Search Results

Search found 12264 results on 491 pages for 'drive letter'.

Page 130/491 | < Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >

  • Brand new Seagate HDD has high raw read error rate

    - by kpax
    I've just purchased a brand new Seagate ST31000524AS 1TB HDD. Manufacture date shows as January 2012 (yes that's as new as new can get), so must be one of the new batches from the post-flood Thailand. Anyway, I downloaded a copy of Active Hard Disk Monitor tool to check the S.M.A.R.T. parameters and I find the parameter Raw Read Error Rate is very low. Should I be worried? Will this rectify over time? This hdd is just 7 hours old; what gives? Edit: I meant high raw read error rate - Title updated accordingly

    Read the article

  • Install Windows 8 Apps to custom directory

    - by Timothy Ford
    I'm running Windows 8 Pro on a laptop. I initially installed the OS just to fiddle round with it and get to know something I'd inevitably end up having to fix for someone. The problem being I only gave the partition about 32gb and that ran out pretty quick. I'd like to install office and get used to that as well but unfortunately I'm a few gigabytes short. I'd like to know if I can change the install location of office 2013 and other apps so that I can run them from another partition because there is no space left to the right of this partition I can't extend it.

    Read the article

  • How to find out which app locks a given USB storage device?

    - by Dimitri C.
    I'd like to unplug my USB mass storage device, but I get the following error message from Windows: Windows can't stop your 'XYZ' device because it is in use. Close any programs or windows that might be using the device, and then try again later. How can I find out which application locks the device, so I can safely unplug it without having to close all running applications first? Note: I'm working on a Windows Vista system.

    Read the article

  • Is it wise to use SSHDs (Solid state hybrid drives) on a server?

    - by Seb
    I have a bunch of servers with very heavy I/O that currently use SATA3/SAS drives, but do suffer from I/O wait on the SATA drives, and I have just been alerted to the existence of SSHDs which cost the same for 1TB as the 1TB SATA drives that we currently use. However, previously (until Seagate shipped their first 3.5" SSHD in March) they seemed to be exclusively for Netbooks/Notebooks, which leads me to suspect they're not exactly built for the heavy I/O they'd be in for with my servers. So, would an SSHD give me a performance boost over my SATA3 drives in a heavy I/O environment (such as multiple very large high speed file transfers) or is it best to stick with SATA3 with I/O wait??

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • Dual boot: Windows XP and Ubuntu

    - by user19455
    (I know that there are some questions similar to this one, but the ones I have read (and I have read more than one, did not answer my question) I have installed, in two physically different hard drives Windows XP and Ubuntu 9.0. I would like to have a dual boot that, if nothing was pressed, the Windows XP would start automatically. I have read about Grub but got the impression that it wasn't possible to default the operating system to start to something other than Ubuntu. Thanks.

    Read the article

  • Is there a limit on the number of USB external drives?

    - by Beska
    I've got three external HDDs, all My Books, 500 GB, 750 GB, and 1 TB. If I hook one or two of them up to a computer, everything seems fine. If I hook all three of them to a computer (I've tried this on two different computers, one running Windows XP, one running Windows Vista), the bootup time goes up by more than an order of magnitude. It can suddenly take about 10-20 minutes to boot the machine, whereas before it might take a minute. All three drives work fine on their own. I'm not using any kind of hub; all three are plugged directly into the machine. Is this associated with some kind of inherent limit in USB? Is this bad hardware design in the CPU box? Is this a My Book problem?

    Read the article

  • Win7 'locking' process/files/folders?

    - by Dynde
    I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

    Read the article

  • Windows 8.1 - Why are there multiple recovery partitions in the system?

    - by Abhiram
    DISKPART> list partition Partition ### Type Size Offset ------------- ---------------- ------- ------- Partition 1 System 500 MB 1024 KB Partition 2 OEM 40 MB 501 MB Partition 3 Reserved 128 MB 541 MB Partition 4 Recovery 490 MB 669 MB Partition 5 Primary 920 GB 1159 MB Partition 6 Recovery 350 MB 921 GB Partition 7 Recovery 9 GB 921 GB Above is the list of partitions on my system that I recently upgraded to Windows 8.1. Why are there multiple recovery partitions (4,6,7)? Shouldn't there be just one recovery partition? And what is the Reserved partition (#3) for?

    Read the article

  • Cancelled a format using diskpart at 0%. Can I get the data back?

    - by Sudarshan
    I wanted to format my USB thumbdrive, but incorrectly did the following on my external HDD!! CMD -- Diskpart select disk 2 clean create partition primary select partition 1 active format fs=fat32 While it was still at 0% however, I cancelled the format and quit from CMD. I can no longer see the HDD in My computer though, and it shows up as below in diskpart Disk 1 Status - Online Size- 1800 GB Free - 0B Is there anything I can do to get the data and HDD back?

    Read the article

  • Is it possible to trick iTunes treating an external HD as an iPod?

    - by Boris Pavlovic
    I keep my music collection on my iPod, but since I got my first iPhone two and a half years ago I have quit using the iPod as a portable music device. It's just an external HD. Benefit of having it as an external HD is that when it's connected to some other computer iTunes can play its music and update iTunes database. It would be nice if I could copy data from the iPod to an external USB HD and give away the iPod to somebody who doesn't have one.

    Read the article

  • Raid recovery in gigabyte GA-8I945 Pro

    - by epeleg
    This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

    Read the article

  • Recover data from a Windows Dynamic Volume Spanned Disk

    - by iCe
    I have a dynamic volume created with two spanned partitions over two disk. Recently, one disk has started failing, and I want to copy the data inside that disk to another disk, before replacing it. However I don't know how to select only what is inside the failing disk, because the partitions spans across both disks. Maybe imaging the entire disk should do the work? Or I have to copy all the data from both disks? Thanks in advance!

    Read the article

  • end_request: I/O error, dev sda, sector xxxxxxxxx

    - by muruga
    I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. After that I am getting the following error message in kern.log and demsg kernel: [65896.678870] end_request: I/O error, dev sda, sector 17430271 kernel: [69263.783957] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK : [69263.783957] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] kernel: [69263.783957] sd 0:0:0:0: [sda] Add. Sense: Internal target failure Whether it is kernel problem or hard disk problem or Raid problem

    Read the article

  • Would an array of SSD drives be able to succesfully substitute the system memory?

    - by Florin Mircea
    I watched a few videos trying to answer this. This video (youtube.com/watch?v=eULFf6F5Ri8) shows a bunch of guys stacking 24 SSD's reaching a peak of around 2GBps r/w. That's under the limit of the worst DDR3 in this list (memorybenchmark.net/write_ddr3_amd.html) - that shows DDR3 memory performance varying from 2.78 to 6.55 Gb per second, but that video is over 3 years old. This video (youtube.com/watch?v=27GmBzQWwP0) shows a more optimistic situation, but for PCI-E SSD drives: 5 drives peaking at around 4Gb. And this other video shows that stacking up more than 3 SSD's doesn't realistically offer a substantial added performance. This and the fact that in all benchmarks the drives act quite poorly when dealing with small files (5k file read/write averaging from 10MB to around 30-40MBps) as opposed to how native memory handles such files, seems to indicate a definite NO to this question. Also, the write life cycle is indeed limited and the drives might wear out quickly, as kindly pointed out by paddy. However, I wanted to get more opinions on this. Would it be possible to at least obtain current memory performance with SSD's in RAID 0? And if so, in what circumstances? I am assuming using this configuration with a Windows OS that has a memory pagefile resident to that stack of SSD's, thus making it very fast to work with.

    Read the article

  • How can I retrieve data from a Western Digital Passport External Disk which is not getting recognized but getting shown as healthy in Device manager

    - by Rabimba Karanjai
    When I plug in this external harddisk It is not getting shown in the My Computer. But it gets shown perfectly well in the Device Manager When I go into the Computer Administrative panel and into the disk manager it asks me to initialize the disk Now when I try to initialize it, regardless of the method I try it shows me an error "Incorrect Function" As you can see windows tells me it is working properly. Is there anyway I can retrieve data from this?/access it? I have googled and it seems to be a frequent problem with WD drives. Anyone has any solutions on how I can get the data back?

    Read the article

  • DVD RW: Are they still relevant for backups?

    - by Harry
    Hello, With the availability of compact USB memory sticks with much, MUCH higher storage capacities is there still any use-case for taking periodic, incremental backups on DVD/RWs? The DVD/RW has an additional annoyance that you cannot drag and drop files to it as easily as you can on a USB memory stick. So, if I have a 4.7GB DVD/RW, I must re-burn the whole image every time I backup new stuff... with possibly rearranged file/folder structure. Secondly, why in this day and age you cannot install a file-system (like ext3 or FAT32) on a DVD/RW... and likewise on CD/RW's as you can on a USB memory stick? Many thanks, /HS

    Read the article

  • DVD RW: Are they still relevant for backups?

    - by Harry
    Hello, With the availability of compact USB memory sticks with much, MUCH higher storage capacities is there still any use-case for taking periodic, incremental backups on DVD/RWs? The DVD/RW has an additional annoyance that you cannot drag and drop files to it as easily as you can on a USB memory stick. So, if I have a 4.7GB DVD/RW, I must re-burn the whole image every time I backup new stuff... with possibly rearranged file/folder structure. Secondly, why in this day and age you cannot install a file-system (like ext3 or FAT32) on a DVD/RW... and likewise on CD/RW's as you can on a USB memory stick? Many thanks, /HS

    Read the article

  • Tool to test USB sticks?

    - by Tony_Henrich
    Some of the files I copy to a USB stick seems to be corrupted? Maybe the stick is bad but I haven't used it much and want to know for sure. Is there a Windows utility to test the stick? Mark bad areas as bad so the file system doesn't save to them? I format before I copy but I still get corrupted files? Does chkdsk work on USB sticks reliably?

    Read the article

  • How can I set deadline as the I/O scheduler for USB Flash devices by using udev rules?

    - by ????
    I have set CFQ as the default I/O scheduler. I often get bad performance when I write data into a Flash device. This is resolved if I use deadline as the I/O scheduler for USB Flash devices. I can't always change the scheduler manually, right? I think writing udev rules is a good idea. Can someone please write rules for me? I want: When I plug in a USB device, detect the type of the device. If it is a portable USB hard disk, do nothing (I think if a device has more than one partitions, it always a portable hard disk. If it is a USB Flash device, set deadline as it's scheduler.

    Read the article

  • Pendrive not working on USB port - USB2 Enhanced Host Controller - 27CC

    - by user1664417
    I have a situation here, is kind of weird. Situation as below: If i enable the 'Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC' , then my pc will not be able to read any USB stick/pendrive, but usb port work fine with keyboard and mouse. If I disable the device driver, then all kind of pendrive can be read. Below is What i have done : 1) try the same pendrive on other pc, it work like charm. 2) try others pendrive on issue pc, same problem, but it work fine in others pc. 3) try all the port, including the port that connected to mouse n keyboard. 4) update the driver version. 5) restore default setting of usb in bios Please help to solve these issue if anyone experience it before. Many thanks.. :

    Read the article

< Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >