Search Results

Search found 29898 results on 1196 pages for 'go minimal'.

Page 129/1196 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• How do I put back different SCSI hard drives into their original RAID arrays across different servers?

  - by Edgar

  I have potentially a big mess in my hands: I received today a box with several hard drives that used to be connected to different servers each one of them using an unknown - at least as of right now- RAID configuration. Regretfully, these are not marked and I'm not sure how to go about putting them back into their original servers. Currently I don't have much more information: I don't know what type of array was being used on each instance and I don't have any specifics about the RAID controller originally used on each one of the servers (currently these servers are at a remote location with no easy access). Is there a way to sort through this mess? What would be the consequences of using trial and error to go about it? This might be a very basic question but I don't have much experience dealing with RAID arrays.

  Read the article

• How to change internal page numbers in the meta data of a PDF?

  - by YGA

  I have a pdf document I created through non-Acrobat means (printing to pdf, then merging a bunch of pdfs), but I'd like to manually change the page numbers (i.e. the first several pages are simply title pages, the page that is labeled "page 1" is really the 7th sheet of the pdf). What's the simplest (and ideally, free) way to do this? To be clear, I am not trying to change the numbers on the pages themselves, but the page numbers in the "metadata" that the pdf stores (the pages themselves are already numbered correctly; I just want "go to page 1" to go to the page labeled 1, which could be sheet 7). For what it's worth, I'm on Windows, though I have access to Macs as well.

  Read the article

• oracle virtualbox doesn't work for host Kubuntu since Lucid Lynx 10.04

  - by 13east

  I have a thinkpad edge 14 core i3 2.4 ghz and 4g ram; I have tried kubuntu 10.04, 10.10, 11.10, 12.04 and 12.10 (all x64 architecture); Both oracle and ose virtualbox only works properly to install XP and windows 7 quest system on kubuntu 10.04; For every other kubuntu release since, the guest installation goes as far as formatting the virtual drive, freezes at this step, and doesn't even go as far as copying files to hard-drive to begin installation. But virtualbox has not stopped responding to commands; I can kill that one specific window with the problem installation ("machine" - "close" - "power off the machine") and start over again without having to force-kill virtualbox application. If anyone knows how I can go about addressing this problem, any help you can provide would be very much appreciated. Thank You.

  Read the article

• Dropping duplicate|redundant Unique Constraint from FILESTREAM table

  - by electricsk8

  I have a table with a FILESTREAM column, and it has two unique constraints specified for the same FILESTREAM column, ie: ALTER TABLE [dbo].[TableName] ADD CONSTRAINT [UQ_TableName_33C4988760FC61CA] UNIQUE NONCLUSTERED ([GUID_Column]); GO ALTER TABLE [dbo].[TableName] ADD CONSTRAINT [UQ_TableName_33C49887145C0A3F] UNIQUE NONCLUSTERED ([GUID_Column]); GO I'd like to drop one of the unique constraints, as they are duplicates. However, when I try and drop one of the two duplicate constraints, I receive the following error. "A table with FILESTREAM column(s) must have a non-NULL unique ROWGUID column." Anyone know how to remove one of the two constraints?

  Read the article

• Dell 2155cdn Multifuntion Printer

  - by Wayne-Z

  Hey guys. So after a prolonged period, (overnight) i lose the ability to initiate a scan directly from the unit. I'll initiate a job and after awhile, it times out and beeps. However, when i go to the PC and initiate a scan from there, the scan job goes through just fine, and i can then initiate scans directly from the unit all day. Until a prolonged period (overnight). Then i have to do the process again. Ive made sure all powersave settings were off.. The PC doesnt go to sleep or a powersave state. Any insight into this will be appreciated. Pertinent Info: - Unit: Dell 2155cdn Multifunction - Connected via USB - PC: Dell Optiplex 755

  Read the article

• Dlink search is hijacking my browser

  - by James

  For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

  Read the article

• HD Radeon 6950 cannot run multiple monitors

  - by Bryan S.

  I'm having troubles getting multiple monitors to run on my graphics card. I plug one via the hdmi, and one into the DVI (I have tried both available DVI ports). with one DVI port it does not even register the monitor, with the second one I go into the Catalyst Control Center and it gives me the option to swap between the HDMI and the DVI port. I guess since this is the flex edition I could just go get 2 DSP to HDMI converters, plug 2 monitors in through the available DSP, and than the 3rd one into the HDMI, but do you have any idea why it will not let me run one HDMI and one DVI?

  Read the article

• Domain redirection to port on Windows Server 2008

  - by Rauffle

  I have a Windows server running IIS. I wish to run a piece of software that hosts a web interface on a non-standard HTTP port (let's say, port 9999). I have static DNS entries on my router for two FQDNs, both of which direct to the Windows server. I wish to have requests to 'website1' to continue to go to the IIS website on port 80, but requests for 'website2' to instead go to port 9999 to be handled by the other application. How can I accomplish this? Right now I can get to the application by going to 'website1:9999' or 'website2:9999'.

  Read the article

• Navigate to a virtual member from an overriden member in the derived type

  - by axrwkr

  Using visual studio, in the editor window, I am able to navigate from the usage of a member to the line and file where it is declared by pressing F12 while the cursor is over that member by or right clicking on the member and selecting "Go To Definition". I would like to find a way to navigate from an override member to the base class member that it overrides. For example, if I have the following class with one method public class SomeClass { public virtual void TheMethod() { // do something } } An I override that method somewhere else in the project or solution similar to the following public OtherClass : SomeClass { public override void TheMethod() { // do something else } } I want to navigate from the declaration of TheMethod in OtherClass to the declaration of TheMethod in SomeClass Is there a way to do this? I've found that I can find the definition of the member in the base class by pressing Shift + F12 (Find all References) and then looking through the list occurances, this works fine most of the time, since the list isn't usually that long but it would be much better to have a way to go there directly.

  Read the article

• Debian PPTP VPN can't get out to the internet

  - by phidah

  I've setup a Debian pptp server which seems to be running fine. I can successfully access the local services on the server when connected to the VPN, but I cannot go out of the LAN, i.e. I cannot just go to any server out on the internet. I guess this is come kind of routing issue that won't allow me to use the server as a gateway? I couldn't really find any articles or similar that could tell me how to set this up properly. Thanks in advance.

  Read the article

• Empty Recycle Bin error "Cannot Delete Dc12: Access denied."

  - by Chris Noe

  The Dc number can vary. The error is a sporadic, but when it happens it prevents the contents of the recycle bin from being deleted. It can also occur when the recycle bin appears to be empty, yet it has the crumpled paper indicator. Rebooting makes the problem go away, but it can also magically go away by just waiting a long time, like over night. But the problem keeps recurring with no rhyme or reason. What is causing this? I really don't want to reinstall Windows.

  Read the article

• Cross domain LDAP

  - by Adam

  For a system we are developing we have 2 domains an internal and an external domain with bi directional trust between them. However the servers are only able to connect to their own DC's. We have an application server on the internal domain which needs to use an LDAP query to gather a list of users from a group on the external domain. How do i go about writing an LDAP query that asks one DC to go ask another DC for a list of users. I tried querying the internal DC with the same LDAP query I would use if it could hit the external DC directly but this does not work. When i use Softerra LDAP Administraor I can view the full hierarchy of the interal domain but despite the trust relationship between domains i am unable to see any of the external doamin. Any suggestions or help would be greatly appreciated

  Read the article

• Mouse Error Code 24. Windows 7

  - by Cj.

  I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

  Read the article

• Generic Sample Terms and Conditions for a Website

  - by Tyler

  I want just a very simple and very generic terms and conditions sample to go off of, anyone have any links? Thanks SU

  Read the article

• upgrading ram to something faster

  - by Mike

  Im going to be adding more ram to a desktop is it poss to go from ddr2 667mhz pc2-5300 to something faster

  Read the article

• Replacing old server with new but different hostname & same IP

  - by MaxFr

  We have an old server 2000 and lots of users point to it by hostname and by its IP e.g \\server1, we have a new server 2008 R2 with new name serverlocation1 All folders and data have been sync'toy'd from the old server1 across to serverlocation1 each evening, the new server tree is exactly the same on the new server and all perms are correct. We need to make the new server the same IP as the old server1 as too many people access it directly via IP, and to ensure file and folder paths stay ok, anything \\server1\folder\file needs to go to \\newserverlocation1\folder\file etc I can change the old server1 name to server1-old & change IP and assign the old IP to the new server, but how do I force anything coming in for \\server1 to go to the new server and ensure anything referenced to the old server goes onto the new server ? I can CNAME but I need the new server to have the IP of the previous server so not sure if its straight forward etc..... point server1 to newserverlocation1 Then probably change DNS so that the OLD IP points to new hostname..... Any clarification appreciated.

  Read the article

• What motherboard for a Core i7 920 Processor?

  - by jasondavis

  I am wanting to build a really nice PC, price is not to important as I will buy pieces every week or whatever it takes until I get everything I need. I am not a gamer but I would like to watch video and have 3-4 monitors. I do a lot of programming and use a lot of big programs so I would like to go all out and get a lot of Memory, probably at least 12gb but possibly more even as I see many boards support up to 24gb now. Will be using Windows 7. I have decided to go with the Core i7 920 Processor BX80601920. Based on what I posted above, can you please recommend some good motherboards I should look at ? Also some good places to purchase them online. Thanks for any help, tips, etc.

  Read the article

• Both screens always stay on after adding second monitor

  - by J.Merrill

  I had a single 1920x1080 monitor on a Windows 7 desktop PC and, per "power management" (not screen saver), the screen would go blank after 10 minutes. I added another monitor (2560x1600 if that matters) and since then, neither screen has ever blanked. I've tried turning on the "blank" screen saver, but that didn't help either -- I can go away for hours and when I come back, both screens are on. I've seen others with similar issues apparently caused by e.g. wireless mice that seem to move infinitesimally, but I've got the same wired mouse I had before. I can't understand why neither the screen saver nor power management is doing what it should to blank the screens, when "power management" used to do it when there was only one monitor. Maybe it doesn't matter so much with current LCD display technology (no "burn in") but doesn't a monitor use more power when "power management" hasn't turned off the display? Thanks for any suggestions.

  Read the article

• spontaneous hard disk password

  - by sc

  I had an HP proliant server go down recently. All of the sudden the sas controller (e200i) would not see any of the physical disks. New disks were detected just fine. I thought it was odd that all 6 disks would go down at one time so sent them to a data recovery firm to find out what happened. I'm being told that, somehow, all of the disks were spontaneously password protected. These are Hitachi 2.5" drives and I guess this is something of a known issue. The company has worked for a while to try and recover them, with no luck. Has anyone had experience with this? Any recommendations for how to recover the drives or a company that might have the expertise to do so?

  Read the article

• Ranking tables from Excel data

  - by Joe

  Hi all (asking here because this meta question told me to). I have some data in an excel spreadsheet here. It's no more than a table with about five columns. Year Purchased Manufacturer Model Num Unit Price Total Price 2007 SMARTBOX FuturePad XP 1 £2,915.00 £2,915.00 2007 Attainment Company Inc Go Talk 9+ 1 £104.00 £104.00 2007 Attainment Company Inc Go Talk 20+ 1 £114.00 £114.00 I'd like to be able to build a 'top ten' of either manufacturers or models (and I'd like to be able to do it by either most mentioned, most sales, or highest value of sales) - but I've got no idea what the best method is in excel. Any suggestions...? The ideal output might be a set of sells that says something like Company Units A 5342 B 232 C 2 D 1

  Read the article

• WLC 4400. Get IP

  - by Edward Connelly

  I have three SSID. one is a guest network and I'm having problems with lease times. Its set for web authentication so it passes IPs out even if someone doesn't try and authenticate. Is there a way to get that IP back and not hand another to that mac for a period of time? Poor planning and we didn't allocate enough address space, and we are sandwitched. We could go with another address, but we would have to reconfig lots. since its guest its vlan'd with no access to anthing but the firewalls. would have to change ACLs and routes and interfaces. if it isn't possible we will just have to go that route, just thought there might be an easier solution. session timeout is enabled with 1 hr lease time is set to 4 hrs. no helper DHCP and internal DHCP is set with the space split across three WLCs (60 waps split across those as well).

  Read the article

• How to uploads to the web work on local networks

  - by Saif Bechan

  Let's say I have two computers hooked up as a home network. They both use the same router, and the router is hooked up to the to the net. Now lets say I am working on computer A, and I can access files on computer B. Computer A has a drive that is mounted on computer A as a network drive. Now I want to upload a file to a website. In the browser of computer A I open a browser, and go the website. On the website I select 'upload file', now in the file browser I go to the network drive, and select a file on computer B to upload. What happens in this case. Is the file uploaded directly from computer B to the website, or is the file first transferred to computer A, and then to the website.

  Read the article

• Table Formatting in Excel 2007: How do I remove it?

  - by RocketGoal

  I've used the new Table Formatting option in Excel 2007. Now I can't remove it. I've dragged the little blue square up to the last cell on the top left, but it just won't go any further. In fact it just won't go at all. Clear all doesn't remove it. What does? I want my table back! I'm not a beginner with Excel, but this little annoyance has made me feel like on. Surely there must be some way to remove table format without deleting something or clearing all! Thanks Mike

  Read the article

• Which PSU should one chose? The biggest is the best?

  - by Shiki

  I'm fully aware of PSU's "Active PFC" and that they won't consume the written W all the time. (Makes sense). But now I'm before a PSU replacement (Guys: NEVER buy a Chieftec. Seriously.) The question is: If one can get a bigger one (in my case 750W and 650W) ... should that person go for the bigger one ? (The difference in price is not much). No, I don't think I'll soon use all that much. (Please help (if you want of course) to make the question more generic if the question is really not OK in this form. I've been wondering about this for a time already. In my case it would be XFX Black Edition Silver 750W and 650W) (Basically about "which one" I would go with XFX/Antec/something which comes with industry qualified parts. Like Duracell but in a PSU. :) But the performance is a different thing.)

  Read the article

• Can I set Windows default second-monitor behaviour to "Extend these displays"?

  - by MT_Head

  I travel to multiple offices (and multiple desks in those offices), and whenever possible I plug an external monitor into my laptop. Whenever I plug in a monitor I haven't used before, Windows defaults to "Duplicate these displays" - which messes up the arrangement of icons on my desktop if the external monitor is a different shape from my laptop's monitor. I then select "Extend these displays", and my laptop screen returns to its original shape - but my icons don't go back to their original arrangement. Grrrrr. Fast-forward a few days or weeks; I've got my icons arranged so I can find stuff again - then I go to a new office and it starts all over again. I'm tired of this. Is it possible to make "Extend these displays" the default behavior? I'm using Windows 8 x64 Home Premium, but I had the same complaint under Windows 7 x64 Ultimate. (Prior to that, I hadn't discovered the joy of dual displays. Ah, the time I wasted...)

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >