Search Results

Search found 23567 results on 943 pages for 'max link'.

Page 133/943 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Email Mail Merge via linked Excel sheet

  - by Joe Perrin

  I have a MS Word 2007 document setup as a Mail Merge doc. I am using Excel as the data source. The MERGEFIELD ClientData contains an Excel file (test.xlsx). I want to merge the data from the Excel file listed in ClientData into the respective Mail Merge document. However, whenever I start the Mail Merge the {MERGEFIELD ClientData} field gets resolved only once and does not select the next row from ClientData. So this: {LINK Excel.Sheet.12 "C:\\path\\to\\file\\{MERGEFIELD ClientData}" \a \f 4 \h} Becomes this after starting the merge: {LINK Excel.Sheet.12 "C:\\path\\to\\file\\test.xlsx" \a \f 4 \h} So every Mail Merge doc uses the test.xlsx instead of the respective Excel document specific to the client (i.e test1.xlsx, test2.xlsx, test3.xlsx, etc.) As the merge runs through each Mail Merge doc I expect to see this: {LINK Excel.Sheet.12 "C:\\path\\to\\file\\test.xlsx" \a \f 4 \h} {LINK Excel.Sheet.12 "C:\\path\\to\\file\\test1.xlsx" \a \f 4 \h} {LINK Excel.Sheet.12 "C:\\path\\to\\file\\test2.xlsx" \a \f 4 \h} {LINK Excel.Sheet.12 "C:\\path\\to\\file\\test3.xlsx" \a \f 4 \h} But for some reason this isn't happening. Does anyone have any suggestions? Thanks!

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Rails: savage_beast forum plugin and tinymce - new post works but edit doesn't use tinymce properly

  - by Max Williams

  Hi all. I'm using the savage_beast forum plugin and tinymce (via the tinymce_hammer plugin) in my rails app. When posting a new post, tinymce works fine. However, when i go to edit a post i get the tinymce editor, but the content in the edit box has all been converted into html. Can anyone tell me how i get it so that what appears in the tinymce edit box is the original text i posted, rather than the converted-to-html version? Does it need to get converted back from html into a format tinymce will use? Savage_beast saves the original given text in a body field, and the converted-to-html text in a body_html field. After tinymce does its work in the first instance (ie when posting a new post) the body field gets text that's already been converted to html. So i guess i need to convert it back to whatever tinymce expects? I'd expect tinymce to be happy with getting html, and to just handle it, though. grateful for any advice - max

  Read the article

• Nhibernate many to many criteria query with subselect

  - by Max

  I have a simple example of a blog: a Post table, a Tag table and a Post_Tag_MM lookup table linking the two tables. I use this hql query in order to fetch all posts, that DONT have some tags: var result = session .CreateQuery(@" select p from Post p join p.Tags t where (select count(ti) from p.Tags ti where ti.Uid in (:uidList)) = 0 ") .SetParameterList("uidList", uidList) .SetResultTransformer(new DistinctRootEntityResultTransformer()) .List<Post>(); How can this many-to-many query and the subselect translated into a criteria query? I dont quite understand the DetachedCriteria API yet and could not get it to return the right resultset. Thank you very much in advance. Regards, Max

  Read the article

• SQL: Gather right hand values from a join

  - by Max Williams

  Let's say a question has many tags, via a join table called taggings. I do a join thus: SELECT DISTINCT `questions`.id FROM `questions` LEFT OUTER JOIN `taggings` ON `taggings`.taggable_id = `questions`.id LEFT OUTER JOIN `tags` ON `tags`.id = `taggings`.tag_id I want to order the results according to a particular tag name, eg 'piano', so that piano is at the top, then by all the other tags in alphabetical order. Currently i'm using this order clause: ORDER BY (tags.name = 'piano') desc, tags.name Which is going completely wrong - the first results i get back aren't even tagged with 'piano' at all. I think my problem is that i need to group the tag names somehow and do my ordering test against that: i think that doing it against the straight tags.name isn't working due to the structure of the resultant join table (it does work if i just do a simple select on the tags table) but i can't get my head around how to fix it. grateful for any advice, max

  Read the article

• Bind multiple request parameters to one object in Spring 3

  - by Max

  Hi, I can't figure out a way to bind several arguments and headers to one request parameter using annotations in Spring 3. For example, let's say I'm getting this request: Headers: Content-type: text/plain; POST Body: Name: Max Now I want it all to mysteriously bind to this object: class NameInfo { String name; } Using some code like this: String getName() { if ("text/plain".equals(headers.get("content-type"))) { return body.get("name"); } else if ("xml".equals(headers.get("content-type")) { return parseXml(body).get("name"); } else ... } So that in the end I would be able to use: @RequestMapping(method = RequestMethod.POST) void processName(@RequestAttribute NameInfo name) { ... } Is there a way to achieve something similar to what I need? Thanks in advance.

  Read the article

• Tutorials/Books on using Mono to develop RESTful webservices?

  - by max

  Hi, anyone out there got any pointers to good links/tutorials/books on developing webservices with Mono? In more detail, I am interested in using Mono from project start on a Linux host developing in C# using Visual Studio for development, ideally with remote debugging if that is realistic developing web-services in MONO accessible in a RESTful manner, returning JSON hiding the services processes behind an Apache access the services either via javascript/AJAX or from a thin script layer written in PHP scalability is important for me unit-testing of webservices Any recommendations for material I could sift through to get a good head-start? I might add that I'm C#/.NET savvy, but not in the context of web development. I've been using it since it came out, but mainly for internal server-client applications where the clients were Windows desktop apps and the communication layer was remoting or, sometimes, more low-level socket-based. Thanks, max

  Read the article

• Test if current page is inside a shadowbox? (so i can close the shadowbox and reopen that page in t

  - by Max Williams

  Hi all I have a couple of pages in my site which open in a shadowbox window rather than the main window. My problem is that if the user session expires, then the user clicks on one of the links that open in a shadowbox, they are redirected to the login page INSIDE THE SHADOWBOX, which i don't want. I've been trying to think of the best way to handle this - one way i thought of, which seems a bit clumsy tbh, was on the login page to test if we're in a shadowbox, and if we are then close it and redirect the parent window to the login page. a) does this seem like a sensible plan? I added the following to my login page, which works: $(document).ready(function(){ if(window.parent.location != window.location){ window.parent.location.href = window.location; } } but i have to wait for the shadowbox to finish loading the page and then redirect. So it's working but like i say a bit clumsy. Is there a nicer way? grateful for any advice - max

  Read the article

• Android Database

  - by Max

  I'm trying to build a simple app to get to grips with android as I'm new. I have programmed for years in PHP and MySQL so it's not completely unfamiliar to me, but one concept is at the moment confusing to me. If I wanted to create this app with 100's of questions how would I create the database like this. What I mean is at the moment my app runs and creates the database. Would I need to do this everytime the app runs as i'm guessing if it was a lot bigger it would mean a slow load evert time. Or is there a way to create the database once and then when the app runs there is no need to populate it. Max

  Read the article

• Bash PS1 settings - how to get the current folder back as the terminal title

  - by Max Williams

  Hi all. I recently added these lines to my ~/.bashrc file to show the current branch if i'm in a git working folder, and it works nicely for that. However, what i've lost is that the current folder name used to be shown in the tab for the terminal i have open, and now it isn't: it always just says 'Terminal'. Can i get that back and still keep the git stuff? Here's the lines in question - it's the second one that's the issue, as commenting out just the second line fixes the problem. source /etc/bash_completion.d/git PS1='\h:\w$(__git_ps1 "\[\e[32m\][%s]\[\e[0m\]")$ ' I've been looking at explanations of the options for PS1 but can't see anything about the terminal window's title in there. Can anyone advise? thanks, max

  Read the article

• UNIX FIFO: How to allow only one writer/reader pair to use a FIFO?

  - by Max Krug

  Hi! I've written two programs: the first, the "writer", creates a FIFO and writes data into it. The second one, the "reader" runs in background and looks for data in the FIFO. Once data is there, the reader reads it out. If I start e.g. two writers and two readers, they all can write/read into/from the same FIFO. How can I restrict it for 3rd and 4th readers/writers to use the FIFO and allow only one writer and one reader to use the FIFO? thanks a lot. -- kind regards, Max Krug

  Read the article

• make mongrel_rails (localhost:3000) visible to a virtual machine

  - by Max Williams

  I develop rails in ubuntu and i just set up a virtualbox windows xp virtual machine for IE testing. I'd like to be able to run mongrel_rails in ubuntu and then jump into the vm to check it out, so i can jump back, make a change, jump into the vm again, reload the page and test it, etc. Is this possible? In this sort of situation in the past i've had to set up an apache server on my dev machine and run mongrel under that, in order to get an externally visible (ie visible to my local network) ip address that i then paste into the address bar of IE in the vm. Is this really necessary? Is there a simpler way? Can i do something with my /etc/hosts or sites-available files to just make up some arbitrary network address which points to localhost:3000 in ubuntu? Or something? thanks, max

  Read the article

• No exit option if something is running

  - by max

  How can I catch something going on if the user chooses the exit option from a menu? I mean I'd like to be able to manage the event of a user who is going to close the application but some activity is being performed so he/she shouldn't be able to exit. Here's the code I wrote. In a nutshell : recording is being performed -- user clicks exit -- WARNING "Process is running you can't do it"(The process goes on) nothing is running -- user clicks exit -- application closes Is it possible to solve the problem by just adding a few lines of code without having to rewrite the entire program? thanks very much in advance. MAX exitAction = new AbstractAction("Exit") { public void actionPerformed(ActionEvent e) { System.exit(0); } }; exitAction.putValue(Action.NAME, "Exit"); // description exitAction.putValue(Action.SHORT_DESCRIPTION, "Exit application");

  Read the article

• isAlive problem..Help to understand how it works

  - by max

  I get this error: "non-static method isAlive() cannot be referenced from a static context" what's wrong with this code..please. I'd like to detect if the thread is alive... Any help in terms of code will be highly appreciated..thanks max class RecThread extends Thread { public void run() { recFile = new File("recorded_track.wav"); // Output file type AudioFileFormat.Type fileType = null; fileType = AudioFileFormat.Type.WAVE; // if rcOn =1 thread is alive int rcOn; try { // starts recording targetDataLine.open(audioFormat); targetDataLine.start(); AudioSystem.write(new AudioInputStream(targetDataLine), fileType, recFile); if (RecThread.isAlive() == true) { rcOn =1; } else { rcOn =0; } } catch (Exception e) { showException(e); } // update actions recAction.setEnabled(true); stopRecAction.setEnabled(false); } }

  Read the article

• Git is deleting an ignored file when i switch branches

  - by Max Williams

  I have one branch (let's call it B) that ignores a certain file, which isn't ignored in some other branches (eg branch A). When i switch from branch B to branch A, then back to B again, the file has been deleted. Is this normal? I can sort of see how it would happen, in the sense that branch B thinks it's not there, and branch A thinks that it is, so when i go back to B it 'tidies it away'. But it's kind of annoying. Any suggestions? thanks, max

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Bladecenter-E Power Module fault

  - by Lihnjo

  We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

  Read the article

• LVS Configuration issue (Using piranha Tool)

  - by PravinG

  I have configured LVS on cent os using piranha tool .I am using vip of internal n/w as gateway for real server we have two NIC one having exteranl Ip and other for internal n/w which is on 192.168.3.0/24 network. But I am not able to connect from client it shows connection refused error . Please suggest iptables rules for private n public n/w to communicate. May be I am missing this . Iptables rules that we have added are : iptables -t nat -A POSTROUTING -p tcp -s 192.168.3.0/24 --sport 5000 -j MASQUERADE this is my ipconfig: eth0 Link encap:Ethernet HWaddr 00:00:E8:F6:74:DA inet addr:122.166.233.133 Bcast:122.166.233.255 Mask:255.255.255.0 inet6 addr: fe80::200:e8ff:fef6:74da/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94433 errors:0 dropped:0 overruns:0 frame:0 TX packets:130966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9469972 (9.0 MiB) TX bytes:19929308 (19.0 MiB) Interrupt:16 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:00:E8:F6:74:DA inet addr:122.166.233.136 Bcast:122.166.233.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:E0:20:14:F9:2D inet addr:192.168.3.1 Bcast:192.168.3.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:20ff:fe14:f92d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:123718 errors:0 dropped:0 overruns:0 frame:0 TX packets:148856 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18738556 (17.8 MiB) TX bytes:11697153 (11.1 MiB) Interrupt:17 Memory:60000400-600004ff eth1:1 Link encap:Ethernet HWaddr 00:E0:20:14:F9:2D inet addr:192.168.3.10 Bcast:192.168.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:17 Memory:60000400-600004ff eth2 Link encap:Ethernet HWaddr 00:16:76:6E:D1:D2 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:21 Base address:0xa500 and ipvsadm -ln command [root@abts-kk-static-133 ~]# ipvsadm -ln IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 122.166.233.136:5000 wlc TCP 122.166.233.136:5004 wlc lvs server routing table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 122.166.233.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1004 0 0 eth1 0.0.0.0 122.166.233.1 0.0.0.0 UG 0 0 0 eth0 real 1 real 2 we have configured various ports from 5000:5008 . Do we need to this iptables for all ports? Suggest me how should I solve this issue.

  Read the article

• Ubuntu box static routing problem

  - by Rafael

  Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

  Read the article

• Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

  - by Max Kosyakov

  Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

  Read the article

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Ubuntu with KVM guest VM and broken bridges

  - by MadPsy

  I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM is tap5 and is in bridge br0 br0 8000.46720f5c572e no eth0.500 tap5 Second NIC of the VM is tap2 and is in bridge br100 br100 8000.76ad2fc96661 no eth0.100 eth0.101 eth0.103 eth0.104 eth0.105 tap2 On the host, br0 has an IP and br100 does not 21: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 46:72:0f:5c:57:2e brd ff:ff:ff:ff:ff:ff inet 192.168.100.4/24 brd 192.168.10.255 scope global br0 inet6 fe80::d6ae:52ff:febe:777/64 scope link valid_lft forever preferred_lft forever On the guest, its eth0 and eth1 interfaces both have IP addresses 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:da brd ff:ff:ff:ff:ff:ff inet 192.168.100.6/24 brd 192.168.100.255 scope global eth0 inet6 fe80::23e:61ff:fefb:7ada/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:ea brd ff:ff:ff:ff:ff:ff inet 172.16.50.129/25 brd 172.16.50.255 scope global eth1 inet6 fe80::23e:61ff:fefb:7aea/64 scope link valid_lft forever preferred_lft forever On the guest VM, a tcpdump of its eth1 interface (tap2) shows traffic from its eth0 interface (tap5), as if the 2 bridges are themselves bridged. This means any interface on br100 is now bridged across to br0 - which is completely broken. root@chillispot:~# tcpdump -c 1 -n -v -i eth1 net 192.168.100.0/24 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 16:31:24.175583 IP (tos 0x0, ttl 64, id 48054, offset 0, flags [DF], proto TCP (6), length 148) 192.168.100.6.22 > 192.168.100.4.59505: Flags [P.], cksum 0x6c2b (correct), seq 1056321648:1056321744, ack 398642983, win 1700, options [nop,nop,TS val 197473436 ecr 200655363], length 96 What could be bridging the 2 bridges, except the guest VM (which is a stock Ubuntu install)? I am at a complete loss! Thanks.

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• Can't get DHCPd to assign IPs to unknown clients

  - by Jakobud

  I'm using Webmin to admin our DHCPd server. But I'm having a hard time getting it to assign IP addresses to unknown clients. The only way I can get it to assign an IP is to make sure a host is added to DHCPd as a host so that it gets a static-lease IP assigned to it. I thought "Allow Unknown Clients" was the key, but it still isn't assigning IPs to unknown clients. I have a pool setup so that the unknown clients should get an IP between 10.20.0.200 - 10.20.0.249. Here is the config file. What am I missing here? allow unknown-clients; # Primary DHCP server config authoritative; ddns-update-style none; failover peer "dhcp-failover" { primary; address 10.20.0.30; port 647; peer address 10.20.0.25; peer port 647; max-response-delay 60; max-unacked-updates 10; load balance max seconds 3; mclt 3600; split 128; } subnet 10.20.0.0 netmask 255.255.255.0 { allow unknown-clients; option subnet-mask 255.255.255.0; option broadcast-address 10.20.0.255; option routers 10.20.0.100; option domain-name "ourdomain.com"; option domain-name-servers 192.168.10.20; default-lease-time 86400; max-lease-time 86400; option ntp-servers 192.168.10.20; option time-offset -25200; pool { allow unknown-clients; failover peer "dhcp-failover"; max-lease-time 86400; range 10.20.0.200 10.20.0.249; deny dynamic bootp clients; } host Server-myserver { option host-name "whatever.ourdomain.com"; hardware ethernet 00:89:D4:35:4F:13; fixed-address 10.20.0.23; } }

  Read the article

• NIC is receiving, but not transmitting at all?

  - by Shtééf

  I'm trying to fix a very strange problem remotely on a machine at a customer site. The machine is a Dell PowerEdge, I believe a 1950 (haven't verified, but the lspci output matches specs I found.) The machine has two similar NICs, identified as Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) by lspci, and using the bnx2 driver. (I suspect these are on-board and on the same controller, which is what I'm accustomed to for this type of machine.) The primary interface eth0 works perfectly, and is in fact how I am ssh'd in. However, the secondary interface eth1 is not transmitting. I can see this in ifconfig output, for example, where the TX field is always 0. However, it is receiving, and tcpdump shows ARP requests coming from the ISP's gateway on the other side. The interface is physically connected to a Siemens BSTU4 modem, configured by the ISP. The link is properly set to 10MBps and full duplex, without negotation, as the ISP requested. A small /30 subnet is configured. For the sake of anonimity, let's say the machine is 3.3.3.2/30, and the ISP's gateway .1. The machine has no firewall settings whatsoever. Even running something like arping -I eth1 3.3.3.1, and running tcpdump alongside, shows no traffic whatsoever being transmitted on the interface. (But the other side keeps steadily sending ARP requests, and that is all that can be seen.) What could be causing this? Here's some output, anonymized, which may hopefully help: $ ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: d Wake-on: d Link detected: yes $ ip link show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:c5:xx:xx:xx brd ff:ff:ff:ff:ff:ff $ ip -4 addr show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 inet 3.3.3.2/30 brd 3.3.3.3 scope global eth1 $ ip -4 route show match 3.3.3.0/30 3.3.3.0/30 dev eth1 proto kernel scope link src 3.3.3.2 default via 10.0.0.5 dev eth0

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >