Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 136/468 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

  • What are potential reasons a user could be connected to a home network, but not to the internet?

    - by Matthew
    I have a friend that recently started using Ubuntu, and I've been answering his questions via the internet. However, I'm stuck on this one. He bought Linksys WPC11 wireless card, and says he was able to create a network connection, but was unable to ping or use a browser. I'm not quite sure where to start in figuring this out--what are some common causes of this sort of problem?

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • Could some one please explain the various proxy configuration scenarios?

    - by RP.
    I am working on a client application in C# which does a various kinds of communication with a server( eg: uploads, downloads etc ). We have a legacy system which does the same functionality and we get in to proxy configuration related issues frequently.It uses the settings from internet explorer network settings. Most of the time these are due to specific proxy configuration( Eg: Proxy auto-config etc ). I am trying to understand the various scenarios used in corporate environments for proxy configurations. Could some one please explain the various proxy configuration scenarios?

    Read the article

  • Trixbox CentOS Default GW Problem (Multi-homed server)

    - by slashp
    I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

    Read the article

  • Remote Desktop fails after VPN connection.

    - by Samet Sorgut
    The remote computer is connected with Remote Desktop. When the remote computer is connected to VPN the Remote Destop freezes. It is not possible to connect to the remote computer again via Remote Desktop. What can be done to connect to this remote computer after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest?

    Read the article

  • Amazon EC2 instance missing Network Interface

    - by Sergiks
    I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

    Read the article

  • My internet drops and will only reconnect if I troubleshoot it or restart my computer.

    - by Paul
    My internet loses its connection and at the same time, and my speaker seems broken if that happens and my mouse will not be smooth as it was before it happens. It already happened before and I didnt mind it. But now, it's happening literally all the time. After startup, my connection seems okay but after some few minutes, even without me doing something, my laptop will just lose its connection. It says that it is not connected and connections are available, but if I check if there are connections where I can connect it shows nothing. Even if, there is actually a wi-fi connection where my phone and other laptops connect. They dont seem to have problem with it. Just my laptop. After that happens, I usually restart my laptop but I discovered that troubleshooting it would somehow repair the problem, but not all the time. It says that restarting my wireless adapter do the job. Are there any long term fix? I mean that could last long or totally erase the problem? I have Atheros AR5B97 Wireless Network Adapter and Microsoft Virtual WiFi Miniport Adapter, both enabled. On the services, I have Wired AutoConfig and WLAN AutoConfig on Automatic. Aspire 4750, Windows 7 (x86)

    Read the article

  • What would cause different rates of packet loss between client and server in UDP?

    - by febreezey
    If I've implemented a reliable UDP file transfer protocol and I have a file that deliberately drops a percentage of packets when I transmit, why would it be more evident that transmission time increases as the packet loss percentage increases going from the client to server as opposed from the server to the client? Is this something that can be explained as a result of the protocol? Here are my numbers from two separate experiments. I kept the max packet size to 500 Bytes and the opposite direction packet loss to 5% with a 1 Megabyte file: Server to Client loss Percentage varied: 1 MB file, 500 b segments, client to server loss 5% 1% : 17253 ms 3% : 3388 ms 5% : 7252 ms 10% : 6229 ms 11% : 12346 ms 13% : 11282 ms 15% : 9252 ms 20% : 11266 ms Client to Server loss percentage varied 1 MB file, 500 b segments, server to client loss 5% 1%: 4227 ms 3%: 4334 ms 5%: 3308 ms 10%: 31350 ms 11%: 36398 ms 13%: 48436 ms 15%: 65475 ms 20%: 120515 ms You can clearly see an exponential increase in the client to server group

    Read the article

  • Not getting gigbit from a gigabit link?

    - by marcusw
    I just upgraded my LAN to gigabit. This is what netperf has to say about things. Before: marcus@lt:~$ netperf -H 192.168.1.1 TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 (192.168.1.1) port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.02 94.13 After: marcus@lt:~$ netperf -H 192.168.1.1 TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 (192.168.1.1) port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 16384 16384 10.01 339.15 Only 340 Mbps? What's up with that? Background info: I'm connecting through a gigabit switch to a sheevaplug. I have Cat5e wiring in the walls and the run is maybe 30 feet. If you're not familiar with netperf, it has a tendency to give very stable results and never lie.

    Read the article

  • Are there any tests I can run on a network to simulate 100 heavy network users?

    - by marc.gayle
    I will be hosting a Ruby on Rails workshop at a small hotel in the near future, and while they have 'Wifi' everywhere on the property, and the property normally hosts 150 - 300 people, I am not 100% confident that they have hosted 150 tech people that tend to have heavy web surfing habits/needs. Their tech department is also 1 or 2 guys. Are there any automated tests I can download and run from my laptop, on the network, that would simulate 100 'heavy users' on the network at the same time? Their broadband pipe is a 15mbps cable connection. Would that suffice for the general surfing needs of 100 - 150 techies? I know all it takes is 1 or 2 bit torrenters to kill the entire network, but assuming we can at the very least block those ports or encourage the attendees not to file share on the network, would that speed suffice for general surfing needs? What are good resources online that would allow me to quickly get up to speed on the IT related issues, so that I can ask their sysadmins the right questions? Edit: Note that I am fairly technical, so assume I can get up to speed quickly even with technical manuals, etc.

    Read the article

  • will heavy network traffic affect other connections on HP ProCurve V1810-48G?

    - by nn4l
    I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

    Read the article

  • MS Vista taking too long to identify Wi-Fi connection [closed]

    - by I_M_SUPER_USER
    I with few of my flat-mates share internet connection by using ASL cable into one laptop and then making Adhoc private network so that we all can enjoy internet connectivity. It all worked wonderful few initial days, but now my MS vista is taking much time to identify that adhoc network and it though I am connected to my friend, it takes 5-10 minutes untill I use internet.

    Read the article

  • Network trials and tribulations

    - by MauiWowie
    Hi, I am in the process of setting up a small (two PC's, both running Windows 7) network using a D-link DI-604 router (which acts only as hub, it's not set up in any way). In the Network and 'Sharing Center' in 'Control Panel' I clicked 'Set up a New (Connection or) Network'. All went well up until the moment I attempted to connect one PC with the other (in the 'Connect' dialog I entered the other PC's IP, no pwd). I can use both PC's to connect to and browse the net though, so the router/hub does not seem to be the problem. And I must have done something right, because the other computer shows up in the 'Network Map'. Any and all help is much appreciated!

    Read the article

  • SQL Server: error when connecting

    - by atricapilla
    (migrated from stackoverflow) The application I'm using tries to connect SQL Server named instance running on a dedicated database server. Here's the error I'm getting: The TCP/IP connection to the host <instance_name>, port 1433 has failed. Error: Connection refused: connect. Is the firewall blocking my access or what? Should I dedicate a different port for this application?

    Read the article

  • routing traffic between two network cards through firewall

    - by RubyFreak
    I'm trying to test a network device (firewall) using a Linux box, with two network cards, one interface connected to the WAN zone and another interface to LAN zone. The configuration is similar with that |ETH0| <-> | FW | <-> ETH1 So from both interfaces I'm able to ping the respective firewall interface. But i'm not able to fire something like: ping -I eth0 ip.from.eth1 and to get any answer. Is that possible or should the linux network namespace solution or user level tcp stacks (VMs are out of question)

    Read the article

  • Windows 7 Wireless Network Adapter Stopped Working

    - by Andrew B Schultz
    I have a Windows 7 Ultimate machine where the wireless adapter all of a sudden started having trouble connecting to wireless networks. Whenever I go to a new place and try to connect to a wireless network, it says that the DNS server is not responding, and tells me to go unplug the router and try again. After several locations in a row telling me this, I began to realize something was wrong with my adapter, not the routers. I am no longer asked to identify the security level for any new networks (Work, Home, or Public) like I used to be (it defaults to Public now - with the park bench icon). Often, resetting the router doesn't even work. Running the Windows 7 troubleshooter doesn't give me anything better than the advice to reset the router. However, the adapter will still connect to the wireless network at my main office without any problems. Does anyone know why a wireless network adapter can get so finicky so suddenly? Thanks!

    Read the article

  • Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

    - by Andrew Bolster
    I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

    Read the article

  • How to add a broadcast address to loopback with ifconfig on a OS/X?

    - by chrisapotek
    I am trying to use ifconfig to turn on broadcast on my loopback interface. It currently reads: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 As you can see, no broadcast address! :( :( :( I tried this on OS/X but it did not work and it did not give any error or feedback: ifconfig lo0 broadcast 127.255.255.255 Any guru would know that? I have one server that sends one packet. I have two clients running on the same machine as the server. I need them to pick up the packet WITHOUT having to force the server to send it twice.

    Read the article

  • wifi routers and concurrent devices

    - by Joelio
    We have a Linksys WRT54G WiFi router in our office which was working great when we had 5-6 folks. Now on peak days we have 10-15 people, each with a computer, smartphone, etc, and an ooma VOIP device. On average 1-2 times a day I need to go hard reboot the router, and sometimes the border router (Cox-supplied device). I assume this is just because the router cant handle this many concurrent users. So my question is can these consumer routers handle this kind of load? If not, would adding more devices solve the problem, and how close proximity can I put 2 routers without having interference problems (our office area is not that big physically)?

    Read the article

  • Unable to ping gateway via bridge nic

    - by Ara
    I'm trying to install KVM on Ubuntu 12.04 server. We have multiple nic on this server of which we primarily use eth0. The server network runs fine(i'm able to ping gateway, ping dns server and ping servers on internet) with eth0 /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local I installed bridge-utils and configured br0 as below /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off Post which i'm able to ping servers on the same ip range 192.168.22.2-254 except for 192.168.22.1 (which is the gateway) also i'm not able to ping any other servers. I'm not able to ping this machine from network. The output for route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.22.1 0.0.0.0 UG 100 0 0 br0 192.168.22.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 I've been struggling with this issue for past 5 days, would be of help if anyone can point me in the right direction to fix this issue. Thanks in advance

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • Why can't I access my own web server from my local network?

    - by frenetic
    I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

    Read the article

  • OpenWRT LAN clients don't see each

    - by Valentin Galea
    I'm a beginner at using OpenWRT but I'm loving it already. Everything is running fine (internet, wifi) on all clients except one thing: the computers running in my LAN don't see each other. Pings to them or between them gives "destination host unreachable". This happens when using either the machine's IP's or their assigned hostnames. Running Backfire 10.03.1 - default settings everywhere except of course for the specific ISP stuff in the WAN. What's going on?

    Read the article

  • How to set up multiple SSIDs with bandwidth limiting on a single wireless router?

    - by Rahul Narain
    I have an Asus WL-520GU wireless router connected to a cable modem that I use for wireless internet access in my apartment. I would like to set it up so that it provides two SSIDs: one secured and password-protected for my regular use, and a "guest" SSID that's unsecured but throttled to, say, 10% of the available bandwidth. What is the most straightforward way to do this? I've been looking into DD-WRT and Tomato, both of which support my router. DD-WRT supports setting up multiple SSIDs using the GUI, but I don't know if it's possible to limit the bandwidth of each SSID independently; point #12 in this FAQ thread says it's not possible to limit by day or by MAC address, which is discouraging but not conclusive. Tomato allows bandwidth limits in its QoS settings, going by the screenshot here, but multiple SSID support is still experimental and it doesn't look like it will work with the encryption settings or bandwidth limits in the GUI. I'd like to know a good way to do this which gives me the fewest opportunities for screwing up. I'm no stranger to the command line, if that turns out to be what's necessary, but if so, please explain what the commands are doing because I don't have a good mental model of what needs to happen to set this up.

    Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >