Search Results

Search found 6674 results on 267 pages for 'signal handling'.

Page 139/267 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• Multicasting and multicast address

  - by Zia ur Rahman

  I have confusion about the multicast addresses, I have read an example which is given by. Suppose two applications have been built to send audio over a network. One application accepts and digitizes an audio input stream, and then sends the resulting frame across the network to other application. The second application receives the digitized audio from the network, converts it back to the audio signal and plays the result over a speaker. Unless the two applications use broadcast to send frames, no other computers on the network will receive a copy of the frame. Multicasting provides an excellent solution to the problems of allowing some computers to participate in audio transmission. To use multicasting , a multicast address must be chosen for the audio application. And the receiving application passes the multicast address to the network interface. The interface begins to accept the packets sent to that address. Question: how this multicast address is chosen, how the receiving application knows that the sender using this specific destination address for the audio frames.

  Read the article

• Wake on Lan/Wan won't work after some time has passsed

  - by Vian Esterhuizen

  I have the following set up: Gigabyte Z77X-UD5H Wake On Lan Enabled Asus N66U Port Forwarding Static IP assigned to my computer Windows 7 Advanced Power Management - PCI Express - Off Intel 82579V - All options under Power Management checked I'm trying to set this up for Wake on Wan capabilities. If I shut down my computer and immediately try to Wake on Wan (and Lan) it works and starts up. While the computer is on, I've used a few WOL specific packet sniffers and the packet comes through on the correct port. After any period of time over a few minutes, waking on Wan or Lan won't work. The back "activity" light is blinking on my ethernet port on my computer, as well as on the router, so I would assume the network card is on and able to receive a signal. Any ideas? Suggestions? What can I do to troubleshoot the problem?

  Read the article

• DokuWiki Segmentation Fault On Radius Auth

  - by mrduclaw

  I'm running x64 Ubuntu 12.04. I did a simple apt-get install dokuwiki to install DokuWiki. And I'm trying to follow the directions located here: http://www.dokuwiki.org/auth:radius to get Radius authentication working. Things seemed to install OK. Under Configuration Manager I selected Authentication backend to be "Radius" and filled in the Radius details at the bottom. Now, however, whenever I try to log into the Wiki, my browser gives me the following error: No data received I checked /var/log/apache2/error.log and see this: [Tue Jul 10 22:22:14 2012] [notice] child pid 5270 exit signal Segmentation fault (11) I'm fairly sure the Radius server is setup correctly as it correctly authenticates with my squid proxy and other stuff on the network. But this is about the extent of my Linux troubleshooting skills. Can anyone suggest steps for me to follow to help track down what's causing apache2 to segfault short of attaching with gdb and issuing a set follow-fork-mode? I'm also open to just hearing suggestions for simila

  Read the article

• Postfix TLS issue

  - by HTF

  I'm trying to enable TLS on Postfix but the daemon is crashing: Sep 16 16:00:38 core postfix/master[1689]: warning: process /usr/libexec/postfix/smtpd pid 1694 killed by signal 11 Sep 16 16:00:38 core postfix/master[1689]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling CentOS 6.3 x86_64 # postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 disable_vrfy_command = yes home_mailbox = Maildir/ html_directory = no inet_interfaces = all inet_protocols = all local_recipient_maps = mail_owner = postfix mailbox_command = mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost mydomain = domain.com myhostname = mail.domain.com mynetworks = 127.0.0.0/8 myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relay_domains = sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_tls_note_starttls_offer = yes smtp_tls_session_cache_database = btree:/var/lib/postfix/smtpd_tls_cache.db smtp_use_tls = yes smtpd_delay_reject = yes smtpd_error_sleep_time = 1s smtpd_hard_error_limit = 20 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_pipelining, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_invalid_hostname, reject_non_fqdn_hostname, reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_destination reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.spamcop.net, permit smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_sender_restrictions = permit_mynetworks, reject_non_fqdn_sender, reject_unknown_sender_domain, permit smtpd_soft_error_limit = 10 smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s smtpd_use_tls = yes tls_random_source = dev:/dev/urandom unknown_local_recipient_reject_code = 550

  Read the article

• Prevent audio recording applications from picking up non-microphone audio output

  - by hheimbuerger

  When talking to people over Mumble/Teamspeak/Ventrilo, I have a few who are broadcasting all of their audio output (e.g. music playing in the background, game sounds, etc.) whenever they are sending -- in addition to the microphone signal. I don't have this problem myself, so it's hard for me to troubleshoot remotely, but I'm interested in collecting solutions for this problem for Windows XP, Vista and 7, so that I can link them to this question. Links to other related SU questions are highly welcome as well, but I couldn't find any. Most people seem to try to either get microphone to feed back into the audio output or turn exactly that off, which is different from this problem. I'm talking about the opposite problem, the output being fed into the input.

  Read the article

• Redirect output of Python program to /dev/null

  - by STM

  I have a Python executable, written and compiled by somebody else, that I simply need to run once halfway down my own bash script. The program uses a text-based UI, therefore waits for input before proceeding, but the key operations it performs when starting are required in my bash script. A messy (and strange) procedure I know, but unfortunately I haven't got any other options. I've gotten around forcefully closing the program with a kill signal, but the program's TUI insists on outputting to wherever it's run. I've tried redirecting both stdout and stderr to /dev/null and running the program in the background by suffixing an ampersand, but simply can't get it to play ball. I believe the cause is the program spawns other processes, and the output redirection of the parent process doesn't affect them. Is there any trick I can utilise to redirect all output from child processes too?

  Read the article

• Setting up a linux server to share an internet connection.

  - by Skizz

  I in the process of reconfiguring my network. It is currently like this: internet - modem - wireless router - wired server/clients | |---- wireless clients but I need to move the router to get a better signal for the wireless clients. So, I'm looking at this: internet - modem - server - switch - wired clients | |---- wireless router - wireless clients How do I set up the server to enable this? Also, what set ups do the clients need. The server is Ubuntu 9.04 and the clients are a mix of Windows XP / 7, Ubuntu and printers. I believe this new set up will allow me to control access to the internet, which would be useful.

  Read the article

• Why is my ipad's wireless so flakey?

  - by Mark

  I'm the proud owner of a new IPad here in the UK. All is good, except for the wifi, which is a bit flakey. It connects fine to my Draytek router which is set for WPA/WPA2 and 56g only, displaying full signal strength. Then, after a few minutes, it goes down to minimum strength... And sometimes it goes back up again. A few times, it seems to loose connection completely, and needs to be turned off and on again. I've looked at the Apple support site, and have tried their recommendations (which are not really very relevant), but still nothing. I've tried setting the router to wpa2 only, and setting long-preamble. Right now, I guess I want to know if it's a hardware problem with my device and should be returned, or if it's a problem with all ipads which will be resolved. Guess I could take it back to the Mac genius bar, but I find those guys so incredibly pretentious and, frankly, rather useless, that i'd rather wait until I've exercised other options!

  Read the article

• Apache Serving 403 Forbidden after OS X Snow Leopard Upgrade to Version 10.6.6

  - by Ian Oxley

  I've just upgraded my MacBook Pro to OS X Snow Leopard version 10.6.6 and now Apache is misbehaving: requests to http://localhost/ generate a 403 Forbidden response -- FIXED requests to any of my virtual hosts seem to generate a 200 Ok response, but contain zero bytes Some further info that might be useful: I'm using the Apache that comes bundled with OS X. I'm using PHP from http://www.entropy.ch/software/macosx/php/ (which is in /usr/local/bin) I've had look at the Apache error log and the only error seems to be the following: [notice] child pid 744 exit signal Segmentation fault (11) I'm completely stumped by this. Any help would be much appreciated. UPDATE Ok, I've managed to resolve the 403 Forbidden error thanks to http://techtrouts.com/mac-os-x-105-web-sharing-forbidden-403-on-httplocalhostusername/ I'm still having the second problem though for any request e.g. this now happens when I request http://localhost

  Read the article

• Annex-A vs Annex-B ADSL splitters

  - by Odys

  While trying to improve our Adsl connection, I found that we use a splitter that is from an unknown ventor and have no clue whether is for AnnexA (PSTN) or AnnexB (ISDN) line. Is it possible that somebody used the wrong splitter and just because it connected nobody ever cared? We have an ISDN line but the splitter used is blank. I am not really sure if it is AnnexB. Would it be possible to use an AnnexA filter over an ISDN line (even with that much signal loss)? (I am posting here because this is about our connection to the rack, I'm not sure if there is a more proper SExchange site)

  Read the article

• When a python process is killed on OSX, why doesn't it kill the child processes?

  - by Hugh

  I found myself getting very confused a while back by some changes that I found when moving Python scripts from Linux over to OSX... On Linux, if a python script has called os.system(), and the calling process is killed, the called process will be killed at the same time. On OSX, however, if the main process is killed, anything that it launched is left behind. Is there something somewhere in OSX/Python where I can change this behaviour? This is causing problems on our render farm, where the processes can be killed from the management GUI, but the top level process is really just a wrapper, so, while the render farm management might think that the process has gone and the machine is freed up for another task, the actual processor-intensive task is still running, which can lead to huge blockages. I know that I could write more logic to catch the kill signal and pass it on to the child processes, but I was hoping that it might be something that could be enabled at a lower level.

  Read the article

• Computer to Tv cable question

  - by Keith D

  Hi all. Heres my query : I have a PC with all the usual outputs and a couple of TVs in the house with inputs to connect to a computer. Now, what i would like to do is get rid of cable TV and using the input into the spliters in the basement,( ie. where the input cable from outside actually feeds the system ) have the computer become the "Cable supplier" ( so to speak ) and have the output ( via some sort of box ) from the computer, convert what is on my monitor into an RF signal that is then fed into the cables in my house and ultimately to each TV / room . I don't know if there is such an item but would welcome any thoughts you might have on such a set up. I am not into HD or the like, so the picture quality needs only to be watchable, not HD. I don't want to have to set up seperate cables to feed the audio on each TV. Thanks in advance!

  Read the article

• Revo 3610 not doing hdmi handshake

  - by DoomStone

  I am having a problem with my Revo 3610 witch is connected to my tv via hdmi. For some reason will it not do the hdmi handshake with the tv, so my tv does not think that there are anything in the hdmi port. I have tested the tv and it works find, with my laptop and dvd. It dose work some times, but this time have it failed for 2 days in a row, and i have tried rebooting, turning the tv off and on, and so on nothing helps. I can trick the TV to listen to the HDMI with connecting with my laptop and then change the hdmi back to my revo, this on the other hand results in the image going thoug nicely but there are a big fat "Check signal cable." on the screen. I have also tryed changing the resolution in the revo but this dose not help ether. Have any one had this problem before, and if so how did you fix it? Example: http://i.imgur.com/gguZ4.jpg

  Read the article

• Dell U271 monitor DisplayPort suddenly not working

  - by Amir Latif

  My new(ish) Dell U271 took a bit of a knock and it now suddenly doesn't recognise the Macbook plugged into it via DisplayPort - this had been working great for several months up until now. When I "Scan Sources", it doesn't find anything on DisplayPort. However, one suspicious behaviour leads me to think all might not be lost. When the Mac is woken from sleep, this used to kick the monitor in (as an monitor would) and while it no longer does that, the light on the monitor does go from standby orange to blue briefly, then the monitor says it's going into "power save" mode. It seems like it gets some kinda signal. Any ideas on how I can diagnose the problem? I'm trying to find another mac but no one near me has one ...

  Read the article

• Why do I have no TTY on a basic Ubuntu 9.10 server install?

  - by pr1001

  I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

  Read the article

• Initiate a PHP class where class name is a variable

  - by ed209

  I need some help with an error I have not encountered before and can't seem to find anywhere. In a PHP mvc framework (just from a tutorial) I have the following: // Initiate the class $className = 'Controller_' . ucfirst($controller); if (class_exists($className)) { $controller = new $className($this->registry); } $className is showing the correct class name (case is also correct). But when I run it I get this in the apache error log (no php error) [Wed Mar 31 10:34:12 2010] [notice] child pid 987 exit signal Segmentation fault (11) Process id is different on every call. I am running PHP 5.3.0 on os x 10.6. This site seems to work on 5.2.11 on another Mac. Not really sure where to go next to debug it. I guess it could be an apache setting as much as a php bug or a problem with the code... any suggestions on where to look next?

  Read the article

• Debian 5 is randomly shutting down.

  - by revofreak

  My debian 5 vps is suffering from random shutdowns. I reinstalled it several times, the hosts moved me to a different physical box, check the install image and said everyone else also uses it and is fine. Heres the output from syslog Mar 27 00:19:19 noobintraining-1 -- MARK -- Mar 27 00:32:01 noobintraining-1 shutdown[18142]: shutting down for system halt Mar 27 00:32:06 noobintraining-1 init: Switching to runlevel: 0 Mar 27 00:32:06 noobintraining-1 xinetd[15907]: Exiting... Mar 27 00:32:07 noobintraining-1 named[15865]: received control channel command 'stop -p' Mar 27 00:32:07 noobintraining-1 named[15865]: shutting down: flushing changes Mar 27 00:32:07 noobintraining-1 named[15865]: stopping command channel on 127.0.0.1#953 Mar 27 00:32:07 noobintraining-1 named[15865]: stopping command channel on ::1#953 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on ::#53 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on 127.0.0.1#53 Mar 27 00:32:07 noobintraining-1 named[15865]: no longer listening on 89.238.172.132#53 Mar 27 00:32:07 noobintraining-1 named[15865]: exiting Mar 27 00:32:07 noobintraining-1 exiting on signal 15 Any help is most appreciated!

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• Usage of two Routers on LAN

  - by brusilva

  I've currently own a Linksys E4200 and a Thomson 546v6. Because I have an IPTV service I must set the Thomson as the main router connected to the phone line so that I can distribute the video signal for 2 specific ports and the other two for LAN Access. The problem is that the Thomson doesn't like port forwards, it usually doesnt work and since I have a good router (linksys) currently only working as Access Point I would like to use it as a router itself. I don't want to do a NAT beyond NAT so my question is should I connect the E4200 and to thomson and set the E4200 as a DMZ machine and then control all trafic on the E4200 itself or is there any other option that could suit my needs better?

  Read the article

• Public IP shows strange characters and Facebook registers logged-in session to a different location

  - by Stuart Kershaw

  I'm encountering some IP strangeness today and hoping to find an explanation. In short, I'm based in Seattle, WA with my ISP being Comcast. While browsing Facebook's account settings, I noticed that my active session was located to Mount Laurel, NJ. At that point I ran a search in Google for 'my public IP', which returned an interesting result: a string of characters in the following format: 2601:8:b000:xxx:xxxx:xxxx:xxxx:xxxx Normally, a search for my IP returns something like: 67.xxx.xx.xxx A phone call to Comcast got me nowhere, but using Comcast's phone-menu debugging tools, I was able to send a 'refresh signal' to my modem. After that, the search for 'my public IP' yielded the expected result... for about 5 minutes, and then it returned to the new string of characters. Does anyone know of an explanation for this?

  Read the article

• How can we connect TP-link Access Point- TL-WA5210G with Wifi Lan card?

  - by PPS

  I would like to know that, We have a small Wireless Network that covers 40 mtrs indoor. Now we plan to expand our Network Coverage area apporx. 200 Mtrs (Outdoor). Due to our requirement we used TP- Link Access Point TL-WA5210G Outdoor(This AP covers 15Km area). We have 3 blocks between 200 mtrs, We like to connect all the laptops Lan Card directly with required Access-point. What should we do to achieve this, right now we are not getting the full strength signal, when we cross the 80 mtrs. So please suggest me proper configuration for implementing this TP-Link access point. Thanks PPS

  Read the article

• My Macbook Pro wifi intermittently won't turn on sometimes after sleep, does anyone know how to solve this?

  - by Simon

  Hello, My current-generation MacBook Pro 15" (10.6.5) intermittently has problems turning the wifi (airport) on. The usual symptom happens when I: Sleep the machine Open from sleep Wifi is off (the airport signal is blank) I click on airport icon-Turn Airport On, but nothing happens. I googled around a bit and found one recommended solution where I delete the "automatic" location and create a new one and enable the wifi, or I delete the "AirPort" from the location and add it back, but neither of these resolve the problem. I also called AppleCare and they had me delete /Library/SystemConfiguration and restart, but that hasn't solved the problem. I have to reboot, which is very painful. Does anyone have any idea of how to solve this?

  Read the article

• Remote kill, upload, execute file

  - by Masoud M.

  I'm developing a program and I need to upload my xyz.exe file to many host machines and execute them frequently. I need a server-client tool to do it as below steps after an update signal from my PC: Those host machine should kill any running processes with name xyz.exe. Download my new xyz.exe. Then execute new xyz.exe. I know about some tools like PsExec, but I need a tools with better user-interface and more powerful. Is there any tool to do it ? UPDATE: The systems are in a same LAN, OS is windows (XP or 7), No full remote access is needed. I'm a developer and my program should run in remote hosts and I'm testing my application.

  Read the article

• Windows - Force Wi-Fi to N mode

  - by Frederick Marcoux

  I bought a month ago the D-Link DWA-160 Xtreme N Dual Band USB Adapter and I wonder about the speed. I have a 60Mbps but the speed is never above 300Kbps when I browse Internet or download something. Even from Microsoft or Apple (the fastest server I found). Now on Windows 8, we can see the Wi-Fi stats in Task Manager, there they are: Notice the red rectangle. The signal is 3/5 and I'm about 5 meters far from my router. An Apple Time-Capsule. Also, the connection type is 802.11g, I want N. I made this config in my Device Properties: Does anyone figured out to force the 802.11n in Windows? (Windows 8 preferably)

  Read the article

• Determining Namespaces Not in the ACPI Spec

  - by Eddie B

  I am trying to determine how it may be possible to find documentation for namespaces that are not documented in the ACPI spec. I have an Asus uEFI BIOS v(3202) and I'm receiving kernel messages stating AE Namespace lookup failures for DSSP. This is referring to a namespace that is not in the ACPI spec. I'm presuming that this is vendor specific and refers to a Digital Sensor Signal Processor. That is only a presumption. In an effort to correct ACPI errors I have dumped my DSDT using acpidump and then decompiled it using iASL. Yet to fix the error I need to know the spec on the namespace. How can I get access to the BIOS documentation that isn't part of the ACPI spec?

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >