Search Results

Search found 7517 results on 301 pages for 'fast debugger'.

Page 133/301 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• How does a hard drive compare to Flash memory working as a hard drive in terms of speed?

  - by Jian Lin

  Some experiment I did with hard drive read/write speed was 10MB/s write and 40MB/s read, and with a USB Flash drive, it can be 5MB/s write and 10MB/s read. Also, if I put a virtual hard drive .vhd file in a hard drive or in a USB Flash drive and try a Virtual Machine using it, the one using the hard drive is quite fast, while the one using the USB Flash drive is close to not usable. So I wonder some early netbooks use 4GB or 8GB flash memory as the hard drive, and even the Apple Mac Air has an option of using flash memory instead of a hard drive. But in those situation, will the speed be slower than using a hard drive, like in the case of a USB Flash drive?

  Read the article

• Textbox OnTextChanged and Button Click Event Not Firing

  - by goodwince

  I have textboxes being generated by a repeater that use OnTextChanged with autopostback enabled so that I can know when when the values change. This all works perfect. The problem starts when I try to click on any buttons on the page. The loss of focus triggers the event for the OnTextChanged; however, the event for my buttons never get fired. I checked this in the debugger and while debugging if I put a break-point in the page_load it will call both; however, without the break-point it still only calls the OnTextChanged event. I found this post on JavaScript. If my problem is also JavaScript related, why does the clicking of the button fire in debug mode? Thanks.

  Read the article

• NServiceBus FullDuplex sample compiled and debugging against .NET 4.0 framework throws exception

  - by Jim

  I just installed VS2010 RC and launched the FullDuplex sample from NServiceBus 2.0.0.1145 and it ran fine. I then changed the target framework of each project in the solution to ".NET Framework 4", recompiled and launched in the debugger and received the following exception: System.InvalidOperationException was unhandled Message=No endpoint configuration found in scanned assemblies. This usually happens when NServiceBus fails to load your assembly contaning IConfigureThisEndpoint. Try specifying the type explicitly in the NServiceBus.Host.exe.config using the appsetting key: EndpointConfigurationTypeScanned path: C:\Development\Personal\ThirdParty\NServiceBus\samples\FullDuplex\MyClient\bin\Debug\ Source=NServiceBus.Host StackTrace: at NServiceBus.Host.Program.ValidateEndpoints(IEnumerable`1 endpointConfigurationTypes) in d:\BuildAgent-02\work\672d81652eaca4e1\src\host\NServiceBus.Host\Program.cs:line 189 at NServiceBus.Host.Program.GetEndpointConfigurationType() in d:\BuildAgent-02\work\672d81652eaca4e1\src\host\NServiceBus.Host\Program.cs:line 171 at NServiceBus.Host.Program.Main(String[] args) in d:\BuildAgent-02\work\672d81652eaca4e1\src\host\NServiceBus.Host\Program.cs:line 32 InnerException:

  Read the article

• Remote Desktop doesn't lock remote PC.

  - by Jeremy Luce

  I regularly use RDP to connect to my home computer (WinXP Pro SP3) from work (WinXP Pro SP3). My home computer has multiple users set up with Fast User Switching enabled. The problem is that my wife and kids are able to log in while I'm connected via RDP. There's nothing on the login screen to indicate that I'm logged in, much less a lock of some kind that prevents them from logging in. So, is there something I can do to actually lock them out while I'm connected, or at least indicate that I'm logged in?

  Read the article

• Column cannot be added because its CellType property is null exception

  - by niko

  Hi, I have trouble with the following piece of code. When I go through with the debugger I get an exception when it comes to the following line: dgvCalls.Columns.Insert(1, msisnnColumn); I get an exception: Column cannot be added because its CellType property is null. Oddly, I created the same procedure for some other DataGridViews and it worked fine. if (!(dgvCalls.Columns.Contains("DirectionImage"))) { directionIconColumn = new DataGridViewImageColumn(); directionIconColumn.Name = "DirectionImage"; directionIconColumn.HeaderText = ""; dgvCalls.Columns.Insert(0, directionIconColumn); directionIconColumn.CellTemplate = new DataGridViewImageCell(); } if (!(dgvCalls.Columns.Contains("msisndColumn"))) { msisnnColumn = new DataGridViewColumn(); msisnnColumn.Name = "msisndColumn"; msisnnColumn.HeaderText = "Klic"; dgvCalls.Columns.Insert(1, msisnnColumn); msisnnColumn.CellTemplate = new DataGridViewTextBoxCell(); } Any suggestions?

  Read the article

• Using C# WATIN, how do I get the value of a INPUT tag html element?

  - by djangofan

  Using C# WATIN, how do I get the value of the second occurence of a INPUT tag html element on a page? I've tried a whole bunch of things and haven't succeeded. The debugger isn't giving me any obvious way to get element[1] among the 4 that returned. Console.WriteLine(ie.Element(Find.ByClass("myclass")).GetAttributeValue("value") ) ; // works but prints the value of the 1st of 4 input elements on the page Console.WriteLine(ie.ElementsWithTag("input", "text").Length.ToString() ); // returns the number 4 Console.WriteLine( ie.Element(Find.ByName("login")).GetAttributeValue("value") ); // works but its not safe since its possible there might be two elements with the name login Basically, I want to be able to select the input element by its array index.

  Read the article

• Best software for taking math notes at lectures

  - by data_jepp

  Let me first just say that I know about La-Tex, and that doesn't fast enough. I use it for papers, but for "real-time" note taking it's just to heavy. I'm talking two math classes this semester. Linear algebra and discrete math, I just got a laptop with 10 hour battery life which makes me want to take notes on it!!! Openoffice with formula thingy is what I use now. Now I have to pay attention lol. Thanks.

  Read the article

• Remote desktop is slow when connecting to a computer which is part of a domain

  - by Peuge

  Hey all, We have two windows 2003 machines, one is a DC and another is joined to the domain of the DC. These machines are not locally available to us so we have to remote desktop into them. When we first got the machines remote desktop was blazing as the machines are only a couple of miles away. I then installed AD and setup routing and remote access, I also setup DNS on the DC. Now when I try remote Desktop into the machine which is part of the domain (not the DC) it is painfully slow! Remote Desktop onto the DC is also noticeably slower! Another problem is that our FTP to the DC has also become slow. I don't know what other information I can provide, as I am new to Sys Admin (moving over from development). The speed should be fast as these machines are only a couple of miles away. Any help / suggestions is greatly appreciated! Thanks Peuge

  Read the article

• VMFS recovery - how do you proceed?

  - by ToreTrygg

  The more I look into ESX the more often i have to handle cases where the partition table of a disk with a VMFS volume gets corrupted. The reasons for this can be * idiot user * failed update * power failure * .... I guess you guys must already have something like a usual procedure on how to work through this cases. I am especially interested in a straight fast way to find out if the VMFS volume itself is corrupted beyond repair. So far I use very time consuming attempts with scans with Testdisk and similar tools. Do you have better / faster ways ?

  Read the article

• How To AutoScroll a DataGridView during Drag and Drop

  - by Mason

  One of the forms in my C# .NET application has multiple DataGridViews that implement drag and drop to move the rows around. The drag and drop mostly works right, but I've been having a hard time getting the DataGridViews to AutoScroll - when a row is dragged near the top or bottom of the box, to scroll it in that direction. So far, I've tried implementing a version of this solution. I have a ScrollingGridView class inheriting from DataGridView that implements the described timer, and according to the debugger, the timer is firing appropriately, but the timer code: SendMessage(Handle, WM_VSCROLL, (IntPtr)scrollDirectionInt, IntPtr.Zero); doesn't do anything as far as I can tell, possibly because I have multiple DataGridViews in the form. I also tried modifying the AutoScrollOffset property, but that didn't do anything either. Investigation of the DataGridView and ScrollBar classes doesn't seem to suggest any other commands or functions that will actually make the DataGridView scroll. Can anyone help me with a function that will actually scroll the DataGridView, or some other way to solve the problem?

  Read the article

• Accessing ImageButton Contents

  - by Bill

  I am representing a Solar-System's planets with ImageButtons that show the planet's image on the surface of the button, and hold the planet's important data.. name, distance from sun, etc within an instance of a Planet class, stored within the ImageButton.Content property. When the ImageButton is selected, I am attempting to access and display the Planet class's data for the selected Planet. Although ((ImageButton)e.OriginalSource).Content permits viewing all of the Planet class's properties in the debugger, I haven't figured out how to access the Planet class properties directly, as in Pluto.DistanceFromTheSun? Is it possible to access the Planet class information held in the ImageButton contents directly?

  Read the article

• GlusterFS vs Ceph, which is better for production use for the moment?

  - by Mickey Shine

  I am evaluating GlusterFS and Ceph, seems Gluster is FUSE based which means it may be not as fast as Ceph. But looks like Gluster got a very friendly control panel and is ease to use. Ceph was merged into linux kernel a few days ago and this indicates that it has much more potential energy and may be a good choice in the future. I am wondering which(even out of the two?) is a better choice for production use? It would be nice if you could share your practical experiences

  Read the article

• simple web parts in asp.net show as blank page

  - by Javaman59

  I am trying to develop web parts in VS 2008/WinXP I created a Web Site project, and added a couple of web parts within the default form in default.aspx <form id="form1" runat="server"> <div> <asp:WebPartManager ID="WebPartManager1" runat="server"> </asp:WebPartManager> <asp:WebPartZone ID="WebPartZone1" runat="server"> </asp:WebPartZone> </div> </form> When I first ran it (in the debugger), a popup told to me enable Windows authentication in IIS (so something is working!). I enabled the Windows authentication, and now when I run it I get a blank screen. Same result if I open it in IE via the url (rather than debugger). Following is the the source view. <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head><title> </title><style type="text/css"> .WebPartZone1_0 { border-color:Black;border-width:1px;border-style:Solid; } </style></head> <body> <form name="form1" method="post" action="Default.aspx" id="form1"> <div> <input type="hidden" name="__WPPS" id="__WPPS" value="s" /> <input type="hidden" name="__EVENTTARGET" id="__EVENTTARGET" value="" /> <input type="hidden" name="__EVENTARGUMENT" id="__EVENTARGUMENT" value="" /> <input type="hidden" name="__VIEWSTATE" id="__VIEWSTATE" value="/wEPDwULLTEzNTQyOTkwNDZkZEAVY0VcQaHLv3uaF3svWgCOfsmb" /> </div> <script type="text/javascript"> //<![CDATA[ var theForm = document.forms['form1']; if (!theForm) { theForm = document.form1; } function __doPostBack(eventTarget, eventArgument) { if (!theForm.onsubmit || (theForm.onsubmit() != false)) { theForm.__EVENTTARGET.value = eventTarget; theForm.__EVENTARGUMENT.value = eventArgument; theForm.submit(); } } //]]> </script> <script src="/WebPartsSite/WebResource.axd?d=4lwrtwXryJ3Ri-GXAxZR4g2&amp;t=634003643420884071" type="text/javascript"></script> <div> <table cellspacing="0" cellpadding="0" border="0" id="WebPartZone1"> <tr> <td style="height:100%;"><table cellspacing="0" cellpadding="2" border="0" style="width:100%;height:100%;"> <tr> <td style="height:100%;"></td> </tr> </table></td> </tr> </table> </div> <script type="text/javascript"> //<![CDATA[ var __wpmExportWarning='This Web Part Page has been personalized. As a result, one or more Web Part properties may contain confidential information. Make sure the properties contain information that is safe for others to read. After exporting this Web Part, view properties in the Web Part description file (.WebPart) by using a text editor such as Microsoft Notepad.';var __wpmCloseProviderWarning='You are about to close this Web Part. It is currently providing data to other Web Parts, and these connections will be deleted if this Web Part is closed. To close this Web Part, click OK. To keep this Web Part, click Cancel.';var __wpmDeleteWarning='You are about to permanently delete this Web Part. Are you sure you want to do this? To delete this Web Part, click OK. To keep this Web Part, click Cancel.';//]]> </script> <script type="text/javascript"> __wpm = new WebPartManager(); __wpm.overlayContainerElement = null; __wpm.personalizationScopeShared = true; var zoneElement; var zoneObject; zoneElement = document.getElementById('WebPartZone1'); if (zoneElement != null) { zoneObject = __wpm.AddZone(zoneElement, 'WebPartZone1', true, false, 'black'); } </script> </form> </body> </html>

  Read the article

• Exim mail server slow on sending through SMTP

  - by catalint

  It takes about 30 seconds for the server to send me the banner, but initial connection is done instantly only happens when I am at the office, from home it works fine at the office I have a rRns set-up for my client ip that it's not working. Server: Exim, public fixed ip, rDNS, no ports blocked, in a datacenter Config: hostlist loopback = <; 127.0.0.0/8 ; 0.0.0.0 ; ::1 ; 0000:0000:0000:0000:0000:ffff:7f00:0000/8 hostlist senderverifybypass_hosts = net-iplsearch;/etc/senderverifybypasshosts hostlist skipsmtpcheck_hosts = net-iplsearch;/etc/skipsmtpcheckhosts hostlist spammeripblocks = net-iplsearch;/etc/spammeripblocks hostlist backupmx_hosts = lsearch;/etc/backupmxhosts hostlist trustedmailhosts = lsearch;/etc/trustedmailhosts domainlist user_domains = ${if exists{/etc/userdomains} {lsearch;/etc/userdomains} fail} This happens super fast on the server: 30132 ident connection to 89.238.207.49 failed: Connection refused 30132 sender_fullhost = [89.238.207.49] 30132 sender_rcvhost = [89.238.207.49] 30132 Process 30132 is handling incoming connection from [89.238.207.49] 30132 host in host_lookup? no (option unset) 30132 set_process_info: 30132 handling incoming connection from [89.238.207.49] 30132 host in host_reject_connection? no (option unset) 30132 host in sender_unqualified_hosts? no (option unset) 30132 host in recipient_unqualified_hosts? no (option unset) 30132 host in helo_verify_hosts? no (option unset) 30132 host in helo_try_verify_hosts? no (option unset) 30132 host in helo_accept_junk_hosts? yes (matched "*") 30132 using ACL "acl_connect" 30132 processing "accept" 30132 check hosts = +trustedmailhosts 30132 sender host name required, to match against lsearch;/etc/trustedmailhosts 30132 looking up host name for 89.238.207.49 30132 IP address lookup yielded relay.easycomm.ro Client side 2011.09.14 13:08:13 SMTP (mail.server.ro): Begin execution 2011.09.14 13:08:13 SMTP (mail.server.ro): Port: 465, Secure: SSL, SPA: no 2011.09.14 13:08:13 SMTP (mail.server.ro): Finding host 2011.09.14 13:08:13 SMTP (mail.server.ro): Connecting to host 2011.09.14 13:08:13 SMTP (mail.server.ro): Securing connection 2011.09.14 13:08:13 SMTP (mail.server.ro): Connected to host ---> This is a 1 minute 5 seconds gap 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-genius.filipnet.ro ESMTP Exim 4.69 #1 Wed, 14 Sep 2011 13:09:26 +0300 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-We do not authorize the use of this system to transport unsolicited, 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220 and/or bulk e-mail. 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] EHLO CatalinDell 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-genius.filipnet.ro Hello CatalinDell [89.238.207.49] 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-SIZE 52428800 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-PIPELINING 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-AUTH PLAIN LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 HELP 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorizing to server 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] AUTH LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 VXNlcm5hbWU6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] dGVzdEBzcG9ydGd1cnUucm8= 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 UGFzc3dvcmQ6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] ***** 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 235 Authentication succeeded 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorized to host 2011.09.14 13:09:18 SMTP (mail.server.ro): Connected to host 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] MAIL FROM: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 OK 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] RCPT TO: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 Accepted 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] DATA 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 354 Enter message, ending with "." on a line by itself 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] . ---> This is a 1 minute 10 seconds gap 2011.09.14 13:10:28 SMTP (mail.server.ro): <rx> 250 OK id=1R3mPG-0004T4-7Q 2011.09.14 13:10:28 SMTP (mail.server.ro): End execution --- Initial info I've setup an email account on "Windows Live Mail" that comes with Windows 7 Receiving is super fast, but for some reason sending is very slow, I had to increase the outgoing timeout to 3 minutes in order to make it work. Server software is Exim / Dovecot / cPanel. Do you have any ideeas why there is a slow sending process? Thank you!

  Read the article

• Netbook performance - 1.33 GHz vs 1.6/1.66 GHz Atom

  - by Imran

  All new 11" netbooks seem to carry 1.33 GHz Atom Z520 CPU instead of 1.6/1.66 GHz Atom N270/N280. The screen resolution of 11" netbooks make them very appealing, but I'm a bit concerned about their performance as they carry a slower CPU than the 1.6GHz Atom, which isn't a great performer in the first place. Is there any significant difference in performance between 1.33 GHz and 1.6/1.66 GHz Atom processors in day to day usage? Are any of those fast enough to decode 720p x264 video? (When paired with typical Intel GMA platform and software decoder like ffdshow/CoreAVC of course, not with Nvidia Ion platform)

  Read the article

• WCF, net.tcp, and ASP.NET development server

  - by bryanjonker

  I'm setting up a net.tcp WCF service using instructions here: http://blogs.msdn.com/swiss_dpe_team/archive/2008/02/08/iis-7-support-for-non-http-protocols.aspx One of the steps says to do the following: "If you open the IIS7 management console and you look at the advance setting of our IIS7HostedService Web Application, you will see that in the Enabled Protocols section just http is defined. You now have to add net.tcp (separated by a comma), so that our service will be able to respond also to TCP requests." This is fine, but what if I want to use the Cassini / VS2010 ASP.NET development server to debug (hitting F5 or cntrl-F5)? I don't think there's a way to change the settings in that IIS. Or is there? Are other programmers just so awesome that they don't need to go through the debugger? Or do they use wsHttpBinding?

  Read the article

• How can I implement an abstract singleton class in Java?

  - by Simon

  Here is my sample abstract singleton class: public abstract class A { protected static A instance; public static A getInstance() { return instance; } //...rest of my abstract methods... } And here is the concrete implementation: public class B extends A { private B() { } static { instance = new B(); } //...implementations of my abstract methods... } Unfortunately I can't get the static code in class B to execute, so the instance variable never gets set. I have tried this: Class c = B.class; A.getInstance() - returns null; and this ClassLoader.getSystemClassLoader().loadClass("B"); A.getInstance() - return null; Running both these in the eclipse debugger the static code never gets executed. The only way I could find to get the static code executed is to change the accessibility on B's constructor to public, and to call it. I'm using sun-java6-jre on Ubuntu 32bit to run these tests.

  Read the article

• Suggestions for a nice&small - high battery life programmer notebook

  - by Emir

  Hi guys, I'm planning to buy a new notebook since the Toshiba I have now sucks in battery life. I'm a web designer & programmer, and the main features of the notebook should be: High battery life Small, 13.3" or 14" screen A fast processor and RAM that won't let me down while multi-tasking Anything other than these is secondary, I wouldn't like it to be very pricey though :) I'm now leaning towards Macbook Pro 13.3", 2.66 Ghz; it has 10 hours of battery life. However, I mostly develop on Windows, so I don't know how many hours of battery will I get if I run Windows 7 on Bootcamp. Your ideas and suggestions will be much appreciated.

  Read the article

• in HFT trading should I upgrade from Windows Server 2008 R2 to Windows Server 2012?

  - by javapowered

  I'm using HP DL360p Gen8 + Windows Server 2008 R2 for HFT trading. That means that every 10 microseconds is important for me. I do understand that if I need everything to be so fast I probably should consider using Linux. But in this post I want to compare only Windows Server 2008 R2 and Windows Server 2012. I've found in internet couple articles that suggest how to tune Windows Server 2012 for low latency http://msdn.microsoft.com/library/windows/hardware/jj248719 http://technet.microsoft.com/en-us/library/hh831415.aspx Most part of optimizations from these articles apply only to Windows Server 2012 and can not be used on Windows Server 2008 R2. So now I think that as I can optimize Windows Server 2012 for low latency, probaly I should upgrade? After optimizations how much faster windows server 2012 would be (ideally in microseconds :)?

  Read the article

• Tomcat custom classloader in Liferay principles

  - by lisak

  When custom class loader in webapp context file is used and the context is being initialized and started, the custom classloader is just a substitution for the default webapp class loader, right ? But what are the consequences of doing this? Because, for instance, in Liferay portal an application can use custom PortalClassLoader, which just extends webapp class loader and does nothing else, it's the same class, no modifications at all. And I didn't find any following initializations like repository location changes etc. The point is, that the PortalClassLoader provides the webapp with an access to the ROOT portal context, which AFAIK doesn't use PortalClassLoader, according to debugger.

  Read the article

• Where to call RouteDebugger.RewriteRoutesForTesting() when route registration is injected?

  - by boris callens

  As Phil Haack explains on his blog entry, the Route Debugger helps visualizing your routing tables. My site however gets it's routing injected by the MVCTurbine dependency injection (using Unity) like so: public class DefaultRoutRegistration : IRouteRegistrator { public void Register(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.MapRoute( "Accounts", "Accounts/{userName}/{action}", new { controller = "Account", action = "Index" } ); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "Index", id = "" } // Parameter defaults ); RouteDebug.RouteDebugger.RewriteRoutesForTesting(RouteTable.Routes); } } Where exactly can I throw in the the RouteDebug.RouteDebugger.RewriteRoutesForTesting(RouteTable.Routes); to rewrite my routing table?

  Read the article

• PHP Configuration file won’t load IIS7 x64

  - by Martin Murphy

  using Fast CGI I can't get it to read the php.ini file. See my phpinfo below. System Windows NT WIN-PAFTBLXQWYW 6.0 build 6001 Build Date Mar 5 2009 19:43:24 Configure Command cscript /nologo configure.js "--enable-snapshot-build" "--enable-debug-pack" "--with-snapshot-template=d:\php-sdk\snap_5_2\vc6\x86\template" "--with-php-build=d:\php-sdk\snap_5_2\vc6\x86\php_build" "--disable-zts" "--disable-isapi" "--disable-nsapi" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--enable-htscanner=shared" Server API CGI/FastCGI Virtual Directory Support disabled Configuration File (php.ini) Path C:\Windows Loaded Configuration File (none) Scan this dir for additional .ini files (none) My php.ini file is residing in both my c:\php and my c:\windows I've made sure it has read permissions in both places from network service. I've added various registry settings, Environment Variables and followed multiple tutorials found on the web and no dice as of yet. Rebooted after each. My original install was using MS "Web Platform Installer" however I have since rebooted. Any ideas on where to go from here would be most welcome.

  Read the article

• SqlDateTime overflow on INSERT when date is correct using a Linq to SQL DataContext

  - by Jan Hoefnagels

  Dear Linq experts, I get an SqlDateTime overflow error (Must be between 1/1/1753 12:00:00 AM and 12/31/9999 11:59:59 PM.) when doing an INSERT using an Linq DataContext connected to SQL Server database when I do the SubmitChanges(). When I use the debugger the date value is correct. Even if I temporary update the code to set the date value to DateTime.Now it will not do the insert. Did anybody found a work-around for this behaviour? Maybe there is a way to check what SQL the datacontext submits to the database.

  Read the article

• rename file names from lower case to upper case

  - by Adnan

  Hello, I have about 2k of file that are currently in lower case like: file_one.cfr file_two.cfr .... I am searching for a fast way to rename them to upper case so they would be like; FILE_ONE.cfr FILE_TWO.cfr .... If I use from my shell; for i in *; do mv $i `echo $i | tr [:lower:] [:upper:]`; done I can get all file and the file extensions to upper case. But the extension should remain in lowercase, so my approach does not work. Any programming language is welcome.

  Read the article

• vs2010 asp.net : Procedure or function expects parameter which was not supplied.

  - by dotnet-practitioner

  I have googled for this issue but listed solutions are not working for me... I get the following error message: Procedure or function 'ContactHide' expects parameter '@ContactID', which was not supplied. Here is my setup..What am I missing? Please help? Debugger shows that I am supplying ContactID correctly in my C# code behind code. <asp:SqlDataSource ID="SqlDataSource2" runat="server" ConnectionString="<%$ ConnectionStrings:MYDBConnectionString1 %>" UpdateCommand="ContactHide" UpdateCommandType="StoredProcedure" > int contactid= Convert.ToInt32(e.CommandArgument); SqlDataSource2.UpdateParameters.Add("@ContactID", System.Data.DbType.Int32, "1"); SqlDataSource2.UpdateParameters["@ContactID"].DefaultValue = contactid.ToString(); SqlDataSource2.Update(); ALTER PROCEDURE dbo.ContactHide @ContactID int /* ( @parameter1 int = 5, @parameter2 datatype OUTPUT ) */ AS Update Contacts set Visible = 0 where ContactID = isnull(@ContactID,-1) /* SET NOCOUNT ON */ RETURN

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >