Read the article

• How to set up wireless access on a Cisco router

  - by Carlos

  Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

  Read the article

• IE does not send NTLM domain

  - by Buddy Casino

  I have a problem with NTLM single-sign-on with IE8. We've got multiple domain controllers and users from multiple domains that we try to authenticate to a web application via NTLMv1 passthru. Somehow IE fails to send the user's domain in the NTLM Type 1 message. This has the effect that the webapp can not match users properly to their domain controllers, resulting in failed logon attempts, because a user from domain X tries to authenticate to domain controller Y. This problem does not occur with Firefox, as it always sends the correct domain header. So: how do I get IE to send the domain in the NTLM header?

  Read the article

• Reformat a WindowsXP drive: Quick, regular, or leave the current file-system

  - by Julie

  When reformatting, Windows XP ask me to choose from these formatting methods. (Implying that ALL of them are "formatting methods"... even #3) Reformat using NTFS (quick) Reformat using NTFS Leave the current file-system intact (no changes) What choice #3 really mean? Does it mean: A. Leave the current file-system (whatever file-system is already in use) and reformat to match that. (ie. If you current have NTFS, reformat to that again. If you currently have FAT32, reformat to that again. That is: Reformat without changing to a different file-system. Leave the current type.) or... B. Do absolutely nothing. Don't format. Don't delete any of my files. Abort the formatting process entirely.

  Read the article

• cannot connect to MS FTP 7.5 on Windows 2008 on Amazon EC2 instance

  - by minerj

  I have just installed the MS FTP 7.5 upgrade on my Windows 2008 Server (Service Pack 2) running on an Amazon EC2 instance. In the FTP Firewall Support settings for the server in IIS Manager I have set up the passive port range 45001 - 45005 and also set the External Firewall IP address to match the assigned Amazon Elastic IP address. Using the AWS Console I changed the Security Group for the server to allow access to the server through ports 21 and 45001 through 45005. Using an FTP client (either the command line FTP client or Windows Explorer) on the Amazon server I can connect to the FTP server but I cannot connect with an external FTP client. When I checked to see which ports were open on the server using Shields Up it shows that port 21 is open but ports 45001 to 45005 are closed. I assume I'm missing something. Any help greatly appreciated.

  Read the article

• Web-based (intranet / non-hosted) timesheet / project tracking tools

  - by warren

  I realize some similar questions have been asked along these lines before, but from reading-through them today, it appears they don't match my use case. I am looking for a web-based, non-hosted time and project tracking tool. I've downloaded Collabtive and Achievo so far, but am looking for other suggestions, too. My list of requirements: runs on standard LAMP stack non-hosted (ie, there is an option to download and run it on a local server) not a desktop/single-user application easy-to-use - my audience is a mix of technical and non-technical folks easy to maintain - when time for upgrading comes, I'd really like to not have to rebuild the app (a la ./configure ; make ; make install) needs to support multiple users free-form project additions: we don't have a central project management authority (users should be able to add whatever they're working on, not merely from a drop-down) Does anyone here have experience with such tools? It doesn't have to be free.. but free is always nice :)

  Read the article

• xslt apply-templates in second level

  - by m00sila

  I cannot wrap <panel> tags to second level individual items as shown in Expected result bellow. But with the xslt i have written, all 1.x get into single node. Please help me. Source xml <root> <step id="1"> <content> <text> 1.0 Sample first level step text </text> </content> <content/> <step> <content> <text> 1.1 Sample second level step text </text> </content> </step> <step> <content> <text> 1.2 Sample second level step text </text> </content> </step> <step> <content> <text> 1.3 Sample second level step text </text> </content> </step> </step> </root> Expected output <panel> <panel> 1.0 Sample first level step text </panel> <panel> 1.1 Sample second level step text </panel> <panel> 1.2 Sample second level step text </panel> <panel> 1.3 Sample second level step text </panel> </panel> My XSLT <xsl:template match="/"> <panel> <xsl:apply-templates/> </panel> </xsl:template> <xsl:template match="root/step" > <panel> <panel> <xsl:apply-templates select ="content/text/node()"></xsl:apply-templates> </panel> <panel> <xsl:apply-templates select ="step/content/text/node()"></xsl:apply-templates> </panel> </panel> </xsl:template>

  Read the article

• 4 - 7 second delay accessing Mysql across the network

  - by Kristiaan

  Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

  Read the article

• File not updating in symlink'd folder in IIS

  - by Daniel Short

  I have the following setup: Site1/Shared/ - Physical folder Site2/Shared/ - symlink using mklink to Site1/Shared I've updated a javascript file in Site1/Shared/scripts, and the change is being reflected on Site1. However, the change is not being reflected through IIS on Site2. When I open Site1/Shared/scripts/common.js and Site2/Shared/scripts/common.js, they match exactly. But when I view the files through Safari, Firefox, Chrome, IE, from any machine (even machines that have never visited the sites), the change is not reflected on Site2. Here are URLs to the files to review: Site 1: http://www.landsofamerica.com/shared/scripts/common.js Site 2: http://www.landsoftexas.com/shared/scripts/common.js These files look exactly the same when logged onto the server, and the shared folder under landsoftexas.com is a symlink created using mklink to the shared folder under landsofamerica.com. Any idea what might be causing IIS to serve the wrong file?

  Read the article

• Lookup Active Directory entry by implicit UPN

  - by Michael-O

  In our company exists a forest-wide UPN suffix company.com and almost all user accounts have the explicit UPN set to [email protected]. This value is also set in the Active Directory userPrincipalName attribute. Now we have an application where users perform authentication through Kerberos. So we are given the Kerberos principal, i.e. implicit UPN. We'd like to look up that user and retrieve several LDAP attributes. Since iUPN and userPrincipalName do not match anymore, the lookup is not possible. Is there any "official" way to retrieve a mapping from the Active Direcory? My workaround is to perform a LDAP bind against the realm component and search for the sAMAccountName attribute which matches the user id component of the iUPN. Searching for the mere sAMAccountName in the forest is not possible because the value is unique in the domain only.

  Read the article

• two samba servers and one ldap backend

  - by user2346281

  I had setup a Samba 3 server as PDC with a passdb LDAP backend. Server SID: S-1-5-21-3270... Domain: A Every user has a SambaSID beginning with this Server SID. But now I try to setup a second server for some shares. This server should use the same LDAP backend because I don't want to have two LDAP backends. Otherwise I have to do modifcations (e.g. add users) twice. Second Server SID: S-1-5-21-3797... Domain: B But now when a user try to mount this new share I see this error in samba log: The primary group domain sid(S-1-5-21-3797....) does not match the domain sid(S-1-5-21-3270...) for xxx(S-1-5-21-3270...). I understand the problem but what can I do to avoid to maintain two LDAP backends? Regards, Simon

  Read the article

• Help with Apache rewriteengine rules

  - by Vinay

  Hello - I am trying to write a simple rewrite rule using the rewriteengine in apache. I want to redirect all traffic destined to a website unless the traffic originates from a specific IP address and the URI contains two specific strings. RewriteEngine On RewriteLog /var/log/apache2/rewrite_kudithipudi.log RewriteLogLevel 1 RewriteCond %{REMOTE_ADDR} ^199\.27\.130\.105 RewriteCond %{REQUEST_URI} !/StringOne [NC, OR] RewriteCond %{REQUEST_URI} !/StringTwo [NC] RewriteRule ^/(.*) http://www.google.com [R=302,L] I put these statements in my virtual host configuration. But the rewriteengine seems to be redirect all requests, whether they match the condition or not. Am I missing something? Thank you. Vinay.

  Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >