Search Results

Search found 4769 results on 191 pages for 'nirmal ram'.

Page 139/191 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• Usb stick too slow to benchmark?

  - by user85340

  I have a Core 2 Duo [email protected] with 3GB RAM. After some time using XUbuntu 10.10 on an 8GB stick I decided to switch to 12.04 and put it onto a 32GB stick (Transcend). I use an EXT4 with no journalling, noatime etc set. /tmp and /run is using tmpfs. And it is REALLY slow. MUCH slower than the old Xubuntu on the 8GB stick. Starting takes minutes, all applications "fade" because they respond too slow. I first thought that the NVidia graphics card is responsible for this, because there seem to be some known problems with that. Doing the adjustment (uncheck the sync checkbox) did not help. I believe the root cause is that the access to the USB stick is extremely slow. Running the read benchmark of the disk utility then brought the message "disk is too slow to benchmark"! BUT: When I do the same benchmark with the live CD I get around 20MB read performance and have a very responsive system! So how can I find out what is going one here?

  Read the article

• Freeze on Boot WindowsXP

  - by kyle

  Ok first off I know I should have Windows 7 but i don't Its a really old computer and i'm not sure if it can run the latest OS of ubuntu but i'm trying any whay so here are my specs or what i could have gathered from the computer(viruses are every where and most of the drivers are gone) Specs OS WindowsXP(it isn't letting me know which one that is blocked) Graphics card(can't access device manger it is blocked also) graphics card is 2003-2004 era though ram 512mb last time i checked USB(Drivers Gone) Wireless Card(Drivers Gone) Lan Card(Drivers Gone) Audio(Drivers Gone) CD Drive (it runs and works but i can't check its properties that's blocked to) Computer Dell Inspiron 600m Good News I have the Driver CD for everything Bad News I Don't have the OS CD I know the Computer is trash but i want to flash it anyway and just install linux(ubuntu) The second problem is it doesn't even want to load the CD all the way it is just stuck at the Ubuntu Screen with all the bubbles orange and if i resart it just does it again. any help would be nice. EDIT: okay i tried the first comment and it said i need a firmware file from http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware the firmware is b43/ucode5.fw, b43-open/ucode5.fw is there any other way of installing this firmware without being in the Ubuntu because what I have read is I need to be in Ubuntu to do this... Thanks for all the help you are giving me i have read your comments but i don't want to wait another two hours downloading that if i can get it working on this...

  Read the article

• Web hosting company basically forces me to use their domain name [closed]

  - by Jinx

  I've recently stumbled upon an unusual problem with one of hosting companies called giga-international.com. Anyway, I've ordered com.hr domain from Croatian domain name registration company, and my client insisted on using this host provider as couple of his friends already are hosted with them. I thought something was fishy when the first result on Google for Giga International was this little forum rant instead of their webpage. When I was checking their services they listed many features etc... space available, bandwidth etc. I just wanted to check how much ram do I get for my PHP scripts so I emailed them, and they told me that was company secret. Seriously? Anyway, since my client still insisted on hosting with them I've bought their Webspace package. During registration I had to choose free domain name because I couldn't advance registration without it. Nowhere was said, not even in general terms and conditions that I wouldn't be able to change that domain name. At least not for double the price of domain name per year. They said I can either move my domain name over to them (and pay them domain registration), or pay them 1 Euro per month for managing a DNS entry. On any previous hosting solution I was able to manage my domain names just by pointing my domain to their name servers, and this is something completely new and absurd for me. They also said that usual approach is not possible because of security and hardware limitations. I'd like to know what you guys think about this case, and should I report, and where should I report this case. In short. They forced me to register free domain name which doesn't suit my needs in order to register for their webspace package, and refuse to change domain name for my account until I either transfer domain to them or pay them DNS management which costs double the price of the domain name per year.

  Read the article

• IIS 7 SSO stops working during high CPU load? [migrated]

  - by DanB

  On our IIS7 site (Windows 2008 Server), we have set up single sign-on (SSO). It seems to work fine most of the time, but when the CPU load becomes high, SSO authentication completely stops working. I did some research and tried this suggestion to increase the max number of worker processes in the default app pool, but the increase did not help. Some details: The site is a WordPress blog. The server has plenty of RAM (2 GB) and free disk space. SSO is achieved by putting a copy of the WordPress login page (wp-login.php) into a subfolder below the root that has anonymous authentication disabled, and then redirecting the browser to it. This was the recommendation of Microsoft given to our consultants. To increase CPU load for testing, I have three scripts hit the home page simultaneously, over and over. This drives CPU to 100%. When these scripts are running, SSO authentication simply doesn't happen. As soon as I stop the scripts, SSO works again. (I should mention that the SSO problem also happens when many users visit the site at once....) The WordPress database process (mysqld) is not stressed at all by the scripts. I would be happy to provide further diagnostics. Any help appreciated!

  Read the article

• Why is my USB data transfer so slow?

  - by Dave M G

  Whenever I do any kind of file transfer using USB, whether to a USB stick, or with my Android phone, or anything else, it is ridiculously slow. It says 59.8 KB/sec, which would be an awesome speed if this were 1991 and I was using a modem to dial up to my local BBS. Surely USB technology is better than that...? 37 seconds to move less data than the equivelent of 1 MP3 file? Also, regardless of what it says about speed and time, the reality is much, much slower. I routinely see it say something like "37 seconds left" and have to wait for minutes. Sometimes, if I want to move large amounts of files, it can say it will take 8 hours or more. Is this normal? My computer may not be the most awesome on the market, and about a year old, but it's an i5 with 4GB RAM and modern components, so surely this isn't the hardware's fault. What can I do to get better USB data transfer performance? Also, I did look at this question, but my newbie eyes don't see anything that look like an actual solution, just a lot of discussion about what transfer rates could or should be. Update: As requested in the comments, I've generated a whole bunch of output from the command line, and put it on Ubuntu Pastebin. Please see it here.

  Read the article

• Moving to New Machine... also upgrade to 64bit. What steps?

  - by Kendor

  I am about to move to a new Lenovo X201 from current X61. Current setup has separate \home, separate swap file, also separate \Data partition. Am currently running 10.04 32 bit. Am considering running 64 bit on new machine because I will now have 8 GB of RAM. And would like to also move to 10.10. Ideally I would like preserve as much of my current setup as possible... New machine has Win7 on it, but will blow that away, as I've made a clonezilla copy of it, and will use VirtualBox for when I need Windows. Can someone suggest a good step by step for me? I'm networked to a NAS and also have plenty of external USB storage in case I need intermediary steps. So do I set up new machine first with 64bit 10.10, with partition scheme I want? then rsnyc over \home from old machine (over write target home)? Do I need to upgrade the X61 first to 10.10?

  Read the article

• Will all applications work fine on 64-bit Ubuntu?

  - by Qmal

  I used Ubuntu some time ago and now I want to switch on it again since community raised a lot and so did support for applications like Wine. I remember that when 64bit version just came out many applications didn't work as they did on 32bit version. Is it not better or still the same? Maybe they implemented something like WoW in Windows that simulates 32bit architecture and every possible app is working just fine. I am asking because I have lots of ram and I don't want to sit on 3GB when I have 8. Also, I am somewhat of a programmer, but that is not a problem because if I write PHP I use NetBeans on Windows anyway, and it works on Linux just as fine. But I also love to write C++/C# code. Is it well supported? I really like Visual Studio 2010, it is very slick and has good auto completion, debugging and so on... Is there any IDE on Ubuntu that is similar to Visual Studio in terms of auto-completion, code formatting, GUI designer, debugging? I really hope you will answer me these questions because I really like to "convert" myself to Ubuntu once and for all.

  Read the article

• Issue with increasing the root partition from the swap

  - by user211761

  I have an issue with increase the size of my root partition. I have ElementaryOS Luna, and while installing it asked me how much space I want to use. I choosed 15 GB for it, because I want to use this as an alternative system. The issue is that after the installation was complete, I found out that my root partition is only 7 GB big, and SWAP is 8 GB which is useless cuz I have 8 GB of RAM. Now I want to shrink the swap and increase the size of my root partition, so I booted the LiveCD and used GParted. I shrinked the swap without any problems, but now I cant add that free space to any partition. I also turned Swap off. I would add a picture, but I need at least 10 reputation to post images ( Stupid ) Its also worth mentioning that in Gparted its showing my partition in a different way. I would post an image BUT I CANT, so I need to write it down. Its something like this [Pointing arrow down] /dev/sda4 Extended /dev/sda5 ntfs /dev/sda6 ext4 (Which is my main partition) /dev/sda7 linux-swap unallocated Picture:

  Read the article

• 11.10 system crashes for no apparent reason [closed]

  - by varanoid

  I'm relatively new to Linux, and while I know a fair amount about computers and programming, it certainly isn't my specialty. I have a dual boot with Windows 7, and it has been working very well for me until recently. Just randomly the computer will freeze. The last time I was smart enough to keep the System Monitor open when it happened, and it looks like at the time of freezing "bash" and a bunch of other processes that I don't recognize seem to have flooded the memory. So it looks like my memory is getting overloaded and this is what is crashing the system, but I honestly have no idea what could be doing it. Generally I have a bunch of programs running, but they don't take much RAM or CPU: Transmission, Libre Office Writer, Firefox, Empathy, and Banshee. Sometimes I also have Text Editor and Terminal open, but it crashes regardless. When it crashes, it seems that all of the programs are working fine but things like windows, the taskbar, and operations like Alt+Tab just stop working properly or at all. Sometimes the mouse and keyboard freeze and I have to power off manually. Other than that I don't know what the problem is. The only irregularity I've experienced is that I can't download "Debian package management system" even though other updates download fine.

  Read the article

• How Do Computers Work? [closed]

  - by Rob P.

  This is almost embarrassing ask...I have a degree in Computer Science (and a second one in progress). I've worked as a full-time .NET Developer for nearly five years. I generally seem competent at what I do. But I Don't Know How Computers Work! Please, bare with me for a second. A quick Google of 'How a Computer Works' will yield lots and lots of results, but I struggled to find one that really answered what I'm looking for. I realize this is a huge, huge question, so really, if you can just give me some keywords or some direction. I know there are components....the power supply, the motherboard, ram, CPU, etc...and I get the 'general idea' of what they do. But I really don't understand how you go from a line of code like Console.Readline() in .NET (or Java or C++) and have it actually do stuff. Sure, I'm vaguely aware of MSIL (in the case of .NET), and that some magic happens with the JIT compiler and it turns into native code (I think). I'm told Java is similar, and C++ cuts out the middle step. I've done some mainframe assembly, it was a few years back now. I remember there were some instructions and some CPU registers, and I wrote code....and then some magic happened....and my program would work (or crash). From what I understand, an 'Emulator' would simulate what happens when you call an instruction and it would update the CPU registers; but what makes those instructions work the way they do? Does this turn into an Electronics question and not a 'Computer' question? I'm guessing there isn't any practical reason for me to understand this, but I feel like I should be able to. (Yes, this is what happens when you spend a day with a small child. It takes them about 10 minutes and five iterations of asking 'Why?' for you to realize how much you don't know)

  Read the article

• I have Ubuntu only and need to install Windows

  - by Terzuz

  I had Windows 8, I installed Ubuntu for a new OS, Then I want to sadly go back to Windows , I have a Windows Vista *.iso but I can't boot from it. When I try to extract the '.iso file and have the contents on my USB so it can boot up , When I restart and click F9 for my Boot Device Options , Only my Hard Drive and CD ROM are there but my "Generic Flash Drive" is not , But when I do not have Windows Vista '.iso on it , It will show up in the list. How can I make a partition of some sort, Provide instructions since I am new at this all , then I need to be able to use the Windows Vista installer and install Windows Vista, I would like Dual-Boot if possible. Info: I have the HP 2000 Laptop (Mine was removed from the Best Buy Website so the closest laptop to the specifications and the design is the link at the bottom) I am running Ubuntu 12.10. I have 4GB of RAM , 220 GB in my Hard Drive left , I have a USB Flash Drive which works sometimes , other times it fails. Note - I tried using GParted in Ubuntu but I had a problem where the main drive with 220 GB Free was locked , I am not sure what to do and can not find the correct forum. http://www.bestbuy.com/site/HP+-+Pavilion+15.6"+Laptop+-+4GB+Memory+-+320GB+Hard+Drive+-+Pewter/5043836.p?id=1218608951204&skuId=5043836

  Read the article

• Where to find information about ubuntu compatible or certified hardware/PC models

  - by Halkinn

  I am buying a new desktop PC in early 2013, anyway this question should apply to someone intending to buy a new laptop/ultrabook as well. This machine is not meant for gaming, and if I ocasionally do it, I can survive with minimum graphics. However I may need some heavy multimedia edition or multitasking at times, so basically my greatest priority is a good processor, after that perhaps average graphic card (if onboards are not enough, I am still not informed enough about that), at least 4GB of RAM with possibility of expansion. I know there are some PC models specially designed to ship with Ubuntu, which is the OS I use the most these days. However, most people around me use Windows and some software with unsupported versions for Linux and not having a Windows license becomes a bit problematic. Given that, I would like to find information about which PC models or even manufacters currently on the market have the best compatibility with Ubuntu, I am still undecided between building my own desktop or buying a pre-made model, so I would like to find information both for certified models and certified hardware or even Ubuntu partners that may work closely with Canonical. Where to find this information in order to make sure that I will have a good experience with Ubuntu on my new PC in the years to come?

  Read the article

• Do i need to restore iptable rules everytime on boot?

  - by capdragon

  Every time i reboot i loose the iptables rules that took me sooo long to enter. I know i can save them and restore them on boot but is there anyway to save them forever? Do i really need to restore them on boot every time? Seriously? The problem is I have a HUGE list of IPs in which i use a while loop to load them in. This can take upwards of 10 minutes. This is my home FTP server. It's a small vm with 1gb ram and very little processing power. There are so many IPs because I've pretty much given up on the Asian continent. I don't need them to be hitting up my ftp server everyday with brute force. I also block gov. monitors, trackers and spammers. This is the while loop i use to load in the list. grep INPUT block.list | while read LISTA; do sudo iptables -A $LISTA; done

  Read the article

• Enabling GTX 570

  - by Silas

  Hello i just built up my new system: Asus Rock Z77 Extreme 4 Intel i7 3770k 16 Gb Corsair Ram Zotac Nvidia GTX 570 bequiet! 630W Power supply 120 GB SSD So after i installed UBUNTU 12.04 64 bit. It ran smoothly. I downloaded and installed all the recommended updates. After checking the Sytem details the GTX 570 didnt show up as graphics unit. so i figured i needed to download the drivers. So i did but being a complete newbie to linux i didnt succeed in installing them. (I think) Anyway after several tries and errors i shut down the PC and restarted it. Resultung in do Signal to my screen after trying to reboot and all the monitor outs with no result i took out the graphic card and now it boots normally but after booting it says there is a problem with the system the graphics cant be recognized something something. So Question A: What do i do? I Like linux but the arbitrarity of the Errors that occur without any changes to the system scare me. Question B: Is there A beginners guide to Ubuntu where i could start from scratch because i really want this to work? Question C: Now that the System is (suddently) showing these graphic errors So far without visible consequence despite the error message. should i reinstall the GPU and give the driver installation another try or the other way around? Ill be very grateful for any help. Thank you in advance!

  Read the article

• Is there a PROPRIETARY driver (NVIDIA or ATI) that actually works with 12.10?

  - by DS13

  NOTE: I see many similar topics on this, but I've tried all their suggestions, and nothing has worked. THE MAIN DIFFERENCE SEEMS TO BE: I always get a black screen with a blinking cursor, while others seem to get through the boot-up and see distorted graphics or just their wallpaper. ISSUE: I do a clean install of Ubuntu 12.10. Boots fine with the “nouveau” graphics driver – graphics (even just menus) are very slow, choppy, and distorted. The three other driver options in Ubuntu (official NVIDIA drivers), all result in a variation of the black screen on boot up. There will be NO access to a command line/GUI in anyway what-so-ever (tried every option recommended out there, but the system is unusable at this stage). I can only reinstall, and try different drivers…and I only ever get one shot at it. QUESTIONS: -Does anyone know of a PROPRIETARY driver that will actually work on 12.10 with a NVIDIA or ATI card? -Should I just buy a newer graphics card to put in as a replacement? MORE INFO: This is my second computer, and I’m just trying to get a working install of Ubuntu on it. I don’t want to put much money into it, as I have seen Ubuntu run great on much older/less capable machines. I’ve got a decent'ish Core2Duo Intel processor (2.13Ghz), 2GB of RAM, 320GB hard drive, 32-bit architecture, and there is no other O/S installed. It appears as if the graphics card (NVIDIA Geforce 7350 LE) is holding me back. TRIED SO FAR: -all drivers available in Ubuntu *all fail -manual install of some different NVIDIA drivers *all fail -also tried installing the generic kernel, Nvidia driver doesn't work in 12.10 *no difference -tried installing 12.04 *same results -every method suggested to at least get a command line after switching to a NVIDIA driver *all fail -UPDATE- Re-tried everything above with a new NVIDIA Geforce 210...same results for everything. -UPDATE #2- Re-tried everything above with a new AMD Radeon HD 6450...installed the proprietary driver from Ubuntu's "Software Sources" menu...EVERYTHING NOW WORKS. See "answer" below for summary.

  Read the article

• Tuning WebServer Response -

  - by Vedran Wex Maricevic

  I have this sam e question on StackOverflow and I was advised to ask it here hoping for more information. Here is the question: I am in rather unfavorable situation. I have aspdotneststore front e-commerce application and search addon called VibeTrib. I dont have source code for both of those. Store that runs on StoreFront and VibeTrib has close to 250k products. Also we have lots of filters. I spoke to ViTrib reps, and they want extra money so they could optimize Queries that they use. Money they require is nto a big deal, but the problem is I dont trust them anymore. What we got is much different then wha is being advertised. To cut the long story short. I am runing the store on Amazon AWS now, and regardless of what DB (MsSQL 2012) server I set (I tried 32GB RAM monsters instances) it is slow. Ajax search uses Full Text search and it displays search keywords relatively fast, but once the search is performed ( to display all results) it is still slow.!!! There is something that I could to do accelerate the speed on my own end? I do have full control over EC2 Instance (Web server Server 2012 and IIS 8). Can I set IIS to step in for the search and cache some of it? I was hoping to cache at least some most common words. My best bet is IIS 8 :) Is there any help in my case? Thanks

  Read the article

• Been doing .NET for several years and am thinking about a platform change. Where do people suggest I go?

  - by rsteckly

  Hi, I've been programming in .NET for several years now and am thinking maybe its time to do a platform switch. Any suggestions about which platform would be the best to learn? I've been thinking about going back to C++ development or just focusing on T-SQL within the Microsoft stack. I'm thinking of switching because: a) I feel that the .NET platform is increasingly becoming commodified--meaning that its more about learning a GUI and certain things to click around than really understanding programming. I'm concerned that this will lend itself to making developers on that stack increasingly paid less. b) It's very frustrating to spend your entire day essentially debugging something that should work but doesn't. Usually, Microsoft releases something that suggests anyone can just click here and there and poof there's your application. Most of the time it doesn't work and winds up sucking so much more time than it was supposed to save. c) I recently led a team in a small startup to build a WPF application. We were really hit hard with people complaining about having to download the runtime. Our code was also not portable to any other platform. Added to which, the ram usage and slowness to load of the app was remarkable for its size. I researched it and we could not find a way to optimize it. d) I'm a little concerned about being wedded to the Windows platform. What are the pros and cons of adding another platform and which platform do people suggest? Thanks!

  Read the article

• Efficient Algorithm for Recording gameplay's objects positions

  - by Scorch

  So, I have a game idea in mind, and for that I need to record the game around the player. I'me not talking about recording it as video, but rather recording the scene objects, and their positions within the game, and then render them, giving the player the ability to go back and forth, to stop time and move around. I've made a prototype with some data structures in C#, since this is going to be the programming language we'll be using in our game, but if we want the player to be able to go back just five minutes back with the data of just 100 NPC's, it takes almost 1GB of RAM. Right now, I'm just storing a Doubly linked list, each item with the object position. In the game, I'll need to store even more data in each node, so I need something even more ligher. Of course, this algorithm is zero optimized, but still, that is a lot. The alternatives would be create the NPC's that aren't really important to the game when the user is viewing the past, but I don't really like it very much for the sake of realism. I wonder if there is a better way to store this? Thanks in advance, Scorch

  Read the article

• Unable to start after 13.04 > 13.10 udate

  - by romainl

  At the end of the update process, clicking on the Restart button had no visible effect whatsoever. After waiting 5 to 10 minutes, I decided to reboot the computer manually. Since then, I rebooted a good dozen times (not with the hope that it would work but with the hope of reading the messages) with the same non-result and the same symptoms: I get the ASCII text-on-purple Ubuntu 13.10 . . . . splash screen with these messages: * Restoring resolver state... [OK] * Starting crash report submission daemon [OK] * Starting CUPS printing spooler/server [OK] Everything disappears. The whole process hangs at a purple screen with the mouse cursor right in the middle. At this point, I'm unable to use the mouse and the keyboard. Booting from a 12.04 CD works perfectly, Disk Utility says that all my disks are OK and I can mount my main partition without problems. Something obviously went wrong at the end of the upgrade but I have no idea what. I'd appreciate any pointer. This is the kind of moment where you really think "Next time, I'll separate my /home partition for sure". My machine is an aging but working Dell Inspiron 530 with an Intel Core Duo E2160 processor, 2 GHz of RAM and an ATI Radeon HD3650 video card. Thanks.

  Read the article

• Hitching and Slowness Due to HDD Activity on Ubuntu, But Not Windows?

  - by Espionage724

  It's been bothering me for months now, but I've noticed in Ubuntu (or any distro of Linux I've tried), any major I/O activity will cause hitching and general slowness. For example, if I try doing a file transfer from my network computer to the computer I'm using and try moving the mouse after a while, it might not respond for a second or so. Similar incidents occur in other cases too (right-clicking to get a context menu takes a few seconds, hitting the drop-down application bar takes a while, etc). My HDD isn't top-notch (a WD Blue 500GB 7200RPM drive) but I don't recall it being nearly this bad in Windows 7, 8, or 8.1. CPU activity during file transfers is relatively low (less than 10-20% on all cores of a Phenom II X4 @ 3.3Ghz). I'm using Gnome System Monitor (on Xubuntu) and can't seem to see what kind of HDD activity is occurring though. I have 8GB of RAM too, which is moderately being used (2.5GB), but shouldn't be a problem either. Any ideas what's up? I've tried kernels between 3.8 and 3.11 (i'm using saucy currently with 3.11).

  Read the article

• Less graphics power all the sudden (Intel HD 3000)

  - by queueoverflow

  I have a Intel Sandy Bridge i5 with the HD 3000 graphics card. I used to be able to play Urban Terror and Nexuiz comfortably with 85 and 60 frames per seconds until mid/end of October 2012, the former even on a full HD display with that many frames. Now I have around 30 to 45 on the smaller laptop screen and around 20 to 30 on the external monitor. Did something happen to Kubuntu 12.04 so that it has less graphics performance than previously? Update I looked into the system monitor and could not detect anything being at the maximum. The four CPU cores were pretty much bored, the 8 GB RAM were filled with maybe 2 GB. And I ran intel_cpu_top and did not notice anything at its limit. See the output. after Kernel bisecting I now did a kernel bisect and tried 3.2.0-23, 3.2.0-27, 3.2.0-29 and 3.2.0-30 and all had full graphics power. Interestingly, I then had full power when I just booted back into the regular 3.2.0-32 kernel. This does not make sense to me …

  Read the article

• Ubuntu audio mysteriously stopped working (12.04)

  - by Laika

  Well, I've been a user of Ubuntu 12.04 LTS since April now, and it's been a very pleasant experience. I'm a big fan of electronic music, and I tend to have my tracks playing in the background while I do things on my laptop, either in YouTube or in Clementine, my default music player. All has worked very well until now. A couple of days ago my entire PC started to lag really badly. Almost everything was unusable. I opened up System Monitor via the terminal to find a process called "pulseaudio" using nearly 1GB of RAM and over 80% of my CPU. I needed to get some important work done and so I killed the process without thinking. Once again today, pulseaudio decided to lag the hell out of my PC, and so I killed it again. Nothing seemed to happen immediately, but once I opened up YouTube all the audio on videos stuttered a lot, while the videos played smoothly. I restarted Firefox to find that the audio was now not working at all, with both headphones and speakers, and the volume up quite a bit (it's not muted, I've checked that!). A little bit of research later and I've discovered that pulseaudio plays an important part in Ubuntu's audio. Even after restarting my PC the audio still ceases to work in any applications or with any output. The pulseaudio process refuses to start up again. So, can you help me out here? What can I do to fix my problem, and why was pulseaudio doing this in the first place?

  Read the article

• How can I speed up boot on one of my machines?

  - by Korneel Bouman

  I have a Gateway all in one machine (2 gig Intel Core 2 Duo T7250 dual core processor, 2 gig RAM - full specs) on which I installed 10.10. Once it has booted it's fine, but it takes forever to boot. This is what happens: 1. Boot starts with cursor flashing for about 10-15 seconds 2. Cursor disappears for 1.5 - 2 minutes 3. Cursor reappears, blinks a few seconds more, boot finishes in another 10 seconds 4. Login screen I have another machine with marginal better specs that boots up in no time (basically the above minus the two minute delay). Things I've done: enabled verbose mode for grub nothing is showing until after 2 minute pause. checked syslog last message before pause is a message from alsa saying the process is already running (or something similar... going from memory here...) It could be something sound related as the built in speakers are not working (sound card is recognized though and headphones work). Anyway, it's not the end of the world, but it's annoying and I'd like to know what's going on... Many thanks, and let me know if more info is needed.

  Read the article

• Ubuntu 11.10 very slow compared to Windows

  - by Patrick

  I'm new to Ubuntu/linux. Since my PC is very old and not very fast with Windows 7, I decided to give Ubuntu a try, so I downloaded and installed Ubuntu 11.10 today. When I first started it, I had bad 800x600 resolution and it was very slow and annoying. So I installed a driver for my graphic card and now everything looks very nice (1280x1024).But I think it's still far slower than Windows 7. I tried to run in Ubuntu like a few people suggested on the forum but if I log in I get a black screen saying something like "this video mode cannot be displayed". I get that same screen when booting Ubuntu btw, but after about 15 seconds it disappears and just starts Ubuntu. I also installed other drivers for my graphic card but everything stayed the same. I noticed that i.e. when I open Firefox or system settings it takes about 5 seconds till it opens (while Windows 7 takes under 1 second to start i.e. Chrome) and when I do this my CPU usage gets to 100% for a short time. Computer specs: Memory: 2GB RAM Processor: Intel Pentium 4 2.8GHz Graphics Card: Nvidia GeForce 6800 400MHz. I read on various forums that 11.04 works flawless on many PCs, where 11.10 is very slow. Should I install 11.04 or could anybody help me with this problem?

  Read the article

• ADF Hands on Training &ndash; Prerequisites for 22nd March 2011

  - by Grant Ronald

  For those of you coming to the ADF Hands on training on the 22nd March in London, there was a link to the prerequisites.  Unfortunately, in a reshuffle of content on OTN, this page was removed.  So, over the next day or so I’m hoping to the pull together the relevant information into this blog post.  So keep checking back! Firstly, you need to being your laptop with you to do the hands on exercises.  No laptop, no hands on. Recommended 2GB RAM running Microsoft Windows XP SP2, 2003 Server SP2, Vista (32 bit only), Windows 7 or Linux or Mac 2GHz Processor (less will be acceptable but slower) Mozilla Firefox 2.0 or higher, Internet Explorer 7 or higher, Safari 3.0 and higher, Google Chrome 1.0 or higher Winzip or other extracting software Adobe Acrobat reader Flash (if you want to see dynamic graphs in your application) As for software, you will need have installed JDeveloper 11g.  The hands on instructions are based on 11.1.1.2 (or is it 11.1.1.3)! anyway, either of those or 11.1.1.4 would be required. You also need an Oracle database on your machine and access to the HR schema (which should be unlocked).  Don’t expect to have access to a network and VPN to a database. A simple test, unplug your laptop from your corporate network, run up JDev  and select File –> New –> Database connection and make sure you can connect to HR database and see the Emp/Dept etc tables.  If you can do that, you should be good to go. I would strongly recommend ensuring you have this in place before you arrive on Tuesday. Look forward to seeing you there.

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >