Search Results

Search found 29426 results on 1178 pages for 'user99572 is fine'.

Page 134/1178 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141 | Next Page >

Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

- by MTilsted

I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

Read the article
SATA DVD drive refuses to read movie DVDs

- by poke

Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

Read the article
TCP dies on a Linux laptop

- by Roman Cheplyaka

Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

Read the article
Win 7 Media Center - TV - No audio on HD channels

- by Chuzein Part II

I wonder if you can help. I have recently purchased a PCTV Nanostick DVD-T2 290e I am running Windows 7 Home Premium 64bit and I use Windows media center for almost everything. I run a media center machine in my lounge through my Sony AV Amp onto my HD TV. I bought the Nanostick to watch ‘Freeview HD’ programmes when watching the TV through the Media Center – I also have a Sony Freeview Plus system that the Mrs uses. I installed the Nanostick with relatively no issues and as described by many user reviews Media Center picked up the new USB tuner and scanned all the new channels and I was presented with all the HD channels. The issue I have is that there is no audio sound from the HD channels but perfect video. SD works fine. The software that comes with the Nanostick works fine – both sound and vision are perfect for the HD channels. As mentioned, I run my Media Centre lots. I have an extensive DVD and BD collection stored on a server and DVD and BD all play perfectly through Arcsoft Total Media Theatre 5 – with no issues on either SD or HD. My sound card is built into my motherboard and that sends the audio signal to my gfx card and that in turn passes it through to my Sony AV Amp that decodes the audio to be heard on my 5.1 set up. Does anyone have any ideas. I have searched lots on the net and I cant find anyone else with the same issue. I am aware of codecs etc but I don’t really understand it. It also puzzles me that when I read the user/buyer reviews for this product so many people tell the story of faultless installations on the same kind of set up as me.

Read the article
setting the PATH for Git (not for me)

- by Iain

Hi, I'm running OSX 10.6.5 with Git 1.7.1 I have git installed in a non-standard location (though that really should be the standard on a mac;-) in /Library/Frameworks/Git.framework. My own PATH is set fine, git works fine, until... I set up a pre-commit hook with a Ruby script: $ git commit -m "added some Yard documentation" .git/hooks/pre-commit: line 1: #!/usr/bin/env: No such file or directory The pre-commit.sample runs ok, so it appears that git can't find /usr/bin/env, or much else as I've tried shebanging it directly to ruby etc. Just /bin/sh is ok. So, where does Git get it's PATH? because it's not using mine or this wouldn't be happening. And more to the point, how do I get it to see /usr/bin/env ? I've tested the ruby script already, it works. Just to add: $ cat /etc/paths /usr/bin /bin /usr/sbin /sbin /usr/local/bin $ cat /etc/paths.d/git /Library/Frameworks/Git.framework/Programs The first few lines of the Ruby script (which runs via ./pre-commit or ruby pre-commit) #!/usr/bin/env ruby -wKU class String def expand_path File.expand_path self end def parent_dir File.dirname self.expand_path end end

Read the article
Can't access server sound card when vnc'd into ubuntu server

- by Corey Kennedy

I've set up my ubunutu 10 server with xfce, nxserver, and now tightvncserver so that I can control it remotely from my Windows 7 laptop. NX is working fine for remote access, but when I run (for example) exaile, no sound will be sent through the server's sound card. I installed tightvncserver and connected, but ran into the same problem. Exaile opens, sound isn't muted, I can see that sound cards are installed (via cat /proc/asound/cards), but I can't seem to get the remote sessions to access the server's sound card. Also, just to confirm that the sound card was working I hooked up a montior/keyboard to the server and opened a local xfce session. That worked fine. While I had the local session running, I was also able to open a remote session with NXClient and start exaile - which then successfully piped sound to the local card. After disconnecting the monitor/keyboard and moving the box back to its normal spot, though, I was not able to play sound via either an NX or VNC session. Does anyone have any suggestions? Surely it's possible to configure my remote sessions to pipe sound to the server's sound card, right? Or at least get xfce up and running without a monitor or keyboard but with access to the sound card so I can VNC into it? Thanks!

Read the article
Host couldn't be reached by domain name, only by IP: Apache's fault?

- by MaxArt

I have this Windows Server 2003 R2 32 bit machine running Apache 2.4.2 with OpenSSL 1.0.1c and PHP 5.4.5 via mod_fcgid 2.3.7. This config worked just fine for some hours, but then the site couldn't be reached with its domain name, say www.example.com, but it could be still reached by its IP address. In particular, while https://www.example.com/ yielded a connection error, http://123.1.2.3/ worked just fine. Yes, first https then http. Error and access logs were clean, i.e. they showed no signs of problems. Just the usual messages, that were interrupted while the site couldn't be reached. After some investigation, a simple restart of Apache solved the problem. Unfortunately, I didn't have the chance to test if https://123.1.2.3/ worked as well, or if http://www.example.com/ was still redirected to https as usual. So, has anyone have any idea of what happened? Before I get tired of Apache and ditch it in favor of Nginx? Edit: Some log informations. The last line of sslerror.log is from 90 minutes before the problem occurred, so I guess it's not important. ssl_request.log shows nothing interesting, too: these are the last two lines before the problem: [28/Aug/2012:17:47:54 +0200] x.x.x.x TLSv1.1 ECDHE-RSA-AES256-SHA "GET /login HTTP/1.1" 1183 [28/Aug/2012:17:47:45 +0200] y.y.y.y TLSv1 ECDHE-RSA-AES256-SHA "POST /upf HTTP/1.1" 73 The previous lines are all the same and don't seem interesting, except 4 lines like these 30-40 seconds before the problem: [28/Aug/2012:17:47:14 +0200] z.z.z.z TLSv1 ECDHE-RSA-AES256-SHA "-" - These are the corrisponding lines from sslaccess.log: z.z.z.z - - [28/Aug/2012:17:47:14 +0200] "-" 408 - ... x.x.x.x - - [28/Aug/2012:17:47:54 +0200] "GET /login HTTP/1.1" 200 1183 y.y.y.y - - [28/Aug/2012:17:47:45 +0200] "POST /upf HTTP/1.1" 200 73

Read the article
Change source address based on destination IP

- by hgj

We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

Read the article
Convert MPG w/ AC3 audio to something else - on a Mac

- by anonymous coward

I'm helping with a small volunteer media team, and they have several .mpg videos that don't appear to have sound when played in QuickTime, iTunes, Real Player, etc, on the local Mac machine. I was able to hear audio after transferring one of the movies to a Windows machine that had VLC media player on it. Through VLC I was able to discover that the audio stream is a52 / AC3 format. We use Autodesk Cleaner in our normal workflow of converting the format of our videos to FLV, but for some reason it's unable to convert this particular batch of videos (well, the video converts fine, but with no audio). Obviously, it seems that there's a codec issue here, but I'm not sure how to correct it. (I'm not extremely familiar with Macs, and/or Autodesk Cleaner). I've seen the Perian codec pack, but I'm not sure that having the codecs on the system will enable Cleaner to convert these videos (particularly the audio stream, since the video converts fine). Is there something obvious that I'm overlooking, or will we have to use something else for this particular batch of videos? If so, what?

Read the article
Combining AD permissions with FTP

- by user64204

We're using Windows Server 2008 with Active Directory controlling access to a network share. We've setup FTP so that people can access that share from outside (we used to use the PPTP VPN but for various reasons we need to switch to FTP). So far here is what we've managed to implement on the FTP: -The network share is used as the FTP root (defined as a UNC) and that is working fine. -AD authentication is working fine (wrong password and you stay out, good password you're in, password management in AD correctly synched with the FTP). -AD permissions are failing: the AD permissions on the content of the FTP root are ignored: it's either a user only has read or write access, but this applies to the whole FTP root, which obviously isn't suitable since that FTP root is initially our network share and files/folders have different AD permissions depending on people's groups... Whether we set the permissions through the share OR the FTP management interface, AD permissions are never enforced. Q1: Is that normal? Q2: If so what solutions exist to combine AD permissions with FTP on MS server 2008? Q3: If not, where should I look to fix the configuration?

Read the article
Very Slow DSL (ethernet) speed [New Interesting Update]

- by Abhijit

Very IMPORTANT and INTERESTING UPDATE: Due to some reason I just thought to do a complete new setup and this time I decided to again have openSUSE plus ubuntu. So I first reinstall lubuntu and then I installed OpenSUSE 12.2 (64 bit). Now, my DSL speed is working very normal and fine on opensuse. So this is very scary. Is it possible for any operating system to manipulate my NIC so that it will work fine only on that operating system and not on another os? Regarding positive thinking and not being paranoid, what is it that makes ONLY suse to get my NIC to work at normal speed but ubuntu can not do it? Not even fedora? Not even linux mint? What all these OS are lacking that enables suse to work great? == ORIGINAL QUESTION == I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

Read the article
Running .NET code in XML file [closed]

- by Stuart McIntosh

We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr=""<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>""/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

Read the article
Losing internet connection after few minutes (5-10 maybe)

- by Korchkidu

I took a computer that was not updated for months. Internet was working just fine so basically, I updated zonealarm, avast and installed all windows updates and especially SP3. After that, when I reboot, Internet works fine but after few minutes, Firefox says that the connection was reset. IE does not work either. However, my connection is still up and running as I can make a ping on www.google.com for example. Here are the solutions I tried with no success so far: 1) Uninstalling SP3; 2) Uninstalling IE8 and IE7; 3) Manually setting DNS and IPs; 4) Removed proxy settings from Firefox and IE; 5) Restarting DNS and DHCP related services; 6) Reset TCP/IP with netsh int ip reset c:\resetlog.txt; 7) Updated my ehternet card driver; 8) Restarted, tweaked all the connections in any directions and any configuration possible I believe; 9) Disabled Zone Alarm and Avast; Also, update kb981793 always fails on install. Please, help me as I spent two days already on this and I cannot find any solution. If I cannot fix this problem tomorrow, I will have to format-reinstall everything. Thanks for any help. Regards.

Read the article
grub refuses to install to raid array

- by ronno

I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

Read the article
SSH agent forwarding on debian squeeze

- by nfvindaloo

Im trying to set up SSH forwarding like this osx debianA debianB I can connect to debianA fine, using ssh -A and it has the following env vars when i do: SSH_AGENT_PID=1543 SSH_AUTH_SOCK=/tmp/ssh-giwdYY1542/agent.1542 SSH_CLIENT='92.233.199.x 38954 22' SSH_CONNECTION='92.233.199.x 38954 108.171.179.x 22' SSH_TTY=/dev/pts/0 When i try to connect to debianB, the agent is not used! ssh -v output ends with: debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /home/nic/.ssh/id_rsa debug1: Trying private key: /home/nic/.ssh/id_dsa debug1: Next authentication method: password Then im asked for a password. I have not set any ForwardAgent no directives in ssh_config and dont have a .ssh/config at all. sshd_config has not got AllowAgentForwarding in it. I have tried all of these directives as yes also. debianA and debianB both have identical ssh_config and sshd_config (verified with diff) so the really weird thing is connecting OSX debianB debianA works fine!! Im totally out of ideas! Has anyone come across this before? Cheers! NFV

Read the article
External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

- by tom

Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

Read the article
Are these three brand new sticks of RAM really dead?

- by David Brown

I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

Read the article
Gigabyte H55N-USB3: No video on HDMI

- by newt

I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

Read the article
Port(s) not forwarding?

- by user11189

I have cable internet service through Charter Communications and feed two desktop computers through a Linksys RP614v3 router. One system is my wife's running WinXP Home Edition and the other is mine, running Vista Home Premium (sp1). I have port forwarding configured in the Linksys so I can access the Vista system remotely using TightVNC. Initially, it worked great and I was able to remotely tend email and access local files while out of town for work. Lately, the cable internet service appears to flicker intermittently and upon return, my Mailwasher program loses ability to access the net and I've been unable to make the remote connection. When I reset the port forwarded for email in the router control panel, Mailwasher functionality returns but as I'm home when that happens, I have no easy way to check remote access until the next time I'm on the road or at work. I'm at my wit's end -- the TightVNC client accesses fine from my wife's system from behind the modem/router setup but I don't know how to maintain whatever gets reset when I fiddle with the control panel and the need to do so at all is new. I accessed it fine for a week off and on while out of town a month ago and now I can't leave home and access it from work an hour later.

Read the article
Western Digital HDD now freezes my BIOS when loading the video card!

- by Vercas

After I have successively and successfully installed 3 Windows XP's on the same partition (Don't ask why...), I restarted my computer again and the BIOS just froze when it loaded the video card. Together with my uncle, we tracked down the problem and found out it's the HDD's fault. We tried booting without the HDD and it worked! (No other HDD (I have only one) but with a Ubuntu Live CD in.) We tried the HDD with a different data bus (It was from an identical computer) but that one didn't let my BIOS recognize the HDD. We also put the HDD in another computer as the second HDD and it DID recognize it but Windows XP kept saying it cannot install a driver and that it installed successfully. Happily, I have managed to backup some of my most important files in that other computer. The following is a list of tests that we have run. With the HDD Original data bus Original computer Result: BIOS freezes WITHOUT the HDD Original data bus Original computer Result: Everything works just fine! With the HDD ANOTHER data bus Original computer Result: Cannot see the HDD With the HDD Original data bus ANOTHER computer Result: It worked! With the HDD ANOTHER data bus ANOTHER computer Result: It worked! During the tests, we had only two data buses and two computers. (each data bus from it's own computer) Strange thing is that the second data bus cannot let the BIOS see the HDD in my computer but works just fine with the other computer. I beg you to help me! I have my most important data on that HDD and I really cannot afford to buy another decent IDE HDD now!

Read the article
Java: compile and run hanging at command prompt

- by dwwilson66

I'm having an issue that I'm hoping someone can help with. I'm working on netbook running WinXP Pro SP3, 1.6GHz & 1GB of RAM. I've got a relatively simple java program that I'm able to successfully compile and run on other computers (both XP and Win7), so I suspect my code is working fine--I've verified that all computers are running the same version of Java (build 1.7.0_02-b13). For about the past week, I get maybe three or four compiles and runs at the command prompt (running CMD from within WinXp) before I hang with a blinking cursor after keying my command and pressing enter. If I shut down the command prompt window and restart it, I can compile and run the program just fine--again, pointing to an OS/environment issue rather than code. The only system change I've made in the past week is to uninstall a Lexmark printer that I ditched a year ago, and removing/reinstalling Java. Oh, and an automatic Windows update... :\ I've used this netbook successfully for programming classes for the past year and a half. Anyone familiar with this issue and know of some system tweaks to solve it? I suspect that memory may not be getting cleaned up when the java program quits...only when CMD closes, but don't know any tools to troubleshoot. Ideas?

Read the article
SSH not working through Double NAT

- by d_inevitable

I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

Read the article
DVI output only working on Windows, not during booting or on Linux

- by Mononofu

So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

Read the article
nginx virtual hosts are not working, all vhosts goes to the default one

- by Adirael

Hello, I just did a clean install of nginx + php-fpm on a VPS running Ubuntu 10.10, nginx is serving and PHP is working fine, but I'm not able to add vhosts to it. Well, I can add them, but only one works, the rest go to this first one. This is my first vhost, for host1: server { listen 80; server_name host1; access_log /var/log/nginx/host1.log; error_log /var/log/nginx/host1.error.log; location / { root /var/www/vhosts/host1/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host1/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } And the second one, for host2: server { listen 80; server_name host2; access_log /var/log/nginx/host2.log; error_log /var/log/nginx/host2.error.log; location / { root /var/www/vhosts/host2/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host2/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } The problem is, when I go to http://host1 everything is fine, but on http://host2, it just shows host1! I don't have Apache installed and everything comes from repos. Any pointers?

Read the article
Unable to set initcwnd on a Hetzner server

- by Sergi

We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141 | Next Page >