Search Results

Search found 11914 results on 477 pages for 'networking architecture'.

Page 128/477 | < Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >

• Ubuntu 12.04 Server - eth0 1Gbps NIC eth1 10Gbps NIC - all traffic using eth0?

  - by James

  Ubuntu Server 12.04.1 x64 Primary role is an NFS fileserver, for Mac OSX Clients. Hardware: Eth0: 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Eth1: 07:00.0 Ethernet controller: MYRICOM Inc. Myri-10G Dual-Protocol NIC Config: ifconfig eth0 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.150 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:460042020 errors:0 dropped:148 overruns:0 frame:0 TX packets:231906707 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:581431978417 (581.4 GB) TX bytes:259057368617 (259.0 GB) Interrupt:20 Memory:f7d00000-f7d20000 eth1 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6832208 errors:0 dropped:2 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:513826442 (513.8 MB) TX bytes:33688 (33.6 KB) Interrupt:59 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:507 errors:0 dropped:0 overruns:0 frame:0 TX packets:507 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:45057 (45.0 KB) TX bytes:45057 (45.0 KB) nano /etc/network/interfaces #The loopback network interface auto lo iface lo inet loopback #The primary network interface auto eth0 iface eth0 inet static address 192.168.0.150 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 #second network interface auto eth1 iface eth1 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 Currently I am using on the OSX clients: nfs://192.168.0.100/Volumes/Storage to mount the NFS share. My problem is why would all the data (and I have checked using various monitoring tools bmon, iftop, glances, etc) be going over the slower connection?? Also, after configuring /etc/network/interfaces with the above setup I always get an error message at bootup something about waiting for network configuration. Are these connected?

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• TP-Link TL-WA701N not working good as wireless extender

  - by djechelon

  I bought the device in subject to extend the range of my WPA2/PSK-protected wifi network powered by a TP-Link TL-WR340G device (AP+router). I configured it as follows: Operation mode: Universal Repeater MAC of AP: scanned my SSID and got it Channel width: 20MHz Security options: the same as the parent AP (WPA2/PSK with AES encryption) After configuration inSSIDer shows me two APs beaconing the same SSID at different SNRs (because I was with my laptop close to the extender). After a few hours my tablet, far from the parent AP, stopped working. I found that the scan reported two networks with the same SSID: one WPA-protected and one free at all. This happened very frequently. Rebooting the extender by unplugging it worked but this doesn't last long. Sometimes the extender stops transmitting at all, sometimes it beacons an open network to which nobody can connect (because there is no DHCP). What's wrong with my configuration?

  Read the article

• Login configuration script for Junos EX 2200 using minicom

  - by liv2hak

  I am connecting to Junos OS on Juniper EX-2200 switches using minicom as shown below minicom -C log_sw1 sw1 Now I have a series of commands that I need to execute on sw1.(example shown below) cli request system zeroize show config show interface edit delete protocols set system arp aging-timer 240 I want to avoid having to type these commands every time I log into the system.I want to put them in a config file and I want the it to be execute every time I log into the switch using minicom. Is there any way I can achieve this?

  Read the article

• Wireless Access Point - Can't ping other machines on the wireless network

  - by Surfer513

  I have a wireless access point (Netgear), and I have it setup so that it has an IP address in the current subnet (let's say 192.168.2.0, subnet mask of 255.255.255.0). The machine that it is connected to via ethernet cable has an IP in the same subnet as the AP. The machines that are connected to the AP via the wireless connection also have an IP address in the same subnet as the rest of the network (192.168.2.0). All machines can ping the access point, but they cannot ping each other. I don't totally understand why, because there is connection and all of the machines are in the same subnet. I realize this is a layer 3 device, but is there an issue because of this AP's lack of gateway capabilities? (i.e. no routing table, etc.)

  Read the article

• iPhone Remote with iTunes Library via VPN

  - by sudo work

  Alright, so I'm currently behind a network router (not under my control). The router performs NAT and somehow prevents a computer from scanning other nodes. At least, you're unable, in this instance, to locate an iTunes library. You can, however, communicate with a node's open ports if the local IP address is known, as well as the port. I haven't actually tried port scanning a specific IP using nmap or another tool yet. So I've tried one solution to remove the contribution of the router entirely (to verify that it works without the influence of the routers). I set up an access point using my iPhone and tethered my computer (with the library) to it. From here, I was able to pair my library and the iPhone Remote application. Control of the library was normal as well. This solution is not ideal, however, because I am actively using bandwidth with my computer and cannot afford to be tethered to my 3G connection. A viable solution for me is to use a common VPN connection, which I have set up on a Ubuntu (Intrepid) server that is remote. Both my computer and iPhone are able to access the VPN via PPTP. The server is setup with PPTPD as the VPN-server; I'm using IPTables to perform IP masquerading and forwarding traffic. I however, still cannot connect the library to the phone. I can however, see both devices on the VPN subnet (192.168.0.0/24). SSH'ing and such works fine. What settings on the VPN server must I change to get this to work? Also, how can I assign static IP addresses to various PPTP clients based on MAC addresses?

  Read the article

• All the Gear and No Idea: Suggestions for re-designing my home/office/entertainment network

  - by 5arx

  Help/ Advice/ Suggestions please: I have a load of kit that I love but which currently operate in disconnected, sometimes counter-productive way. Because I never really had a masterplan I just added these things one after another and connected them up in ad hoc ways. Since I bought my Macbook I've found I spend much less time on the MacPro that was until then my main machine. Perversely, as my job involves writing .Net software, I spend a lot of Mac time actually inside a Windows 7 VM. I stream media from the HP box to the PS3 and thus to the TV, but its not without its limitations/annoyances. We listen to each other's iTunes libraries but the music files are all over the place and it would be good to know they were all safely in one location (and fully backed up). I need to come up with a strategy that will allow me to use all the kit for work, play (recording live music, making tunes, iMovie work), pushing/streaming media to the TV and sharing files with my other half (she uses a Windows laptop and her iPod touch). Ideally I'd like to be able to work on any of the machines and have a shared homedrive that was visible to all machines so all my current files were synced up wherever i was. It would be great if I could access everything securely and quickly over the web. I'd also like to be able to set up a background backup process. The kit list thus far: Apple MacPro 8GB/3x250GB RAID0 + 1TB Apple MacBook Pro 13" 8GB/250GB - I spend a lot of my work time on a Windows 7 VM on this. Crappy Acer laptop (for children's use - iPlayer, watching movies/tv files) HP Proliant Server 4GB/80GB+160GB+300GB Sun Ultra 10 2 x 80GB (old, but in top-notch condition) PS3 160GB iPod Classic 2 x 8GB iPod Touch Observations: Part of the problem is our dual use of Windows and OS X - we can't go for a pure NT style roaming profile. Because the server is also used for hosting test/beta applications and a SQL Server db, it can't be dedicated to file serving. The two Macs really could do with sharing a roaming profile or similar. I'd love to be able to do something useful with the Ultra 10. My other half has been trying to throw it away for over five years now and regularly ask what function it serves in my study :-( I've got no shortage of 500GB external USB hard drives iMovie files are very large and ideally would be processed on a RAID system. Apple's TimeMachine isn't so great. If anyone could suggest all or part of a setup that would fulfil some of my requirements I'd be very grateful. I am willing to consider purchasing one or two more bits of kit (an Apple TV and a Squeezebox have been moted by friends) if they will help make efficiencies rather than add to the chaos and confusion. Thanks for looking.

  Read the article

• 10/100 Network performing at 1.5 to 2.0 megabyte per second - is that below normal?

  - by burnt1ce

  This comes out to about 12 to 16 megabit/seond. I've read in forums that people are getting much higher speeds (ie: "40-60 Mb/s" http://forums.cnet.com/5208-7589_102-0.html?threadID=265967). I'm getting my benchmark by having a unmanged 5 port switch connected to a WRT54GS router connect. I'm sending a file from a computer connect to the WRT54GS to another computer that's connect to the unmanaged 5 port switch. Is the linkage of the switch causing this massive overhead? i doubt it. What could explain the slow down? electrical interference?

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• If Nvidia Shield can stream a game via WiFi (~150-300Mbps), where is the 1-10Gbps wired streaming?

  - by Enigma

  Facts: It is surprising and uncharacteristic that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. 150-300mbps WiFi is in no way superior to a 1000mbps+ LAN connection aside from well wireless mobility. Throughout time, (since the internet was created) wired services have **always come first yet in this particular case, the opposite seems to be true. We had wired internet first, wired audio streaming, and wired video streaming all before their wireless counterparts. Why? Largely because the wireless bandwidth was and is inferior. Even today despite being significantly better and capable of a lot more, it is still inferior to a wired connection. Situation: Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable to me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. While this secondary project will provide a wired connection, it still shouldn't be necessary to purchase a Shield to have this benefit. Not only this but Intel's WiDi claims game streaming support as well - wirelessly. Where is the wired streaming? All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I should be able to stream to my second desktop or my laptop both of which by hardware comparison are superior to the Shield. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? Reiteration of questions: Is there a technical reason (non marketing) for why Nvidia opted to bottleneck the streaming service with a wireless connection limiting the resolution to 720p and introducing intermittent video choppiness when on a wired connection one could achieve, presumably, 1080p with significantly less or zero choppiness? Is there anything limiting developers from creating a PC/Desktop application emulating the same H.264 decoding functionality that circumvents the need to get an Nvidia Shield altogether? (It is not a matter of being too cheap to support Nvidia - I have many Nvidia cards that aren't being used. One should not have to purchase specialty hardware when = hardware already exists) Same questions go for Intel Widi also. I am just utterly perplexed that there are wireless live streaming solution and yet no wired. How on earth can wireless be the goto transmission medium? Is there another solution that takes advantage of H.264 video compression allowing live streaming over a wired connection? (*) - Perhaps this isn't the first but afaik it is the first complete package. (**) - I cant back that up with hard evidence/links but someone probably could. Edit: Maybe this will be the solution I am looking for but I still find it hard to believe that they would be the first and after wireless solutions already exist. In-home Streaming You can play all your Windows and Mac games on your SteamOS machine, too. Just turn on your existing computer and run Steam as you always have - then your SteamOS machine can stream those games over your home network straight to your TV! - http://store.steampowered.com/livingroom/SteamOS/

  Read the article

• Connectivity good between VMs, but no connectivity between host and VM

  - by Greg Sansom

  I have a strange situation where connectivity (ie ping, access shared folders and services) is fine between virtual machines, but not between the host and the virtuals. I've been using Hyper-V almost every day for years and have never had a problem like this. Note the following: The host machine and all virtuals are running Windows Server 2008 r1. All machines can connect to the web, and the gateway router. Subnet mask and gateway reported in ipconfig are identical for all machines. I can access virtuals via the Hyper-V snap-in only. Doea anyone have suggestions about what might be wrong, or what diagnostic steps I can take?

  Read the article

• How do I add a broadcast IP to the loopback interface under os/x using ifconfig when my machine has no network?

  - by bandodeotarios

  I'm new to advanced network administration and I would like to do some testing with UDP broadcasting, so I need a broadcast address on my loopback interface. The machine is offline, in other words, there is no network. How can I accomplish that through ifconfig without having to buy a switch as one user in the comments suggested. In Linux all i have to do is use 127.255.255.255 and broadcasts work fine without any network or any switch. If I have a network i can just use 255.255.255.255, obviously.

  Read the article

• Resolving DNS queries for two disconnected, private, networks

  - by Mikeage

  I'm trying to setup two PCs (one Windows, one Linux, but my understanding is that this problem is more DNS and less OS) as follows: Home network: 192.168.1.0/24 VPN (via OpenVPN server not within the home network): 192.168.2.0/24 . I would like a PC on both networks to be able to access three different types of site: Internet addresses Addresses on the home network Addresses on the vpn However, I'm not sure how/which DNS servers to use. If I prioritize my home DNS server, I can resolve (1) and (2), but not (3). If I prioritize my VPN DNS server, I can't resolve addresses of type (2). Of course, looking up addresses via nslookup and explicitly setting the correct server works, so I know my local DNS servers are OK. Is there any way I can set up my PCs to fallback on the second DNS server if there is no response? Alternatively, is there any way I can tell different queries to go to different servers [maybe by setting up different subdomains; foo.local.something vs. bar.vpn.something]? Thanks

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• Determining the health of a Cisco switch port?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• How could two processes bind onto the same port?

  - by Matt Ball

  I just ran into an issue where a request made to localhost:8080 from curl was hitting a different server than the same request made from inside Node. lsof -i :8080 revealed that two processes were both binding onto the same port: COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME node 51961 mball 14u IPv4 0xd980e0df7f175e13 0t0 TCP *:http-alt (LISTEN) java 62704 mball 320u IPv6 0xd980e0df7fe08643 0t0 TCP *:http-alt (LISTEN) How is this possible? Were they binding onto different interfaces? Or was it the IPv4 vs 6? If you're curious, node was hitting the other node process, curl was hitting the java process. The java process was started after the node process.

  Read the article

• VPN Error 619: Behind Cisco Router WRT310N

  - by ty91011

  I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

  Read the article

• Internet speed is suddenly slow only on my laptop, but it's normal in other devices

  - by Wael

  I have a TP-Link router connected to a ZTE modem, with 2 laptops, a tablet, 2 phones connected via the router's WiFi, and an additional desktop connected via ethernet to the router. Today, my laptop started to have a very slow connection to the internet, which at first I thought it was the operator's problem to find out later on that it works fine on other devices. I tried to connect directly via WiFi to the modem, but it was as slow. I cannot access facebook at all, google takes forever to do a search, and youtube barely works. The weird thing though, is that when youtube does work, the streaming is full speed. This happens also when I download a file! My browse is Firefox, but I used Chrome and IE9 with the same results. I work on Windows 7 Thanks for any advices.

  Read the article

• Running a small IPTV station

  - by nixterrimus

  I'm looking to run an iptv station for my dorm. I know I can serve multicast so that's not a problem. The station will serve out podcasts and other cc licensed content. The target endpoint is xbmc- a media center. So far I know that I need to serve an rtp stream over udp that's streaming an mpeg-4 avc main or high profile with aac ( or ac3 ?) audio. I've had some luck using vlc with vlm to stream but it seems limited. What are my other options?  Everything has to run on Linux- hopefully open source. How can I use playlists and not live streams? What are my software options?

  Read the article

• Why Does Wireless Gear Degrade Over Time?

  - by bahamat

  I saw this originally posted on slashdot, but their comment format is not conducive to actually getting a correct answer. Having directly experienced this phenomenon myself, I'm now asking here where I think I can actually get an educated answer. Here's the original question verbatim: Lately I have replaced several home wireless routers because the signal strength has been found to be degraded. These devices, when new (2+ years ago) would cover an entire house. Over the years, the strength seems to decrease to a point where it might only cover one or two rooms. Of the three that I have replaced for friends, I have not found a common brand, age, etc. It just seems that after time, the signal strength decreases. I know that routers are cheap and easy to replace but I'm curious what actually causes this. I would have assumed that the components would either work or not work; we would either have a full signal or have no signal. I am not an electrical engineer and I can't find the answer online so I'm reaching out to you. Can someone explain how a transmitter can slowly go bad? Common (incorrect, but repeated) answers from slashdot include: Back then your neighbors didn't have wifi, now they do. They drowning you out. I don't think this is likely because replacing the access point with a new one and using the same frequencies solves the problem. Older devices had low transmit power. Crank that baby. As mentioned by a FreeBSD wireless developer this violates regulations and can physically damage the equipment. It was also mentioned that higher power in one direction is not necessarily reciprocated. This shows higher bars, but not necessarily a better connection. Manufacturers make cheap crap designed to wear out. This one actually may be legitimate although it is overly broad. What specifically causes damage over time? Heat? Excessive power? So can anyone provide an informed answer on this? Is there any way to fix these older access points?

  Read the article

• iptables DNS resolution

  - by Favolas

  I have a virtual machine with Fedora 19 acting as a router. This machine as an interface (p8p1) with the IP 172.16.1.254 that is connected to another machine (IP 172.16.1.1) that's simulating the external network. I've installed snort 2.9.2.2, applied the snortsam-2.9.2.2.diff.gz patch and installed snortsam 2.70 on the routermachine In snort.conf besides altering some RULE_PATH I believe I've only added the following line to the file. output alert_fwsam: 127.0.0.1:898/password After doing this two comands: ifconfig p8p1 promisc /usr/local/snort/bin/snort -v -i p8p1 If I ping from the external network to the router IP, I can see the info about the pings. One of the rules that I have is icmp-info.rules that as this single line: alert icmp $EXTERNAL_NET any -> $HOME_NET any (msg:"ICMP-INFO Echo Reply"; icode:0; itype:0; classtype:misc-activity; sid:408; rev:6;fwsam: src, 5 minutes;) snortsam.conf as this data: defaultkey password accept localhost keyinterval 30 minutes dontblock 192.168.1.1 # rede local rollbackhosts 50 rollbackthreshold 20 / 30 secs rollbacksleeptime 1 minute logfile /var/log/snort/snortsam.log loglevel 3 daemon nothreads # linha importante para gerar os bloqueios via iptables iptables p8p1 LOG bindip 127.0.0.1 Now I run this command: /usr/local/snort/bin/snort -u snort -i p8p1 -c /etc/snort/snort.conf -l /var/log/snort -Dq Terminal gives this message: Spawning daemon child... My daemon child 2080 lives... Daemon parent exiting (0) and when I runsnortsam in terminal i got this: SnortSam, v 2.70. Copyright (c) 2001-2009 Frank Knobbe . All rights reserved. Plugin 'fwsam': v 2.5, by Frank Knobbe Plugin 'fwexec': v 2.7, by Frank Knobbe Plugin 'pix': v 2.9, by Frank Knobbe Plugin 'ciscoacl': v 2.12, by Ali Basel <[email protected]> Plugin 'cisconullroute': v 2.5, by Frank Knobbe Plugin 'cisconullroute2': v 2.2, by Wouter de Jong <[email protected]> Plugin 'netscreen': v 2.10, by Frank Knobbe Plugin 'ipchains': v 2.8, by Hector A. Paterno <[email protected]> Plugin 'iptables': v 2.9, by Fabrizio Tivano <[email protected]>, Luis Marichal <[email protected]> Plugin 'ebtables': v 2.4, by Bruno Scatolin <[email protected]> Plugin 'watchguard': v 2.7, by Thomas Maier <[email protected]> Plugin 'email': v 2.12, by Frank Knobbe Plugin 'email-blocks-only': v 2.12, by Frank Knobbe Plugin 'snmpinterfacedown': v 2.3, by Ali BASEL <[email protected]> Plugin 'forward': v 2.8, by Frank Knobbe Parsing config file /etc/snortsam.conf... Linking plugin 'iptables'... Checking for existing state file "/var/db/snortsam.state". Found. Reading state file. Starting to listen for Snort alerts. and snortsam.log as an entry like this 2013/10/25, 10:15:17, -, 1, snortsam, Starting to listen for Snort alerts. Now, from the external machine I do ping 172.16.1.254 and it starts showing the info and an alert file is created in /var/log/snort/ that as the info about the PINGS. Something like: [**] [1:408:6] ICMP-INFO Echo Reply [**] [Classification: Misc activity] [Priority: 3] 10/25-10:35:16.061319 172.16.1.254 -> 172.16.1.1 ICMP TTL:64 TOS:0x0 ID:38720 IpLen:20 DgmLen:84 Type:0 Code:0 ID:1389 Seq:1 ECHO REPLY Also, if I run instead /usr/local/snort/bin/snort snort -v -i p8p1 i got this message: Running in packet dump mode --== Initializing Snort ==-- Initializing Output Plugins! Snort BPF option: snort pcap DAQ configured to passive. The DAQ version does not support reload. Acquiring network traffic from "p8p1". ERROR: Can't set DAQ BPF filter to 'snort' (pcap_daq_set_filter: pcap_compile: syntax error)! Fatal Error, Quitting.. So, this are my questions: Shouldn't snortsam block the PING? Is that DAQ error causing the problem? If so, How can I solve it?

  Read the article

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• ESXi 4.1 CentOS 6.X eth0 unnavailable

  - by L.K.

  I don't usually ask for help so directly, usually google have all i need but this time i'm seriously lost. Hope you can help me .s The thing is, i have a server with Vmware ESXi 4.1 and 5 already running and configured virtual servers, but whenever i try to make a new one on CentOS 6.X it leaves me without eth0 to be activated in any way. When installing CentOS, in the screen of localhost.localdomain i try by the button in the left down corner of the screen to make eth0 connect automatically but it tells me a NetworkManager Error: cannot start eth0. So...in command line once the CentOS is already installed, i have configured ifcfg-eth0 and manually tried to take up the eth0 but when i restart network service "Bringing up eth0: Failed" and sometimes even "shutting down eth0: Failed" Thanks in advance

  Read the article

< Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >