Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 126/468 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

  • 2 x Netgear GS724T (Dual GBIC) trunking issue

    - by Arthor
    I have the following: Netgear GS724T (Firmware Version V1.0.3_35, Protocol Version - 2.001.002) 4 x Indineon ISFP GBR/FC Settings STP Function - Enabled Fast Link - Enabled Trunking port 23,24, (21,22 - RJ45 cables, but not connected.) I have connected both switches via 2 fiber cables and want to use trunking. The problem I am having. Sometimes I get a an issue when none of the switches cannot talk with each other, nor the devices, sometime they can. The problem is irregular and no patten can be determined The statistics shows that when the switches does not work, they have RX errors If I remove one to the GBIC connections, then everything works as normal.] Question Does anyone have a solution for this please? Thanks

    Read the article

  • I just ordered 70/10 line, and need a new router I think?

    - by data_jepp
    Before I had the 25/5 line and the n standard router did just fine. Now it doesn't do the job. Online speedtest reads at 82 so I have the line. But my laptop is getting less than 30 in my room. My laptop has the following WiFi card: http://www.intel.com/content/www/us/en/wireless-products/centrino-advanced-n-6205.html What is this talk about 2,5 and 5ghz? Can my laptop be connected at once over both bandwidths? And that would let me use the full 70Mb over wifi? Hope it's ok to ask network questions here.

    Read the article

  • How to I sync my windows mobile phone via wireless network

    - by Kibbee
    According to this article, I should be able to sync my Windows Mobile smartphone via my wireless internet connection. However, when I go to the connection settings, I only see USB and COM1 options. No option for ethernet. I have an HTC Maple (aka Snap), and it connects fine to my home wireless network, but I would like to be able to sync over the network.

    Read the article

  • Does anyone know about nagios plugin that uses nmap and does port checking??

    - by Eedoh
    Hi to all. I need to monitor open and closed ports on dozens of hosts. I've found a Nagios plugin that does what I need, but I would have to use this script through nrpe. Some of the hosts are powered by linux and they all have perl installed. But some of them are Windows machines, and it's not convenient for me to install perl on every one of them. That's why I can not use this plugin. I hope that there's Nagios plugin that uses nmap, or something similar, so it could check ports on every host remotely, without installing plugins on remote hosts, only on server.

    Read the article

  • windows server 2008 r2 remote desktop issue with roaming clients

    - by Patrick D'Haese
    I have the following situation : a Dell windows server 2008 R2 computer, with remote desktop services installed. I have installed a java application making use of a PostgreSql database, and made this application available for clients using RDP. Clients are standard Win XP pc's and Psion Neo handheld devices running Windows CE 5 Pro. The application works fine for clients on standard XP pc's connected directly via cat 5E Ethernet cable to a Dell Powerconnect 2816 switch. The Psion Neo clients connect wireless to the network via Motorola AP6532 access points. These access points are connected via a POE adapter to the same switch as the XP pc's. The Psion devices can connect without any problem and very quickly to the server and to the application using RDP. So far, so good. When the Psion devices move around in the warehouse, and they roam from one access point to the other, the RDP session on the client freezes for approx 1 minute, and then it automatically resumes the session. This freezing is very annoying for the users. Can anyone help in solving this issue? Update (August 9) : After re-installing the access points we have a working situation, but only when connecting to the RDP host : * via a Win Xp SP3 laptop * via a Symbol MC9190 Win CE 6 mobile device When roaming we notice a small hick-up less then 1 second, what is very acceptable. With the Psion NEO it's still not working, when roaming the screen freezes from 2 to 30 seconds. The RDP client on the win xp sp3 laptop and the symbol mc9190 is version 6.0. The RDP client on the neo is version 5.2. I have changed the security layer on the RDP host to RDP security layer (based on forums on the internet), because older RDP clients seem to have issues with the RDP 7.1 protocol on the Win server 2088 R2. Psion adviced us to do some network logging activity on the different devices. We made this logging via wireshark, and based on this the conclusion of Psion is that the server fails in handling tcp-requests. Can anyone give me a second opinion by analysing the wireshark loggings. Thanks in advance. Regards Patrick

    Read the article

  • hardware addressing and configurable addressing scheme

    - by Zia ur Rahman
    basically i want to ask question about configurable addressing scheme for LAN interface hardware. i have read about it from a book, some main points are given by a configurable addressing scheme provides a mechanism that a customer can use to set a physical address.The mechanism can be manual (the switches that must be set when the interface is first installed).or an electronic memory such as an EPROM that can be downloded from the computer(what does this means). Most hardware needs to be configured only once- configuration is usually done when the hardware is first installed. Question:Suppose a network administrator configures the LAN interface hardware (assigns the address) when he installs it. Now later on if he needs to change the physical address of the device can he change it? Or in this addressing scheme the hardware can only be configured once and we can not reconfigure it later on.

    Read the article

  • Is it safe to leave a broadband router running 24/7?

    - by Anirvan
    My father-in-law's ISP warned him in the strictest possible terms to physically turn off his rented Nokia Siemens C2110 PPPoE broadband router when not in use. Everyone I know leaves their broadband router on all the time, and I've never heard of any negative impacts. Is leaving a consumer broadband router running 24/7 really problematic? Is the ISP in question being ridiculously paranoid?

    Read the article

  • Using a MiFi via WDS

    - by Joril
    I have a Huawei R201 MiFi connected to the internet, and I'd like to use its internet connection even from devices that don't have WiFi, so I grabbed a wireless router I had lying around and configured WDS so that it'd connect to the MiFi, and this is working nicely (I can ping the MiFi from the router web interface). The next step was connecting my PC to the router via ethernet cable, but now I'm stuck... The PC can ping the router, but not the MiFi (they're all on the same subnet). Since the router can ping the MiFi, I guess this is some kind of routing issue? Should I get a more "flexible" router, such as one with DD-WRT maybe? Is what I'm trying to do even possible? (For the record the PC is running Lubuntu 11.10)

    Read the article

  • Network use of Gaming PC

    - by Matthew Patrick Cashatt
    Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

    Read the article

  • Spoof user agent for GoGo Inflight Internet?

    - by AndyL
    Is it possible to trick the GoGo Inflight WiFi on airlines into thinking that you have a mobile device instead of a laptop? It seems like most airlines that offer in flight wireless these days use GoGo. They offer different pricing for mobile and laptops. It seems like they are checking the browser's user agent. Out of curiosity, is it possible to use a Firefox extension like this one to spoof the user-agent and allow a laptop to access the internet under a GoGo mobile plan? How would GoGo handle something like an IMAP email client, like Thunderbird. Do IMAP clients have a user-agent field as well that would normally identify whether the mail client is running on a laptop or mobile device?

    Read the article

  • vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

    - by kce
    I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

    Read the article

  • Bandwidth Suggestion

    - by Campo
    I have been asked to analyze the bandwidth usage of a company and make a recommendation for upgrading their Internet connection(s). Here is the layout 3 DLS lines so it is 3x(6 Down, 1 Up Each) into a load balancer out to the office's network. 30 VOIP phones run on a T1 (1.5 Down, 1.5 Up) The users at the company are heavily uploading. It is my suspicion that the issue in slowdown is being cause by multiple people uploading and others not being able to get requests out for even simple http requests. My initial idea is to get them a fiber line with a 10 down and 10 up. What do others think on this plan? Will that be enough to host their network traffic? What do I do about the VOIP line afterward? The fiber is expensive and I know the T1 does a great job for their VOIP so I do not want to suggest a DSL line because I know it may not be sufficient. I would also like to save them some money if I can. Maybe even get a faster fiber line and forgo the T1. Though I know their load balance/switch can only handle 20MB/S throughput. Looking for some confirmation/suggestions on my plan. I am planning on going in to get some real diagnostic numbers. Any suggestions on software to use for that? Preferably Windows software.

    Read the article

  • Can a Linksys Router be the cause of bad speeds on a 1.5 mbps link.

    - by gramware
    We use a Linksys 5-port router at a smal organization with about 20 employees. We recently acquired a 1.5 mbps fibre link, but sometimes the link goes down and speeds are still low. On enquirey from the ISP, this was part of the response, However there maybe throttling due to the router in place. A Linksys is a low end router and may be unable to carried traffic of up to 1536Kbps. We are in a position to deploy a Cisco 871 router on test for 2 wks to eliminate that possibility. Also kindly advise the destination of the ping results they look to high. How true is that about the router throttling the network and need for a bigger one.

    Read the article

  • Airport Express with a PC

    - by Margaret Ashcraft
    I have and airport express and my IMac works fine with the internet connection, but my husband's PC in the basement has problems. The wireless connection comes and goes. One minute it says good connection the next unavailable. I have a PC laptop that will pick up the connection in the basement just fine.

    Read the article

  • How to configure 2nd network card for use in VMWare Workstation?

    - by Timo
    Hi all, I am using VMWare Workstation 6.5, connected to my network with a bridged adapter so that the virtual machine OS (Windows XP) has its own IP adress. This just worked out of the box. Now my host machine (Windows Vista) has an additional network card that is directly connected to another computer using a crossover cable (and fixed IP adress 10.1.1.4, while the "main" network connection is using DHCP with IP in the 192.68.0.* range). How can I use that network connection as well in the virtual machine? Do I need to bridge my 2nd network adapter to some VMnetX adapter? Do I need to add a host virtual adapter? I do not know much about networks, and the VMWare network settings really confuse me :-) Thanks, Timo

    Read the article

  • Does an unmanaged 4/8-port GBit Ethernet switch with a GBIC port exist?

    - by Aaron Digulla
    I'm looking for a simple unmanaged switch with 4-8 GBit Ethernet ports and a fiber port (either as a GBIC slot or pre-installed with a 1000BASE-SX port). Does something like that exist? [EDIT] I want to connect to places in my home without drilling large holes though the floors. Therefore, I'm looking for a cheap way to connect two GBit switches via fiber. I tried with a media converter (GBit <- multimode fiber) but that costs about 50% throughput. So I was hoping that there is a cheap, small GBit switch which has a GBIC slot). All I found so far are very expensive managed switches with 12 or 24 ports for industry use.

    Read the article

  • Slow download speeds on MacBook Pro

    - by Austin
    Just as the title says, I am getting very low download speeds on my MacBook Pro. I did a speed test at speedtest.net, and am getting 7 MbPS down, .5 up. However, I can only seem to get 270 KB PS max (averaging 100 K), whether on my school's network or on my home network, wired or wireless. I am on Mac OS X 10.5.8, with Google Chrome. My ethernet settings (under System Preferences - Network - Ethernet Connection - Advanced - Ethernet) are set to "Configure Automatically", "Speed: 100TX", "Duplex: full-duplex, flow-control", and "MTU: Standard (1500)". As far as I can tell, there are no throttles or anything between here and the ISP, so... Any ideas on why I'm getting such low download speeds?

    Read the article

  • racoon-tool doesn't generate full racoon.conf file in /var/lib/racoon/racoon.conf

    - by robthewolf
    I am using ipsec-tools/racoon to create my VPN. I am using racoon-tool to configure racoon.conf but when I run racoon-tool reload it only generates the first section - Global items. When I run racoon-tool I get: # racoon-tool reload Loading SAD and SPD... SAD and SPD loaded. Configuring racoon...done. This is the entire file /var/lib/racoon/racoon.conf # # Racoon configuration for Samuel # Generated on Wed Jan 5 21:31:49 2011 by racoon-tool # # # Global items # path pre_shared_key "/etc/racoon/psk.txt"; path certificate "/etc/racoon/certs"; log debug; I cannot find anywhere a solution as to why this is happening. Please help

    Read the article

  • Basic questions about network topologies

    - by laoshanlung
    I have just started learning about network topologies, but there are a lot of confusion about different types of network topologies i have learnt so far. First of all, BUS topology. If i have like 100 PCs in the same wire connected using BUS topology, and the network connection speed is 100Mbps, then each PC will have a connection of 1Mbps, right ? With the same scenario, if i connect those 100 PCs using STAR topology, then each PC will have a connection of 100Mbps ? Then with the TREE topology, i divide the system into 10 sub-system (10 tree branches) , each branch has 10 PCs, then i will have other 10 small "BUS-topology" networks each one will have a connection of 10Mbps and therefore each PC will also have 10Mbps ? And the last one is RING topology, 100 PCs, each PC will have 100Mbps connection ?

    Read the article

  • "The connection to the server was reset while the page was loading"

    - by andygeers
    I've just taken over managing the network for a small charity, and am finding internet access very flaky - we keep getting "The connection to the server was reset while the page was loading." errors (HTTP Error 12031 according to the Windows network diagnostic tool). It doesn't seem to be anything to do with our ISP since it also affects internal traffic (even requests to an Apache instance on my localhost!) Adjusting the MTU setting in the Windows XP registry sometimes seems to help for a few minutes after rebooting, but the problem always returns.

    Read the article

  • Splitting build cross the network?

    - by Dandikas
    Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

    Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >