Search Results

Search found 5137 results on 206 pages for 'i like traffic lights'.

Page 138/206 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• Setting up routing for MS DirectAccess to a VMWare EsXi Host

  - by Paul D'Ambra

  I'm trying to set up DirectAccess on a virtual machine so I can demonstrate it's value and then if need be add a physical machine to host it. I'm hitting a problem because the Direct Access machine (DA01) needs to have 2 public addresses actually configured on the external adapter but there is a Zyxel Zywall USG300 between the VMware ESXi host and the outside world. I've summarised my setup in this diagram If I ping from the LAN to 212.x.y.89 I get a response but if I ping from the VM I get destination host unreachable. I used "route add 212.x.y.89 192.c.d.1" and get request timed out. At that point I see outbound traffic allowed on the Zyxel firewall but nothing coming back. I'm past my understanding of routing and VMWare so am not sure how to tie down where my problem lies (or even if this setup is possible). So any help massively appreciated. Paul

  Read the article

• Setting up dante socks server

  - by skerit

  I want to tunnel all my internet traffic through my vps, so I'm trying to install a proxy server. However: I can't seem to browse the internet through Dante. I get the ERR_EMPTY_RESPONSE error. This is my config: logoutput: stderr /home/user/dantelog internal: eth1 port=1080 external: eth1 method: username pam user.privileged: proxy user.notprivileged: nobody user.libwrap: nobody client pass { from: 10.0.0.0/8 port 1-65535 to: 0.0.0.0/0 } Do I really have to run 2 proxy servers: one for http and one for socks? or is there something else I can do?

  Read the article

• Proxmox 31 + KVM routing + IP subnet + csf

  - by KeyJey

  We have proxmox 3.1 server in netzner with routuing network and IP subnet block. We want to implement csf firewall without interfering the traffic of the KVM VMs, what would be the easiest way? We readed that we should add this lines to /etc/csf/csfpost.sh: iptables -A FORWARD -d 144.76.223.155 -j ACCEPT iptables -A FORWARD -d 144.76.223.156 -j ACCEPT iptables -A FORWARD -d 144.76.223.157 -j ACCEPT iptables -A FORWARD -d 144.76.223.158 -j ACCEPT iptables -A FORWARD -d 144.76.223.159 -j ACCEPT iptables -A FORWARD -d 144.99.183.323 -j ACCEPT But when we enable csf the ping breaks, this is the network config (IPs are modified): auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 144.76.166.100 netmask 255.255.255.255 pointopoint 144.76.183.97 gateway 144.76.183.97 # for single IPs auto vmbr0 iface vmbr0 inet static address 144.76.166.100 netmask 255.255.255.255 bridge_ports none bridge_stp off bridge_fd 0 up ip route add 144.99.183.323/32 dev vmbr0 # for a subnet auto vmbr1 iface vmbr1 inet static address 144.76.166.100 netmask 255.255.255.248 bridge_ports none bridge_stp off bridge_fd 0 Thanks in advanced ! :)

  Read the article

• Using IIS7 as a reverse proxy

  - by Jon

  Hi All, My question is pretty much identical to the question listed but they did not get an answer as they ended up using Linux as the reverse proxy. http://serverfault.com/questions/55309/using-iis7-as-a-reverse-proxy I need to have IIS the main site and linux (Apache) being the proxied site(s). so I have site1.com (IIS7) site2.com (Linux Apache) they have subdomains of sub1.site1.com sub2.site1.com sub3.site2.com I want all traffic to go to site1.com and to say anything that is site2.com should be proxied to linux box on internal network, (believe ARR can do this but not sure how). I can not have it running as Apache doing the proxying as I need IIS exposed directly. any and all advice would be great. Thanks

  Read the article

• Exposing a WebServer behind a firewall without Port Forwarding

  - by pbreault

  We are deploying web applications in java using tomcat on client machines across the country. Once they are installed, we want to allow a remote access to these web applications through a central server, but we do not want our clients to have to open ports on their routers. Is there a way to tunnel the http traffic so that people connected to the central server can access the web applications that are behind a firewall ? The central server has a static ip address and we have full control over it. Right now, it is a windows box but it could be changed to a linux box if necessary. Our clients are running windows xp and up. We don't need to access the filesystem, we only want to access the web application through a browser. We have looked at reverse ssh tunneling but it shows scaling problem since every packet would have to pass through the central server.

  Read the article

• Need IPSec help on Windows 2003

  - by user37456

  Hey guys, I am trying to configure IPSec between a web and app server in our environment. I want all traffic between these two servers to use IPsec and be encrypted. These servers are on the same domain so i am currently using Kerebos for security, I have also tried pre-defined keys and nothing changed. When I try and ping between the servers I get "Negotiating IP Security" everytime. I have also confirmed that when I change "Require Security" to "Permit" everything works so IPSec is working, I believe its something with my security setup. Under the security tab both servers have the default 3DES keys first and then DES keys. I have also specified tunnel endpoints (the alternate server's IP). What am I missing? Thanks for any help..

  Read the article

• Network architecture when using Rackspace's Cloud

  - by brianz

  I'm planning on launching a web application soon, and have decided on using Rackspace's Cloud offering with Debian. I'm not expecting that much traffic to start, but would rather get the architecture correct now even with the small VPSs. The thing I'm not quite sure about is how many VPSs I should get. At a minimum, I know I'll want three VPSs: Two Apache webservers One server for MySQL I'd also like: Nginx load balancer MySQL replication memcached I'm not sure where those last three processes should be running. Can the load balancer run on the same machine as the MySQL slave, or should they each run on their own machine? Does memcached run alongside the webservers or on different machines?

  Read the article

• Apache Reverse Proxy server and SSL NTLM SharePoint

  - by user50211

  Hi, I'm trying to set Apache as proxy server to an internal SharePoint server. I have previously configured Apache to run as a proxy server to export internal webpages and web applications. However, the Sharepoint is using SSL and NTLM authentication, and this is new to me :( I have tried many options, the traffic seems to be forwared as I get the authentication popup window, but when I insert the user/pass, I get back to the same popup window. Anybody has configured Apache to do so? Here is a part of my httpd.conf: <VirtualHost *:443> ServerName repository.out.com SSLProxyEngine On RequestHeader set Front-End-Https "On" ProxyRequests Off ProxyPreserveHost On ProxyPass / https://sharepoint.in.com ProxyPassReverse / https://sharepoint.in.com CacheDisable * SetEnv force-proxy-request-1.0 1 SetEnv proxy-nokeepalive 1 ErrorLog logs/jlanza_log CustomLog logs/jlanza_log common </VirtualHost>

  Read the article

• Teredo and IPV6 web servers

  - by Sandro Antonucci

  Hello, I have two different questions, the first one could be stupid. I was reading about IPV6 and ended up in this site http://test-ipv6.com/ that says that I have a public IPV6 with Teredo tunneling. I don't understand if this Teredo is a software thing, does it have to with my ISP, is it enabled by Windows, how do I get that IPV6 IP, where does it come from? I have windows 7. Second question, I have a VPS with IPV6 connectivity only I can connect to it (apparently thanks to Teredo) and visit pages from the web server using IPV6 IP directly into the browser, is it possibile to host a website on there accessible by the IPV4 network? maybe some dns servers than tunnel traffic from IPV4(user) to IPV6(server)? Thank you

  Read the article

• Most awesomely bad hack

  - by Zypher

  As I sit watching one of my latest dirty dirty hacks run, I started wondering what kind of dirty hacks you have created that are so bad they are awesome. We all have a few of them in our past - and they are probably still running in production somewhere, chugging along somehow still working. Which reminds me of the hack we had to put into place when we were moving data centers. Our IVRs had to keep running, as the data center we were moving from was the primary DC, and the new Primary wasn't quite ready to take traffic. So what do we do. Well we answer the calls in DC1, then ship the sip stream over the internet to DC2 1900 miles away ... that just felt oh so wrong. So the question is, what is one (or more) of your awesomely bad hacks?

  Read the article

• Smoothwall Express interface issues

  - by Timbermar

  I have a SmoothWall Express box that is currently configured with a Green and Purple interface. Both interfaces are in the same /24 subnet (which seems odd to me). The green interface (address of .254) has a DHCP server that is pushing addresses from .1 to .100 and the purple interface (.253) is pushing addresses from .101 to .120. Every machine here is trusted, and as such is connected to the green interface via a wired connection or wireless APs. Nothing is connected at all (port is physically empty, traffic graphs show no activity) to the purple interface. However, every machine here is pulling addresses from the purple interface. So the question boils down to, how do I remove/stop my machines from pulling from the purple dhcp interface? Also, shouldn't the purple interface (if we were using it for guest Wifi or something) be on a different subnet (i.e. 192.168.100.0/24 instead of 192.168.1.0/24 with all the trusted machines)?

  Read the article

• Printing to shared printers across VPN

  - by CYMR0

  I have a program that prints labels at five remote sites. Two sites, aren't working, but the rest are with an identical (as far as I can tell) setup. Using Wireshark, I have determined that the handshaking all goes well, but after the "Open Print File Response" the packet that is sent from the server, doesn't reach the client. But I'm a bit at a loss as to where I go from here. I know the port the packet was sent on (445) isn't being blocked, the RST packet gets sent on the same port and that gets there fine. It's also weird that the three out of five sites are working fine. This has been up and running for years without issue, all that we have changed is our connectivity (from DSL to bonded DSL). But this traffic is over a VPN - so it can't be the ISP interfering either can it? I'm totally stuck, and any help would be much appreciated. Thanks!

  Read the article

• SPAN/Port mirroring on Linksys switch

  - by Bastien974

  Hi all, I'm trying to deploy a Snort box in my LAN. I have a Linksys SRW248G4 and trying to configure Port mirroring so that Snort can listen everything on the network in promiscuous mode. So in ADMIN / Port Mirroring, I have 3 things: Source Port (e1,...e48, g1...g4) Type (Rx, Tx, Both) Target (e1...e48, g1...g4) Last time I played with it, I killed all traffic on the switch, I had to reboot it several times... so now I'm asking question before: Do I need to configure each Source Port (from 1 to 48) to forward to the single promiscuous port ? 48 rules !? Is that correct ? Thanks !

  Read the article

• Hosting provider that allows you to host your own VM image?

  - by Timo Geusch

  I've already looked at the 'Best Hosted VM Provider' question and checked the recommendations there, but I seem to have slightly odd requirements. Basically, I am looking for a host that allows me to host a VM image I supply (FreeBSD, which most of the suggested hosters don't support, they only seem to support various Linuxes) instead of one of their standard images. I'm a long time BSD user and have had colo BSD servers in the past so I'm pretty sure that i don't need much in the way of software support, but I'd basically like to run my server on managed hardware without having to rent the whole server. For the usage I have that would way OTT as we're talking a couple of small apps with very few users, a couple of blogs and (most importantly) email hosting for about 6-10 domains with moderate traffic levels. Oh, and reliability trumps cost to a certain extent.

  Read the article

• What ports does Advantage Database Server need?

  - by asherber

  I have an application which uses ADS and I am attempting to deploy it in a Windows network environment with a rather restrictive firewall. I am having a problem configuring firewall ports appropriately. ADS lives on \\server, and it's listening on port 1234. When \\client tries to connect to \\server\tables, I get Error 6420 (Discovery process failed). When \client tries to connect to \\server:1234\tables, I get error 6097, bad IP address specified in the connection path. \\server is pingable from \\client, and I can telnet to \server:1234. If I try to connect from a client machine inside the firewall, either connection path works fine. It seems there must be something else I need to open in the firewall. Any ideas? Thanks, Aaron. Edit: I should have specified that the firewall is open to \\server:1234 specifically for TCP traffic. Is UDP involved here in some way?

  Read the article

• OpenVPN Bridge on pfsense: once LAN pings clients, connectivity breaks

  - by Lucas Kauffman

  So I'm using a pfsense openvpn to bridge my LAN segment so VPN users can access the servers. The problem I'm having now is that I can establish a connection, I can ping the LAN server from the VPN, but as soon as I ping the client from the LAN server, there is no connectivity anymore between both parties. So: connect from the VPN client to the LAN = works ping the LAN from the VPN client = works access server from the VPN (ssh, ftp,...) = works ping client from server = doesn't work ping LAN from the VPN client = doesn't work anymore My bridge has em1 and ovpns1 bridged. I noted with tcpdump that ICMP is reaching the bridge between LAN and the VPN segment. But it's not put onto the em1 interface for some reason. My pfsense is running on an ESXi host with th vSwitch port enabled in promiscious mode. Firewall rules allow in and outbound traffic regardless origin or destination.

  Read the article

• Recommended RAM and disc space for Oracle 11g on Windows

  - by Álvaro G. Vicario

  I need to provide the recommended amount of RAM and disc space (divided in two partitions) so the customer can create an appropriate virtual machine to run Oracle. All I could find in the documentation was a brief listing with minimum RAM and typical/advanced install types. The virtual machine will run latest Oracle Standard Edition One (11g release 2 so far) under Windows Server 2008 x64 and will host a reasonably low traffic web application. How much RAM and disc must I ask for in order to be safe? (Feel free to ask for further details if I've omitted something relevant.) Update: Rough estimations: Database size: 10 MB after installation Growth rate: +3MB per day on average Size of database 'active' data: (not sure of what this means, there's not actual archive so I guess all data is current) Amount of data written per second in peak hours: a few KB Number of client sessions: 3 or 4 at most Frequency and response size of most heavy requests: some reports make heavy table JOINS that need up to 20 seconds to complete but they won't return more than a few thousand rows with plain text. The app also handles BLOBs (typical size from 50KB to 200KB)

  Read the article

• Reviewing firewall rules

  - by chmeee

  I need to review firewall rules of a CheckPoint firewall for a customer (with 200+ rules). I have used FWDoc in the past to extract the rules and convert them to other formats but there was some errors with exclusions. I then analyze them manually to produce an improved version of the rules (usually in OOo Calc) with comments. I know there are several visualization techniques but they all go down to analyzing the traffic and I want static analysis. So I was wondering, what process do you follow to analyze firewall rules? What tools do you use (not only for Checkpoint)?

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• My internet connection just got really slow - How can I troubleshoot it?

  - by Walden

  A few days ago my connection became really slow. I have DSL which should be 3mb down and 768k up. I'm lucky if I get 768k down and 200k up. It sucks. I called my ISP, Verizon and they did some sort of line test and told me the problem was on my end. I rebooted my modem several times, like they told me. I'm not really sure why I even bothered calling them, the guy on the other end was just reading stuff out of a notebook - pretty useless. So, I checked my network traffic in windows resource monitor, and there doesn't seem to be anything there hogging the bandwidth. What else could be slowing my connection down on my PC? on my router? Something else?

  Read the article

• Creating an office network and monitoring all activity without a proxy

  - by Robert

  We are setting up our office network and would like to track all the websites visited by our employees. However, we would not like to use any proxy based solutions. Our work is highly dependent on applications in which you cannot configure a proxy. Hence, the approach we would like to follow is setting up a router inside a computer (something like this : http://www.techrepublic.com/article/configure-windows-server-2003-to-act-as-a-router/5844624) This will also allow us to attach multiple ethernet cards and have redundancy in internet connectivity with complete abstraction from the user about which connection is being used. But most importantly, since all the traffic will be going through the computer (configured as a router) I assume there will be a way to run packet analysis on all the request / responses being made. For example, list all the FTP servers connected to (port 21), give a graph of all the URLs visited per day by frequency. Is there already a software which does this ? Or is it possible to build something like this ?

  Read the article

• Dual WAN port on a WRT54GL

  - by pufferfish

  Is it possible to reconfigure one of the LAN ports on a WRT54GL (running Tomato firmware) to act as a second WAN port? I have the following networks: PPOE connection to ADSL modem (works fine on the normal WAN port) WiFi neighbourhood network (in 178.X.X.X range), via a Mikrotik routerboard which I'd like to put on the WAN side of the router. I'd then like to set up routing so than some traffic (172.X.X.X) is routed to the Mikrotik and the rest to the ADSL modem. p.s. for practical reasons, I can't use the Mikrotik as the firewall/router. Edit: It seems this can be done by editing iptables, can someone tell me exactly how?

  Read the article

• Accessing through VPN, which internet connection would be used

  - by Sriram

  I've a data card which has a limit of 2 GB up/download traffic per month. I've an office internet line which has an unlimited up/download. I've successfully connected to VPN using my data card and by changing certain configurations like DNS etc., have also been able to use my office line for internet (verified by doing a IP check - returns the static IP of our office). Now to my question - is it just a NAT which is happening or am I actually using my office line for all communication. Which one would reflect the usage/trace. The data card usage log at this moment does not reflect any usage (which is confusing since the VPN is over the data card connection). Further more (theoretically), would the net be any faster if my office line is let us say 8Mbps and the data card is 512kbps by doing this as against directly connecting the internet using the data card.

  Read the article

• Win7 Prof. Computer won't wake on lan via Magic Packet from outside network

  - by Michael

  Hi all. I just purchased a new computer running Windows 7 Professional x64. I'd like to save power by having it sleep after an hour, but I would also like to be able to Remote Desktop into it at my leisure. I set up a static IP and have port forwarding set up on the router. If the computer is awake, the RDP connection works just fine. I downloaded and installed Wake-On-Lan thanks to this article If I put my new computer to sleep and send the magic packet from my old computer inside of my home network it wakes up. If I do the same thing, however, from my work computer outside the network it does not. I figured the Firewall was blocking the incoming traffic, but nothing in the Windows Firewall logs points to this happening. I'm wondering if anyone has any suggestions or any tests I can run through in order to narrow down what the problem might be. Thanks in advance for any help you might be able to offer.

  Read the article

• Site to site VPN using RRAS from an untrusted network?

  - by DrZaiusApeLord

  Our remote office will be moving to a new space where internet will be provided. They'll be behind a router doing NAT (I do not have admin rights to this router). They will be sharing a printer with the other people on the LAN, but will need VPN to our network for email and file shares. I was thinking of just having them run the windows VPN client and connecting via PPTP like they do when they are off-site, but I have read that multiple PPTP connections from the same NAT'd address to the same destination doesn't work well or at all. I am thinking some kind of site-to-site VPN is needed so there is just one tunnel. Can I just put in a VPN gateway, set it to connect to our RRAS/PPTP server, and have them use it as their default gateway? Perhaps even use the local default gateway for internet traffic. If so, what VPN gateway/device is recommended for this? Or other solutions? Thanks.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >